i40e: add adminq commands for Rx CTL registers

Add the new opcodes and struct used for asking the firmware to update Rx
control registers that need extra care when being accessed while under
heavy traffic - e.g. sustained 64byte packets at line rate on all ports.
The firmware will take extra steps to be sure the register accesses
are successful.

The registers involved are:
	PFQF_CTL_0
	PFQF_HENA
	PFQF_FDALLOC
	PFQF_HREGION
	PFLAN_QALLOC
	VPQF_CTL
	VFQF_HENA
	VFQF_HREGION
	VSIQF_CTL
	VSILAN_QBASE
	VSILAN_QTABLE
	VSIQF_TCREGION
	PFQF_HKEY
	VFQF_HKEY
	PRTQF_CTL_0
	GLFCOE_RCTL
	GLFCOE_RSOF
	GLQF_CTL
	GLQF_SWAP
	GLQF_HASH_MSK
	GLQF_HASH_INSET
	GLQF_HSYM
	GLQF_FC_MSK
	GLQF_FC_INSET
	GLQF_FD_MSK
	PRTQF_FD_INSET
	PRTQF_FD_FLXINSET
	PRTQF_FD_MSK

Change-ID: I56c8144000da66ad99f68948d8a184b2ec2aeb3e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h

@@ -146,6 +146,8 @@ enum i40e_admin_queue_opc {
 	i40e_aqc_opc_set_port_parameters	= 0x0203,
 	i40e_aqc_opc_get_switch_resource_alloc	= 0x0204,
 	i40e_aqc_opc_set_switch_config		= 0x0205,
+	i40e_aqc_opc_rx_ctl_reg_read		= 0x0206,
+	i40e_aqc_opc_rx_ctl_reg_write		= 0x0207,
 
 	i40e_aqc_opc_add_vsi			= 0x0210,
 	i40e_aqc_opc_update_vsi_parameters	= 0x0211,
@@ -696,6 +698,20 @@ struct i40e_aqc_set_switch_config {
 
 I40E_CHECK_CMD_LENGTH(i40e_aqc_set_switch_config);
 
+/* Read Receive control registers  (direct 0x0206)
+ * Write Receive control registers (direct 0x0207)
+ *     used for accessing Rx control registers that can be
+ *     slow and need special handling when under high Rx load
+ */
+struct i40e_aqc_rx_ctl_reg_read_write {
+	__le32 reserved1;
+	__le32 address;
+	__le32 reserved2;
+	__le32 value;
+};
+
+I40E_CHECK_CMD_LENGTH(i40e_aqc_rx_ctl_reg_read_write);
+
 /* Add VSI (indirect 0x0210)
  *    this indirect command uses struct i40e_aqc_vsi_properties_data
  *    as the indirect buffer (128 bytes)

drivers/net/ethernet/intel/i40evf/i40e_adminq_cmd.h

@@ -146,6 +146,8 @@ enum i40e_admin_queue_opc {
 	i40e_aqc_opc_set_port_parameters	= 0x0203,
 	i40e_aqc_opc_get_switch_resource_alloc	= 0x0204,
 	i40e_aqc_opc_set_switch_config		= 0x0205,
+	i40e_aqc_opc_rx_ctl_reg_read		= 0x0206,
+	i40e_aqc_opc_rx_ctl_reg_write		= 0x0207,
 
 	i40e_aqc_opc_add_vsi			= 0x0210,
 	i40e_aqc_opc_update_vsi_parameters	= 0x0211,
@@ -693,6 +695,20 @@ struct i40e_aqc_set_switch_config {
 
 I40E_CHECK_CMD_LENGTH(i40e_aqc_set_switch_config);
 
+/* Read Receive control registers  (direct 0x0206)
+ * Write Receive control registers (direct 0x0207)
+ *     used for accessing Rx control registers that can be
+ *     slow and need special handling when under high Rx load
+ */
+struct i40e_aqc_rx_ctl_reg_read_write {
+	__le32 reserved1;
+	__le32 address;
+	__le32 reserved2;
+	__le32 value;
+};
+
+I40E_CHECK_CMD_LENGTH(i40e_aqc_rx_ctl_reg_read_write);
+
 /* Add VSI (indirect 0x0210)
  *    this indirect command uses struct i40e_aqc_vsi_properties_data
  *    as the indirect buffer (128 bytes)