rt2x00: move under ralink vendor directory

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

MAINTAINERS

@@ -8801,7 +8801,7 @@ M:	Stanislaw Gruszka <sgruszka@redhat.com>
 M:	Helmut Schaa <helmut.schaa@googlemail.com>
 L:	linux-wireless@vger.kernel.org
 S:	Maintained
-F:	drivers/net/wireless/rt2x00/
+F:	drivers/net/wireless/ralink/rt2x00/
 
 RAMDISK RAM BLOCK DEVICE DRIVER
 M:	Jens Axboe <axboe@kernel.dk>

drivers/net/wireless/Kconfig

@@ -24,6 +24,7 @@ source "drivers/net/wireless/cisco/Kconfig"
 source "drivers/net/wireless/intel/Kconfig"
 source "drivers/net/wireless/intersil/Kconfig"
 source "drivers/net/wireless/marvell/Kconfig"
+source "drivers/net/wireless/ralink/Kconfig"
 source "drivers/net/wireless/realtek/Kconfig"
 source "drivers/net/wireless/rsi/Kconfig"
 source "drivers/net/wireless/st/Kconfig"
@@ -97,7 +98,6 @@ config MAC80211_HWSIM
 	  called mac80211_hwsim.  If unsure, say N.
 
 source "drivers/net/wireless/ath/Kconfig"
-source "drivers/net/wireless/rt2x00/Kconfig"
 source "drivers/net/wireless/mediatek/Kconfig"
 source "drivers/net/wireless/ti/Kconfig"
 

drivers/net/wireless/Makefile

@@ -9,6 +9,7 @@ obj-$(CONFIG_WLAN_VENDOR_CISCO) += cisco/
 obj-$(CONFIG_WLAN_VENDOR_INTEL) += intel/
 obj-$(CONFIG_WLAN_VENDOR_INTERSIL) += intersil/
 obj-$(CONFIG_WLAN_VENDOR_MARVELL) += marvell/
+obj-$(CONFIG_WLAN_VENDOR_RALINK) += ralink/
 obj-$(CONFIG_WLAN_VENDOR_REALTEK) += realtek/
 obj-$(CONFIG_WLAN_VENDOR_RSI) += rsi/
 obj-$(CONFIG_WLAN_VENDOR_ST) += st/
@@ -20,8 +21,6 @@ obj-$(CONFIG_PCMCIA_WL3501)	+= wl3501_cs.o
 
 obj-$(CONFIG_USB_NET_RNDIS_WLAN)	+= rndis_wlan.o
 
-obj-$(CONFIG_RT2X00)	+= rt2x00/
-
 obj-$(CONFIG_WL_MEDIATEK)	+= mediatek/
 
 obj-$(CONFIG_ATH_CARDS)		+= ath/

drivers/net/wireless/ralink/Kconfig

+config WLAN_VENDOR_RALINK
+	bool "Ralink devices"
+	default y
+	---help---
+	  If you have a wireless card belonging to this class, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about  cards. If you say Y, you will be asked for
+	  your specific card in the following questions.
+
+if WLAN_VENDOR_RALINK
+
+source "drivers/net/wireless/ralink/rt2x00/Kconfig"
+
+endif # WLAN_VENDOR_RALINK

drivers/net/wireless/ralink/Makefile

+obj-$(CONFIG_RT2X00)	+= rt2x00/