[POWERPC] Copy over headers from arch/ppc to arch/powerpc that we need

To build arch/powerpc without including asm-ppc/ we need these files
in asm-powerpc/

Moved some headers under arch/powerpc/platforms if they were only used by
platform or driver files and fixed up the source file includes to match
the new locations
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

arch/powerpc/platforms/chrp/gg2.h

+/*
+ *  include/asm-ppc/gg2.h -- VLSI VAS96011/12 `Golden Gate 2' register definitions
+ *
+ *  Copyright (C) 1997 Geert Uytterhoeven
+ *
+ *  This file is based on the following documentation:
+ *
+ *	The VAS96011/12 Chipset, Data Book, Edition 1.0
+ *	VLSI Technology, Inc.
+ *
+ *  This file is subject to the terms and conditions of the GNU General Public
+ *  License.  See the file COPYING in the main directory of this archive
+ *  for more details.
+ */
+
+#ifndef _ASMPPC_GG2_H
+#define _ASMPPC_GG2_H
+
+    /*
+     *  Memory Map (CHRP mode)
+     */
+
+#define GG2_PCI_MEM_BASE	0xc0000000	/* Peripheral memory space */
+#define GG2_ISA_MEM_BASE	0xf7000000	/* Peripheral memory alias */
+#define GG2_ISA_IO_BASE		0xf8000000	/* Peripheral I/O space */
+#define GG2_PCI_CONFIG_BASE	0xfec00000	/* PCI configuration space */
+#define GG2_INT_ACK_SPECIAL	0xfec80000	/* Interrupt acknowledge and */
+						/* special PCI cycles */
+#define GG2_ROM_BASE0		0xff000000	/* ROM bank 0 */
+#define GG2_ROM_BASE1		0xff800000	/* ROM bank 1 */
+
+
+    /*
+     *  GG2 specific PCI Registers
+     */
+
+extern void __iomem *gg2_pci_config_base;	/* kernel virtual address */
+
+#define GG2_PCI_BUSNO		0x40	/* Bus number */
+#define GG2_PCI_SUBBUSNO	0x41	/* Subordinate bus number */
+#define GG2_PCI_DISCCTR		0x42	/* Disconnect counter */
+#define GG2_PCI_PPC_CTRL	0x50	/* PowerPC interface control register */
+#define GG2_PCI_ADDR_MAP	0x5c	/* Address map */
+#define GG2_PCI_PCI_CTRL	0x60	/* PCI interface control register */
+#define GG2_PCI_ROM_CTRL	0x70	/* ROM interface control register */
+#define GG2_PCI_ROM_TIME	0x74	/* ROM timing */
+#define GG2_PCI_CC_CTRL		0x80	/* Cache controller control register */
+#define GG2_PCI_DRAM_BANK0	0x90	/* Control register for DRAM bank #0 */
+#define GG2_PCI_DRAM_BANK1	0x94	/* Control register for DRAM bank #1 */
+#define GG2_PCI_DRAM_BANK2	0x98	/* Control register for DRAM bank #2 */
+#define GG2_PCI_DRAM_BANK3	0x9c	/* Control register for DRAM bank #3 */
+#define GG2_PCI_DRAM_BANK4	0xa0	/* Control register for DRAM bank #4 */
+#define GG2_PCI_DRAM_BANK5	0xa4	/* Control register for DRAM bank #5 */
+#define GG2_PCI_DRAM_TIME0	0xb0	/* Timing parameters set #0 */
+#define GG2_PCI_DRAM_TIME1	0xb4	/* Timing parameters set #1 */
+#define GG2_PCI_DRAM_CTRL	0xc0	/* DRAM control */
+#define GG2_PCI_ERR_CTRL	0xd0	/* Error control register */
+#define GG2_PCI_ERR_STATUS	0xd4	/* Error status register */
+					/* Cleared when read */
+
+#endif /* _ASMPPC_GG2_H */

arch/powerpc/platforms/chrp/pci.c

@@ -13,7 +13,6 @@
 #include <asm/irq.h>
 #include <asm/hydra.h>
 #include <asm/prom.h>
-#include <asm/gg2.h>
 #include <asm/machdep.h>
 #include <asm/sections.h>
 #include <asm/pci-bridge.h>
@@ -21,6 +20,7 @@
 #include <asm/rtas.h>
 
 #include "chrp.h"
+#include "gg2.h"
 
 /* LongTrail */
 void __iomem *gg2_pci_config_base;

arch/powerpc/platforms/chrp/setup.c

@@ -37,7 +37,6 @@
 #include <asm/io.h>
 #include <asm/pgtable.h>
 #include <asm/prom.h>
-#include <asm/gg2.h>
 #include <asm/pci-bridge.h>
 #include <asm/dma.h>
 #include <asm/machdep.h>
@@ -51,6 +50,7 @@
 #include <asm/xmon.h>
 
 #include "chrp.h"
+#include "gg2.h"
 
 void rtas_indicator_progress(char *, unsigned short);
 

arch/powerpc/platforms/embedded6xx/linkstation.c

@@ -18,9 +18,10 @@
 #include <asm/time.h>
 #include <asm/prom.h>
 #include <asm/mpic.h>
-#include <asm/mpc10x.h>
 #include <asm/pci-bridge.h>
 
+#include "mpc10x.h"
+
 static struct mtd_partition linkstation_physmap_partitions[] = {
 	{
 		.name   = "mtd_firmimg",

arch/powerpc/platforms/embedded6xx/ls_uart.c

@@ -4,10 +4,11 @@
 #include <linux/serial_reg.h>
 #include <linux/serial_8250.h>
 #include <asm/io.h>
-#include <asm/mpc10x.h>
 #include <asm/prom.h>
 #include <asm/termbits.h>
 
+#include "mpc10x.h"
+
 static void __iomem *avr_addr;
 static unsigned long avr_clock;
 

arch/powerpc/platforms/embedded6xx/mpc10x.h

+/*
+ * Common routines for the Motorola SPS MPC106/8240/107 Host bridge/Mem
+ * ctlr/EPIC/etc.
+ *
+ * Author: Mark A. Greer
+ *         mgreer@mvista.com
+ *
+ * 2001 (c) MontaVista, Software, Inc.  This file is licensed under
+ * the terms of the GNU General Public License version 2.  This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+#ifndef __PPC_KERNEL_MPC10X_H
+#define __PPC_KERNEL_MPC10X_H
+
+#include <linux/pci_ids.h>
+#include <asm/pci-bridge.h>
+
+/*
+ * The values here don't completely map everything but should work in most
+ * cases.
+ *
+ * MAP A (PReP Map)
+ *   Processor: 0x80000000 - 0x807fffff -> PCI I/O: 0x00000000 - 0x007fffff
+ *   Processor: 0xc0000000 - 0xdfffffff -> PCI MEM: 0x00000000 - 0x1fffffff
+ *   PCI MEM:   0x80000000 -> Processor System Memory: 0x00000000
+ *   EUMB mapped to: ioremap_base - 0x00100000 (ioremap_base - 1 MB)
+ *
+ * MAP B (CHRP Map)
+ *   Processor: 0xfe000000 - 0xfebfffff -> PCI I/O: 0x00000000 - 0x00bfffff
+ *   Processor: 0x80000000 - 0xbfffffff -> PCI MEM: 0x80000000 - 0xbfffffff
+ *   PCI MEM:   0x00000000 -> Processor System Memory: 0x00000000
+ *   EUMB mapped to: ioremap_base - 0x00100000 (ioremap_base - 1 MB)
+ */
+
+/*
+ * Define the vendor/device IDs for the various bridges--should be added to
+ * <linux/pci_ids.h>
+ */
+#define	MPC10X_BRIDGE_106	((PCI_DEVICE_ID_MOTOROLA_MPC106 << 16) |  \
+				  PCI_VENDOR_ID_MOTOROLA)
+#define	MPC10X_BRIDGE_8240	((0x0003 << 16) | PCI_VENDOR_ID_MOTOROLA)
+#define	MPC10X_BRIDGE_107	((0x0004 << 16) | PCI_VENDOR_ID_MOTOROLA)
+#define	MPC10X_BRIDGE_8245	((0x0006 << 16) | PCI_VENDOR_ID_MOTOROLA)
+
+/* Define the type of map to use */
+#define	MPC10X_MEM_MAP_A		1
+#define	MPC10X_MEM_MAP_B		2
+
+/* Map A (PReP Map) Defines */
+#define	MPC10X_MAPA_CNFG_ADDR		0x80000cf8
+#define	MPC10X_MAPA_CNFG_DATA		0x80000cfc
+
+#define MPC10X_MAPA_ISA_IO_BASE		0x80000000
+#define MPC10X_MAPA_ISA_MEM_BASE	0xc0000000
+#define	MPC10X_MAPA_DRAM_OFFSET		0x80000000
+
+#define	MPC10X_MAPA_PCI_INTACK_ADDR	0xbffffff0
+#define	MPC10X_MAPA_PCI_IO_START	0x00000000
+#define	MPC10X_MAPA_PCI_IO_END	       (0x00800000 - 1)
+#define	MPC10X_MAPA_PCI_MEM_START	0x00000000
+#define	MPC10X_MAPA_PCI_MEM_END	       (0x20000000 - 1)
+
+#define	MPC10X_MAPA_PCI_MEM_OFFSET	(MPC10X_MAPA_ISA_MEM_BASE -	\
+					 MPC10X_MAPA_PCI_MEM_START)
+
+/* Map B (CHRP Map) Defines */
+#define	MPC10X_MAPB_CNFG_ADDR		0xfec00000
+#define	MPC10X_MAPB_CNFG_DATA		0xfee00000
+
+#define MPC10X_MAPB_ISA_IO_BASE		0xfe000000
+#define MPC10X_MAPB_ISA_MEM_BASE	0x80000000
+#define	MPC10X_MAPB_DRAM_OFFSET		0x00000000
+
+#define	MPC10X_MAPB_PCI_INTACK_ADDR	0xfef00000
+#define	MPC10X_MAPB_PCI_IO_START	0x00000000
+#define	MPC10X_MAPB_PCI_IO_END	       (0x00c00000 - 1)
+#define	MPC10X_MAPB_PCI_MEM_START	0x80000000
+#define	MPC10X_MAPB_PCI_MEM_END	       (0xc0000000 - 1)
+
+#define	MPC10X_MAPB_PCI_MEM_OFFSET	(MPC10X_MAPB_ISA_MEM_BASE -	\
+					 MPC10X_MAPB_PCI_MEM_START)
+
+/* Set hose members to values appropriate for the mem map used */
+#define	MPC10X_SETUP_HOSE(hose, map) {					\
+	(hose)->pci_mem_offset = MPC10X_MAP##map##_PCI_MEM_OFFSET;	\
+	(hose)->io_space.start = MPC10X_MAP##map##_PCI_IO_START;	\
+	(hose)->io_space.end = MPC10X_MAP##map##_PCI_IO_END;		\
+	(hose)->mem_space.start = MPC10X_MAP##map##_PCI_MEM_START;	\
+	(hose)->mem_space.end = MPC10X_MAP##map##_PCI_MEM_END;		\
+	(hose)->io_base_virt = (void *)MPC10X_MAP##map##_ISA_IO_BASE;	\
+}
+
+
+/* Miscellaneous Configuration register offsets */
+#define	MPC10X_CFG_PIR_REG		0x09
+#define	MPC10X_CFG_PIR_HOST_BRIDGE	0x00
+#define	MPC10X_CFG_PIR_AGENT		0x01
+
+#define	MPC10X_CFG_EUMBBAR		0x78
+
+#define	MPC10X_CFG_PICR1_REG		0xa8
+#define	MPC10X_CFG_PICR1_ADDR_MAP_MASK	0x00010000
+#define	MPC10X_CFG_PICR1_ADDR_MAP_A	0x00010000
+#define	MPC10X_CFG_PICR1_ADDR_MAP_B	0x00000000
+#define	MPC10X_CFG_PICR1_SPEC_PCI_RD	0x00000004
+#define	MPC10X_CFG_PICR1_ST_GATH_EN	0x00000040
+
+#define	MPC10X_CFG_PICR2_REG		0xac
+#define	MPC10X_CFG_PICR2_COPYBACK_OPT	0x00000001
+
+#define	MPC10X_CFG_MAPB_OPTIONS_REG	0xe0
+#define	MPC10X_CFG_MAPB_OPTIONS_CFAE	0x80	/* CPU_FD_ALIAS_EN */
+#define	MPC10X_CFG_MAPB_OPTIONS_PFAE	0x40	/* PCI_FD_ALIAS_EN */
+#define	MPC10X_CFG_MAPB_OPTIONS_DR	0x20	/* DLL_RESET */
+#define	MPC10X_CFG_MAPB_OPTIONS_PCICH	0x08	/* PCI_COMPATIBILITY_HOLE */
+#define	MPC10X_CFG_MAPB_OPTIONS_PROCCH	0x04	/* PROC_COMPATIBILITY_HOLE */
+
+/* Define offsets for the memory controller registers in the config space */
+#define MPC10X_MCTLR_MEM_START_1	0x80	/* Banks 0-3 */
+#define MPC10X_MCTLR_MEM_START_2	0x84	/* Banks 4-7 */
+#define MPC10X_MCTLR_EXT_MEM_START_1	0x88	/* Banks 0-3 */
+#define MPC10X_MCTLR_EXT_MEM_START_2	0x8c	/* Banks 4-7 */
+
+#define MPC10X_MCTLR_MEM_END_1		0x90	/* Banks 0-3 */
+#define MPC10X_MCTLR_MEM_END_2		0x94	/* Banks 4-7 */
+#define MPC10X_MCTLR_EXT_MEM_END_1	0x98	/* Banks 0-3 */
+#define MPC10X_MCTLR_EXT_MEM_END_2	0x9c	/* Banks 4-7 */
+
+#define MPC10X_MCTLR_MEM_BANK_ENABLES	0xa0
+
+/* Define some offset in the EUMB */
+#define	MPC10X_EUMB_SIZE		0x00100000 /* Total EUMB size (1MB) */
+
+#define MPC10X_EUMB_MU_OFFSET		0x00000000 /* Msg Unit reg offset */
+#define MPC10X_EUMB_MU_SIZE		0x00001000 /* Msg Unit reg size */
+#define MPC10X_EUMB_DMA_OFFSET		0x00001000 /* DMA Unit reg offset */
+#define MPC10X_EUMB_DMA_SIZE		0x00001000 /* DMA Unit reg size  */
+#define MPC10X_EUMB_ATU_OFFSET		0x00002000 /* Addr xlate reg offset */
+#define MPC10X_EUMB_ATU_SIZE		0x00001000 /* Addr xlate reg size  */
+#define MPC10X_EUMB_I2C_OFFSET		0x00003000 /* I2C Unit reg offset */
+#define MPC10X_EUMB_I2C_SIZE		0x00001000 /* I2C Unit reg size  */
+#define MPC10X_EUMB_DUART_OFFSET	0x00004000 /* DUART Unit reg offset (8245) */
+#define MPC10X_EUMB_DUART_SIZE		0x00001000 /* DUART Unit reg size (8245) */
+#define	MPC10X_EUMB_EPIC_OFFSET		0x00040000 /* EPIC offset in EUMB */
+#define	MPC10X_EUMB_EPIC_SIZE		0x00030000 /* EPIC size */
+#define MPC10X_EUMB_PM_OFFSET		0x000fe000 /* Performance Monitor reg offset (8245) */
+#define MPC10X_EUMB_PM_SIZE		0x00001000 /* Performance Monitor reg size (8245) */
+#define MPC10X_EUMB_WP_OFFSET		0x000ff000 /* Data path diagnostic, watchpoint reg offset */
+#define MPC10X_EUMB_WP_SIZE		0x00001000 /* Data path diagnostic, watchpoint reg size */
+
+/*
+ * Define some recommended places to put the EUMB regs.
+ * For both maps, recommend putting the EUMB from 0xeff00000 to 0xefffffff.
+ */
+extern unsigned long			ioremap_base;
+#define	MPC10X_MAPA_EUMB_BASE		(ioremap_base - MPC10X_EUMB_SIZE)
+#define	MPC10X_MAPB_EUMB_BASE		MPC10X_MAPA_EUMB_BASE
+
+enum ppc_sys_devices {
+	MPC10X_IIC1,
+	MPC10X_DMA0,
+	MPC10X_DMA1,
+	MPC10X_UART0,
+	MPC10X_UART1,
+	NUM_PPC_SYS_DEVS,
+};
+
+int mpc10x_bridge_init(struct pci_controller *hose,
+		       uint current_map,
+		       uint new_map,
+		       uint phys_eumb_base);
+unsigned long mpc10x_get_mem_size(uint mem_map);
+int mpc10x_enable_store_gathering(struct pci_controller *hose);
+int mpc10x_disable_store_gathering(struct pci_controller *hose);
+
+/* For MPC107 boards that use the built-in openpic */
+void mpc10x_set_openpic(void);
+
+#endif	/* __PPC_KERNEL_MPC10X_H */

drivers/macintosh/ans-lcd.c

@@ -14,9 +14,10 @@
 #include <asm/uaccess.h>
 #include <asm/sections.h>
 #include <asm/prom.h>
-#include <asm/ans-lcd.h>
 #include <asm/io.h>
 
+#include "ans-lcd.h"
+
 #define ANSLCD_ADDR		0xf301c000
 #define ANSLCD_CTRL_IX 0x00
 #define ANSLCD_DATA_IX 0x10

include/asm-powerpc/highmem.h

+/*
+ * highmem.h: virtual kernel memory mappings for high memory
+ *
+ * PowerPC version, stolen from the i386 version.
+ *
+ * Used in CONFIG_HIGHMEM systems for memory pages which
+ * are not addressable by direct kernel virtual addresses.
+ *
+ * Copyright (C) 1999 Gerhard Wichert, Siemens AG
+ *		      Gerhard.Wichert@pdb.siemens.de
+ *
+ *
+ * Redesigned the x86 32-bit VM architecture to deal with
+ * up to 16 Terrabyte physical memory. With current x86 CPUs
+ * we now support up to 64 Gigabytes physical RAM.
+ *
+ * Copyright (C) 1999 Ingo Molnar <mingo@redhat.com>
+ */
+
+#ifndef _ASM_HIGHMEM_H
+#define _ASM_HIGHMEM_H
+
+#ifdef __KERNEL__
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/kmap_types.h>
+#include <asm/tlbflush.h>
+#include <asm/page.h>
+
+/* undef for production */
+#define HIGHMEM_DEBUG 1
+
+extern pte_t *kmap_pte;
+extern pgprot_t kmap_prot;
+extern pte_t *pkmap_page_table;
+
+/*
+ * Right now we initialize only a single pte table. It can be extended
+ * easily, subsequent pte tables have to be allocated in one physical
+ * chunk of RAM.
+ */
+#define PKMAP_BASE 	CONFIG_HIGHMEM_START
+#define LAST_PKMAP 	(1 << PTE_SHIFT)
+#define LAST_PKMAP_MASK (LAST_PKMAP-1)
+#define PKMAP_NR(virt)  ((virt-PKMAP_BASE) >> PAGE_SHIFT)
+#define PKMAP_ADDR(nr)  (PKMAP_BASE + ((nr) << PAGE_SHIFT))
+
+#define KMAP_FIX_BEGIN	(PKMAP_BASE + 0x00400000UL)
+
+extern void *kmap_high(struct page *page);
+extern void kunmap_high(struct page *page);
+
+static inline void *kmap(struct page *page)
+{
+	might_sleep();
+	if (!PageHighMem(page))
+		return page_address(page);
+	return kmap_high(page);
+}
+
+static inline void kunmap(struct page *page)
+{
+	BUG_ON(in_interrupt());
+	if (!PageHighMem(page))
+		return;
+	kunmap_high(page);
+}
+
+/*
+ * The use of kmap_atomic/kunmap_atomic is discouraged - kmap/kunmap
+ * gives a more generic (and caching) interface. But kmap_atomic can
+ * be used in IRQ contexts, so in some (very limited) cases we need
+ * it.
+ */
+static inline void *kmap_atomic(struct page *page, enum km_type type)
+{
+	unsigned int idx;
+	unsigned long vaddr;
+
+	/* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */
+	pagefault_disable();
+	if (!PageHighMem(page))
+		return page_address(page);
+
+	idx = type + KM_TYPE_NR*smp_processor_id();
+	vaddr = KMAP_FIX_BEGIN + idx * PAGE_SIZE;
+#ifdef HIGHMEM_DEBUG
+	BUG_ON(!pte_none(*(kmap_pte+idx)));
+#endif
+	set_pte_at(&init_mm, vaddr, kmap_pte+idx, mk_pte(page, kmap_prot));
+	flush_tlb_page(NULL, vaddr);
+
+	return (void*) vaddr;
+}
+
+static inline void kunmap_atomic(void *kvaddr, enum km_type type)
+{
+#ifdef HIGHMEM_DEBUG
+	unsigned long vaddr = (unsigned long) kvaddr & PAGE_MASK;
+	unsigned int idx = type + KM_TYPE_NR*smp_processor_id();
+
+	if (vaddr < KMAP_FIX_BEGIN) { // FIXME
+		pagefault_enable();
+		return;
+	}
+
+	BUG_ON(vaddr != KMAP_FIX_BEGIN + idx * PAGE_SIZE);
+
+	/*
+	 * force other mappings to Oops if they'll try to access
+	 * this pte without first remap it
+	 */
+	pte_clear(&init_mm, vaddr, kmap_pte+idx);
+	flush_tlb_page(NULL, vaddr);
+#endif
+	pagefault_enable();
+}
+
+static inline struct page *kmap_atomic_to_page(void *ptr)
+{
+	unsigned long idx, vaddr = (unsigned long) ptr;
+
+	if (vaddr < KMAP_FIX_BEGIN)
+		return virt_to_page(ptr);
+
+	idx = (vaddr - KMAP_FIX_BEGIN) >> PAGE_SHIFT;
+	return pte_page(kmap_pte[idx]);
+}
+
+#define flush_cache_kmaps()	flush_cache_all()
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_HIGHMEM_H */

include/asm-powerpc/hydra.h

+/*
+ *  include/asm-ppc/hydra.h -- Mac I/O `Hydra' definitions
+ *
+ *  Copyright (C) 1997 Geert Uytterhoeven
+ *
+ *  This file is based on the following documentation:
+ *
+ *	Macintosh Technology in the Common Hardware Reference Platform
+ *	Apple Computer, Inc.
+ *
+ *	© Copyright 1995 Apple Computer, Inc. All rights reserved.
+ *
+ *  It's available online from http://chrp.apple.com/MacTech.pdf.
+ *  You can obtain paper copies of this book from computer bookstores or by
+ *  writing Morgan Kaufmann Publishers, Inc., 340 Pine Street, Sixth Floor, San
+ *  Francisco, CA 94104. Reference ISBN 1-55860-393-X.
+ *
+ *  This file is subject to the terms and conditions of the GNU General Public
+ *  License.  See the file COPYING in the main directory of this archive
+ *  for more details.
+ */
+
+#ifndef _ASMPPC_HYDRA_H
+#define _ASMPPC_HYDRA_H
+
+#ifdef __KERNEL__
+
+struct Hydra {
+    /* DBDMA Controller Register Space */
+    char Pad1[0x30];
+    u_int CachePD;
+    u_int IDs;
+    u_int Feature_Control;
+    char Pad2[0x7fc4];
+    /* DBDMA Channel Register Space */
+    char SCSI_DMA[0x100];
+    char Pad3[0x300];
+    char SCCA_Tx_DMA[0x100];
+    char SCCA_Rx_DMA[0x100];
+    char SCCB_Tx_DMA[0x100];
+    char SCCB_Rx_DMA[0x100];
+    char Pad4[0x7800];
+    /* Device Register Space */
+    char SCSI[0x1000];
+    char ADB[0x1000];
+    char SCC_Legacy[0x1000];
+    char SCC[0x1000];
+    char Pad9[0x2000];
+    char VIA[0x2000];
+    char Pad10[0x28000];
+    char OpenPIC[0x40000];
+};
+
+extern volatile struct Hydra __iomem *Hydra;
+
+
+    /*
+     *  Feature Control Register
+     */
+
+#define HYDRA_FC_SCC_CELL_EN	0x00000001	/* Enable SCC Clock */
+#define HYDRA_FC_SCSI_CELL_EN	0x00000002	/* Enable SCSI Clock */
+#define HYDRA_FC_SCCA_ENABLE	0x00000004	/* Enable SCC A Lines */
+#define HYDRA_FC_SCCB_ENABLE	0x00000008	/* Enable SCC B Lines */
+#define HYDRA_FC_ARB_BYPASS	0x00000010	/* Bypass Internal Arbiter */
+#define HYDRA_FC_RESET_SCC	0x00000020	/* Reset SCC */
+#define HYDRA_FC_MPIC_ENABLE	0x00000040	/* Enable OpenPIC */
+#define HYDRA_FC_SLOW_SCC_PCLK	0x00000080	/* 1=15.6672, 0=25 MHz */
+#define HYDRA_FC_MPIC_IS_MASTER	0x00000100	/* OpenPIC Master Mode */
+
+
+    /*
+     *  OpenPIC Interrupt Sources
+     */
+
+#define HYDRA_INT_SIO		0
+#define HYDRA_INT_SCSI_DMA	1
+#define HYDRA_INT_SCCA_TX_DMA	2
+#define HYDRA_INT_SCCA_RX_DMA	3
+#define HYDRA_INT_SCCB_TX_DMA	4
+#define HYDRA_INT_SCCB_RX_DMA	5
+#define HYDRA_INT_SCSI		6
+#define HYDRA_INT_SCCA		7
+#define HYDRA_INT_SCCB		8
+#define HYDRA_INT_VIA		9
+#define HYDRA_INT_ADB		10
+#define HYDRA_INT_ADB_NMI	11
+#define HYDRA_INT_EXT1		12	/* PCI IRQW */
+#define HYDRA_INT_EXT2		13	/* PCI IRQX */
+#define HYDRA_INT_EXT3		14	/* PCI IRQY */
+#define HYDRA_INT_EXT4		15	/* PCI IRQZ */
+#define HYDRA_INT_EXT5		16	/* IDE Primay/Secondary */
+#define HYDRA_INT_EXT6		17	/* IDE Secondary */
+#define HYDRA_INT_EXT7		18	/* Power Off Request */
+#define HYDRA_INT_SPARE		19
+
+extern int hydra_init(void);
+extern void macio_adb_init(void);
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASMPPC_HYDRA_H */

include/asm-powerpc/kgdb.h

+/*
+ * kgdb.h: Defines and declarations for serial line source level
+ *         remote debugging of the Linux kernel using gdb.
+ *
+ * PPC Mods (C) 1998 Michael Tesch (tesch@cs.wisc.edu)
+ *
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ */
+#ifdef __KERNEL__
+#ifndef _PPC_KGDB_H
+#define _PPC_KGDB_H
+
+#ifndef __ASSEMBLY__
+
+/* Things specific to the gen550 backend. */
+struct uart_port;
+
+extern void gen550_progress(char *, unsigned short);
+extern void gen550_kgdb_map_scc(void);
+extern void gen550_init(int, struct uart_port *);
+
+/* Things specific to the pmac backend. */
+extern void zs_kgdb_hook(int tty_num);
+
+/* To init the kgdb engine. (called by serial hook)*/
+extern void set_debug_traps(void);
+
+/* To enter the debugger explicitly. */
+extern void breakpoint(void);
+
+/* For taking exceptions
+ * these are defined in traps.c
+ */
+extern int (*debugger)(struct pt_regs *regs);
+extern int (*debugger_bpt)(struct pt_regs *regs);
+extern int (*debugger_sstep)(struct pt_regs *regs);
+extern int (*debugger_iabr_match)(struct pt_regs *regs);
+extern int (*debugger_dabr_match)(struct pt_regs *regs);
+extern void (*debugger_fault_handler)(struct pt_regs *regs);
+
+/* What we bring to the party */
+int kgdb_bpt(struct pt_regs *regs);
+int kgdb_sstep(struct pt_regs *regs);
+void kgdb(struct pt_regs *regs);
+int kgdb_iabr_match(struct pt_regs *regs);
+int kgdb_dabr_match(struct pt_regs *regs);
+
+/*
+ * external low-level support routines (ie macserial.c)
+ */
+extern void kgdb_interruptible(int); /* control interrupts from serial */
+extern void putDebugChar(char);   /* write a single character      */
+extern char getDebugChar(void);   /* read and return a single char */
+
+#endif /* !(__ASSEMBLY__) */
+#endif /* !(_PPC_KGDB_H) */
+#endif /* __KERNEL__ */

include/asm-powerpc/mpc52xx_psc.h

+/*
+ * include/asm-ppc/mpc52xx_psc.h
+ *
+ * Definitions of consts/structs to drive the Freescale MPC52xx OnChip
+ * PSCs. Theses are shared between multiple drivers since a PSC can be
+ * UART, AC97, IR, I2S, ... So this header is in asm-ppc.
+ *
+ *
+ * Maintainer : Sylvain Munaut <tnt@246tNt.com>
+ *
+ * Based/Extracted from some header of the 2.4 originally written by
+ * Dale Farnsworth <dfarnsworth@mvista.com>
+ *
+ * Copyright (C) 2004 Sylvain Munaut <tnt@246tNt.com>
+ * Copyright (C) 2003 MontaVista, Software, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __ASM_MPC52xx_PSC_H__
+#define __ASM_MPC52xx_PSC_H__
+
+#include <asm/types.h>
+
+/* Max number of PSCs */
+#define MPC52xx_PSC_MAXNUM	6
+
+/* Programmable Serial Controller (PSC) status register bits */
+#define MPC52xx_PSC_SR_CDE	0x0080
+#define MPC52xx_PSC_SR_RXRDY	0x0100
+#define MPC52xx_PSC_SR_RXFULL	0x0200
+#define MPC52xx_PSC_SR_TXRDY	0x0400
+#define MPC52xx_PSC_SR_TXEMP	0x0800
+#define MPC52xx_PSC_SR_OE	0x1000
+#define MPC52xx_PSC_SR_PE	0x2000
+#define MPC52xx_PSC_SR_FE	0x4000
+#define MPC52xx_PSC_SR_RB	0x8000
+
+/* PSC Command values */
+#define MPC52xx_PSC_RX_ENABLE		0x0001
+#define MPC52xx_PSC_RX_DISABLE		0x0002
+#define MPC52xx_PSC_TX_ENABLE		0x0004
+#define MPC52xx_PSC_TX_DISABLE		0x0008
+#define MPC52xx_PSC_SEL_MODE_REG_1	0x0010
+#define MPC52xx_PSC_RST_RX		0x0020
+#define MPC52xx_PSC_RST_TX		0x0030
+#define MPC52xx_PSC_RST_ERR_STAT	0x0040
+#define MPC52xx_PSC_RST_BRK_CHG_INT	0x0050
+#define MPC52xx_PSC_START_BRK		0x0060
+#define MPC52xx_PSC_STOP_BRK		0x0070
+
+/* PSC TxRx FIFO status bits */
+#define MPC52xx_PSC_RXTX_FIFO_ERR	0x0040
+#define MPC52xx_PSC_RXTX_FIFO_UF	0x0020
+#define MPC52xx_PSC_RXTX_FIFO_OF	0x0010
+#define MPC52xx_PSC_RXTX_FIFO_FR	0x0008
+#define MPC52xx_PSC_RXTX_FIFO_FULL	0x0004
+#define MPC52xx_PSC_RXTX_FIFO_ALARM	0x0002
+#define MPC52xx_PSC_RXTX_FIFO_EMPTY	0x0001
+
+/* PSC interrupt mask bits */
+#define MPC52xx_PSC_IMR_TXRDY		0x0100
+#define MPC52xx_PSC_IMR_RXRDY		0x0200
+#define MPC52xx_PSC_IMR_DB		0x0400
+#define MPC52xx_PSC_IMR_IPC		0x8000
+
+/* PSC input port change bit */
+#define MPC52xx_PSC_CTS			0x01
+#define MPC52xx_PSC_DCD			0x02
+#define MPC52xx_PSC_D_CTS		0x10
+#define MPC52xx_PSC_D_DCD		0x20
+
+/* PSC mode fields */
+#define MPC52xx_PSC_MODE_5_BITS			0x00
+#define MPC52xx_PSC_MODE_6_BITS			0x01
+#define MPC52xx_PSC_MODE_7_BITS			0x02
+#define MPC52xx_PSC_MODE_8_BITS			0x03
+#define MPC52xx_PSC_MODE_BITS_MASK		0x03
+#define MPC52xx_PSC_MODE_PAREVEN		0x00
+#define MPC52xx_PSC_MODE_PARODD			0x04
+#define MPC52xx_PSC_MODE_PARFORCE		0x08
+#define MPC52xx_PSC_MODE_PARNONE		0x10
+#define MPC52xx_PSC_MODE_ERR			0x20
+#define MPC52xx_PSC_MODE_FFULL			0x40
+#define MPC52xx_PSC_MODE_RXRTS			0x80
+
+#define MPC52xx_PSC_MODE_ONE_STOP_5_BITS	0x00
+#define MPC52xx_PSC_MODE_ONE_STOP		0x07
+#define MPC52xx_PSC_MODE_TWO_STOP		0x0f
+
+#define MPC52xx_PSC_RFNUM_MASK	0x01ff
+
+
+/* Structure of the hardware registers */
+struct mpc52xx_psc {
+	u8		mode;		/* PSC + 0x00 */
+	u8		reserved0[3];
+	union {				/* PSC + 0x04 */
+		u16	status;
+		u16	clock_select;
+	} sr_csr;
+#define mpc52xx_psc_status	sr_csr.status
+#define mpc52xx_psc_clock_select sr_csr.clock_select
+	u16		reserved1;
+	u8		command;	/* PSC + 0x08 */
+	u8		reserved2[3];
+	union {				/* PSC + 0x0c */
+		u8	buffer_8;
+		u16	buffer_16;
+		u32	buffer_32;
+	} buffer;
+#define mpc52xx_psc_buffer_8	buffer.buffer_8
+#define mpc52xx_psc_buffer_16	buffer.buffer_16
+#define mpc52xx_psc_buffer_32	buffer.buffer_32
+	union {				/* PSC + 0x10 */
+		u8	ipcr;
+		u8	acr;
+	} ipcr_acr;
+#define mpc52xx_psc_ipcr	ipcr_acr.ipcr
+#define mpc52xx_psc_acr		ipcr_acr.acr
+	u8		reserved3[3];
+	union {				/* PSC + 0x14 */
+		u16	isr;
+		u16	imr;
+	} isr_imr;
+#define mpc52xx_psc_isr		isr_imr.isr
+#define mpc52xx_psc_imr		isr_imr.imr
+	u16		reserved4;
+	u8		ctur;		/* PSC + 0x18 */
+	u8		reserved5[3];
+	u8		ctlr;		/* PSC + 0x1c */
+	u8		reserved6[3];
+	u16		ccr;		/* PSC + 0x20 */
+	u8		reserved7[14];
+	u8		ivr;		/* PSC + 0x30 */
+	u8		reserved8[3];
+	u8		ip;		/* PSC + 0x34 */
+	u8		reserved9[3];
+	u8		op1;		/* PSC + 0x38 */
+	u8		reserved10[3];
+	u8		op0;		/* PSC + 0x3c */
+	u8		reserved11[3];
+	u32		sicr;		/* PSC + 0x40 */
+	u8		ircr1;		/* PSC + 0x44 */
+	u8		reserved13[3];
+	u8		ircr2;		/* PSC + 0x44 */
+	u8		reserved14[3];
+	u8		irsdr;		/* PSC + 0x4c */
+	u8		reserved15[3];
+	u8		irmdr;		/* PSC + 0x50 */
+	u8		reserved16[3];
+	u8		irfdr;		/* PSC + 0x54 */
+	u8		reserved17[3];
+	u16		rfnum;		/* PSC + 0x58 */
+	u16		reserved18;
+	u16		tfnum;		/* PSC + 0x5c */
+	u16		reserved19;
+	u32		rfdata;		/* PSC + 0x60 */
+	u16		rfstat;		/* PSC + 0x64 */
+	u16		reserved20;
+	u8		rfcntl;		/* PSC + 0x68 */
+	u8		reserved21[5];
+	u16		rfalarm;	/* PSC + 0x6e */
+	u16		reserved22;
+	u16		rfrptr;		/* PSC + 0x72 */
+	u16		reserved23;
+	u16		rfwptr;		/* PSC + 0x76 */
+	u16		reserved24;
+	u16		rflrfptr;	/* PSC + 0x7a */
+	u16		reserved25;
+	u16		rflwfptr;	/* PSC + 0x7e */
+	u32		tfdata;		/* PSC + 0x80 */
+	u16		tfstat;		/* PSC + 0x84 */
+	u16		reserved26;
+	u8		tfcntl;		/* PSC + 0x88 */
+	u8		reserved27[5];
+	u16		tfalarm;	/* PSC + 0x8e */
+	u16		reserved28;
+	u16		tfrptr;		/* PSC + 0x92 */
+	u16		reserved29;
+	u16		tfwptr;		/* PSC + 0x96 */
+	u16		reserved30;
+	u16		tflrfptr;	/* PSC + 0x9a */
+	u16		reserved31;
+	u16		tflwfptr;	/* PSC + 0x9e */
+};
+
+
+#endif  /* __ASM_MPC52xx_PSC_H__ */