Merge branch 'remotes/lorenzo/pci/amlogic'

  - Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)

* remotes/lorenzo/pci/amlogic:
  PCI: amlogic: Add the Amlogic Meson PCIe controller driver
  dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller

Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt

+Amlogic Meson AXG DWC PCIE SoC controller
+
+Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
+It shares common functions with the PCIe DesignWare core driver and
+inherits common properties defined in
+Documentation/devicetree/bindings/pci/designware-pci.txt.
+
+Additional properties are described here:
+
+Required properties:
+- compatible:
+	should contain "amlogic,axg-pcie" to identify the core.
+- reg:
+	should contain the configuration address space.
+- reg-names: Must be
+	- "elbi"	External local bus interface registers
+	- "cfg"		Meson specific registers
+	- "phy"		Meson PCIE PHY registers
+	- "config"	PCIe configuration space
+- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Must include the following entries:
+	- "pclk"       PCIe GEN 100M PLL clock
+	- "port"       PCIe_x(A or B) RC clock gate
+	- "general"    PCIe Phy clock
+	- "mipi"       PCIe_x(A or B) 100M ref clock gate
+- resets: phandle to the reset lines.
+- reset-names: must contain "phy" "port" and "apb"
+       - "phy"         Share PHY reset
+       - "port"        Port A or B reset
+       - "apb"         Share APB reset
+- device_type:
+	should be "pci". As specified in designware-pcie.txt
+
+
+Example configuration:
+
+	pcie: pcie@f9800000 {
+			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
+			reg = <0x0 0xf9800000 0x0 0x400000
+					0x0 0xff646000 0x0 0x2000
+					0x0 0xff644000 0x0 0x2000
+					0x0 0xf9f00000 0x0 0x100000>;
+			reg-names = "elbi", "cfg", "phy", "config";
+			reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
+			bus-range = <0x0 0xff>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
+
+			clocks = <&clkc CLKID_USB
+					&clkc CLKID_MIPI_ENABLE
+					&clkc CLKID_PCIE_A
+					&clkc CLKID_PCIE_CML_EN0>;
+			clock-names = "general",
+					"mipi",
+					"pclk",
+					"port";
+			resets = <&reset RESET_PCIE_PHY>,
+				<&reset RESET_PCIE_A>,
+				<&reset RESET_PCIE_APB>;
+			reset-names = "phy",
+					"port",
+					"apb";
+	};

MAINTAINERS

@@ -11510,6 +11510,13 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/pci.git/
 S:	Supported
 F:	drivers/pci/controller/
 
+PCIE DRIVER FOR AMLOGIC MESON
+M:	Yue Wang <yue.wang@Amlogic.com>
+L:	linux-pci@vger.kernel.org
+L:	linux-amlogic@lists.infradead.org
+S:	Maintained
+F:	drivers/pci/controller/dwc/pci-meson.c
+
 PCIE DRIVER FOR AXIS ARTPEC
 M:	Jesper Nilsson <jesper.nilsson@axis.com>
 L:	linux-arm-kernel@axis.com

drivers/pci/controller/dwc/Kconfig

@@ -193,4 +193,14 @@ config PCIE_HISI_STB
 	help
           Say Y here if you want PCIe controller support on HiSilicon STB SoCs
 
+config PCI_MESON
+	bool "MESON PCIe controller"
+	depends on PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want to enable PCI controller support on Amlogic
+	  SoCs. The PCI controller on Amlogic is based on DesignWare hardware
+	  and therefore the driver re-uses the DesignWare core functions to
+	  implement the driver.
+
 endmenu

drivers/pci/controller/dwc/Makefile

@@ -14,6 +14,7 @@ obj-$(CONFIG_PCIE_ARMADA_8K) += pcie-armada8k.o
 obj-$(CONFIG_PCIE_ARTPEC6) += pcie-artpec6.o
 obj-$(CONFIG_PCIE_KIRIN) += pcie-kirin.o
 obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
+obj-$(CONFIG_PCI_MESON) += pci-meson.o
 
 # The following drivers are for devices that use the generic ACPI
 # pci_root.c driver but don't support standard ECAM config access.