Merge branch 'omap-for-v5.2/am4-ddr3' into omap-for-v5.2/am4-pm-v2

arch/arm/mach-omap2/sleep43xx.S

@@ -368,6 +368,9 @@ wait_emif_enable1:
 	mov     r1, #AM43XX_EMIF_POWEROFF_DISABLE
 	str     r1, [r2, #0x0]
 
+	ldr     r1, [r9, #EMIF_PM_RUN_HW_LEVELING]
+	blx     r1
+
 #ifdef CONFIG_CACHE_L2X0
 	ldr	r2, l2_cache_base
 	ldr	r0, [r2, #L2X0_CTRL]

drivers/memory/emif.h

@@ -537,6 +537,9 @@
 #define MCONNID_SHIFT					0
 #define MCONNID_MASK					(0xff << 0)
 
+/* READ_WRITE_LEVELING_CONTROL */
+#define RDWRLVLFULL_START				0x80000000
+
 /* DDR_PHY_CTRL_1 - EMIF4D */
 #define DLL_SLAVE_DLY_CTRL_SHIFT_4D			4
 #define DLL_SLAVE_DLY_CTRL_MASK_4D			(0xFF << 4)
@@ -598,6 +601,7 @@ extern struct emif_regs_amx3 ti_emif_regs_amx3;
 
 void ti_emif_save_context(void);
 void ti_emif_restore_context(void);
+void ti_emif_run_hw_leveling(void);
 void ti_emif_enter_sr(void);
 void ti_emif_exit_sr(void);
 void ti_emif_abort_sr(void);

drivers/memory/ti-emif-pm.c

@@ -138,6 +138,9 @@ static int ti_emif_alloc_sram(struct device *dev,
 	emif_data->pm_functions.exit_sr =
 		sram_resume_address(emif_data,
 				    (unsigned long)ti_emif_exit_sr);
+	emif_data->pm_functions.run_hw_leveling =
+		sram_resume_address(emif_data,
+				    (unsigned long)ti_emif_run_hw_leveling);
 
 	emif_data->pm_data.regs_virt =
 		(struct emif_regs_amx3 *)emif_data->ti_emif_sram_data_virt;

drivers/memory/ti-emif-sram-pm.S

@@ -27,6 +27,7 @@
 #define EMIF_POWER_MGMT_SELF_REFRESH_MODE_MASK		0x0700
 
 #define EMIF_SDCFG_TYPE_DDR2				0x2 << SDRAM_TYPE_SHIFT
+#define EMIF_SDCFG_TYPE_DDR3				0x3 << SDRAM_TYPE_SHIFT
 #define EMIF_STATUS_READY				0x4
 
 #define AM43XX_EMIF_PHY_CTRL_REG_COUNT                  0x120
@@ -244,6 +245,46 @@ emif_skip_restore_extra_regs:
 	mov	pc, lr
 ENDPROC(ti_emif_restore_context)
 
+/*
+ * void ti_emif_run_hw_leveling(void)
+ *
+ * Used during resume to run hardware leveling again and restore the
+ * configuration of the EMIF PHY, only for DDR3.
+ */
+ENTRY(ti_emif_run_hw_leveling)
+	adr	r4, ti_emif_pm_sram_data
+	ldr	r0, [r4, #EMIF_PM_BASE_ADDR_PHYS_OFFSET]
+
+	ldr	r3, [r0, #EMIF_READ_WRITE_LEVELING_CONTROL]
+	orr	r3, r3, #RDWRLVLFULL_START
+	ldr	r2, [r0, #EMIF_SDRAM_CONFIG]
+	and	r2, r2, #SDRAM_TYPE_MASK
+	cmp	r2, #EMIF_SDCFG_TYPE_DDR3
+	bne	skip_hwlvl
+
+	str	r3, [r0, #EMIF_READ_WRITE_LEVELING_CONTROL]
+
+	/*
+	 * If EMIF registers are touched during initial stage of HW
+	 * leveling sequence there will be an L3 NOC timeout error issued
+	 * as the EMIF will not respond, which is not fatal, but it is
+	 * avoidable. This small wait loop is enough time for this condition
+	 * to clear, even at worst case of CPU running at max speed of 1Ghz.
+	 */
+	mov	r2, #0x2000
+1:
+	subs	r2, r2, #0x1
+	bne	1b
+
+	/* Bit clears when operation is complete */
+2:	ldr     r1, [r0, #EMIF_READ_WRITE_LEVELING_CONTROL]
+	tst     r1, #RDWRLVLFULL_START
+	bne     2b
+
+skip_hwlvl:
+	mov	pc, lr
+ENDPROC(ti_emif_run_hw_leveling)
+
 /*
  * void ti_emif_enter_sr(void)
  *

include/linux/ti-emif-sram.h

@@ -55,6 +55,7 @@ struct ti_emif_pm_data {
 struct ti_emif_pm_functions {
 	u32 save_context;
 	u32 restore_context;
+	u32 run_hw_leveling;
 	u32 enter_sr;
 	u32 exit_sr;
 	u32 abort_sr;
@@ -126,6 +127,8 @@ static inline void ti_emif_asm_offsets(void)
 	       offsetof(struct ti_emif_pm_functions, save_context));
 	DEFINE(EMIF_PM_RESTORE_CONTEXT_OFFSET,
 	       offsetof(struct ti_emif_pm_functions, restore_context));
+	DEFINE(EMIF_PM_RUN_HW_LEVELING,
+	       offsetof(struct ti_emif_pm_functions, run_hw_leveling));
 	DEFINE(EMIF_PM_ENTER_SR_OFFSET,
 	       offsetof(struct ti_emif_pm_functions, enter_sr));
 	DEFINE(EMIF_PM_EXIT_SR_OFFSET,