Commit 35e6de38 authored by Paul Burton's avatar Paul Burton Committed by Ralf Baechle

MIPS: traps: Ensure L1 & L2 ECC checking match for CM3 systems

On systems with CM3, we must ensure that the L1 & L2 ECC enables are set
to the same value. This is presumed by the hardware & cache corruption
can occur when it is not the case. Support enabling & disabling the L2
ECC checking on CM3 systems where this is controlled via a GCR, and
ensure that it matches the state of L1 ECC checking. Remove I6400 from
the switch statement it will no longer hit, and which was incorrect
since the L2 ECC enable bit isn't in the CP0 ErrCtl register.
Signed-off-by: default avatarPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14413/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent d65e5677
......@@ -187,6 +187,7 @@ BUILD_CM_R_(config, MIPS_CM_GCB_OFS + 0x00)
BUILD_CM_RW(base, MIPS_CM_GCB_OFS + 0x08)
BUILD_CM_RW(access, MIPS_CM_GCB_OFS + 0x20)
BUILD_CM_R_(rev, MIPS_CM_GCB_OFS + 0x30)
BUILD_CM_RW(err_control, MIPS_CM_GCB_OFS + 0x38)
BUILD_CM_RW(error_mask, MIPS_CM_GCB_OFS + 0x40)
BUILD_CM_RW(error_cause, MIPS_CM_GCB_OFS + 0x48)
BUILD_CM_RW(error_addr, MIPS_CM_GCB_OFS + 0x50)
......@@ -266,6 +267,12 @@ BUILD_CM_Cx_R_(tcid_8_priority, 0x80)
#define CM_REV_CM2_5 CM_ENCODE_REV(7, 0)
#define CM_REV_CM3 CM_ENCODE_REV(8, 0)
/* GCR_ERR_CONTROL register fields */
#define CM_GCR_ERR_CONTROL_L2_ECC_EN_SHF 1
#define CM_GCR_ERR_CONTROL_L2_ECC_EN_MSK (_ULCAST_(0x1) << 1)
#define CM_GCR_ERR_CONTROL_L2_ECC_SUPPORT_SHF 0
#define CM_GCR_ERR_CONTROL_L2_ECC_SUPPORT_MSK (_ULCAST_(0x1) << 0)
/* GCR_ERROR_CAUSE register fields */
#define CM_GCR_ERROR_CAUSE_ERRTYPE_SHF 27
#define CM_GCR_ERROR_CAUSE_ERRTYPE_MSK (_ULCAST_(0x1f) << 27)
......
......@@ -51,6 +51,7 @@
#include <asm/idle.h>
#include <asm/mips-cm.h>
#include <asm/mips-r2-to-r6-emul.h>
#include <asm/mips-cm.h>
#include <asm/mipsregs.h>
#include <asm/mipsmtregs.h>
#include <asm/module.h>
......@@ -1644,6 +1645,65 @@ __setup("nol2par", nol2parity);
*/
static inline void parity_protection_init(void)
{
#define ERRCTL_PE 0x80000000
#define ERRCTL_L2P 0x00800000
if (mips_cm_revision() >= CM_REV_CM3) {
ulong gcr_ectl, cp0_ectl;
/*
* With CM3 systems we need to ensure that the L1 & L2
* parity enables are set to the same value, since this
* is presumed by the hardware engineers.
*
* If the user disabled either of L1 or L2 ECC checking,
* disable both.
*/
l1parity &= l2parity;
l2parity &= l1parity;
/* Probe L1 ECC support */
cp0_ectl = read_c0_ecc();
write_c0_ecc(cp0_ectl | ERRCTL_PE);
back_to_back_c0_hazard();
cp0_ectl = read_c0_ecc();
/* Probe L2 ECC support */
gcr_ectl = read_gcr_err_control();
if (!(gcr_ectl & CM_GCR_ERR_CONTROL_L2_ECC_SUPPORT_MSK) ||
!(cp0_ectl & ERRCTL_PE)) {
/*
* One of L1 or L2 ECC checking isn't supported,
* so we cannot enable either.
*/
l1parity = l2parity = 0;
}
/* Configure L1 ECC checking */
if (l1parity)
cp0_ectl |= ERRCTL_PE;
else
cp0_ectl &= ~ERRCTL_PE;
write_c0_ecc(cp0_ectl);
back_to_back_c0_hazard();
WARN_ON(!!(read_c0_ecc() & ERRCTL_PE) != l1parity);
/* Configure L2 ECC checking */
if (l2parity)
gcr_ectl |= CM_GCR_ERR_CONTROL_L2_ECC_EN_MSK;
else
gcr_ectl &= ~CM_GCR_ERR_CONTROL_L2_ECC_EN_MSK;
write_gcr_err_control(gcr_ectl);
gcr_ectl = read_gcr_err_control();
gcr_ectl &= CM_GCR_ERR_CONTROL_L2_ECC_EN_MSK;
WARN_ON(!!gcr_ectl != l2parity);
pr_info("Cache parity protection %sabled\n",
l1parity ? "en" : "dis");
return;
}
switch (current_cpu_type()) {
case CPU_24K:
case CPU_34K:
......@@ -1654,11 +1714,8 @@ static inline void parity_protection_init(void)
case CPU_PROAPTIV:
case CPU_P5600:
case CPU_QEMU_GENERIC:
case CPU_I6400:
case CPU_P6600:
{
#define ERRCTL_PE 0x80000000
#define ERRCTL_L2P 0x00800000
unsigned long errctl;
unsigned int l1parity_present, l2parity_present;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment