Merge tag 'renesas-r8a7778-ccf-and-multiplatform-for-v4.1' of...

Merge tag 'renesas-r8a7778-ccf-and-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform

Pull "Renesas ARM Based SoC r8a7778 CCF and Multiplatform Updates
for v4.1" from Simon Horman:

* Add CCF and them multiplatform support to r8a7778 SoC and its
  bockw board.

* tag 'renesas-r8a7778-ccf-and-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (21 commits)
  ARM: shmobile: r8a7778: enable multiplatform target
  ARM: shmobile: bockw: add sound to DT
  ARM: shmobile: r8a7778: add sound to DT
  ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
  DT: i2c: add trivial binding for OKI ML86V7667 video decoder
  ARM: shmobile: r8a7778: common clock framework CPG driver
  ARM: shmobile: bockw dts: set extal clock frequency
  ARM: shmobile: bockw dts: Move Ethernet node to BSC
  ARM: shmobile: r8a7778 dtsi: Add Bus State Controller node
  ARM: shmobile: bockw: add USB, VIN pin descriptions to DT
  ARM: shmobile: r8a7778: add internal ethernet controller to DT
  ARM: shmobile: r8a7778: add MSTP clock assignments to DT
  ARM: shmobile: r8a7778: implement SoC and board CCF support
  ARM: shmobile: r8a7778: Common clock framework DT description
  ARM: shmobile: r8a7778: add CPG register bits header
  ARM: shmobile: r8a7778: synchronize dts with reference platform
  drivers: bus: Add Simple Power-Managed Bus Driver
  drivers: bus: Add Renesas Bus State Controller (BSC) DT Bindings
  drivers: bus: Add Simple Power-Managed Bus DT Bindings
  drivers: bus: Sort Makefile entries alphabetically
  ...

Documentation/devicetree/bindings/bus/renesas,bsc.txt

+Renesas Bus State Controller (BSC)
+==================================
+
+The Renesas Bus State Controller (BSC, sometimes called "LBSC within Bus
+Bridge", or "External Bus Interface") can be found in several Renesas ARM SoCs.
+It provides an external bus for connecting multiple external devices to the
+SoC, driving several chip select lines, for e.g. NOR FLASH, Ethernet and USB.
+
+While the BSC is a fairly simple memory-mapped bus, it may be part of a PM
+domain, and may have a gateable functional clock.
+Before a device connected to the BSC can be accessed, the PM domain
+containing the BSC must be powered on, and the functional clock
+driving the BSC must be enabled.
+
+The bindings for the BSC extend the bindings for "simple-pm-bus".
+
+
+Required properties
+  - compatible: Must contain an SoC-specific value, and "renesas,bsc" and
+		"simple-pm-bus" as fallbacks.
+                SoC-specific values can be:
+		"renesas,bsc-r8a73a4" for R-Mobile APE6 (r8a73a4)
+		"renesas,bsc-sh73a0" for SH-Mobile AG5 (sh73a0)
+  - #address-cells, #size-cells, ranges: Must describe the mapping between
+		parent address and child address spaces.
+  - reg: Must contain the base address and length to access the bus controller.
+
+Optional properties:
+  - interrupts: Must contain a reference to the BSC interrupt, if available.
+  - clocks: Must contain a reference to the functional clock, if available.
+  - power-domains: Must contain a reference to the PM domain, if available.
+
+
+Example:
+
+	bsc: bus@fec10000 {
+		compatible = "renesas,bsc-sh73a0", "renesas,bsc",
+			     "simple-pm-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0x20000000>;
+		reg = <0xfec10000 0x400>;
+		interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&zb_clk>;
+		power-domains = <&pd_a4s>;
+	};

Documentation/devicetree/bindings/bus/simple-pm-bus.txt

+Simple Power-Managed Bus
+========================
+
+A Simple Power-Managed Bus is a transparent bus that doesn't need a real
+driver, as it's typically initialized by the boot loader.
+
+However, its bus controller is part of a PM domain, or under the control of a
+functional clock.  Hence, the bus controller's PM domain and/or clock must be
+enabled for child devices connected to the bus (either on-SoC or externally)
+to function.
+
+While "simple-pm-bus" follows the "simple-bus" set of properties, as specified
+in ePAPR, it is not an extension of "simple-bus".
+
+
+Required properties:
+  - compatible: Must contain at least "simple-pm-bus".
+		Must not contain "simple-bus".
+		It's recommended to let this be preceded by one or more
+		vendor-specific compatible values.
+  - #address-cells, #size-cells, ranges: Must describe the mapping between
+		parent address and child address spaces.
+
+Optional platform-specific properties for clock or PM domain control (at least
+one of them is required):
+  - clocks: Must contain a reference to the functional clock(s),
+  - power-domains: Must contain a reference to the PM domain.
+Please refer to the binding documentation for the clock and/or PM domain
+providers for more details.
+
+
+Example:
+
+	bsc: bus@fec10000 {
+		compatible = "renesas,bsc-sh73a0", "renesas,bsc",
+			     "simple-pm-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0x20000000>;
+		reg = <0xfec10000 0x400>;
+		interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&zb_clk>;
+		power-domains = <&pd_a4s>;
+	};

Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt

+* Renesas R8A7778 Clock Pulse Generator (CPG)
+
+The CPG generates core clocks for the R8A7778. It includes two PLLs and
+several fixed ratio dividers
+
+Required Properties:
+
+  - compatible: Must be "renesas,r8a7778-cpg-clocks"
+  - reg: Base address and length of the memory resource used by the CPG
+  - #clock-cells: Must be 1
+  - clock-output-names: The names of the clocks. Supported clocks are
+    "plla", "pllb", "b", "out", "p", "s", and "s1".
+
+
+Example
+-------
+
+	cpg_clocks: cpg_clocks@ffc80000 {
+		compatible = "renesas,r8a7778-cpg-clocks";
+		reg = <0xffc80000 0x80>;
+		#clock-cells = <1>;
+		clocks = <&extal_clk>;
+		clock-output-names = "plla", "pllb", "b",
+				     "out", "p", "s", "s1";
+	};

Documentation/devicetree/bindings/i2c/trivial-devices.txt

@@ -77,6 +77,7 @@ nxp,pca9556		Octal SMBus and I2C registered interface
 nxp,pca9557		8-bit I2C-bus and SMBus I/O port with reset
 nxp,pcf8563		Real-time clock/calendar
 nxp,pcf85063		Tiny Real-Time Clock
+oki,ml86v7667		OKI ML86V7667 video decoder
 ovti,ov5642		OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus
 pericom,pt7c4338	Real-time Clock Module
 plx,pex8648		48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch

arch/arm/boot/dts/Makefile

@@ -477,6 +477,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
 	r7s72100-genmai.dtb \
 	r8a73a4-ape6evm.dtb \
 	r8a7740-armadillo800eva.dtb \
+	r8a7778-bockw.dtb \
 	r8a7779-marzen.dtb \
 	r8a7790-lager.dtb \
 	r8a7791-henninger.dtb \

arch/arm/boot/dts/r8a7778-bockw.dts

@@ -16,17 +16,191 @@
 
 /dts-v1/;
 #include "r8a7778.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "bockw";
 	compatible = "renesas,bockw", "renesas,r8a7778";
 
+	aliases {
+		serial0 = &scif0;
+	};
+
 	chosen {
 		bootargs = "console=ttySC0,115200 ignore_loglevel ip=dhcp root=/dev/nfs rw";
+		stdout-path = &scif0;
 	};
 
 	memory {
 		device_type = "memory";
 		reg = <0x60000000 0x10000000>;
 	};
+
+	fixedregulator3v3: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcodec>;
+		simple-audio-card,frame-master = <&sndcodec>;
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&ak4643>;
+			system-clock-frequency = <11289600>;
+		};
+	};
+};
+
+&bsc {
+	ethernet@18300000 {
+		compatible = "smsc,lan9220", "smsc,lan9115";
+		reg = <0x18300000 0x1000>;
+
+		phy-mode = "mii";
+		interrupt-parent = <&irqpin>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		reg-io-width = <4>;
+		vddvario-supply = <&fixedregulator3v3>;
+		vdd33a-supply = <&fixedregulator3v3>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <33333333>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	ak4643: sound-codec@12 {
+		compatible = "asahi-kasei,ak4643";
+		#sound-dai-cells = <0>;
+		reg = <0x12>;
+	};
+
+	camera@41 {
+		compatible = "oki,ml86v7667";
+		reg = <0x41>;
+	};
+
+	camera@43 {
+		compatible = "oki,ml86v7667";
+		reg = <0x43>;
+	};
+
+	rx8581: rtc@51 {
+		compatible = "epson,rx8581";
+		reg = <0x51>;
+	};
+};
+
+&mmcif {
+	pinctrl-0 = <&mmc_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&fixedregulator3v3>;
+	bus-width = <8>;
+	broken-cd;
+	status = "okay";
+};
+
+&irqpin {
+	status = "okay";
+};
+
+&tmu0 {
+	status = "okay";
+};
+
+&pfc {
+	scif0_pins: serial0 {
+		renesas,groups = "scif0_data_a", "scif0_ctrl";
+		renesas,function = "scif0";
+	};
+
+	mmc_pins: mmc {
+		renesas,groups = "mmc_data8", "mmc_ctrl";
+		renesas,function = "mmc";
+	};
+
+	sdhi0_pins: sd0 {
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl",
+				  "sdhi0_cd";
+		renesas,function = "sdhi0";
+	};
+
+	hspi0_pins: hspi0 {
+		renesas,groups = "hspi0_a";
+		renesas,function = "hspi0";
+	};
+
+	usb0_pins: usb0 {
+		renesas,groups = "usb0";
+		renesas,function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		renesas,groups = "usb1";
+		renesas,function = "usb1";
+	};
+
+	vin0_pins: vin0 {
+		renesas,groups = "vin0_data8", "vin0_clk";
+		renesas,function = "vin0";
+	};
+
+	vin1_pins: vin1 {
+		renesas,groups = "vin1_data8", "vin1_clk";
+		renesas,function = "vin1";
+	};
+};
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&fixedregulator3v3>;
+	bus-width = <4>;
+	status = "okay";
+	wp-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
+};
+
+&hspi0 {
+	pinctrl-0 = <&hspi0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spansion,s25fl008k";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		m25p,fast-read;
+
+		partition@0 {
+			label = "data(spi)";
+			reg = <0x00000000 0x00100000>;
+		};
+	};
+};
+
+&scif0 {
+	pinctrl-0 = <&scif0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
 };

arch/arm/mach-shmobile/Kconfig

@@ -62,6 +62,10 @@ config ARCH_R8A7740
 	select ARCH_RMOBILE
 	select RENESAS_INTC_IRQPIN
 
+config ARCH_R8A7778
+	bool "R-Car M1A (R8A77781)"
+	select ARCH_RCAR_GEN1
+
 config ARCH_R8A7779
 	bool "R-Car H1 (R8A77790)"
 	select ARCH_RCAR_GEN1

arch/arm/mach-shmobile/board-bockw-reference.c

@@ -36,7 +36,9 @@ static void __init bockw_init(void)
 	void __iomem *fpga;
 	void __iomem *pfc;
 
+#ifndef CONFIG_COMMON_CLK
 	r8a7778_clock_init();
+#endif
 	r8a7778_init_irq_extpin_dt(1);
 	r8a7778_add_dt_devices();
 

arch/arm/mach-shmobile/setup-r8a7778.c

@@ -15,6 +15,7 @@
  * GNU General Public License for more details.
  */
 
+#include <linux/clk/shmobile.h>
 #include <linux/kernel.h>
 #include <linux/io.h>
 #include <linux/irqchip/arm-gic.h>
@@ -41,6 +42,21 @@
 #include "irqs.h"
 #include "r8a7778.h"
 
+#define MODEMR 0xffcc0020
+
+#ifdef CONFIG_COMMON_CLK
+static void __init r8a7778_timer_init(void)
+{
+	u32 mode;
+	void __iomem *modemr = ioremap_nocache(MODEMR, 4);
+
+	BUG_ON(!modemr);
+	mode = ioread32(modemr);
+	iounmap(modemr);
+	r8a7778_clocks_init(mode);
+}
+#endif
+
 /* SCIF */
 #define R8A7778_SCIF(index, baseaddr, irq)			\
 static struct plat_sci_port scif##index##_platform_data = {	\
@@ -608,6 +624,9 @@ DT_MACHINE_START(R8A7778_DT, "Generic R8A7778 (Flattened Device Tree)")
 	.init_early	= shmobile_init_delay,
 	.init_irq	= r8a7778_init_irq_dt,
 	.init_late	= shmobile_init_late,
+#ifdef CONFIG_COMMON_CLK
+	.init_time	= r8a7778_timer_init,
+#endif
 	.dt_compat	= r8a7778_compat_dt,
 MACHINE_END
 

drivers/bus/Kconfig

@@ -4,6 +4,21 @@
 
 menu "Bus devices"
 
+config ARM_CCI
+	bool "ARM CCI driver support"
+	depends on ARM && OF && CPU_V7
+	help
+	  Driver supporting the CCI cache coherent interconnect for ARM
+	  platforms.
+
+config ARM_CCN
+	bool "ARM CCN driver support"
+	depends on ARM || ARM64
+	depends on PERF_EVENTS
+	help
+	  PMU (perf) driver supporting the ARM CCN (Cache Coherent Network)
+	  interconnect.
+
 config BRCMSTB_GISB_ARB
 	bool "Broadcom STB GISB bus arbiter"
 	depends on ARM || MIPS
@@ -27,15 +42,6 @@ config MVEBU_MBUS
 	  Driver needed for the MBus configuration on Marvell EBU SoCs
 	  (Kirkwood, Dove, Orion5x, MV78XX0 and Armada 370/XP).
 
-config OMAP_OCP2SCP
-	tristate "OMAP OCP2SCP DRIVER"
-	depends on ARCH_OMAP2PLUS
-	help
-	  Driver to enable ocp2scp module which transforms ocp interface
-	  protocol to scp protocol. In OMAP4, USB PHY is connected via
-	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
-	  OCP2SCP.
-
 config OMAP_INTERCONNECT
 	tristate "OMAP INTERCONNECT DRIVER"
 	depends on ARCH_OMAP2PLUS
@@ -43,20 +49,27 @@ config OMAP_INTERCONNECT
 	help
 	  Driver to enable OMAP interconnect error handling driver.
 
-config ARM_CCI
-	bool "ARM CCI driver support"
-	depends on ARM && OF && CPU_V7
+config OMAP_OCP2SCP
+	tristate "OMAP OCP2SCP DRIVER"
+	depends on ARCH_OMAP2PLUS
 	help
-	  Driver supporting the CCI cache coherent interconnect for ARM
-	  platforms.
+	  Driver to enable ocp2scp module which transforms ocp interface
+	  protocol to scp protocol. In OMAP4, USB PHY is connected via
+	  OCP2SCP and in OMAP5, both USB PHY and SATA PHY is connected via
+	  OCP2SCP.
 
-config ARM_CCN
-	bool "ARM CCN driver support"
-	depends on ARM || ARM64
-	depends on PERF_EVENTS
+config SIMPLE_PM_BUS
+	bool "Simple Power-Managed Bus Driver"
+	depends on OF && PM
+	depends on ARCH_SHMOBILE || COMPILE_TEST
 	help
-	  PMU (perf) driver supporting the ARM CCN (Cache Coherent Network)
-	  interconnect.
+	  Driver for transparent busses that don't need a real driver, but
+	  where the bus controller is part of a PM domain, or under the control
+	  of a functional clock, and thus relies on runtime PM for managing
+	  this PM domain and/or clock.
+	  An example of such a bus controller is the Renesas Bus State
+	  Controller (BSC, sometimes called "LBSC within Bus Bridge", or
+	  "External Bus Interface") as found on several Renesas ARM SoCs.
 
 config VEXPRESS_CONFIG
 	bool "Versatile Express configuration bus"

drivers/bus/Makefile

@@ -2,16 +2,17 @@
 # Makefile for the bus drivers.
 #
 
+# Interconnect bus drivers for ARM platforms
+obj-$(CONFIG_ARM_CCI)		+= arm-cci.o
+obj-$(CONFIG_ARM_CCN)		+= arm-ccn.o
+
 obj-$(CONFIG_BRCMSTB_GISB_ARB)	+= brcmstb_gisb.o
-obj-$(CONFIG_IMX_WEIM)	+= imx-weim.o
-obj-$(CONFIG_MVEBU_MBUS) += mvebu-mbus.o
-obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
+obj-$(CONFIG_IMX_WEIM)		+= imx-weim.o
+obj-$(CONFIG_MVEBU_MBUS) 	+= mvebu-mbus.o
 
 # Interconnect bus driver for OMAP SoCs.
 obj-$(CONFIG_OMAP_INTERCONNECT)	+= omap_l3_smx.o omap_l3_noc.o
 
-# Interconnect bus drivers for ARM platforms
-obj-$(CONFIG_ARM_CCI)		+= arm-cci.o
-obj-$(CONFIG_ARM_CCN)		+= arm-ccn.o
-
+obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
+obj-$(CONFIG_SIMPLE_PM_BUS)	+= simple-pm-bus.o
 obj-$(CONFIG_VEXPRESS_CONFIG)	+= vexpress-config.o

drivers/bus/simple-pm-bus.c

+/*
+ * Simple Power-Managed Bus Driver
+ *
+ * Copyright (C) 2014-2015 Glider bvba
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+
+static int simple_pm_bus_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+
+	dev_dbg(&pdev->dev, "%s\n", __func__);
+
+	pm_runtime_enable(&pdev->dev);
+
+	if (np)
+		of_platform_populate(np, NULL, NULL, &pdev->dev);
+
+	return 0;
+}
+
+static int simple_pm_bus_remove(struct platform_device *pdev)
+{
+	dev_dbg(&pdev->dev, "%s\n", __func__);
+
+	pm_runtime_disable(&pdev->dev);
+	return 0;
+}
+
+static const struct of_device_id simple_pm_bus_of_match[] = {
+	{ .compatible = "simple-pm-bus", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, simple_pm_bus_of_match);
+
+static struct platform_driver simple_pm_bus_driver = {
+	.probe = simple_pm_bus_probe,
+	.remove = simple_pm_bus_remove,
+	.driver = {
+		.name = "simple-pm-bus",
+		.of_match_table = simple_pm_bus_of_match,
+	},
+};
+
+module_platform_driver(simple_pm_bus_driver);
+
+MODULE_DESCRIPTION("Simple Power-Managed Bus Driver");
+MODULE_AUTHOR("Geert Uytterhoeven <geert+renesas@glider.be>");
+MODULE_LICENSE("GPL v2");

drivers/clk/shmobile/Makefile

@@ -2,6 +2,7 @@ obj-$(CONFIG_ARCH_EMEV2)		+= clk-emev2.o
 obj-$(CONFIG_ARCH_R7S72100)		+= clk-rz.o
 obj-$(CONFIG_ARCH_R8A73A4)		+= clk-r8a73a4.o
 obj-$(CONFIG_ARCH_R8A7740)		+= clk-r8a7740.o
+obj-$(CONFIG_ARCH_R8A7778)		+= clk-r8a7778.o
 obj-$(CONFIG_ARCH_R8A7779)		+= clk-r8a7779.o
 obj-$(CONFIG_ARCH_R8A7790)		+= clk-rcar-gen2.o
 obj-$(CONFIG_ARCH_R8A7791)		+= clk-rcar-gen2.o

drivers/clk/shmobile/clk-r8a7778.c

+/*
+ * r8a7778 Core CPG Clocks
+ *
+ * Copyright (C) 2014  Ulrich Hecht
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/clk/shmobile.h>
+#include <linux/of_address.h>
+
+struct r8a7778_cpg {
+	struct clk_onecell_data data;
+	spinlock_t lock;
+	void __iomem *reg;
+};
+
+/* PLL multipliers per bits 11, 12, and 18 of MODEMR */
+struct {
+	unsigned long plla_mult;
+	unsigned long pllb_mult;
+} r8a7778_rates[] __initdata = {
+	[0] = { 21, 21 },
+	[1] = { 24, 24 },
+	[2] = { 28, 28 },
+	[3] = { 32, 32 },
+	[5] = { 24, 21 },
+	[6] = { 28, 21 },
+	[7] = { 32, 24 },
+};
+
+/* Clock dividers per bits 1 and 2 of MODEMR */
+struct {
+	const char *name;
+	unsigned int div[4];
+} r8a7778_divs[6] __initdata = {
+	{ "b",   { 12, 12, 16, 18 } },
+	{ "out", { 12, 12, 16, 18 } },
+	{ "p",   { 16, 12, 16, 12 } },
+	{ "s",   { 4,  3,  4,  3  } },
+	{ "s1",  { 8,  6,  8,  6  } },
+};
+
+static u32 cpg_mode_rates __initdata;
+static u32 cpg_mode_divs __initdata;
+
+static struct clk * __init
+r8a7778_cpg_register_clock(struct device_node *np, struct r8a7778_cpg *cpg,
+			     const char *name)
+{
+	if (!strcmp(name, "plla")) {
+		return clk_register_fixed_factor(NULL, "plla",
+			of_clk_get_parent_name(np, 0), 0,
+			r8a7778_rates[cpg_mode_rates].plla_mult, 1);
+	} else if (!strcmp(name, "pllb")) {
+		return clk_register_fixed_factor(NULL, "pllb",
+			of_clk_get_parent_name(np, 0), 0,
+			r8a7778_rates[cpg_mode_rates].pllb_mult, 1);
+	} else {
+		unsigned int i;
+
+		for (i = 0; i < ARRAY_SIZE(r8a7778_divs); i++) {
+			if (!strcmp(name, r8a7778_divs[i].name)) {
+				return clk_register_fixed_factor(NULL,
+					r8a7778_divs[i].name,
+					"plla", 0, 1,
+					r8a7778_divs[i].div[cpg_mode_divs]);
+			}
+		}
+	}
+
+	return ERR_PTR(-EINVAL);
+}
+
+
+static void __init r8a7778_cpg_clocks_init(struct device_node *np)
+{
+	struct r8a7778_cpg *cpg;
+	struct clk **clks;
+	unsigned int i;
+	int num_clks;
+
+	num_clks = of_property_count_strings(np, "clock-output-names");
+	if (num_clks < 0) {
+		pr_err("%s: failed to count clocks\n", __func__);
+		return;
+	}
+
+	cpg = kzalloc(sizeof(*cpg), GFP_KERNEL);
+	clks = kcalloc(num_clks, sizeof(*clks), GFP_KERNEL);
+	if (cpg == NULL || clks == NULL) {
+		/* We're leaking memory on purpose, there's no point in cleaning
+		 * up as the system won't boot anyway.
+		 */
+		return;
+	}
+
+	spin_lock_init(&cpg->lock);
+
+	cpg->data.clks = clks;
+	cpg->data.clk_num = num_clks;
+
+	cpg->reg = of_iomap(np, 0);
+	if (WARN_ON(cpg->reg == NULL))
+		return;
+
+	for (i = 0; i < num_clks; ++i) {
+		const char *name;
+		struct clk *clk;
+
+		of_property_read_string_index(np, "clock-output-names", i,
+					      &name);
+
+		clk = r8a7778_cpg_register_clock(np, cpg, name);
+		if (IS_ERR(clk))
+			pr_err("%s: failed to register %s %s clock (%ld)\n",
+			       __func__, np->name, name, PTR_ERR(clk));
+		else
+			cpg->data.clks[i] = clk;
+	}
+
+	of_clk_add_provider(np, of_clk_src_onecell_get, &cpg->data);
+}
+
+CLK_OF_DECLARE(r8a7778_cpg_clks, "renesas,r8a7778-cpg-clocks",
+	       r8a7778_cpg_clocks_init);
+
+void __init r8a7778_clocks_init(u32 mode)
+{
+	BUG_ON(!(mode & BIT(19)));
+
+	cpg_mode_rates = (!!(mode & BIT(18)) << 2) |
+			 (!!(mode & BIT(12)) << 1) |
+			 (!!(mode & BIT(11)));
+	cpg_mode_divs = (!!(mode & BIT(2)) << 1) |
+			(!!(mode & BIT(1)));
+
+	of_clk_init(NULL);
+}

include/dt-bindings/clock/r8a7778-clock.h

+/*
+ * Copyright (C) 2014 Ulrich Hecht
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_R8A7778_H__
+#define __DT_BINDINGS_CLOCK_R8A7778_H__
+
+/* CPG */
+#define R8A7778_CLK_PLLA	0
+#define R8A7778_CLK_PLLB	1
+#define R8A7778_CLK_B		2
+#define R8A7778_CLK_OUT		3
+#define R8A7778_CLK_P		4
+#define R8A7778_CLK_S		5
+#define R8A7778_CLK_S1		6
+
+/* MSTP0 */
+#define R8A7778_CLK_I2C0	30
+#define R8A7778_CLK_I2C1	29
+#define R8A7778_CLK_I2C2	28
+#define R8A7778_CLK_I2C3	27
+#define R8A7778_CLK_SCIF0	26
+#define R8A7778_CLK_SCIF1	25
+#define R8A7778_CLK_SCIF2	24
+#define R8A7778_CLK_SCIF3	23
+#define R8A7778_CLK_SCIF4	22
+#define R8A7778_CLK_SCIF5	21
+#define R8A7778_CLK_TMU0	16
+#define R8A7778_CLK_TMU1	15
+#define R8A7778_CLK_TMU2	14
+#define R8A7778_CLK_SSI0	12
+#define R8A7778_CLK_SSI1	11
+#define R8A7778_CLK_SSI2	10
+#define R8A7778_CLK_SSI3	9
+#define R8A7778_CLK_SRU		8
+#define R8A7778_CLK_HSPI	7
+
+/* MSTP1 */
+#define R8A7778_CLK_ETHER	14
+#define R8A7778_CLK_VIN0	10
+#define R8A7778_CLK_VIN1	9
+#define R8A7778_CLK_USB		0
+
+/* MSTP3 */
+#define R8A7778_CLK_MMC		31
+#define R8A7778_CLK_SDHI0	23
+#define R8A7778_CLK_SDHI1	22
+#define R8A7778_CLK_SDHI2	21
+#define R8A7778_CLK_SSI4	11
+#define R8A7778_CLK_SSI5	10
+#define R8A7778_CLK_SSI6	9
+#define R8A7778_CLK_SSI7	8
+#define R8A7778_CLK_SSI8	7
+
+/* MSTP5 */
+#define R8A7778_CLK_SRU_SRC0	31
+#define R8A7778_CLK_SRU_SRC1	30
+#define R8A7778_CLK_SRU_SRC2	29
+#define R8A7778_CLK_SRU_SRC3	28
+#define R8A7778_CLK_SRU_SRC4	27
+#define R8A7778_CLK_SRU_SRC5	26
+#define R8A7778_CLK_SRU_SRC6	25
+#define R8A7778_CLK_SRU_SRC7	24
+#define R8A7778_CLK_SRU_SRC8	23
+
+#endif /* __DT_BINDINGS_CLOCK_R8A7778_H__ */

include/linux/clk/shmobile.h

@@ -16,6 +16,7 @@
 
 #include <linux/types.h>
 
+void r8a7778_clocks_init(u32 mode);
 void r8a7779_clocks_init(u32 mode);
 void rcar_gen2_clocks_init(u32 mode);