Commit 3b12308f authored by Sergey Ryazanov's avatar Sergey Ryazanov Committed by Ralf Baechle

MIPS: ath25: add basic AR5312 SoC support

Add basic support for Atheros AR5312/AR2312 SoCs: registers definition
file and initial setup code.
Signed-off-by: default avatarSergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8238/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent 43cc739f
......@@ -877,6 +877,7 @@ config MIPS_PARAVIRT
endchoice
source "arch/mips/alchemy/Kconfig"
source "arch/mips/ath25/Kconfig"
source "arch/mips/ath79/Kconfig"
source "arch/mips/bcm47xx/Kconfig"
source "arch/mips/bcm63xx/Kconfig"
......
config SOC_AR5312
bool "Atheros AR5312/AR2312+ SoC support"
depends on ATH25
default y
......@@ -9,3 +9,5 @@
#
obj-y += board.o prom.o devices.o
obj-$(CONFIG_SOC_AR5312) += ar5312.o
/*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
* Copyright (C) 2006 FON Technology, SL.
* Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
* Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
* Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
*/
/*
* Platform devices for Atheros AR5312 SoCs
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/reboot.h>
#include <asm/bootinfo.h>
#include <asm/reboot.h>
#include <asm/time.h>
#include "devices.h"
#include "ar5312.h"
#include "ar5312_regs.h"
static void __iomem *ar5312_rst_base;
static inline u32 ar5312_rst_reg_read(u32 reg)
{
return __raw_readl(ar5312_rst_base + reg);
}
static inline void ar5312_rst_reg_write(u32 reg, u32 val)
{
__raw_writel(val, ar5312_rst_base + reg);
}
static inline void ar5312_rst_reg_mask(u32 reg, u32 mask, u32 val)
{
u32 ret = ar5312_rst_reg_read(reg);
ret &= ~mask;
ret |= val;
ar5312_rst_reg_write(reg, ret);
}
static void ar5312_restart(char *command)
{
/* reset the system */
local_irq_disable();
while (1)
ar5312_rst_reg_write(AR5312_RESET, AR5312_RESET_SYSTEM);
}
/*
* This table is indexed by bits 5..4 of the CLOCKCTL1 register
* to determine the predevisor value.
*/
static unsigned clockctl1_predivide_table[4] __initdata = { 1, 2, 4, 5 };
static unsigned __init ar5312_cpu_frequency(void)
{
u32 scratch, devid, clock_ctl1;
u32 predivide_mask, multiplier_mask, doubler_mask;
unsigned predivide_shift, multiplier_shift;
unsigned predivide_select, predivisor, multiplier;
/* Trust the bootrom's idea of cpu frequency. */
scratch = ar5312_rst_reg_read(AR5312_SCRATCH);
if (scratch)
return scratch;
devid = ar5312_rst_reg_read(AR5312_REV);
devid = (devid & AR5312_REV_MAJ) >> AR5312_REV_MAJ_S;
if (devid == AR5312_REV_MAJ_AR2313) {
predivide_mask = AR2313_CLOCKCTL1_PREDIVIDE_MASK;
predivide_shift = AR2313_CLOCKCTL1_PREDIVIDE_SHIFT;
multiplier_mask = AR2313_CLOCKCTL1_MULTIPLIER_MASK;
multiplier_shift = AR2313_CLOCKCTL1_MULTIPLIER_SHIFT;
doubler_mask = AR2313_CLOCKCTL1_DOUBLER_MASK;
} else { /* AR5312 and AR2312 */
predivide_mask = AR5312_CLOCKCTL1_PREDIVIDE_MASK;
predivide_shift = AR5312_CLOCKCTL1_PREDIVIDE_SHIFT;
multiplier_mask = AR5312_CLOCKCTL1_MULTIPLIER_MASK;
multiplier_shift = AR5312_CLOCKCTL1_MULTIPLIER_SHIFT;
doubler_mask = AR5312_CLOCKCTL1_DOUBLER_MASK;
}
/*
* Clocking is derived from a fixed 40MHz input clock.
*
* cpu_freq = input_clock * MULT (where MULT is PLL multiplier)
* sys_freq = cpu_freq / 4 (used for APB clock, serial,
* flash, Timer, Watchdog Timer)
*
* cnt_freq = cpu_freq / 2 (use for CPU count/compare)
*
* So, for example, with a PLL multiplier of 5, we have
*
* cpu_freq = 200MHz
* sys_freq = 50MHz
* cnt_freq = 100MHz
*
* We compute the CPU frequency, based on PLL settings.
*/
clock_ctl1 = ar5312_rst_reg_read(AR5312_CLOCKCTL1);
predivide_select = (clock_ctl1 & predivide_mask) >> predivide_shift;
predivisor = clockctl1_predivide_table[predivide_select];
multiplier = (clock_ctl1 & multiplier_mask) >> multiplier_shift;
if (clock_ctl1 & doubler_mask)
multiplier <<= 1;
return (40000000 / predivisor) * multiplier;
}
static inline unsigned ar5312_sys_frequency(void)
{
return ar5312_cpu_frequency() / 4;
}
void __init ar5312_plat_time_init(void)
{
mips_hpt_frequency = ar5312_cpu_frequency() / 2;
}
void __init ar5312_plat_mem_setup(void)
{
void __iomem *sdram_base;
u32 memsize, memcfg, bank0_ac, bank1_ac;
/* Detect memory size */
sdram_base = ioremap_nocache(AR5312_SDRAMCTL_BASE,
AR5312_SDRAMCTL_SIZE);
memcfg = __raw_readl(sdram_base + AR5312_MEM_CFG1);
bank0_ac = ATH25_REG_MS(memcfg, AR5312_MEM_CFG1_AC0);
bank1_ac = ATH25_REG_MS(memcfg, AR5312_MEM_CFG1_AC1);
memsize = (bank0_ac ? (1 << (bank0_ac + 1)) : 0) +
(bank1_ac ? (1 << (bank1_ac + 1)) : 0);
memsize <<= 20;
add_memory_region(0, memsize, BOOT_MEM_RAM);
iounmap(sdram_base);
ar5312_rst_base = ioremap_nocache(AR5312_RST_BASE, AR5312_RST_SIZE);
/* Clear any lingering AHB errors */
ar5312_rst_reg_read(AR5312_PROCADDR);
ar5312_rst_reg_read(AR5312_DMAADDR);
ar5312_rst_reg_write(AR5312_WDT_CTRL, AR5312_WDT_CTRL_IGNORE);
_machine_restart = ar5312_restart;
}
#ifndef __AR5312_H
#define __AR5312_H
#ifdef CONFIG_SOC_AR5312
void ar5312_plat_time_init(void);
void ar5312_plat_mem_setup(void);
#else
static inline void ar5312_plat_time_init(void) {}
static inline void ar5312_plat_mem_setup(void) {}
#endif
#endif /* __AR5312_H */
/*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
* Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
* Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
* Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
*/
#ifndef __ASM_MACH_ATH25_AR5312_REGS_H
#define __ASM_MACH_ATH25_AR5312_REGS_H
/*
* Address Map
*
* The AR5312 supports 2 enet MACS, even though many reference boards only
* actually use 1 of them (i.e. Only MAC 0 is actually connected to an enet
* PHY or PHY switch. The AR2312 supports 1 enet MAC.
*/
#define AR5312_WLAN0_BASE 0x18000000
#define AR5312_ENET0_BASE 0x18100000
#define AR5312_ENET1_BASE 0x18200000
#define AR5312_SDRAMCTL_BASE 0x18300000
#define AR5312_SDRAMCTL_SIZE 0x00000010
#define AR5312_FLASHCTL_BASE 0x18400000
#define AR5312_FLASHCTL_SIZE 0x00000010
#define AR5312_WLAN1_BASE 0x18500000
#define AR5312_UART0_BASE 0x1c000000 /* UART MMR */
#define AR5312_GPIO_BASE 0x1c002000
#define AR5312_GPIO_SIZE 0x00000010
#define AR5312_RST_BASE 0x1c003000
#define AR5312_RST_SIZE 0x00000100
#define AR5312_FLASH_BASE 0x1e000000
#define AR5312_FLASH_SIZE 0x00800000
/*
* Need these defines to determine true number of ethernet MACs
*/
#define AR5312_AR5312_REV2 0x0052 /* AR5312 WMAC (AP31) */
#define AR5312_AR5312_REV7 0x0057 /* AR5312 WMAC (AP30-040) */
#define AR5312_AR2313_REV8 0x0058 /* AR2313 WMAC (AP43-030) */
/* Reset/Timer Block Address Map */
#define AR5312_TIMER 0x0000 /* countdown timer */
#define AR5312_RELOAD 0x0004 /* timer reload value */
#define AR5312_WDT_CTRL 0x0008 /* watchdog cntrl */
#define AR5312_WDT_TIMER 0x000c /* watchdog timer */
#define AR5312_ISR 0x0010 /* Intr Status Reg */
#define AR5312_IMR 0x0014 /* Intr Mask Reg */
#define AR5312_RESET 0x0020
#define AR5312_CLOCKCTL1 0x0064
#define AR5312_SCRATCH 0x006c
#define AR5312_PROCADDR 0x0070
#define AR5312_PROC1 0x0074
#define AR5312_DMAADDR 0x0078
#define AR5312_DMA1 0x007c
#define AR5312_ENABLE 0x0080 /* interface enb */
#define AR5312_REV 0x0090 /* revision */
/* AR5312_WDT_CTRL register bit field definitions */
#define AR5312_WDT_CTRL_IGNORE 0x00000000 /* ignore expiration */
#define AR5312_WDT_CTRL_NMI 0x00000001
#define AR5312_WDT_CTRL_RESET 0x00000002
/* AR5312_ISR register bit field definitions */
#define AR5312_ISR_TIMER 0x00000001
#define AR5312_ISR_AHBPROC 0x00000002
#define AR5312_ISR_AHBDMA 0x00000004
#define AR5312_ISR_GPIO 0x00000008
#define AR5312_ISR_UART0 0x00000010
#define AR5312_ISR_UART0DMA 0x00000020
#define AR5312_ISR_WD 0x00000040
#define AR5312_ISR_LOCAL 0x00000080
/* AR5312_RESET register bit field definitions */
#define AR5312_RESET_SYSTEM 0x00000001 /* cold reset full system */
#define AR5312_RESET_PROC 0x00000002 /* cold reset MIPS core */
#define AR5312_RESET_WLAN0 0x00000004 /* cold reset WLAN MAC/BB */
#define AR5312_RESET_EPHY0 0x00000008 /* cold reset ENET0 phy */
#define AR5312_RESET_EPHY1 0x00000010 /* cold reset ENET1 phy */
#define AR5312_RESET_ENET0 0x00000020 /* cold reset ENET0 MAC */
#define AR5312_RESET_ENET1 0x00000040 /* cold reset ENET1 MAC */
#define AR5312_RESET_UART0 0x00000100 /* cold reset UART0 */
#define AR5312_RESET_WLAN1 0x00000200 /* cold reset WLAN MAC/BB */
#define AR5312_RESET_APB 0x00000400 /* cold reset APB ar5312 */
#define AR5312_RESET_WARM_PROC 0x00001000 /* warm reset MIPS core */
#define AR5312_RESET_WARM_WLAN0_MAC 0x00002000 /* warm reset WLAN0 MAC */
#define AR5312_RESET_WARM_WLAN0_BB 0x00004000 /* warm reset WLAN0 BB */
#define AR5312_RESET_NMI 0x00010000 /* send an NMI to the CPU */
#define AR5312_RESET_WARM_WLAN1_MAC 0x00020000 /* warm reset WLAN1 MAC */
#define AR5312_RESET_WARM_WLAN1_BB 0x00040000 /* warm reset WLAN1 BB */
#define AR5312_RESET_LOCAL_BUS 0x00080000 /* reset local bus */
#define AR5312_RESET_WDOG 0x00100000 /* last reset was a wdt */
#define AR5312_RESET_WMAC0_BITS (AR5312_RESET_WLAN0 |\
AR5312_RESET_WARM_WLAN0_MAC |\
AR5312_RESET_WARM_WLAN0_BB)
#define AR5312_RESET_WMAC1_BITS (AR5312_RESET_WLAN1 |\
AR5312_RESET_WARM_WLAN1_MAC |\
AR5312_RESET_WARM_WLAN1_BB)
/* AR5312_CLOCKCTL1 register bit field definitions */
#define AR5312_CLOCKCTL1_PREDIVIDE_MASK 0x00000030
#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT 4
#define AR5312_CLOCKCTL1_MULTIPLIER_MASK 0x00001f00
#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT 8
#define AR5312_CLOCKCTL1_DOUBLER_MASK 0x00010000
/* Valid for AR5312 and AR2312 */
#define AR5312_CLOCKCTL1_PREDIVIDE_MASK 0x00000030
#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT 4
#define AR5312_CLOCKCTL1_MULTIPLIER_MASK 0x00001f00
#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT 8
#define AR5312_CLOCKCTL1_DOUBLER_MASK 0x00010000
/* Valid for AR2313 */
#define AR2313_CLOCKCTL1_PREDIVIDE_MASK 0x00003000
#define AR2313_CLOCKCTL1_PREDIVIDE_SHIFT 12
#define AR2313_CLOCKCTL1_MULTIPLIER_MASK 0x001f0000
#define AR2313_CLOCKCTL1_MULTIPLIER_SHIFT 16
#define AR2313_CLOCKCTL1_DOUBLER_MASK 0x00000000
/* AR5312_ENABLE register bit field definitions */
#define AR5312_ENABLE_WLAN0 0x00000001
#define AR5312_ENABLE_ENET0 0x00000002
#define AR5312_ENABLE_ENET1 0x00000004
#define AR5312_ENABLE_UART_AND_WLAN1_PIO 0x00000008/* UART & WLAN1 PIO */
#define AR5312_ENABLE_WLAN1_DMA 0x00000010/* WLAN1 DMAs */
#define AR5312_ENABLE_WLAN1 (AR5312_ENABLE_UART_AND_WLAN1_PIO |\
AR5312_ENABLE_WLAN1_DMA)
/* AR5312_REV register bit field definitions */
#define AR5312_REV_WMAC_MAJ 0x0000f000
#define AR5312_REV_WMAC_MAJ_S 12
#define AR5312_REV_WMAC_MIN 0x00000f00
#define AR5312_REV_WMAC_MIN_S 8
#define AR5312_REV_MAJ 0x000000f0
#define AR5312_REV_MAJ_S 4
#define AR5312_REV_MIN 0x0000000f
#define AR5312_REV_MIN_S 0
#define AR5312_REV_CHIP (AR5312_REV_MAJ|AR5312_REV_MIN)
/* Major revision numbers, bits 7..4 of Revision ID register */
#define AR5312_REV_MAJ_AR5312 0x4
#define AR5312_REV_MAJ_AR2313 0x5
/* Minor revision numbers, bits 3..0 of Revision ID register */
#define AR5312_REV_MIN_DUAL 0x0 /* Dual WLAN version */
#define AR5312_REV_MIN_SINGLE 0x1 /* Single WLAN version */
/*
* ARM Flash Controller -- 3 flash banks with either x8 or x16 devices
*/
#define AR5312_FLASHCTL0 0x0000
#define AR5312_FLASHCTL1 0x0004
#define AR5312_FLASHCTL2 0x0008
/* AR5312_FLASHCTL register bit field definitions */
#define AR5312_FLASHCTL_IDCY 0x0000000f /* Idle cycle turnaround time */
#define AR5312_FLASHCTL_IDCY_S 0
#define AR5312_FLASHCTL_WST1 0x000003e0 /* Wait state 1 */
#define AR5312_FLASHCTL_WST1_S 5
#define AR5312_FLASHCTL_RBLE 0x00000400 /* Read byte lane enable */
#define AR5312_FLASHCTL_WST2 0x0000f800 /* Wait state 2 */
#define AR5312_FLASHCTL_WST2_S 11
#define AR5312_FLASHCTL_AC 0x00070000 /* Flash addr check (added) */
#define AR5312_FLASHCTL_AC_S 16
#define AR5312_FLASHCTL_AC_128K 0x00000000
#define AR5312_FLASHCTL_AC_256K 0x00010000
#define AR5312_FLASHCTL_AC_512K 0x00020000
#define AR5312_FLASHCTL_AC_1M 0x00030000
#define AR5312_FLASHCTL_AC_2M 0x00040000
#define AR5312_FLASHCTL_AC_4M 0x00050000
#define AR5312_FLASHCTL_AC_8M 0x00060000
#define AR5312_FLASHCTL_AC_RES 0x00070000 /* 16MB is not supported */
#define AR5312_FLASHCTL_E 0x00080000 /* Flash bank enable (added) */
#define AR5312_FLASHCTL_BUSERR 0x01000000 /* Bus transfer error flag */
#define AR5312_FLASHCTL_WPERR 0x02000000 /* Write protect error flag */
#define AR5312_FLASHCTL_WP 0x04000000 /* Write protect */
#define AR5312_FLASHCTL_BM 0x08000000 /* Burst mode */
#define AR5312_FLASHCTL_MW 0x30000000 /* Mem width */
#define AR5312_FLASHCTL_MW8 0x00000000 /* Mem width x8 */
#define AR5312_FLASHCTL_MW16 0x10000000 /* Mem width x16 */
#define AR5312_FLASHCTL_MW32 0x20000000 /* Mem width x32 (not supp) */
#define AR5312_FLASHCTL_ATNR 0x00000000 /* Access == no retry */
#define AR5312_FLASHCTL_ATR 0x80000000 /* Access == retry every */
#define AR5312_FLASHCTL_ATR4 0xc0000000 /* Access == retry every 4 */
/*
* ARM SDRAM Controller -- just enough to determine memory size
*/
#define AR5312_MEM_CFG1 0x0004
#define AR5312_MEM_CFG1_AC0_M 0x00000700 /* bank 0: SDRAM addr check */
#define AR5312_MEM_CFG1_AC0_S 8
#define AR5312_MEM_CFG1_AC1_M 0x00007000 /* bank 1: SDRAM addr check */
#define AR5312_MEM_CFG1_AC1_S 12
#endif /* __ASM_MACH_ATH25_AR5312_REGS_H */
......@@ -16,6 +16,9 @@
#include <asm/bootinfo.h>
#include <asm/time.h>
#include "devices.h"
#include "ar5312.h"
static void ath25_halt(void)
{
local_irq_disable();
......@@ -27,6 +30,9 @@ void __init plat_mem_setup(void)
_machine_halt = ath25_halt;
pm_power_off = ath25_halt;
if (is_ar5312())
ar5312_plat_mem_setup();
/* Disable data watchpoints */
write_c0_watchlo0(0);
}
......@@ -37,6 +43,8 @@ asmlinkage void plat_irq_dispatch(void)
void __init plat_time_init(void)
{
if (is_ar5312())
ar5312_plat_time_init();
}
unsigned int __cpuinit get_c0_compare_int(void)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment