Commit 3b69bdbf authored by Andreas Färber's avatar Andreas Färber Committed by Kevin Hilman

arm64: dts: meson-gxbb-odroidc2: Fix node order

Sort nodes referenced by label alphabetically.
Signed-off-by: default avatarAndreas Färber <afaerber@suse.de>
Signed-off-by: default avatarKevin Hilman <khilman@baylibre.com>
parent 8d7c7711
...@@ -137,16 +137,6 @@ emmc_pwrseq: emmc-pwrseq { ...@@ -137,16 +137,6 @@ emmc_pwrseq: emmc-pwrseq {
}; };
}; };
&scpi_clocks {
status = "disabled";
};
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&ethmac { &ethmac {
status = "okay"; status = "okay";
pinctrl-0 = <&eth_rgmii_pins>; pinctrl-0 = <&eth_rgmii_pins>;
...@@ -172,6 +162,33 @@ eth_phy0: ethernet-phy@0 { ...@@ -172,6 +162,33 @@ eth_phy0: ethernet-phy@0 {
}; };
}; };
&gpio_ao {
/*
* WARNING: The USB Hub on the Odroid-C2 needs a reset signal
* to be turned high in order to be detected by the USB Controller
* This signal should be handled by a USB specific power sequence
* in order to reset the Hub when USB bus is powered down.
*/
usb-hub {
gpio-hog;
gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "usb-hub-reset";
};
};
&i2c_A {
status = "okay";
pinctrl-0 = <&i2c_a_pins>;
pinctrl-names = "default";
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&pinctrl_aobus { &pinctrl_aobus {
gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En", gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
"USB HUB nRESET", "USB OTG Power En", "USB HUB nRESET", "USB OTG Power En",
...@@ -223,55 +240,15 @@ &pinctrl_periphs { ...@@ -223,55 +240,15 @@ &pinctrl_periphs {
""; "";
}; };
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&i2c_A {
status = "okay";
pinctrl-0 = <&i2c_a_pins>;
pinctrl-names = "default";
};
&gpio_ao {
/*
* WARNING: The USB Hub on the Odroid-C2 needs a reset signal
* to be turned high in order to be detected by the USB Controller
* This signal should be handled by a USB specific power sequence
* in order to reset the Hub when USB bus is powered down.
*/
usb-hub {
gpio-hog;
gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "usb-hub-reset";
};
};
&usb0_phy {
status = "okay";
phy-supply = <&usb_otg_pwr>;
};
&usb1_phy {
status = "okay";
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};
&saradc { &saradc {
status = "okay"; status = "okay";
vref-supply = <&vcc1v8>; vref-supply = <&vcc1v8>;
}; };
&scpi_clocks {
status = "disabled";
};
/* SD */ /* SD */
&sd_emmc_b { &sd_emmc_b {
status = "okay"; status = "okay";
...@@ -309,3 +286,26 @@ &sd_emmc_c { ...@@ -309,3 +286,26 @@ &sd_emmc_c {
vmmc-supply = <&vcc3v3>; vmmc-supply = <&vcc3v3>;
vqmmc-supply = <&vcc1v8>; vqmmc-supply = <&vcc1v8>;
}; };
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&usb0_phy {
status = "okay";
phy-supply = <&usb_otg_pwr>;
};
&usb1_phy {
status = "okay";
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment