Skip to content

L
linux
Commit 3e56e354 authored by Alexander Stein's avatar Alexander Stein Committed by Shawn Guo
Browse files
Options

arm64: dts: freescale: add initial device tree for TQMa8MQNL with i.MX8MN 

This adds support for TQMa8MQNL module on MBa8Mx board.
Signed-off-by: default avatarAlexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: default avatarShawn Guo <shawnguo@kernel.org>
parent dfcd1b6f
Hide whitespace changes
Inline Side-by-side
Showing with 560 additions and 0 deletions
arch/arm64/boot/dts/freescale/Makefile
View file @ 3e56e354
......@@ -50,6 +50,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
......
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts 0 → 100644
View file @ 3e56e354
// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
/*
* Copyright 2020-2021 TQ-Systems GmbH
*/
/dts-v1/;
#include "imx8mn-tqma8mqnl.dtsi"
#include "mba8mx.dtsi"
/ {
model = "TQ-Systems GmbH i.MX8MN TQMa8MxNL on MBa8Mx";
compatible = "tq,imx8mn-tqma8mqnl-mba8mx", "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
aliases {
eeprom0 = &eeprom3;
mmc0 = &usdhc3;
mmc1 = &usdhc2;
mmc2 = &usdhc1;
rtc0 = &pcf85063;
rtc1 = &snvs_rtc;
};
reg_usdhc2_vmmc: regulator-vmmc {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
regulator-name = "VSD_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
startup-delay-us = <100>;
off-on-delay-us = <12000>;
};
};
/* Located on TQMa8MxML-ADAP */
&gpio2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0hub_sel>;
sel-usb-hub-hog {
gpio-hog;
gpios = <1 GPIO_ACTIVE_HIGH>;
output-high;
};
};
&i2c1 {
expander2: gpio@27 {
compatible = "nxp,pca9555";
reg = <0x27>;
gpio-controller;
#gpio-cells = <2>;
vcc-supply = <&reg_vcc_3v3>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_expander2>;
interrupt-parent = <&gpio1>;
interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
&sai3 {
assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
clocks = <&clk IMX8MN_CLK_SAI3_IPG>, <&clk IMX8MN_CLK_DUMMY>,
<&clk IMX8MN_CLK_SAI3_ROOT>, <&clk IMX8MN_CLK_DUMMY>,
<&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_AUDIO_PLL1_OUT>,
<&clk IMX8MN_AUDIO_PLL2_OUT>;
};
&tlv320aic3x04 {
clock-names = "mclk";
clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
};
&usbotg1 {
dr_mode = "host";
disable-over-current;
power-active-high;
status = "okay";
};
&iomuxc {
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000146>,
<MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000146>,
<MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000146>,
<MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000146>;
};
pinctrl_ecspi2: ecspi2grp {
fsl,pins = <MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000146>,
<MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000146>,
<MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000146>,
<MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000146>;
};
pinctrl_expander2: expander2grp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94>;
};
pinctrl_fec1: fec1grp {
fsl,pins = <MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002>,
<MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002>,
<MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14>,
<MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14>,
<MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14>,
<MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14>,
<MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90>,
<MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90>,
<MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90>,
<MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90>,
<MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14>,
<MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90>,
<MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90>,
<MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14>;
};
pinctrl_gpiobutton: gpiobuttongrp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84>,
<MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84>,
<MX8MN_IOMUXC_SD1_CLK_GPIO2_IO0 0x84>;
};
pinctrl_gpioled: gpioledgrp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84>,
<MX8MN_IOMUXC_NAND_DQS_GPIO3_IO14 0x84>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001C4>,
<MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001C4>;
};
pinctrl_i2c2_gpio: i2c2gpiogrp {
fsl,pins = <MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001C4>,
<MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001C4>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001C4>,
<MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001C4>;
};
pinctrl_i2c3_gpio: i2c3gpiogrp {
fsl,pins = <MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001C4>,
<MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001C4>;
};
pinctrl_pwm3: pwm3grp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14>;
};
pinctrl_pwm4: pwm4grp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14>;
};
pinctrl_sai3: sai3grp {
fsl,pins = <MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94>,
<MX8MN_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94>,
<MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94>,
<MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94>,
<MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94>,
<MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94>,
<MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16>,
<MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16>,
<MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16>;
};
pinctrl_uart3: uart3grp {
fsl,pins = <MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16>,
<MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16>;
};
pinctrl_uart4: uart4grp {
fsl,pins = <MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16>,
<MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16>;
};
pinctrl_usb0hub_sel: usb0hub-selgrp {
/* SEL_USB_HUB_B */
fsl,pins = <MX8MN_IOMUXC_SD1_CMD_GPIO2_IO1 0x84>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x84>,
<MX8MN_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84>,
<MX8MN_IOMUXC_GPIO1_IO10_USB1_OTG_ID 0x1C4>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
<MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
<MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
};
pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
fsl,pins = <MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
<MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
<MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
};
pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
fsl,pins = <MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4>,
<MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4>,
<MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4>,
<MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84>;
};
pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
fsl,pins = <MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84>;
};
};
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi 0 → 100644
View file @ 3e56e354
// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
/*
* Copyright 2020-2021 TQ-Systems GmbH
*/
#include "imx8mn.dtsi"
/ {
model = "TQ-Systems i.MX8MN TQMa8MxNL";
compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
memory@40000000 {
device_type = "memory";
/* our minimum RAM config will be 1024 MiB */
reg = <0x00000000 0x40000000 0 0x40000000>;
};
/* e-MMC IO, needed for HS modes */
reg_vcc1v8: regulator-vcc1v8 {
compatible = "regulator-fixed";
regulator-name = "TQMA8MXNL_VCC1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
reg_vcc3v3: regulator-vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "TQMA8MXNL_VCC3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
/* global autoconfigured region for contiguous allocations */
linux,cma {
compatible = "shared-dma-pool";
reusable;
/* 640 MiB */
size = <0 0x28000000>;
/* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
alloc-ranges = <0 0x40000000 0 0x78000000>;
linux,cma-default;
};
};
};
&A53_0 {
cpu-supply = <&buck2_reg>;
};
&flexspi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexspi>;
status = "okay";
flash0: flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <84000000>;
spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>;
};
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "okay";
sensor0: temperature-sensor-eeprom@1b {
compatible = "nxp,se97", "jedec,jc-42.4-temp";
reg = <0x1b>;
};
pca9450: pmic@25 {
compatible = "nxp,pca9450a";
reg = <0x25>;
/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
pinctrl-0 = <&pinctrl_pmic>;
pinctrl-names = "default";
interrupt-parent = <&gpio1>;
interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
regulators {
/* V_0V85_SOC: 0.85 .. 0.95 */
buck1_reg: BUCK1 {
regulator-name = "BUCK1";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <950000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <3125>;
};
/* VDD_ARM */
buck2_reg: BUCK2 {
regulator-name = "BUCK2";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
nxp,dvs-run-voltage = <950000>;
nxp,dvs-standby-voltage = <850000>;
regulator-ramp-delay = <3125>;
};
/* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
buck3_reg: BUCK3 {
regulator-name = "BUCK3";
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <950000>;
regulator-boot-on;
regulator-always-on;
regulator-ramp-delay = <3125>;
};
/* VCC3V3 -> VMMC, ... must not be changed */
buck4_reg: BUCK4 {
regulator-name = "BUCK4";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
buck5_reg: BUCK5 {
regulator-name = "BUCK5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
/* V_1V1 -> RAM, ... must not be changed */
buck6_reg: BUCK6 {
regulator-name = "BUCK6";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-boot-on;
regulator-always-on;
};
/* V_1V8_SNVS */
ldo1_reg: LDO1 {
regulator-name = "LDO1";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
/* V_0V8_SNVS */
ldo2_reg: LDO2 {
regulator-name = "LDO2";
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <850000>;
regulator-boot-on;
regulator-always-on;
};
/* V_1V8_ANA */
ldo3_reg: LDO3 {
regulator-name = "LDO3";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
/* V_0V9_MIPI */
ldo4_reg: LDO4 {
regulator-name = "LDO4";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
regulator-boot-on;
regulator-always-on;
};
/* VCC SD IO - switched using SD2 VSELECT */
ldo5_reg: LDO5 {
regulator-name = "LDO5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
};
};
pcf85063: rtc@51 {
compatible = "nxp,pcf85063a";
reg = <0x51>;
quartz-load-femtofarads = <7000>;
};
eeprom1: eeprom@53 {
compatible = "nxp,se97b", "atmel,24c02";
read-only;
reg = <0x53>;
pagesize = <16>;
};
eeprom0: eeprom@57 {
compatible = "atmel,24c64";
reg = <0x57>;
pagesize = <32>;
};
};
&usdhc3 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3>;
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
bus-width = <8>;
non-removable;
no-sd;
no-sdio;
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc1v8>;
status = "okay";
};
/*
* Attention:
* wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
* without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
*/
&wdog1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog>;
fsl,ext-reset-output;
status = "okay";
};
&iomuxc {
pinctrl_flexspi: flexspigrp {
fsl,pins = <MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x84>,
<MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x84>,
<MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x84>,
<MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x84>,
<MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x84>,
<MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x84>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c4>,
<MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c4>;
};
pinctrl_i2c1_gpio: i2c1gpiogrp {
fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c4>,
<MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c4>;
};
pinctrl_pmic: pmicgrp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x84>;
};
pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
fsl,pins = <MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4>,
<MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
<MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
<MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
<MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
<MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
<MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
<MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
<MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84>;
};
pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2>,
<MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
<MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
<MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
<MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
<MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
<MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
<MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
<MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84>;
};
pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6>,
<MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2>,
<MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4>,
<MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4>,
<MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4>,
<MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4>,
<MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4>,
<MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4>,
<MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84>,
<MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84>;
};
pinctrl_wdog: wdoggrp {
fsl,pins = <MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84>;
};
};
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7