Merge tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a larger than normal update for Arm SoC specific code, most of
  it in device trees, but also drivers and the omap and at91/sama7
  platforms:

   - There are four new entries to the MAINTAINERS file: Sven Peter and
     Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
     and Vignesh Raghavendra for TI K3

   - Build fixes to address randconfig warnings in sharpsl, dove, omap1,
     and qcom platforms as well as the scmi and op-tee subsystems

   - Regression fixes for missing CONFIG_FB and other options for
     several defconfigs

   - Several bug fixes for the newly added Microchip SAMA7 platform,
     mostly regarding power management

   - Missing SMP barriers to protect accesses to SCMI virtio device

   - Regression fixes for TI OMAP, including a boot-time hang on am335x.

   - Lots of bug fixes for NXP i.MX, mostly addressing incorrect
     settings in devicetree files, and one revert for broken suspend.

   - Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
     of schema warnings.

   - Regression fixes for qualcomm SoC specific drivers and devicetree
     files, reverting an mdt_loader change and at least pastially
     reverting some of the 5.15 DTS changes, plus some minor bugfixes"

* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
  MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
  MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
  firmware: arm_scmi: Add proper barriers to scmi virtio device
  firmware: arm_scmi: Simplify spinlocks in virtio transport
  ARM: dts: omap3430-sdp: Fix NAND device node
  bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
  ARM: sharpsl_param: work around -Wstringop-overread warning
  ARM: defconfig: gemini: Restore framebuffer
  ARM: dove: mark 'putc' as inline
  ARM: omap1: move omap15xx local bus handling to usb.c
  MAINTAINERS: Add Vignesh to TI K3 platform maintainership
  arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
  ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
  arm64: dts: ls1028a: fix eSDHC2 node
  arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
  ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
  ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
  ARM: at91: pm: preload base address of controllers in tlb
  ARM: at91: pm: group constants and addresses loading
  ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
  ...

MAINTAINERS

@@ -1276,6 +1276,7 @@ F:	drivers/input/mouse/bcm5974.c
 
 APPLE DART IOMMU DRIVER
 M:	Sven Peter <sven@svenpeter.dev>
+R:	Alyssa Rosenzweig <alyssa@rosenzweig.io>
 L:	iommu@lists.linux-foundation.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/iommu/apple,dart.yaml
@@ -1712,6 +1713,8 @@ F:	drivers/*/*alpine*
 
 ARM/APPLE MACHINE SUPPORT
 M:	Hector Martin <marcan@marcan.st>
+M:	Sven Peter <sven@svenpeter.dev>
+R:	Alyssa Rosenzweig <alyssa@rosenzweig.io>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 W:	https://asahilinux.org
@@ -2237,6 +2240,7 @@ F:	arch/arm/mach-pxa/mioa701.c
 
 ARM/MStar/Sigmastar Armv7 SoC support
 M:	Daniel Palmer <daniel@thingy.jp>
+M:	Romain Perier <romain.perier@gmail.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 W:	http://linux-chenxing.org/
@@ -2713,6 +2717,7 @@ F:	drivers/power/reset/keystone-reset.c
 
 ARM/TEXAS INSTRUMENTS K3 ARCHITECTURE
 M:	Nishanth Menon <nm@ti.com>
+M:	Vignesh Raghavendra <vigneshr@ti.com>
 M:	Tero Kristo <kristo@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Supported

arch/arm/boot/dts/at91-sama5d27_som1_ek.dts

@@ -71,7 +71,6 @@ apb {
 			isc: isc@f0008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
-				status = "okay";
 			};
 
 			qspi1: spi@f0024000 {

arch/arm/boot/dts/at91-sama7g5ek.dts

@@ -196,11 +196,13 @@ vddioddr: VDD_DDR {
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1350000>;
 						regulator-mode = <4>;
 					};
 
 					regulator-state-mem {
 						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1350000>;
 						regulator-mode = <4>;
 					};
 				};
@@ -353,7 +355,10 @@ &gmac0 {
 	#address-cells = <1>;
 	#size-cells = <0>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gmac0_default &pinctrl_gmac0_txck_default &pinctrl_gmac0_phy_irq>;
+	pinctrl-0 = <&pinctrl_gmac0_default
+		     &pinctrl_gmac0_mdio_default
+		     &pinctrl_gmac0_txck_default
+		     &pinctrl_gmac0_phy_irq>;
 	phy-mode = "rgmii-id";
 	status = "okay";
 
@@ -368,7 +373,9 @@ &gmac1 {
 	#address-cells = <1>;
 	#size-cells = <0>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gmac1_default &pinctrl_gmac1_phy_irq>;
+	pinctrl-0 = <&pinctrl_gmac1_default
+		     &pinctrl_gmac1_mdio_default
+		     &pinctrl_gmac1_phy_irq>;
 	phy-mode = "rmii";
 	status = "okay";
 
@@ -423,14 +430,20 @@ pinctrl_gmac0_default: gmac0_default {
 			 <PIN_PA15__G0_TXEN>,
 			 <PIN_PA30__G0_RXCK>,
 			 <PIN_PA18__G0_RXDV>,
-			 <PIN_PA22__G0_MDC>,
-			 <PIN_PA23__G0_MDIO>,
 			 <PIN_PA25__G0_125CK>;
+		slew-rate = <0>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_mdio_default: gmac0_mdio_default {
+		pinmux = <PIN_PA22__G0_MDC>,
+			 <PIN_PA23__G0_MDIO>;
 		bias-disable;
 	};
 
 	pinctrl_gmac0_txck_default: gmac0_txck_default {
 		pinmux = <PIN_PA24__G0_TXCK>;
+		slew-rate = <0>;
 		bias-pull-up;
 	};
 
@@ -447,8 +460,13 @@ pinctrl_gmac1_default: gmac1_default {
 			 <PIN_PD25__G1_RX0>,
 			 <PIN_PD26__G1_RX1>,
 			 <PIN_PD27__G1_RXER>,
-			 <PIN_PD24__G1_RXDV>,
-			 <PIN_PD28__G1_MDC>,
+			 <PIN_PD24__G1_RXDV>;
+		slew-rate = <0>;
+		bias-disable;
+	};
+
+	pinctrl_gmac1_mdio_default: gmac1_mdio_default {
+		pinmux = <PIN_PD28__G1_MDC>,
 			 <PIN_PD29__G1_MDIO>;
 		bias-disable;
 	};
@@ -540,6 +558,7 @@ cmd_data {
 				 <PIN_PA8__SDMMC0_DAT5>,
 				 <PIN_PA9__SDMMC0_DAT6>,
 				 <PIN_PA10__SDMMC0_DAT7>;
+			slew-rate = <0>;
 			bias-pull-up;
 		};
 
@@ -547,6 +566,7 @@ ck_cd_rstn_vddsel {
 			pinmux = <PIN_PA0__SDMMC0_CK>,
 				 <PIN_PA2__SDMMC0_RSTN>,
 				 <PIN_PA11__SDMMC0_DS>;
+			slew-rate = <0>;
 			bias-pull-up;
 		};
 	};
@@ -558,6 +578,7 @@ cmd_data {
 				 <PIN_PC0__SDMMC1_DAT1>,
 				 <PIN_PC1__SDMMC1_DAT2>,
 				 <PIN_PC2__SDMMC1_DAT3>;
+			slew-rate = <0>;
 			bias-pull-up;
 		};
 
@@ -566,6 +587,7 @@ ck_cd_rstn_vddsel {
 				 <PIN_PB28__SDMMC1_RSTN>,
 				 <PIN_PC5__SDMMC1_1V8SEL>,
 				 <PIN_PC4__SDMMC1_CD>;
+			slew-rate = <0>;
 			bias-pull-up;
 		};
 	};
@@ -577,11 +599,13 @@ cmd_data {
 				 <PIN_PD6__SDMMC2_DAT1>,
 				 <PIN_PD7__SDMMC2_DAT2>,
 				 <PIN_PD8__SDMMC2_DAT3>;
+			slew-rate = <0>;
 			bias-pull-up;
 		};
 
 		ck {
 			pinmux = <PIN_PD4__SDMMC2_CK>;
+			slew-rate = <0>;
 			bias-pull-up;
 		};
 	};
@@ -634,6 +658,15 @@ &sdmmc2 {
 	pinctrl-0 = <&pinctrl_sdmmc2_default>;
 };
 
+&shdwc {
+	atmel,shdwc-debouncer = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
 &spdifrx {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spdifrx_default>;

arch/arm/boot/dts/imx53-m53menlo.dts

@@ -56,6 +56,7 @@ eth {
 	panel {
 		compatible = "edt,etm0700g0dh6";
 		pinctrl-0 = <&pinctrl_display_gpio>;
+		pinctrl-names = "default";
 		enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
 
 		port {
@@ -76,8 +77,7 @@ reg_usbh1_vbus: regulator-usbh1-vbus {
 		regulator-name = "vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		gpio = <&gpio1 2 0>;
 	};
 };
 

arch/arm/boot/dts/imx6dl-yapp4-common.dtsi

@@ -5,6 +5,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pwm/pwm.h>
 
 / {
@@ -277,6 +278,7 @@ chan@0 {
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
 			reg = <0>;
+			color = <LED_COLOR_ID_RED>;
 		};
 
 		chan@1 {
@@ -284,6 +286,7 @@ chan@1 {
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
 			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
 		};
 
 		chan@2 {
@@ -291,6 +294,7 @@ chan@2 {
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
 			reg = <2>;
+			color = <LED_COLOR_ID_BLUE>;
 		};
 
 		chan@3 {
@@ -298,6 +302,7 @@ chan@3 {
 			led-cur = /bits/ 8 <0x0>;
 			max-cur = /bits/ 8 <0x0>;
 			reg = <3>;
+			color = <LED_COLOR_ID_WHITE>;
 		};
 	};
 

arch/arm/boot/dts/imx6qdl-pico.dtsi

@@ -176,7 +176,18 @@ &fec {
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+	phy-handle = <&phy>;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@1 {
+			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
 };
 
 &hdmi {

arch/arm/boot/dts/imx6sx-sdb.dts

@@ -114,7 +114,7 @@ flash0: n25q256a@0 {
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 
@@ -124,7 +124,7 @@ flash1: n25q256a@2 {
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <2>;
 	};
 };

arch/arm/boot/dts/imx6ul-14x14-evk.dtsi

@@ -292,7 +292,7 @@ flash0: n25q256a@0 {
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 };

arch/arm/boot/dts/omap3430-sdp.dts

@@ -101,7 +101,7 @@ partition@280000 {
 
 	nand@1,0 {
 		compatible = "ti,omap2-nand";
-		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		reg = <1 0 4>; /* CS1, offset 0, IO size 4 */
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */

arch/arm/boot/dts/qcom-apq8064.dtsi

@@ -198,7 +198,7 @@ cxo_board: cxo_board {
 			clock-frequency = <19200000>;
 		};
 
-		pxo_board {
+		pxo_board: pxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <27000000>;
@@ -1148,22 +1148,21 @@ tcsr: syscon@1a400000 {
 		};
 
 		gpu: adreno-3xx@4300000 {
-			compatible = "qcom,adreno-3xx";
+			compatible = "qcom,adreno-320.2", "qcom,adreno";
 			reg = <0x04300000 0x20000>;
 			reg-names = "kgsl_3d0_reg_memory";
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "kgsl_3d0_irq";
 			clock-names =
-			    "core_clk",
-			    "iface_clk",
-			    "mem_clk",
-			    "mem_iface_clk";
+			    "core",
+			    "iface",
+			    "mem",
+			    "mem_iface";
 			clocks =
 			    <&mmcc GFX3D_CLK>,
 			    <&mmcc GFX3D_AHB_CLK>,
 			    <&mmcc GFX3D_AXI_CLK>,
 			    <&mmcc MMSS_IMEM_AHB_CLK>;
-			qcom,chipid = <0x03020002>;
 
 			iommus = <&gfx3d 0
 				  &gfx3d 1
@@ -1306,7 +1305,7 @@ dsi0_phy: dsi-phy@4700200 {
 			reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
 			clock-names = "iface_clk", "ref";
 			clocks = <&mmcc DSI_M_AHB_CLK>,
-				 <&cxo_board>;
+				 <&pxo_board>;
 		};
 
 

arch/arm/boot/dts/sama7g5.dtsi

@@ -75,6 +75,17 @@ soc {
 		#size-cells = <1>;
 		ranges;
 
+		securam: securam@e0000000 {
+			compatible = "microchip,sama7g5-securam", "atmel,sama5d2-securam", "mmio-sram";
+			reg = <0xe0000000 0x4000>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xe0000000 0x4000>;
+			no-memory-wc;
+			status = "okay";
+		};
+
 		secumod: secumod@e0004000 {
 			compatible = "microchip,sama7g5-secumod", "atmel,sama5d2-secumod", "syscon";
 			reg = <0xe0004000 0x4000>;
@@ -111,6 +122,17 @@ pmc: pmc@e0018000 {
 			clock-names = "td_slck", "md_slck", "main_xtal";
 		};
 
+		shdwc: shdwc@e001d010 {
+			compatible = "microchip,sama7g5-shdwc", "syscon";
+			reg = <0xe001d010 0x10>;
+			clocks = <&clk32k 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			atmel,wakeup-rtc-timer;
+			atmel,wakeup-rtt-timer;
+			status = "disabled";
+		};
+
 		rtt: rtt@e001d020 {
 			compatible = "microchip,sama7g5-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
 			reg = <0xe001d020 0x30>;
@@ -137,6 +159,11 @@ ps_wdt: watchdog@e001d180 {
 			clocks = <&clk32k 0>;
 		};
 
+		chipid@e0020000 {
+			compatible = "microchip,sama7g5-chipid";
+			reg = <0xe0020000 0x8>;
+		};
+
 		sdmmc0: mmc@e1204000 {
 			compatible = "microchip,sama7g5-sdhci", "microchip,sam9x60-sdhci";
 			reg = <0xe1204000 0x4000>;
@@ -515,6 +542,18 @@ spi11: spi@400 {
 			};
 		};
 
+		uddrc: uddrc@e3800000 {
+			compatible = "microchip,sama7g5-uddrc";
+			reg = <0xe3800000 0x4000>;
+			status = "okay";
+		};
+
+		ddr3phy: ddr3phy@e3804000 {
+			compatible = "microchip,sama7g5-ddr3phy";
+			reg = <0xe3804000 0x1000>;
+			status = "okay";
+		};
+
 		gic: interrupt-controller@e8c11000 {
 			compatible = "arm,cortex-a7-gic";
 			#interrupt-cells = <3>;

arch/arm/boot/dts/vexpress-v2m-rs1.dtsi

@@ -17,6 +17,7 @@
  * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
  * CHANGES TO vexpress-v2m.dtsi!
  */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	v2m_fixed_3v3: fixed-regulator-0 {
@@ -101,16 +102,68 @@ led-8 {
 	};
 
 	bus@8000000 {
-		motherboard-bus {
-			model = "V2M-P1";
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 63>;
+		interrupt-map = <0  0 &gic GIC_SPI  0 IRQ_TYPE_LEVEL_HIGH>,
+				<0  1 &gic GIC_SPI  1 IRQ_TYPE_LEVEL_HIGH>,
+				<0  2 &gic GIC_SPI  2 IRQ_TYPE_LEVEL_HIGH>,
+				<0  3 &gic GIC_SPI  3 IRQ_TYPE_LEVEL_HIGH>,
+				<0  4 &gic GIC_SPI  4 IRQ_TYPE_LEVEL_HIGH>,
+				<0  5 &gic GIC_SPI  5 IRQ_TYPE_LEVEL_HIGH>,
+				<0  6 &gic GIC_SPI  6 IRQ_TYPE_LEVEL_HIGH>,
+				<0  7 &gic GIC_SPI  7 IRQ_TYPE_LEVEL_HIGH>,
+				<0  8 &gic GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+				<0  9 &gic GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+				<0 10 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				<0 11 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				<0 12 &gic GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				<0 13 &gic GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				<0 14 &gic GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				<0 15 &gic GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				<0 16 &gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				<0 17 &gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				<0 18 &gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				<0 19 &gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+				<0 20 &gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				<0 21 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				<0 22 &gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+				<0 23 &gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+				<0 24 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				<0 25 &gic GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				<0 26 &gic GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				<0 27 &gic GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				<0 28 &gic GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+				<0 29 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				<0 30 &gic GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				<0 31 &gic GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				<0 32 &gic GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				<0 33 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				<0 34 &gic GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				<0 35 &gic GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+				<0 36 &gic GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+				<0 37 &gic GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+				<0 38 &gic GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+				<0 39 &gic GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				<0 40 &gic GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				<0 41 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				<0 42 &gic GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+
+		motherboard-bus@8000000 {
 			arm,hbi = <0x190>;
 			arm,vexpress,site = <0>;
-			arm,v2m-memory-map = "rs1";
 			compatible = "arm,vexpress,v2m-p1", "simple-bus";
 			#address-cells = <2>; /* SMB chipselect number and offset */
 			#size-cells = <1>;
-			#interrupt-cells = <1>;
-			ranges;
+			ranges = <0 0 0x08000000 0x04000000>,
+				 <1 0 0x14000000 0x04000000>,
+				 <2 0 0x18000000 0x04000000>,
+				 <3 0 0x1c000000 0x04000000>,
+				 <4 0 0x0c000000 0x04000000>,
+				 <5 0 0x10000000 0x04000000>;
 
 			nor_flash: flash@0 {
 				compatible = "arm,vexpress-flash", "cfi-flash";
@@ -215,7 +268,7 @@ aaci@40000 {
 					clock-names = "apb_pclk";
 				};
 
-				mmci@50000 {
+				mmc@50000 {
 					compatible = "arm,pl180", "arm,primecell";
 					reg = <0x050000 0x1000>;
 					interrupts = <9>, <10>;
@@ -275,7 +328,7 @@ v2m_serial3: serial@c0000 {
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				wdt@f0000 {
+				watchdog@f0000 {
 					compatible = "arm,sp805", "arm,primecell";
 					reg = <0x0f0000 0x1000>;
 					interrupts = <0>;

arch/arm/boot/dts/vexpress-v2m.dtsi

@@ -17,18 +17,73 @@
  * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT
  * CHANGES TO vexpress-v2m-rs1.dtsi!
  */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
-	bus@4000000 {
-		motherboard {
-			model = "V2M-P1";
+	bus@40000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x40000000 0x40000000 0x10000000>,
+			 <0x10000000 0x10000000 0x00020000>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 63>;
+		interrupt-map = <0  0 &gic GIC_SPI  0 IRQ_TYPE_LEVEL_HIGH>,
+				<0  1 &gic GIC_SPI  1 IRQ_TYPE_LEVEL_HIGH>,
+				<0  2 &gic GIC_SPI  2 IRQ_TYPE_LEVEL_HIGH>,
+				<0  3 &gic GIC_SPI  3 IRQ_TYPE_LEVEL_HIGH>,
+				<0  4 &gic GIC_SPI  4 IRQ_TYPE_LEVEL_HIGH>,
+				<0  5 &gic GIC_SPI  5 IRQ_TYPE_LEVEL_HIGH>,
+				<0  6 &gic GIC_SPI  6 IRQ_TYPE_LEVEL_HIGH>,
+				<0  7 &gic GIC_SPI  7 IRQ_TYPE_LEVEL_HIGH>,
+				<0  8 &gic GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+				<0  9 &gic GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+				<0 10 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				<0 11 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				<0 12 &gic GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				<0 13 &gic GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				<0 14 &gic GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				<0 15 &gic GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				<0 16 &gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				<0 17 &gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				<0 18 &gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				<0 19 &gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+				<0 20 &gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				<0 21 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				<0 22 &gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+				<0 23 &gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+				<0 24 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				<0 25 &gic GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				<0 26 &gic GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				<0 27 &gic GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				<0 28 &gic GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+				<0 29 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				<0 30 &gic GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				<0 31 &gic GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				<0 32 &gic GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				<0 33 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				<0 34 &gic GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				<0 35 &gic GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+				<0 36 &gic GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+				<0 37 &gic GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+				<0 38 &gic GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+				<0 39 &gic GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				<0 40 &gic GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				<0 41 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				<0 42 &gic GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+
+		motherboard-bus@40000000 {
 			arm,hbi = <0x190>;
 			arm,vexpress,site = <0>;
 			compatible = "arm,vexpress,v2m-p1", "simple-bus";
 			#address-cells = <2>; /* SMB chipselect number and offset */
 			#size-cells = <1>;
-			#interrupt-cells = <1>;
-			ranges;
+			ranges = <0 0 0x40000000 0x04000000>,
+				 <1 0 0x44000000 0x04000000>,
+				 <2 0 0x48000000 0x04000000>,
+				 <3 0 0x4c000000 0x04000000>,
+				 <7 0 0x10000000 0x00020000>;
 
 			flash@0,00000000 {
 				compatible = "arm,vexpress-flash", "cfi-flash";

arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts

@@ -237,62 +237,7 @@ energy {
 	};
 
 	bus@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
+		ranges = <0x8000000 0 0x8000000 0x18000000>;
 	};
 
 	site2: hsb@40000000 {

arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts

@@ -609,62 +609,7 @@ etm2_out_port: endpoint {
 	};
 
 	smb: bus@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
+		ranges = <0x8000000 0 0x8000000 0x18000000>;
 	};
 
 	site2: hsb@40000000 {

arch/arm/boot/dts/vexpress-v2p-ca5s.dts

@@ -207,62 +207,7 @@ temp-dcc {
 	};
 
 	smb: bus@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x04000000>,
-			 <1 0 0x14000000 0x04000000>,
-			 <2 0 0x18000000 0x04000000>,
-			 <3 0 0x1c000000 0x04000000>,
-			 <4 0 0x0c000000 0x04000000>,
-			 <5 0 0x10000000 0x04000000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
+		ranges = <0 0x8000000 0x18000000>;
 	};
 
 	site2: hsb@40000000 {

arch/arm/boot/dts/vexpress-v2p-ca9.dts

@@ -295,64 +295,6 @@ power-vd10-s3 {
 		};
 	};
 
-	smb: bus@4000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x40000000 0x04000000>,
-			 <1 0 0x44000000 0x04000000>,
-			 <2 0 0x48000000 0x04000000>,
-			 <3 0 0x4c000000 0x04000000>,
-			 <7 0 0x10000000 0x00020000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic 0  0 4>,
-				<0 0  1 &gic 0  1 4>,
-				<0 0  2 &gic 0  2 4>,
-				<0 0  3 &gic 0  3 4>,
-				<0 0  4 &gic 0  4 4>,
-				<0 0  5 &gic 0  5 4>,
-				<0 0  6 &gic 0  6 4>,
-				<0 0  7 &gic 0  7 4>,
-				<0 0  8 &gic 0  8 4>,
-				<0 0  9 &gic 0  9 4>,
-				<0 0 10 &gic 0 10 4>,
-				<0 0 11 &gic 0 11 4>,
-				<0 0 12 &gic 0 12 4>,
-				<0 0 13 &gic 0 13 4>,
-				<0 0 14 &gic 0 14 4>,
-				<0 0 15 &gic 0 15 4>,
-				<0 0 16 &gic 0 16 4>,
-				<0 0 17 &gic 0 17 4>,
-				<0 0 18 &gic 0 18 4>,
-				<0 0 19 &gic 0 19 4>,
-				<0 0 20 &gic 0 20 4>,
-				<0 0 21 &gic 0 21 4>,
-				<0 0 22 &gic 0 22 4>,
-				<0 0 23 &gic 0 23 4>,
-				<0 0 24 &gic 0 24 4>,
-				<0 0 25 &gic 0 25 4>,
-				<0 0 26 &gic 0 26 4>,
-				<0 0 27 &gic 0 27 4>,
-				<0 0 28 &gic 0 28 4>,
-				<0 0 29 &gic 0 29 4>,
-				<0 0 30 &gic 0 30 4>,
-				<0 0 31 &gic 0 31 4>,
-				<0 0 32 &gic 0 32 4>,
-				<0 0 33 &gic 0 33 4>,
-				<0 0 34 &gic 0 34 4>,
-				<0 0 35 &gic 0 35 4>,
-				<0 0 36 &gic 0 36 4>,
-				<0 0 37 &gic 0 37 4>,
-				<0 0 38 &gic 0 38 4>,
-				<0 0 39 &gic 0 39 4>,
-				<0 0 40 &gic 0 40 4>,
-				<0 0 41 &gic 0 41 4>,
-				<0 0 42 &gic 0 42 4>;
-	};
-
 	site2: hsb@e0000000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;

arch/arm/common/sharpsl_param.c

@@ -40,7 +40,9 @@ EXPORT_SYMBOL(sharpsl_param);
 
 void sharpsl_save_param(void)
 {
-	memcpy(&sharpsl_param, param_start(PARAM_BASE), sizeof(struct sharpsl_param_info));
+	struct sharpsl_param_info *params = param_start(PARAM_BASE);
+
+	memcpy(&sharpsl_param, params, sizeof(*params));
 
 	if (sharpsl_param.comadj_keyword != COMADJ_MAGIC)
 		sharpsl_param.comadj=-1;

arch/arm/configs/gemini_defconfig

@@ -76,6 +76,7 @@ CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_ILITEK_IL9322=y
 CONFIG_DRM_TVE200=y
+CONFIG_FB=y
 CONFIG_LOGO=y
 CONFIG_USB=y
 CONFIG_USB_MON=y

arch/arm/configs/imx_v6_v7_defconfig

@@ -292,6 +292,7 @@ CONFIG_DRM_IMX_LDB=y
 CONFIG_DRM_IMX_HDMI=y
 CONFIG_DRM_ETNAVIV=y
 CONFIG_DRM_MXSFB=y
+CONFIG_FB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_LCD_L4F00242T03=y

arch/arm/configs/multi_v7_defconfig

@@ -456,6 +456,7 @@ CONFIG_PINCTRL_STMFX=y
 CONFIG_PINCTRL_PALMAS=y
 CONFIG_PINCTRL_OWL=y
 CONFIG_PINCTRL_S500=y
+CONFIG_PINCTRL_MSM=y
 CONFIG_PINCTRL_APQ8064=y
 CONFIG_PINCTRL_APQ8084=y
 CONFIG_PINCTRL_IPQ8064=y
@@ -725,6 +726,7 @@ CONFIG_DRM_PL111=m
 CONFIG_DRM_LIMA=m
 CONFIG_DRM_PANFROST=m
 CONFIG_DRM_ASPEED_GFX=m
+CONFIG_FB=y
 CONFIG_FB_EFI=y
 CONFIG_FB_WM8505=y
 CONFIG_FB_SH_MOBILE_LCDC=y
@@ -1122,6 +1124,7 @@ CONFIG_PHY_DM816X_USB=m
 CONFIG_OMAP_USB2=y
 CONFIG_TI_PIPE3=y
 CONFIG_TWL4030_USB=m
+CONFIG_RAS=y
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_ROCKCHIP_EFUSE=m
 CONFIG_NVMEM_SUNXI_SID=y

arch/arm/mach-at91/pm.c

@@ -47,12 +47,26 @@ struct at91_pm_bu {
 	unsigned long ddr_phy_calibration[BACKUP_DDR_PHY_CALIBRATION];
 };
 
+/*
+ * struct at91_pm_sfrbu_offsets: registers mapping for SFRBU
+ * @pswbu: power switch BU control registers
+ */
+struct at91_pm_sfrbu_regs {
+	struct {
+		u32 key;
+		u32 ctrl;
+		u32 state;
+		u32 softsw;
+	} pswbu;
+};
+
 /**
  * struct at91_soc_pm - AT91 SoC power management data structure
  * @config_shdwc_ws: wakeup sources configuration function for SHDWC
  * @config_pmc_ws: wakeup srouces configuration function for PMC
  * @ws_ids: wakup sources of_device_id array
  * @data: PM data to be used on last phase of suspend
+ * @sfrbu_regs: SFRBU registers mapping
  * @bu: backup unit mapped data (for backup mode)
  * @memcs: memory chip select
  */
@@ -62,6 +76,7 @@ struct at91_soc_pm {
 	const struct of_device_id *ws_ids;
 	struct at91_pm_bu *bu;
 	struct at91_pm_data data;
+	struct at91_pm_sfrbu_regs sfrbu_regs;
 	void *memcs;
 };
 
@@ -356,9 +371,36 @@ static int at91_suspend_finish(unsigned long val)
 	return 0;
 }
 
+static void at91_pm_switch_ba_to_vbat(void)
+{
+	unsigned int offset = offsetof(struct at91_pm_sfrbu_regs, pswbu);
+	unsigned int val;
+
+	/* Just for safety. */
+	if (!soc_pm.data.sfrbu)
+		return;
+
+	val = readl(soc_pm.data.sfrbu + offset);
+
+	/* Already on VBAT. */
+	if (!(val & soc_pm.sfrbu_regs.pswbu.state))
+		return;
+
+	val &= ~soc_pm.sfrbu_regs.pswbu.softsw;
+	val |= soc_pm.sfrbu_regs.pswbu.key | soc_pm.sfrbu_regs.pswbu.ctrl;
+	writel(val, soc_pm.data.sfrbu + offset);
+
+	/* Wait for update. */
+	val = readl(soc_pm.data.sfrbu + offset);
+	while (val & soc_pm.sfrbu_regs.pswbu.state)
+		val = readl(soc_pm.data.sfrbu + offset);
+}
+
 static void at91_pm_suspend(suspend_state_t state)
 {
 	if (soc_pm.data.mode == AT91_PM_BACKUP) {
+		at91_pm_switch_ba_to_vbat();
+
 		cpu_suspend(0, at91_suspend_finish);
 
 		/* The SRAM is lost between suspend cycles */
@@ -589,18 +631,22 @@ static const struct of_device_id ramc_phy_ids[] __initconst = {
 	{ /* Sentinel. */ },
 };
 
-static __init void at91_dt_ramc(bool phy_mandatory)
+static __init int at91_dt_ramc(bool phy_mandatory)
 {
 	struct device_node *np;
 	const struct of_device_id *of_id;
 	int idx = 0;
 	void *standby = NULL;
 	const struct ramc_info *ramc;
+	int ret;
 
 	for_each_matching_node_and_match(np, ramc_ids, &of_id) {
 		soc_pm.data.ramc[idx] = of_iomap(np, 0);
-		if (!soc_pm.data.ramc[idx])
-			panic(pr_fmt("unable to map ramc[%d] cpu registers\n"), idx);
+		if (!soc_pm.data.ramc[idx]) {
+			pr_err("unable to map ramc[%d] cpu registers\n", idx);
+			ret = -ENOMEM;
+			goto unmap_ramc;
+		}
 
 		ramc = of_id->data;
 		if (ramc) {
@@ -612,25 +658,42 @@ static __init void at91_dt_ramc(bool phy_mandatory)
 		idx++;
 	}
 
-	if (!idx)
-		panic(pr_fmt("unable to find compatible ram controller node in dtb\n"));
+	if (!idx) {
+		pr_err("unable to find compatible ram controller node in dtb\n");
+		ret = -ENODEV;
+		goto unmap_ramc;
+	}
 
 	/* Lookup for DDR PHY node, if any. */
 	for_each_matching_node_and_match(np, ramc_phy_ids, &of_id) {
 		soc_pm.data.ramc_phy = of_iomap(np, 0);
-		if (!soc_pm.data.ramc_phy)
-			panic(pr_fmt("unable to map ramc phy cpu registers\n"));
+		if (!soc_pm.data.ramc_phy) {
+			pr_err("unable to map ramc phy cpu registers\n");
+			ret = -ENOMEM;
+			goto unmap_ramc;
+		}
 	}
 
-	if (phy_mandatory && !soc_pm.data.ramc_phy)
-		panic(pr_fmt("DDR PHY is mandatory!\n"));
+	if (phy_mandatory && !soc_pm.data.ramc_phy) {
+		pr_err("DDR PHY is mandatory!\n");
+		ret = -ENODEV;
+		goto unmap_ramc;
+	}
 
 	if (!standby) {
 		pr_warn("ramc no standby function available\n");
-		return;
+		return 0;
 	}
 
 	at91_cpuidle_device.dev.platform_data = standby;
+
+	return 0;
+
+unmap_ramc:
+	while (idx)
+		iounmap(soc_pm.data.ramc[--idx]);
+
+	return ret;
 }
 
 static void at91rm9200_idle(void)
@@ -1017,6 +1080,8 @@ static void __init at91_pm_init(void (*pm_idle)(void))
 
 void __init at91rm9200_pm_init(void)
 {
+	int ret;
+
 	if (!IS_ENABLED(CONFIG_SOC_AT91RM9200))
 		return;
 
@@ -1028,7 +1093,9 @@ void __init at91rm9200_pm_init(void)
 	soc_pm.data.standby_mode = AT91_PM_STANDBY;
 	soc_pm.data.suspend_mode = AT91_PM_ULP0;
 
-	at91_dt_ramc(false);
+	ret = at91_dt_ramc(false);
+	if (ret)
+		return;
 
 	/*
 	 * AT91RM9200 SDRAM low-power mode cannot be used with self-refresh.
@@ -1046,13 +1113,17 @@ void __init sam9x60_pm_init(void)
 	static const int iomaps[] __initconst = {
 		[AT91_PM_ULP1]		= AT91_PM_IOMAP(SHDWC),
 	};
+	int ret;
 
 	if (!IS_ENABLED(CONFIG_SOC_SAM9X60))
 		return;
 
 	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
 	at91_pm_modes_init(iomaps, ARRAY_SIZE(iomaps));
-	at91_dt_ramc(false);
+	ret = at91_dt_ramc(false);
+	if (ret)
+		return;
+
 	at91_pm_init(NULL);
 
 	soc_pm.ws_ids = sam9x60_ws_ids;
@@ -1061,6 +1132,8 @@ void __init sam9x60_pm_init(void)
 
 void __init at91sam9_pm_init(void)
 {
+	int ret;
+
 	if (!IS_ENABLED(CONFIG_SOC_AT91SAM9))
 		return;
 
@@ -1072,7 +1145,10 @@ void __init at91sam9_pm_init(void)
 	soc_pm.data.standby_mode = AT91_PM_STANDBY;
 	soc_pm.data.suspend_mode = AT91_PM_ULP0;
 
-	at91_dt_ramc(false);
+	ret = at91_dt_ramc(false);
+	if (ret)
+		return;
+
 	at91_pm_init(at91sam9_idle);
 }
 
@@ -1081,12 +1157,16 @@ void __init sama5_pm_init(void)
 	static const int modes[] __initconst = {
 		AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST,
 	};
+	int ret;
 
 	if (!IS_ENABLED(CONFIG_SOC_SAMA5))
 		return;
 
 	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
-	at91_dt_ramc(false);
+	ret = at91_dt_ramc(false);
+	if (ret)
+		return;
+
 	at91_pm_init(NULL);
 }
 
@@ -1101,18 +1181,27 @@ void __init sama5d2_pm_init(void)
 		[AT91_PM_BACKUP]	= AT91_PM_IOMAP(SHDWC) |
 					  AT91_PM_IOMAP(SFRBU),
 	};
+	int ret;
 
 	if (!IS_ENABLED(CONFIG_SOC_SAMA5D2))
 		return;
 
 	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
 	at91_pm_modes_init(iomaps, ARRAY_SIZE(iomaps));
-	at91_dt_ramc(false);
+	ret = at91_dt_ramc(false);
+	if (ret)
+		return;
+
 	at91_pm_init(NULL);
 
 	soc_pm.ws_ids = sama5d2_ws_ids;
 	soc_pm.config_shdwc_ws = at91_sama5d2_config_shdwc_ws;
 	soc_pm.config_pmc_ws = at91_sama5d2_config_pmc_ws;
+
+	soc_pm.sfrbu_regs.pswbu.key = (0x4BD20C << 8);
+	soc_pm.sfrbu_regs.pswbu.ctrl = BIT(0);
+	soc_pm.sfrbu_regs.pswbu.softsw = BIT(1);
+	soc_pm.sfrbu_regs.pswbu.state = BIT(3);
 }
 
 void __init sama7_pm_init(void)
@@ -1127,18 +1216,27 @@ void __init sama7_pm_init(void)
 		[AT91_PM_BACKUP]	= AT91_PM_IOMAP(SFRBU) |
 					  AT91_PM_IOMAP(SHDWC),
 	};
+	int ret;
 
 	if (!IS_ENABLED(CONFIG_SOC_SAMA7))
 		return;
 
 	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
 
-	at91_dt_ramc(true);
+	ret = at91_dt_ramc(true);
+	if (ret)
+		return;
+
 	at91_pm_modes_init(iomaps, ARRAY_SIZE(iomaps));
 	at91_pm_init(NULL);
 
 	soc_pm.ws_ids = sama7g5_ws_ids;
 	soc_pm.config_pmc_ws = at91_sam9x60_config_pmc_ws;
+
+	soc_pm.sfrbu_regs.pswbu.key = (0x4BD20C << 8);
+	soc_pm.sfrbu_regs.pswbu.ctrl = BIT(0);
+	soc_pm.sfrbu_regs.pswbu.softsw = BIT(1);
+	soc_pm.sfrbu_regs.pswbu.state = BIT(2);
 }
 
 static int __init at91_pm_modes_select(char *str)

arch/arm/mach-at91/pm_suspend.S

@@ -1014,31 +1014,55 @@ ENTRY(at91_pm_suspend_in_sram)
 	mov	tmp1, #0
 	mcr	p15, 0, tmp1, c7, c10, 4
 
+	/* Flush tlb. */
+	mov	r4, #0
+	mcr	p15, 0, r4, c8, c7, 0
+
+	ldr	tmp1, [r0, #PM_DATA_PMC_MCKR_OFFSET]
+	str	tmp1, .mckr_offset
+	ldr	tmp1, [r0, #PM_DATA_PMC_VERSION]
+	str	tmp1, .pmc_version
+	ldr	tmp1, [r0, #PM_DATA_MEMCTRL]
+	str	tmp1, .memtype
+	ldr	tmp1, [r0, #PM_DATA_MODE]
+	str	tmp1, .pm_mode
+
+	/*
+	 * ldrne below are here to preload their address in the TLB as access
+	 * to RAM may be limited while in self-refresh.
+	 */
 	ldr	tmp1, [r0, #PM_DATA_PMC]
 	str	tmp1, .pmc_base
+	cmp	tmp1, #0
+	ldrne	tmp2, [tmp1, #0]
+
 	ldr	tmp1, [r0, #PM_DATA_RAMC0]
 	str	tmp1, .sramc_base
+	cmp	tmp1, #0
+	ldrne	tmp2, [tmp1, #0]
+
 	ldr	tmp1, [r0, #PM_DATA_RAMC1]
 	str	tmp1, .sramc1_base
+	cmp	tmp1, #0
+	ldrne	tmp2, [tmp1, #0]
+
+#ifndef CONFIG_SOC_SAM_V4_V5
+	/* ldrne below are here to preload their address in the TLB */
 	ldr	tmp1, [r0, #PM_DATA_RAMC_PHY]
 	str	tmp1, .sramc_phy_base
-	ldr	tmp1, [r0, #PM_DATA_MEMCTRL]
-	str	tmp1, .memtype
-	ldr	tmp1, [r0, #PM_DATA_MODE]
-	str	tmp1, .pm_mode
-	ldr	tmp1, [r0, #PM_DATA_PMC_MCKR_OFFSET]
-	str	tmp1, .mckr_offset
-	ldr	tmp1, [r0, #PM_DATA_PMC_VERSION]
-	str	tmp1, .pmc_version
-	/* Both ldrne below are here to preload their address in the TLB */
+	cmp	tmp1, #0
+	ldrne	tmp2, [tmp1, #0]
+
 	ldr	tmp1, [r0, #PM_DATA_SHDWC]
 	str	tmp1, .shdwc
 	cmp	tmp1, #0
 	ldrne	tmp2, [tmp1, #0]
+
 	ldr	tmp1, [r0, #PM_DATA_SFRBU]
 	str	tmp1, .sfrbu
 	cmp	tmp1, #0
 	ldrne	tmp2, [tmp1, #0x10]
+#endif
 
 	/* Active the self-refresh mode */
 	at91_sramc_self_refresh_ena

arch/arm/mach-dove/include/mach/uncompress.h

@@ -11,7 +11,7 @@
 
 #define LSR_THRE	0x20
 
-static void putc(const char c)
+static inline void putc(const char c)
 {
 	int i;
 
@@ -24,7 +24,7 @@ static void putc(const char c)
 	*UART_THR = c;
 }
 
-static void flush(void)
+static inline void flush(void)
 {
 }
 

arch/arm/mach-imx/mach-imx6q.c

@@ -172,6 +172,9 @@ static void __init imx6q_init_machine(void)
 				imx_get_soc_revision());
 
 	imx6q_enet_phy_init();
+
+	of_platform_default_populate(NULL, NULL, NULL);
+
 	imx_anatop_init();
 	cpu_is_imx6q() ?  imx6q_pm_init() : imx6dl_pm_init();
 	imx6q_1588_init();

arch/arm/mach-imx/pm-imx6.c

@@ -10,6 +10,7 @@
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/genalloc.h>
+#include <linux/irqchip/arm-gic.h>
 #include <linux/mfd/syscon.h>
 #include <linux/mfd/syscon/imx6q-iomuxc-gpr.h>
 #include <linux/of.h>
@@ -619,6 +620,7 @@ static void __init imx6_pm_common_init(const struct imx6_pm_socdata
 
 static void imx6_pm_stby_poweroff(void)
 {
+	gic_cpu_if_down(0);
 	imx6_set_lpm(STOP_POWER_OFF);
 	imx6q_suspend_finish(0);
 

arch/arm/mach-omap1/include/mach/memory.h

@@ -9,16 +9,4 @@
 /* REVISIT: omap1 legacy drivers still rely on this */
 #include <mach/soc.h>
 
-/*
- * Bus address is physical address, except for OMAP-1510 Local Bus.
- * OMAP-1510 bus address is translated into a Local Bus address if the
- * OMAP bus type is lbus. We do the address translation based on the
- * device overriding the defaults used in the dma-mapping API.
- */
-
-/*
- * OMAP-1510 Local Bus address offset
- */
-#define OMAP1510_LB_OFFSET	UL(0x30000000)
-
 #endif

arch/arm/mach-omap1/usb.c

@@ -11,6 +11,7 @@
 #include <linux/platform_device.h>
 #include <linux/dma-map-ops.h>
 #include <linux/io.h>
+#include <linux/delay.h>
 
 #include <asm/irq.h>
 
@@ -206,8 +207,6 @@ static inline void udc_device_init(struct omap_usb_config *pdata)
 
 #endif
 
-#if	IS_ENABLED(CONFIG_USB_OHCI_HCD)
-
 /* The dmamask must be set for OHCI to work */
 static u64 ohci_dmamask = ~(u32)0;
 
@@ -236,20 +235,15 @@ static struct platform_device ohci_device = {
 
 static inline void ohci_device_init(struct omap_usb_config *pdata)
 {
+	if (!IS_ENABLED(CONFIG_USB_OHCI_HCD))
+		return;
+
 	if (cpu_is_omap7xx())
 		ohci_resources[1].start = INT_7XX_USB_HHC_1;
 	pdata->ohci_device = &ohci_device;
 	pdata->ocpi_enable = &ocpi_enable;
 }
 
-#else
-
-static inline void ohci_device_init(struct omap_usb_config *pdata)
-{
-}
-
-#endif
-
 #if	defined(CONFIG_USB_OTG) && defined(CONFIG_ARCH_OMAP_OTG)
 
 static struct resource otg_resources[] = {
@@ -534,33 +528,87 @@ static u32 __init omap1_usb2_init(unsigned nwires, unsigned alt_pingroup)
 }
 
 #ifdef	CONFIG_ARCH_OMAP15XX
+/* OMAP-1510 OHCI has its own MMU for DMA */
+#define OMAP1510_LB_MEMSIZE	32	/* Should be same as SDRAM size */
+#define OMAP1510_LB_CLOCK_DIV	0xfffec10c
+#define OMAP1510_LB_MMU_CTL	0xfffec208
+#define OMAP1510_LB_MMU_LCK	0xfffec224
+#define OMAP1510_LB_MMU_LD_TLB	0xfffec228
+#define OMAP1510_LB_MMU_CAM_H	0xfffec22c
+#define OMAP1510_LB_MMU_CAM_L	0xfffec230
+#define OMAP1510_LB_MMU_RAM_H	0xfffec234
+#define OMAP1510_LB_MMU_RAM_L	0xfffec238
 
-/* ULPD_DPLL_CTRL */
-#define DPLL_IOB		(1 << 13)
-#define DPLL_PLL_ENABLE		(1 << 4)
-#define DPLL_LOCK		(1 << 0)
+/*
+ * Bus address is physical address, except for OMAP-1510 Local Bus.
+ * OMAP-1510 bus address is translated into a Local Bus address if the
+ * OMAP bus type is lbus.
+ */
+#define OMAP1510_LB_OFFSET	   UL(0x30000000)
 
-/* ULPD_APLL_CTRL */
-#define APLL_NDPLL_SWITCH	(1 << 0)
+/*
+ * OMAP-1510 specific Local Bus clock on/off
+ */
+static int omap_1510_local_bus_power(int on)
+{
+	if (on) {
+		omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
+		udelay(200);
+	} else {
+		omap_writel(0, OMAP1510_LB_MMU_CTL);
+	}
 
-static int omap_1510_usb_ohci_notifier(struct notifier_block *nb,
-		unsigned long event, void *data)
+	return 0;
+}
+
+/*
+ * OMAP-1510 specific Local Bus initialization
+ * NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
+ *       See also arch/mach-omap/memory.h for __virt_to_dma() and
+ *       __dma_to_virt() which need to match with the physical
+ *       Local Bus address below.
+ */
+static int omap_1510_local_bus_init(void)
 {
-	struct device *dev = data;
+	unsigned int tlb;
+	unsigned long lbaddr, physaddr;
+
+	omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
+	       OMAP1510_LB_CLOCK_DIV);
+
+	/* Configure the Local Bus MMU table */
+	for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
+		lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
+		physaddr = tlb * 0x00100000 + PHYS_OFFSET;
+		omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
+		omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
+		       OMAP1510_LB_MMU_CAM_L);
+		omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
+		omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
+		omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
+		omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
+	}
 
-	if (event != BUS_NOTIFY_ADD_DEVICE)
-		return NOTIFY_DONE;
+	/* Enable the walking table */
+	omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
+	udelay(200);
 
-	if (strncmp(dev_name(dev), "ohci", 4) == 0 &&
-	    dma_direct_set_offset(dev, PHYS_OFFSET, OMAP1510_LB_OFFSET,
-			(u64)-1))
-		WARN_ONCE(1, "failed to set DMA offset\n");
-	return NOTIFY_OK;
+	return 0;
 }
 
-static struct notifier_block omap_1510_usb_ohci_nb = {
-	.notifier_call		= omap_1510_usb_ohci_notifier,
-};
+static void omap_1510_local_bus_reset(void)
+{
+	omap_1510_local_bus_power(1);
+	omap_1510_local_bus_init();
+}
+
+/* ULPD_DPLL_CTRL */
+#define DPLL_IOB		(1 << 13)
+#define DPLL_PLL_ENABLE		(1 << 4)
+#define DPLL_LOCK		(1 << 0)
+
+/* ULPD_APLL_CTRL */
+#define APLL_NDPLL_SWITCH	(1 << 0)
 
 static void __init omap_1510_usb_init(struct omap_usb_config *config)
 {
@@ -616,19 +664,19 @@ static void __init omap_1510_usb_init(struct omap_usb_config *config)
 	}
 #endif
 
-#if	IS_ENABLED(CONFIG_USB_OHCI_HCD)
-	if (config->register_host) {
+	if (IS_ENABLED(CONFIG_USB_OHCI_HCD) && config->register_host) {
 		int status;
 
-		bus_register_notifier(&platform_bus_type,
-				      &omap_1510_usb_ohci_nb);
 		ohci_device.dev.platform_data = config;
+		dma_direct_set_offset(&ohci_device.dev, PHYS_OFFSET,
+				      OMAP1510_LB_OFFSET, (u64)-1);
 		status = platform_device_register(&ohci_device);
 		if (status)
 			pr_debug("can't register OHCI device, %d\n", status);
 		/* hcd explicitly gates 48MHz */
+
+		config->lb_reset = omap_1510_local_bus_reset;
 	}
-#endif
 }
 
 #else

arch/arm/mach-omap2/omap_hwmod.c

@@ -3614,6 +3614,8 @@ int omap_hwmod_init_module(struct device *dev,
 		oh->flags |= HWMOD_SWSUP_SIDLE_ACT;
 	if (data->cfg->quirks & SYSC_QUIRK_SWSUP_MSTANDBY)
 		oh->flags |= HWMOD_SWSUP_MSTANDBY;
+	if (data->cfg->quirks & SYSC_QUIRK_CLKDM_NOAUTO)
+		oh->flags |= HWMOD_CLKDM_NOAUTO;
 
 	error = omap_hwmod_check_module(dev, oh, data, sysc_fields,
 					rev_offs, sysc_offs, syss_offs,

arch/arm64/boot/dts/arm/foundation-v8.dtsi

@@ -115,7 +115,6 @@ v2m_refclk32khz: refclk32khz {
 
 	bus@8000000 {
 		compatible = "arm,vexpress,v2m-p1", "simple-bus";
-		arm,v2m-memory-map = "rs1";
 		#address-cells = <2>; /* SMB chipselect number and offset */
 		#size-cells = <1>;
 

arch/arm64/boot/dts/arm/fvp-base-revc.dts

@@ -192,32 +192,9 @@ panel_in: endpoint {
 				remote-endpoint = <&clcd_pads>;
 			};
 		};
-
-	       panel-timing {
-		       clock-frequency = <63500127>;
-		       hactive = <1024>;
-		       hback-porch = <152>;
-		       hfront-porch = <48>;
-		       hsync-len = <104>;
-		       vactive = <768>;
-		       vback-porch = <23>;
-		       vfront-porch = <3>;
-		       vsync-len = <4>;
-	       };
 	};
 
 	bus@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 63>;
 		interrupt-map = <0 0  0 &gic 0 0 GIC_SPI  0 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/arm/juno-base.dtsi

@@ -27,8 +27,6 @@ mailbox: mhu@2b1f0000 {
 		reg = <0x0 0x2b1f0000 0x0 0x1000>;
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "mhu_lpri_rx",
-				  "mhu_hpri_rx";
 		#mbox-cells = <1>;
 		clocks = <&soc_refclk100mhz>;
 		clock-names = "apb_pclk";
@@ -804,16 +802,6 @@ memory@80000000 {
 	};
 
 	bus@8000000 {
-		compatible = "simple-bus";
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 15>;
 		interrupt-map = <0 0  0 &gic 0 GIC_SPI  68 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/arm/juno-motherboard.dtsi

@@ -92,16 +92,23 @@ nmi-button {
 	};
 
 	bus@8000000 {
-		motherboard-bus {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0x8000000 0 0x8000000 0x18000000>;
+
+		motherboard-bus@8000000 {
 			compatible = "arm,vexpress,v2p-p1", "simple-bus";
 			#address-cells = <2>;  /* SMB chipselect number and offset */
 			#size-cells = <1>;
-			#interrupt-cells = <1>;
-			ranges;
-			model = "V2M-Juno";
+			ranges = <0 0 0 0x08000000 0x04000000>,
+				 <1 0 0 0x14000000 0x04000000>,
+				 <2 0 0 0x18000000 0x04000000>,
+				 <3 0 0 0x1c000000 0x04000000>,
+				 <4 0 0 0x0c000000 0x04000000>,
+				 <5 0 0 0x10000000 0x04000000>;
 			arm,hbi = <0x252>;
 			arm,vexpress,site = <0>;
-			arm,v2m-memory-map = "rs1";
 
 			flash@0 {
 				/* 2 * 32MiB NOR Flash memory mounted on CS0 */
@@ -218,7 +225,7 @@ led7 {
 					};
 				};
 
-				mmci@50000 {
+				mmc@50000 {
 					compatible = "arm,pl180", "arm,primecell";
 					reg = <0x050000 0x1000>;
 					interrupts = <5>;
@@ -246,7 +253,7 @@ kmi@70000 {
 					clock-names = "KMIREFCLK", "apb_pclk";
 				};
 
-				wdt@f0000 {
+				watchdog@f0000 {
 					compatible = "arm,sp805", "arm,primecell";
 					reg = <0x0f0000 0x10000>;
 					interrupts = <7>;

arch/arm64/boot/dts/arm/rtsm_ve-aemv8a.dts

@@ -133,17 +133,6 @@ panel_in: endpoint {
 	};
 
 	bus@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 63>;
 		interrupt-map = <0 0  0 &gic GIC_SPI  0 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/arm/rtsm_ve-motherboard-rs2.dtsi

@@ -6,7 +6,7 @@
  */
 / {
 	bus@8000000 {
-		motherboard-bus {
+		motherboard-bus@8000000 {
 			arm,v2m-memory-map = "rs2";
 
 			iofpga-bus@300000000 {

arch/arm64/boot/dts/arm/rtsm_ve-motherboard.dtsi

@@ -77,13 +77,21 @@ dvimode {
 	};
 
 	bus@8000000 {
-		motherboard-bus {
-			arm,v2m-memory-map = "rs1";
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0x8000000 0 0x8000000 0x18000000>;
+
+		motherboard-bus@8000000 {
 			compatible = "arm,vexpress,v2m-p1", "simple-bus";
 			#address-cells = <2>; /* SMB chipselect number and offset */
 			#size-cells = <1>;
-			#interrupt-cells = <1>;
-			ranges;
+			ranges = <0 0 0 0x08000000 0x04000000>,
+				 <1 0 0 0x14000000 0x04000000>,
+				 <2 0 0 0x18000000 0x04000000>,
+				 <3 0 0 0x1c000000 0x04000000>,
+				 <4 0 0 0x0c000000 0x04000000>,
+				 <5 0 0 0x10000000 0x04000000>;
 
 			flash@0 {
 				compatible = "arm,vexpress-flash", "cfi-flash";
@@ -130,7 +138,7 @@ aaci@40000 {
 					clock-names = "apb_pclk";
 				};
 
-				mmci@50000 {
+				mmc@50000 {
 					compatible = "arm,pl180", "arm,primecell";
 					reg = <0x050000 0x1000>;
 					interrupts = <9>, <10>;
@@ -190,7 +198,7 @@ v2m_serial3: serial@c0000 {
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				wdt@f0000 {
+				watchdog@f0000 {
 					compatible = "arm,sp805", "arm,primecell";
 					reg = <0x0f0000 0x1000>;
 					interrupts = <0>;

arch/arm64/boot/dts/arm/vexpress-v2f-1xv7-ca53x2.dts

@@ -145,61 +145,6 @@ temp-fpga {
 	};
 
 	smb: bus@8000000 {
-		compatible = "simple-bus";
-
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0 0x08000000 0x04000000>,
-			 <1 0 0 0x14000000 0x04000000>,
-			 <2 0 0 0x18000000 0x04000000>,
-			 <3 0 0 0x1c000000 0x04000000>,
-			 <4 0 0 0x0c000000 0x04000000>,
-			 <5 0 0 0x10000000 0x04000000>;
-
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 63>;
-		interrupt-map = <0 0  0 &gic GIC_SPI  0 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  1 &gic GIC_SPI  1 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  2 &gic GIC_SPI  2 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  3 &gic GIC_SPI  3 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  4 &gic GIC_SPI  4 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  5 &gic GIC_SPI  5 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  6 &gic GIC_SPI  6 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  7 &gic GIC_SPI  7 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  8 &gic GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0  9 &gic GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 10 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 11 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 12 &gic GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 13 &gic GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 14 &gic GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 15 &gic GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 16 &gic GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 17 &gic GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 18 &gic GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 19 &gic GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 20 &gic GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 21 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 22 &gic GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 23 &gic GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 24 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 25 &gic GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 26 &gic GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 27 &gic GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 28 &gic GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 29 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 30 &gic GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 31 &gic GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 32 &gic GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 33 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 34 &gic GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 35 &gic GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 36 &gic GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 37 &gic GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 38 &gic GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 39 &gic GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 40 &gic GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 41 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 42 &gic GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+		ranges = <0x8000000 0 0x8000000 0x18000000>;
 	};
 };

arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi

@@ -405,9 +405,9 @@ esdhc1: mmc@2150000 {
 			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <0>; /* fixed up by bootloader */
 			clocks = <&clockgen QORIQ_CLK_HWACCEL 1>;
-			voltage-ranges = <1800 1800 3300 3300>;
+			voltage-ranges = <1800 1800>;
 			sdhci,auto-cmd12;
-			broken-cd;
+			non-removable;
 			little-endian;
 			bus-width = <4>;
 			status = "disabled";

arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi

@@ -91,7 +91,7 @@ flash@0 {
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };

arch/arm64/boot/dts/freescale/imx8mm-evk.dts

@@ -48,7 +48,7 @@ flash@0 {
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };

arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi

@@ -102,6 +102,7 @@ reg_vdd_arm: BUCK2 {
 				regulator-min-microvolt = <850000>;
 				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
+				regulator-always-on;
 				regulator-ramp-delay = <3125>;
 				nxp,dvs-run-voltage = <950000>;
 				nxp,dvs-standby-voltage = <850000>;

arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts

@@ -647,7 +647,7 @@ &iomuxc {
 	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1	0x40000159 /* M2_GDIS# */
-			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x40000041 /* M2_RST# */
+			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x40000041 /* M2_RST# */
 			MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7	0x40000119 /* M2_OFF# */
 			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x40000159 /* M2_WDIS# */
 			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14	0x40000041 /* AMP GPIO1 */

arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi

@@ -101,7 +101,7 @@ flash@0 {
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };

arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts

@@ -633,7 +633,7 @@ &iomuxc {
 	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_NAND_CE0_B_GPIO3_IO1	0x40000159 /* M2_GDIS# */
-			MX8MN_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x40000041 /* M2_RST# */
+			MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x40000041 /* M2_RST# */
 			MX8MN_IOMUXC_NAND_DATA01_GPIO3_IO7	0x40000119 /* M2_OFF# */
 			MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x40000159 /* M2_WDIS# */
 			MX8MN_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x40000041 /* APP GPIO1 */

arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi

@@ -74,7 +74,7 @@ som_flash: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };

arch/arm64/boot/dts/freescale/imx8mq-evk.dts

@@ -337,6 +337,8 @@ n25q256a: flash@0 {
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
 	};
 };
 

arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts

@@ -281,7 +281,7 @@ flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 		m25p,fast-read;
 		spi-max-frequency = <50000000>;

arch/arm64/boot/dts/qcom/pm8150.dtsi

@@ -48,8 +48,10 @@ pm8150_0: pmic@0 {
 		#size-cells = <0>;
 
 		pon: power-on@800 {
-			compatible = "qcom,pm8916-pon";
+			compatible = "qcom,pm8998-pon";
 			reg = <0x0800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
 
 			pon_pwrkey: pwrkey {
 				compatible = "qcom,pm8941-pwrkey";

arch/arm64/boot/dts/qcom/qrb5165-rb5.dts

@@ -804,6 +804,16 @@ lt9611_rst_pin: lt9611-rst-pin {
 	};
 };
 
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi

@@ -273,7 +273,6 @@ sound: sound {
 			"Headphone Jack", "HPOL",
 			"Headphone Jack", "HPOR";
 
-		#sound-dai-cells = <0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
@@ -301,11 +300,11 @@ sound_multimedia1_codec: codec {
 			};
 		};
 
-		dai-link@2 {
+		dai-link@5 {
 			link-name = "MultiMedia2";
-			reg = <2>;
+			reg = <LPASS_DP_RX>;
 			cpu {
-				sound-dai = <&lpass_cpu 2>;
+				sound-dai = <&lpass_cpu LPASS_DP_RX>;
 			};
 
 			codec {
@@ -782,7 +781,7 @@ secondary_mi2s: mi2s@1 {
 		qcom,playback-sd-lines = <0>;
 	};
 
-	hdmi-primary@0 {
+	hdmi@5 {
 		reg = <LPASS_DP_RX>;
 	};
 };

arch/arm64/boot/dts/qcom/sc7280.dtsi

@@ -1850,9 +1850,9 @@ rpmhcc: clock-controller {
 
 		cpufreq_hw: cpufreq@18591000 {
 			compatible = "qcom,cpufreq-epss";
-			reg = <0 0x18591100 0 0x900>,
-			      <0 0x18592100 0 0x900>,
-			      <0 0x18593100 0 0x900>;
+			reg = <0 0x18591000 0 0x1000>,
+			      <0 0x18592000 0 0x1000>,
+			      <0 0x18593000 0 0x1000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
 			clock-names = "xo", "alternate";
 			#freq-domain-cells = <1>;

arch/arm64/boot/dts/qcom/sdm630.dtsi

@@ -654,9 +654,20 @@ a2noc: interconnect@1704000 {
 			compatible = "qcom,sdm660-a2noc";
 			reg = <0x01704000 0xc100>;
 			#interconnect-cells = <1>;
-			clock-names = "bus", "bus_a";
+			clock-names = "bus",
+				      "bus_a",
+				      "ipa",
+				      "ufs_axi",
+				      "aggre2_ufs_axi",
+				      "aggre2_usb3_axi",
+				      "cfg_noc_usb2_axi";
 			clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>,
-				 <&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>;
+				 <&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>,
+				 <&rpmcc RPM_SMD_IPA_CLK>,
+				 <&gcc GCC_UFS_AXI_CLK>,
+				 <&gcc GCC_AGGRE2_UFS_AXI_CLK>,
+				 <&gcc GCC_AGGRE2_USB3_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_USB2_AXI_CLK>;
 		};
 
 		mnoc: interconnect@1745000 {

arch/arm64/boot/dts/qcom/sdm845.dtsi

@@ -128,23 +128,28 @@ camera_mem: memory@8bf00000 {
 			no-map;
 		};
 
-		wlan_msa_mem: memory@8c400000 {
-			reg = <0 0x8c400000 0 0x100000>;
+		ipa_fw_mem: memory@8c400000 {
+			reg = <0 0x8c400000 0 0x10000>;
 			no-map;
 		};
 
-		gpu_mem: memory@8c515000 {
-			reg = <0 0x8c515000 0 0x2000>;
+		ipa_gsi_mem: memory@8c410000 {
+			reg = <0 0x8c410000 0 0x5000>;
 			no-map;
 		};
 
-		ipa_fw_mem: memory@8c517000 {
-			reg = <0 0x8c517000 0 0x5a000>;
+		gpu_mem: memory@8c415000 {
+			reg = <0 0x8c415000 0 0x2000>;
 			no-map;
 		};
 
-		adsp_mem: memory@8c600000 {
-			reg = <0 0x8c600000 0 0x1a00000>;
+		adsp_mem: memory@8c500000 {
+			reg = <0 0x8c500000 0 0x1a00000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@8df00000 {
+			reg = <0 0x8df00000 0 0x100000>;
 			no-map;
 		};
 

arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts

@@ -16,6 +16,17 @@
 #include "sdm850.dtsi"
 #include "pm8998.dtsi"
 
+/*
+ * Update following upstream (sdm845.dtsi) reserved
+ * memory mappings for firmware loading to succeed
+ * and enable the IPA device.
+ */
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+/delete-node/ &adsp_mem;
+/delete-node/ &wlan_msa_mem;
+
 / {
 	model = "Lenovo Yoga C630";
 	compatible = "lenovo,yoga-c630", "qcom,sdm845";
@@ -58,6 +69,29 @@ panel_in_edp: endpoint {
 		};
 	};
 
+	/* Reserved memory changes for IPA */
+	reserved-memory {
+		wlan_msa_mem: memory@8c400000 {
+			reg = <0 0x8c400000 0 0x100000>;
+			no-map;
+		};
+
+		gpu_mem: memory@8c515000 {
+			reg = <0 0x8c515000 0 0x2000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@8c517000 {
+			reg = <0 0x8c517000 0 0x5a000>;
+			no-map;
+		};
+
+		adsp_mem: memory@8c600000 {
+			reg = <0 0x8c600000 0 0x1a00000>;
+			no-map;
+		};
+	};
+
 	sn65dsi86_refclk: sn65dsi86-refclk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;

drivers/bus/ti-sysc.c

@@ -1464,6 +1464,9 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = {
 	/* Quirks that need to be set based on detected module */
 	SYSC_QUIRK("aess", 0, 0, 0x10, -ENODEV, 0x40000000, 0xffffffff,
 		   SYSC_MODULE_QUIRK_AESS),
+	/* Errata i893 handling for dra7 dcan1 and 2 */
+	SYSC_QUIRK("dcan", 0x4ae3c000, 0x20, -ENODEV, -ENODEV, 0xa3170504, 0xffffffff,
+		   SYSC_QUIRK_CLKDM_NOAUTO),
 	SYSC_QUIRK("dcan", 0x48480000, 0x20, -ENODEV, -ENODEV, 0xa3170504, 0xffffffff,
 		   SYSC_QUIRK_CLKDM_NOAUTO),
 	SYSC_QUIRK("dss", 0x4832a000, 0, 0x10, 0x14, 0x00000020, 0xffffffff,
@@ -2954,6 +2957,7 @@ static int sysc_init_soc(struct sysc *ddata)
 			break;
 		case SOC_AM3:
 			sysc_add_disabled(0x48310000);  /* rng */
+			break;
 		default:
 			break;
 		}

drivers/firmware/Kconfig

@@ -204,7 +204,7 @@ config INTEL_STRATIX10_RSU
 
 config QCOM_SCM
 	tristate "Qcom SCM driver"
-	depends on ARM || ARM64
+	depends on ARCH_QCOM || COMPILE_TEST
 	depends on HAVE_ARM_SMCCC
 	select RESET_CONTROLLER
 

drivers/firmware/arm_scmi/Kconfig

@@ -68,7 +68,7 @@ config ARM_SCMI_TRANSPORT_SMC
 
 config ARM_SCMI_TRANSPORT_VIRTIO
 	bool "SCMI transport based on VirtIO"
-	depends on VIRTIO
+	depends on VIRTIO=y || VIRTIO=ARM_SCMI_PROTOCOL
 	select ARM_SCMI_HAVE_TRANSPORT
 	select ARM_SCMI_HAVE_MSG
 	help

drivers/firmware/arm_scmi/virtio.c

@@ -110,18 +110,16 @@ static void scmi_finalize_message(struct scmi_vio_channel *vioch,
 	if (vioch->is_rx) {
 		scmi_vio_feed_vq_rx(vioch, msg);
 	} else {
-		unsigned long flags;
-
-		spin_lock_irqsave(&vioch->lock, flags);
+		/* Here IRQs are assumed to be already disabled by the caller */
+		spin_lock(&vioch->lock);
 		list_add(&msg->list, &vioch->free_list);
-		spin_unlock_irqrestore(&vioch->lock, flags);
+		spin_unlock(&vioch->lock);
 	}
 }
 
 static void scmi_vio_complete_cb(struct virtqueue *vqueue)
 {
 	unsigned long ready_flags;
-	unsigned long flags;
 	unsigned int length;
 	struct scmi_vio_channel *vioch;
 	struct scmi_vio_msg *msg;
@@ -140,7 +138,8 @@ static void scmi_vio_complete_cb(struct virtqueue *vqueue)
 			goto unlock_ready_out;
 		}
 
-		spin_lock_irqsave(&vioch->lock, flags);
+		/* IRQs already disabled here no need to irqsave */
+		spin_lock(&vioch->lock);
 		if (cb_enabled) {
 			virtqueue_disable_cb(vqueue);
 			cb_enabled = false;
@@ -151,7 +150,7 @@ static void scmi_vio_complete_cb(struct virtqueue *vqueue)
 				goto unlock_out;
 			cb_enabled = true;
 		}
-		spin_unlock_irqrestore(&vioch->lock, flags);
+		spin_unlock(&vioch->lock);
 
 		if (msg) {
 			msg->rx_len = length;
@@ -161,11 +160,18 @@ static void scmi_vio_complete_cb(struct virtqueue *vqueue)
 			scmi_finalize_message(vioch, msg);
 		}
 
+		/*
+		 * Release ready_lock and re-enable IRQs between loop iterations
+		 * to allow virtio_chan_free() to possibly kick in and set the
+		 * flag vioch->ready to false even in between processing of
+		 * messages, so as to force outstanding messages to be ignored
+		 * when system is shutting down.
+		 */
 		spin_unlock_irqrestore(&vioch->ready_lock, ready_flags);
 	}
 
 unlock_out:
-	spin_unlock_irqrestore(&vioch->lock, flags);
+	spin_unlock(&vioch->lock);
 unlock_ready_out:
 	spin_unlock_irqrestore(&vioch->ready_lock, ready_flags);
 }
@@ -384,8 +390,11 @@ static int scmi_vio_probe(struct virtio_device *vdev)
 	struct virtqueue *vqs[VIRTIO_SCMI_VQ_MAX_CNT];
 
 	/* Only one SCMI VirtiO device allowed */
-	if (scmi_vdev)
-		return -EINVAL;
+	if (scmi_vdev) {
+		dev_err(dev,
+			"One SCMI Virtio device was already initialized: only one allowed.\n");
+		return -EBUSY;
+	}
 
 	have_vq_rx = scmi_vio_have_vq_rx(vdev);
 	vq_cnt = have_vq_rx ? VIRTIO_SCMI_VQ_MAX_CNT : 1;
@@ -428,16 +437,25 @@ static int scmi_vio_probe(struct virtio_device *vdev)
 	}
 
 	vdev->priv = channels;
-	scmi_vdev = vdev;
+	/* Ensure initialized scmi_vdev is visible */
+	smp_store_mb(scmi_vdev, vdev);
 
 	return 0;
 }
 
 static void scmi_vio_remove(struct virtio_device *vdev)
 {
+	/*
+	 * Once we get here, virtio_chan_free() will have already been called by
+	 * the SCMI core for any existing channel and, as a consequence, all the
+	 * virtio channels will have been already marked NOT ready, causing any
+	 * outstanding message on any vqueue to be ignored by complete_cb: now
+	 * we can just stop processing buffers and destroy the vqueues.
+	 */
 	vdev->config->reset(vdev);
 	vdev->config->del_vqs(vdev);
-	scmi_vdev = NULL;
+	/* Ensure scmi_vdev is visible as NULL */
+	smp_store_mb(scmi_vdev, NULL);
 }
 
 static int scmi_vio_validate(struct virtio_device *vdev)
@@ -476,7 +494,7 @@ static int __init virtio_scmi_init(void)
 	return register_virtio_driver(&virtio_scmi_driver);
 }
 
-static void __exit virtio_scmi_exit(void)
+static void virtio_scmi_exit(void)
 {
 	unregister_virtio_driver(&virtio_scmi_driver);
 }

drivers/soc/qcom/mdt_loader.c

@@ -98,7 +98,7 @@ void *qcom_mdt_read_metadata(const struct firmware *fw, size_t *data_len)
 	if (ehdr->e_phnum < 2)
 		return ERR_PTR(-EINVAL);
 
-	if (phdrs[0].p_type == PT_LOAD || phdrs[1].p_type == PT_LOAD)
+	if (phdrs[0].p_type == PT_LOAD)
 		return ERR_PTR(-EINVAL);
 
 	if ((phdrs[1].p_flags & QCOM_MDT_TYPE_MASK) != QCOM_MDT_TYPE_HASH)

drivers/soc/qcom/socinfo.c

@@ -628,7 +628,7 @@ static int qcom_socinfo_probe(struct platform_device *pdev)
 	/* Feed the soc specific unique data into entropy pool */
 	add_device_randomness(info, item_size);
 
-	platform_set_drvdata(pdev, qs->soc_dev);
+	platform_set_drvdata(pdev, qs);
 
 	return 0;
 }

drivers/soc/ti/omap_prm.c

@@ -825,25 +825,28 @@ static int omap_reset_deassert(struct reset_controller_dev *rcdev,
 	writel_relaxed(v, reset->prm->base + reset->prm->data->rstctrl);
 	spin_unlock_irqrestore(&reset->lock, flags);
 
-	if (!has_rstst)
-		goto exit;
+	/* wait for the reset bit to clear */
+	ret = readl_relaxed_poll_timeout_atomic(reset->prm->base +
+						reset->prm->data->rstctrl,
+						v, !(v & BIT(id)), 1,
+						OMAP_RESET_MAX_WAIT);
+	if (ret)
+		pr_err("%s: timedout waiting for %s:%lu\n", __func__,
+		       reset->prm->data->name, id);
 
 	/* wait for the status to be set */
-	ret = readl_relaxed_poll_timeout_atomic(reset->prm->base +
+	if (has_rstst) {
+		ret = readl_relaxed_poll_timeout_atomic(reset->prm->base +
 						 reset->prm->data->rstst,
 						 v, v & BIT(st_bit), 1,
 						 OMAP_RESET_MAX_WAIT);
-	if (ret)
-		pr_err("%s: timedout waiting for %s:%lu\n", __func__,
-		       reset->prm->data->name, id);
+		if (ret)
+			pr_err("%s: timedout waiting for %s:%lu\n", __func__,
+			       reset->prm->data->name, id);
+	}
 
-exit:
-	if (reset->clkdm) {
-		/* At least dra7 iva needs a delay before clkdm idle */
-		if (has_rstst)
-			udelay(1);
+	if (reset->clkdm)
 		pdata->clkdm_allow_idle(reset->clkdm);
-	}
 
 	return ret;
 }

drivers/tee/optee/shm_pool.c

@@ -35,7 +35,7 @@ static int pool_op_alloc(struct tee_shm_pool_mgr *poolm,
 		unsigned int nr_pages = 1 << order, i;
 		struct page **pages;
 
-		pages = kcalloc(nr_pages, sizeof(pages), GFP_KERNEL);
+		pages = kcalloc(nr_pages, sizeof(*pages), GFP_KERNEL);
 		if (!pages) {
 			rc = -ENOMEM;
 			goto err;

drivers/usb/host/ohci-omap.c

@@ -40,17 +40,6 @@
 #include <mach/usb.h>
 
 
-/* OMAP-1510 OHCI has its own MMU for DMA */
-#define OMAP1510_LB_MEMSIZE	32	/* Should be same as SDRAM size */
-#define OMAP1510_LB_CLOCK_DIV	0xfffec10c
-#define OMAP1510_LB_MMU_CTL	0xfffec208
-#define OMAP1510_LB_MMU_LCK	0xfffec224
-#define OMAP1510_LB_MMU_LD_TLB	0xfffec228
-#define OMAP1510_LB_MMU_CAM_H	0xfffec22c
-#define OMAP1510_LB_MMU_CAM_L	0xfffec230
-#define OMAP1510_LB_MMU_RAM_H	0xfffec234
-#define OMAP1510_LB_MMU_RAM_L	0xfffec238
-
 #define DRIVER_DESC "OHCI OMAP driver"
 
 struct ohci_omap_priv {
@@ -104,61 +93,6 @@ static int omap_ohci_transceiver_power(struct ohci_omap_priv *priv, int on)
 	return 0;
 }
 
-#ifdef CONFIG_ARCH_OMAP15XX
-/*
- * OMAP-1510 specific Local Bus clock on/off
- */
-static int omap_1510_local_bus_power(int on)
-{
-	if (on) {
-		omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
-		udelay(200);
-	} else {
-		omap_writel(0, OMAP1510_LB_MMU_CTL);
-	}
-
-	return 0;
-}
-
-/*
- * OMAP-1510 specific Local Bus initialization
- * NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
- *       See also arch/mach-omap/memory.h for __virt_to_dma() and
- *       __dma_to_virt() which need to match with the physical
- *       Local Bus address below.
- */
-static int omap_1510_local_bus_init(void)
-{
-	unsigned int tlb;
-	unsigned long lbaddr, physaddr;
-
-	omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
-	       OMAP1510_LB_CLOCK_DIV);
-
-	/* Configure the Local Bus MMU table */
-	for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
-		lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
-		physaddr = tlb * 0x00100000 + PHYS_OFFSET;
-		omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
-		omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
-		       OMAP1510_LB_MMU_CAM_L);
-		omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
-		omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
-		omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
-		omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
-	}
-
-	/* Enable the walking table */
-	omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
-	udelay(200);
-
-	return 0;
-}
-#else
-#define omap_1510_local_bus_power(x)	{}
-#define omap_1510_local_bus_init()	{}
-#endif
-
 #ifdef	CONFIG_USB_OTG
 
 static void start_hnp(struct ohci_hcd *ohci)
@@ -229,10 +163,8 @@ static int ohci_omap_reset(struct usb_hcd *hcd)
 
 	omap_ohci_clock_power(priv, 1);
 
-	if (cpu_is_omap15xx()) {
-		omap_1510_local_bus_power(1);
-		omap_1510_local_bus_init();
-	}
+	if (config->lb_reset)
+		config->lb_reset();
 
 	ret = ohci_setup(hcd);
 	if (ret < 0)

include/linux/platform_data/usb-omap1.h

@@ -48,6 +48,8 @@ struct omap_usb_config {
 	u32 (*usb2_init)(unsigned nwires, unsigned alt_pingroup);
 
 	int (*ocpi_enable)(void);
+
+	void (*lb_reset)(void);
 };
 
 #endif /* __LINUX_USB_OMAP1_H */