Merge tag 'v5.9-rockchip-dts32-1' of...

Merge tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt

Biggest part is the addition of the rk3288 variant of the VMARC
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).

Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.

* tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: Add PCIe for RockPI N10
  ARM: dts: rockchip: Add HDMI out for RockPI N8/N10
  ARM: dts: rockchip: Add USB for RockPI N8/N10
  ARM: dts: rockchip: Add usb host0 ohci node for rk3288
  ARM: dts: rockchip: Fix VBUS on rk3288-vyasa
  ARM: dts: rockchip: Add Radxa Rock Pi N8 initial support
  ARM: dts: rockchip: Add VMARC RK3288 SOM initial support
  dt-bindings: arm: rockchip: Add Rock Pi N8 binding
  arm64: dts: rk3399pro: vmarc-som: Move common properties into Carrier
  arm64: dts: rk3399pro: vmarc-som: Move supply regulators into Carrier
  arm64: dts: rk3399pro: vmarc-som: Fix sorting nodes, properties
  ARM: dts: rockchip: dalang-carrier: Move i2c nodes into SOM
  ARM: dts: rockchip: Add 'arm,pl330-periph-burst' for dmac
  ARM: dts: rockchip: Add marvell BT irq config
  ARM: dts: rockchip: rename label and nodename pinctrl subnodes that end with gpio

Link: https://lore.kernel.org/r/2472314.kD9Egx1jfM@philSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/rockchip.yaml

@@ -435,6 +435,12 @@ properties:
           - const: radxa,rockpi4
           - const: rockchip,rk3399
 
+      - description: Radxa ROCK Pi N8
+        items:
+          - const: radxa,rockpi-n8
+          - const: vamrs,rk3288-vmarc-som
+          - const: rockchip,rk3288
+
       - description: Radxa ROCK Pi N10
         items:
           - const: radxa,rockpi-n10

arch/arm/boot/dts/Makefile

@@ -982,6 +982,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-popmetal.dtb \
 	rk3288-r89.dtb \
 	rk3288-rock2-square.dtb \
+	rk3288-rock-pi-n8.dtb \
 	rk3288-tinker.dtb \
 	rk3288-tinker-s.dtb \
 	rk3288-veyron-brain.dtb \

arch/arm/boot/dts/rk3036.dtsi

@@ -67,6 +67,7 @@ pdma: pdma@20078000 {
 				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMAC2>;
 			clock-names = "apb_pclk";
 		};

arch/arm/boot/dts/rk322x.dtsi

@@ -107,6 +107,7 @@ pdma: pdma@110f0000 {
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMAC>;
 			clock-names = "apb_pclk";
 		};
@@ -520,9 +521,9 @@ tsadc: tsadc@11150000 {
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
 		pinctrl-names = "init", "default", "sleep";
-		pinctrl-0 = <&otp_gpio>;
+		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
-		pinctrl-2 = <&otp_gpio>;
+		pinctrl-2 = <&otp_pin>;
 		#thermal-sensor-cells = <0>;
 		rockchip,hw-tshut-temp = <95000>;
 		status = "disabled";
@@ -1111,7 +1112,7 @@ spdif_tx: spdif-tx {
 		};
 
 		tsadc {
-			otp_gpio: otp-gpio {
+			otp_pin: otp-pin {
 				rockchip,pins = <0 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 

arch/arm/boot/dts/rk3288-rock-pi-n8.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2019 Vamrs Limited
+ * Copyright (c) 2019 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "rk3288.dtsi"
+#include <arm/rockchip-radxa-dalang-carrier.dtsi>
+#include "rk3288-vmarc-som.dtsi"
+
+/ {
+	model = "Radxa ROCK Pi N8";
+	compatible = "radxa,rockpi-n8", "vamrs,rk3288-vmarc-som",
+		     "rockchip,rk3288";
+};

arch/arm/boot/dts/rk3288-veyron-jaq.dts

@@ -44,10 +44,25 @@ regulator-state-mem {
 	};
 };
 
+&sdio0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	btmrvl: btmrvl@2 {
+		compatible = "marvell,sd8897-bt";
+		reg = <2>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <RK_PD7 IRQ_TYPE_LEVEL_LOW>;
+		marvell,wakeup-pin = /bits/ 16 <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l>;
+	};
+};
+
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 

arch/arm/boot/dts/rk3288-veyron-jerry.dts

@@ -192,7 +192,7 @@ mwifiex: wifi@1 {
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 

arch/arm/boot/dts/rk3288-veyron-mighty.dts

@@ -18,8 +18,8 @@ / {
 };
 
 &sdmmc {
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
-			&sdmmc_wp_gpio &sdmmc_bus4>;
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
+			&sdmmc_wp_pin &sdmmc_bus4>;
 	wp-gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>;
 
 	/delete-property/ disable-wp;
@@ -27,7 +27,7 @@ &sdmmc {
 
 &pinctrl {
 	sdmmc {
-		sdmmc_wp_gpio: sdmmc-wp-gpio {
+		sdmmc_wp_pin: sdmmc-wp-pin {
 			rockchip,pins = <7 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};

arch/arm/boot/dts/rk3288-veyron-minnie.dts

@@ -114,7 +114,7 @@ regulator-state-mem {
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 

arch/arm/boot/dts/rk3288-veyron-pinky.dts

@@ -105,7 +105,7 @@ emmc_reset: emmc-reset {
 	};
 
 	sdmmc {
-		sdmmc_wp_gpio: sdmmc-wp-gpio {
+		sdmmc_wp_pin: sdmmc-wp-pin {
 			rockchip,pins = <7 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
@@ -126,8 +126,8 @@ regulator-state-mem {
 
 &sdmmc {
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
-		     &sdmmc_wp_gpio &sdmmc_bus4>;
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
+		     &sdmmc_wp_pin &sdmmc_bus4>;
 	wp-gpios = <&gpio7 RK_PB2 GPIO_ACTIVE_HIGH>;
 };
 

arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi

@@ -41,7 +41,7 @@ sdmmc_cd_disabled: sdmmc-cd-disabled {
 		};
 
 		/* This is where we actually hook up CD */
-		sdmmc_cd_gpio: sdmmc-cd-gpio {
+		sdmmc_cd_pin: sdmmc-cd-pin {
 			rockchip,pins = <7 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};

arch/arm/boot/dts/rk3288-veyron-speedy.dts

@@ -54,7 +54,7 @@ &rk808 {
 &sdmmc {
 	disable-wp;
 	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_pin
 			&sdmmc_bus4>;
 };
 

arch/arm/boot/dts/rk3288-vmarc-som.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2019 Vamrs Limited
+ * Copyright (c) 2019 Amarula Solutions(India)
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+/ {
+	compatible = "vamrs,rk3288-vmarc-som", "rockchip,rk3288";
+
+	vccio_flash: vccio-flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vccio_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vccio_flash>;
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	phy-supply = <&vcc_io>;
+	snps,reset-gpio = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec_c0>;
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc_io>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc5v0_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-name = "vdd_arm";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-ramp-delay = <6000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_tp: LDO_REG1 {
+				regulator-name = "vcc_tp";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_codec: LDO_REG2 {
+				regulator-name = "vcca_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-name = "vdd_10";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_wl: LDO_REG4 {
+				regulator-name = "vcc_wl";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-name = "vdd10_lcd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-name = "vcc_18";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG8 {
+				regulator-name = "vcc18_lcd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_sd: SWITCH_REG1 {
+				regulator-name = "vcc_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-name = "vcc_lcd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&io_domains {
+	bb-supply = <&vcc_io>;
+	flash0-supply = <&vccio_flash>;
+	gpio1830-supply = <&vcc_18>;
+	gpio30-supply = <&vcc_io>;
+	sdcard-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&pinctrl {
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins =
+				<6 RK_PC0 1 &pcfg_pull_up_drv_8ma>,
+				<6 RK_PC1 1 &pcfg_pull_up_drv_8ma>,
+				<6 RK_PC2 1 &pcfg_pull_up_drv_8ma>,
+				<6 RK_PC3 1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 RK_PC4 1 &pcfg_pull_none_drv_8ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 RK_PC5 1 &pcfg_pull_up_drv_8ma>;
+		};
+	};
+
+	vbus_host {
+		usb1_en_oc: usb1-en-oc {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	vbus_typec {
+		usb0_en_oc: usb0-en-oc {
+			rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&vbus_host {
+	enable-active-high;
+	gpio = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>; /* USB1_EN_OC# */
+};
+
+&vbus_typec {
+	enable-active-high;
+	gpio = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>; /* USB0_EN_OC# */
+};

arch/arm/boot/dts/rk3288-vyasa.dts

@@ -99,8 +99,6 @@ vusb1_5v: vusb1-5v {
 		pinctrl-0 = <&otg_vbus_drv>;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		regulator-boot-on;
 		vin-supply = <&vsus_5v>;
 	};
 
@@ -416,6 +414,7 @@ &usb_host1 {
 };
 
 &usb_otg {
+	vbus-supply = <&vusb1_5v>;
 	status = "okay";
 };
 

arch/arm/boot/dts/rk3288.dtsi

@@ -167,6 +167,7 @@ dmac_peri: dma-controller@ff250000 {
 				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMAC2>;
 			clock-names = "apb_pclk";
 		};
@@ -178,6 +179,7 @@ dmac_bus_ns: dma-controller@ff600000 {
 				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMAC1>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -190,6 +192,7 @@ dmac_bus_s: dma-controller@ffb20000 {
 				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMAC1>;
 			clock-names = "apb_pclk";
 		};
@@ -574,9 +577,9 @@ tsadc: tsadc@ff280000 {
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
 		pinctrl-names = "init", "default", "sleep";
-		pinctrl-0 = <&otp_gpio>;
+		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
-		pinctrl-2 = <&otp_gpio>;
+		pinctrl-2 = <&otp_pin>;
 		#thermal-sensor-cells = <1>;
 		rockchip,grf = <&grf>;
 		rockchip,hw-tshut-temp = <95000>;
@@ -613,7 +616,16 @@ usb_host0_ehci: usb@ff500000 {
 		status = "disabled";
 	};
 
-	/* NOTE: ohci@ff520000 doesn't actually work on hardware */
+	/* NOTE: doesn't work on RK3288, but was fixed on RK3288W */
+	usb_host0_ohci: usb@ff520000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xff520000 0x0 0x100>;
+		interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_USBHOST0>;
+		phys = <&usbphy1>;
+		phy-names = "usb";
+		status = "disabled";
+	};
 
 	usb_host1: usb@ff540000 {
 		compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
@@ -1929,7 +1941,7 @@ uart4_rts: uart4-rts {
 		};
 
 		tsadc {
-			otp_gpio: otp-gpio {
+			otp_pin: otp-pin {
 				rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 

arch/arm/boot/dts/rk3xxx.dtsi

@@ -45,6 +45,7 @@ dmac1_s: dma-controller@20018000 {
 				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMA1>;
 			clock-names = "apb_pclk";
 		};
@@ -56,6 +57,7 @@ dmac1_ns: dma-controller@2001c000 {
 				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMA1>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -68,6 +70,7 @@ dmac2: dma-controller@20078000 {
 				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMA2>;
 			clock-names = "apb_pclk";
 		};

arch/arm/boot/dts/rockchip-radxa-dalang-carrier.dtsi

@@ -8,36 +8,66 @@
 #include <dt-bindings/pwm/pwm.h>
 
 / {
-	chosen {
-		stdout-path = "serial2:1500000n8";
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
 	};
-};
 
-&gmac {
-	status = "okay";
+	vcc12v_dcin: vcc12v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vbus_host: vbus-host {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb1_en_oc>;
+		regulator-name = "vbus_host"; /* HOST-5V */
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vbus_typec: vbus-typec {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_en_oc>;
+		regulator-name = "vbus_typec";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
 };
 
-&i2c1 {
+&gmac {
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x28>;
+	rx_delay = <0x11>;
 	status = "okay";
-	i2c-scl-rising-time-ns = <140>;
-	i2c-scl-falling-time-ns = <30>;
 };
 
-&i2c2 {
+&hdmi {
 	status = "okay";
-	clock-frequency = <400000>;
-
-	hym8563: hym8563@51 {
-		compatible = "haoyu,hym8563";
-		reg = <0x51>;
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-		clock-output-names = "hym8563";
-		pinctrl-names = "default";
-		pinctrl-0 = <&hym8563_int>;
-		interrupt-parent = <&gpio4>;
-		interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
-	};
 };
 
 &pwm0 {
@@ -52,10 +82,8 @@ &sdmmc {
 	bus-width = <4>;
 	cap-mmc-highspeed;
 	cap-sd-highspeed;
-	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	vqmmc-supply = <&vccio_sd>;
-	max-frequency = <150000000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
 	status = "okay";
@@ -71,11 +99,18 @@ &uart2 {
 	status = "okay";
 };
 
-&pinctrl {
-	hym8563 {
-		hym8563_int: hym8563-int {
-			rockchip,pins =
-				<4 RK_PD6 0 &pcfg_pull_up>;
-		};
-	};
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
 };

arch/arm/boot/dts/rv1108.dtsi

@@ -97,6 +97,7 @@ pdma: pdma@102a0000 {
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			arm,pl330-broken-no-flushp;
+			arm,pl330-periph-burst;
 			clocks = <&cru ACLK_DMAC>;
 			clock-names = "apb_pclk";
 		};
@@ -351,9 +352,9 @@ tsadc: tsadc@10370000 {
 		clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
 		clock-names = "tsadc", "apb_pclk";
 		pinctrl-names = "init", "default", "sleep";
-		pinctrl-0 = <&otp_gpio>;
+		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
-		pinctrl-2 = <&otp_gpio>;
+		pinctrl-2 = <&otp_pin>;
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
 		rockchip,hw-tshut-temp = <120000>;
@@ -728,7 +729,7 @@ i2c2m1_xfer: i2c2m1-xfer {
 						<0 RK_PC6 3 &pcfg_pull_none>;
 			};
 
-			i2c2m1_gpio: i2c2m1-gpio {
+			i2c2m1_pins: i2c2m1-pins {
 				rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>,
 						<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
@@ -740,7 +741,7 @@ i2c2m05v_xfer: i2c2m05v-xfer {
 						<1 RK_PD4 2 &pcfg_pull_none>;
 			};
 
-			i2c2m05v_gpio: i2c2m05v-gpio {
+			i2c2m05v_pins: i2c2m05v-pins {
 				rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,
 						<1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
@@ -867,7 +868,7 @@ otp_out: otp-out {
 				rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>;
 			};
 
-			otp_gpio: otp-gpio {
+			otp_pin: otp-pin {
 				rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 		};
@@ -886,7 +887,7 @@ uart0_rts: uart0-rts {
 				rockchip,pins = <3 RK_PA3 1 &pcfg_pull_none>;
 			};
 
-			uart0_rts_gpio: uart0-rts-gpio {
+			uart0_rts_pin: uart0-rts-pin {
 				rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
 			};
 		};

arch/arm64/boot/dts/rockchip/rk3399pro-rock-pi-n10.dts

@@ -8,11 +8,15 @@
 /dts-v1/;
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
-#include "rk3399pro-vmarc-som.dtsi"
 #include <arm/rockchip-radxa-dalang-carrier.dtsi>
+#include "rk3399pro-vmarc-som.dtsi"
 
 / {
 	model = "Radxa ROCK Pi N10";
 	compatible = "radxa,rockpi-n10", "vamrs,rk3399pro-vmarc-som",
 		     "rockchip,rk3399pro";
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
 };

arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi

@@ -12,30 +12,16 @@
 / {
 	compatible = "vamrs,rk3399pro-vmarc-som", "rockchip,rk3399pro";
 
-	clkin_gmac: external-gmac-clock {
-		compatible = "fixed-clock";
-		clock-frequency = <125000000>;
-		clock-output-names = "clkin_gmac";
-		#clock-cells = <0>;
-	};
-
-	vcc12v_dcin: vcc12v-dcin-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc12v_dcin";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-	};
-
-	vcc5v0_sys: vcc5v0-sys-regulator {
+	vcc3v3_pcie: vcc-pcie-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0_sys";
+		enable-active-high;
+		gpio = <&gpio4 RK_PD4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_pwr>;
+		regulator-name = "vcc3v3_pcie";
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc12v_dcin>;
+		vin-supply = <&vcc5v0_sys>;
 	};
 };
 
@@ -61,23 +47,20 @@ &emmc_phy {
 
 &gmac {
 	assigned-clocks = <&cru SCLK_RMII_SRC>;
-	assigned-clock-parents = <&clkin_gmac>;
-	clock_in_out = "input";
 	phy-supply = <&vcc_lan>;
-	phy-mode = "rgmii";
-	pinctrl-names = "default";
-	pinctrl-0 = <&rgmii_pins>;
 	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 50000>;
-	tx_delay = <0x28>;
-	rx_delay = <0x11>;
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec>;
 };
 
 &i2c0 {
 	clock-frequency = <400000>;
-	i2c-scl-rising-time-ns = <180>;
 	i2c-scl-falling-time-ns = <30>;
+	i2c-scl-rising-time-ns = <180>;
 	status = "okay";
 
 	rk809: pmic@20 {
@@ -171,7 +154,8 @@ vcca_0v9: LDO_REG1 {
 				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <900000>;
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
 				};
 			};
 
@@ -206,7 +190,8 @@ vcca_1v8: LDO_REG4 {
 				regulator-min-microvolt = <1850000>;
 				regulator-max-microvolt = <1850000>;
 				regulator-state-mem {
-					regulator-off-in-suspend;
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1850000>;
 				};
 			};
 
@@ -297,11 +282,88 @@ regulator-state-mem {
 	};
 };
 
+&i2c1 {
+	i2c-scl-falling-time-ns = <30>;
+	i2c-scl-rising-time-ns = <140>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "hym8563";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <RK_PD6 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c3 {
+	i2c-scl-rising-time-ns = <450>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
 &io_domains {
 	status = "okay";
 	bt656-supply = <&vcca_1v8>;
-	sdmmc-supply = <&vccio_sd>;
 	gpio1830-supply = <&vccio_3v0>;
+	sdmmc-supply = <&vccio_sd>;
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pcie0 {
+	ep-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+	max-link-speed = <2>;
+	num-lanes = <4>;
+	pinctrl-0 = <&pcie_clkreqnb_cpm>;
+	pinctrl-names = "default";
+	vpcie0v9-supply = <&vcca_0v9>;	/* VCC_0V9_S0 */
+	vpcie1v8-supply = <&vcca_1v8>;	/* VCC_1V8_S0 */
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&pinctrl {
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <4 RK_PD6 0 &pcfg_pull_up>;
+		};
+	};
+
+	pcie {
+		pcie_pwr: pcie-pwr {
+			rockchip,pins =	<4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC2 0 &pcfg_pull_up>;
+		};
+	};
+
+	vbus_host {
+		usb1_en_oc: usb1-en-oc {
+			rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	vbus_typec {
+		usb0_en_oc: usb0-en-oc {
+			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
 };
 
 &pmu_io_domains {
@@ -317,17 +379,79 @@ &sdhci {
 	status = "okay";
 };
 
-&tsadc {
+&sdmmc {
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	max-frequency = <150000000>;
+};
+
+&tcphy0 {
 	status = "okay";
+};
+
+&tsadc {
 	rockchip,hw-tshut-mode = <1>;
 	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
 };
 
-&pinctrl {
-	pmic {
-		pmic_int_l: pmic-int-l {
-			rockchip,pins =
-				<1 RK_PC2 0 &pcfg_pull_up>;
-		};
+&u2phy0 {
+	status = "okay";
+
+	u2phy0_otg: otg-port {
+		phy-supply = <&vbus_typec>;
+		status = "okay";
+	};
+
+	u2phy0_host: host-port {
+		phy-supply = <&vbus_host>;
+		status = "okay";
+	};
+};
+
+
+&u2phy1 {
+	status = "okay";
+
+	u2phy1_host: host-port {
+		phy-supply = <&vbus_host>;
+		status = "okay";
 	};
 };
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usbdrd3_0 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	status = "okay";
+};
+
+&vbus_host {
+	enable-active-high;
+	gpio = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>; /* USB1_EN_OC# */
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_en_oc>;
+};
+
+&vbus_typec {
+	enable-active-high;
+	gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; /* USB0_EN_OC# */
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_en_oc>;
+};