wifi: ath11k: Fix kernel-doc issues

Fix documentation issues reported by kernel-doc:
- Incorrect use of /** for non-kernel-doc comments
- Mismatch between documented and actual identifiers
- Incorrect identifier syntax
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220909151246.22961-1-quic_jjohnson@quicinc.com

drivers/net/wireless/ath/ath11k/dp.h

@@ -997,8 +997,7 @@ struct htt_rx_ring_tlv_filter {
 #define HTT_RX_FULL_MON_MODE_CFG_CMD_CFG_NON_ZERO_MPDUS_END	BIT(2)
 #define HTT_RX_FULL_MON_MODE_CFG_CMD_CFG_RELEASE_RING		GENMASK(10, 3)
 
-/**
- * Enumeration for full monitor mode destination ring select
+/* Enumeration for full monitor mode destination ring select
  * 0 - REO destination ring select
  * 1 - FW destination ring select
  * 2 - SW destination ring select
@@ -1395,8 +1394,7 @@ struct htt_ppdu_stats_info {
 	struct list_head list;
 };
 
-/**
- * @brief target -> host packet log message
+/* @brief target -> host packet log message
  *
  * @details
  * The following field definitions describe the format of the packet log
@@ -1434,8 +1432,7 @@ struct htt_pktlog_msg {
 	u8 payload[];
 };
 
-/**
- * @brief host -> target FW extended statistics retrieve
+/* @brief host -> target FW extended statistics retrieve
  *
  * @details
  * The following field definitions describe the format of the HTT host
@@ -1570,8 +1567,7 @@ struct htt_ext_stats_cfg_params {
 	u32 cfg3;
 };
 
-/**
- * @brief target -> host extended statistics upload
+/* @brief target -> host extended statistics upload
  *
  * @details
  * The following field definitions describe the format of the HTT target

drivers/net/wireless/ath/ath11k/hal.h

@@ -451,13 +451,13 @@ enum hal_ring_type {
 
 /**
  * enum hal_reo_cmd_type: Enum for REO command type
- * @CMD_GET_QUEUE_STATS: Get REO queue status/stats
- * @CMD_FLUSH_QUEUE: Flush all frames in REO queue
- * @CMD_FLUSH_CACHE: Flush descriptor entries in the cache
- * @CMD_UNBLOCK_CACHE: Unblock a descriptor's address that was blocked
+ * @HAL_REO_CMD_GET_QUEUE_STATS: Get REO queue status/stats
+ * @HAL_REO_CMD_FLUSH_QUEUE: Flush all frames in REO queue
+ * @HAL_REO_CMD_FLUSH_CACHE: Flush descriptor entries in the cache
+ * @HAL_REO_CMD_UNBLOCK_CACHE: Unblock a descriptor's address that was blocked
  *      earlier with a 'REO_FLUSH_CACHE' command
- * @CMD_FLUSH_TIMEOUT_LIST: Flush buffers/descriptors from timeout list
- * @CMD_UPDATE_RX_REO_QUEUE: Update REO queue settings
+ * @HAL_REO_CMD_FLUSH_TIMEOUT_LIST: Flush buffers/descriptors from timeout list
+ * @HAL_REO_CMD_UPDATE_RX_QUEUE: Update REO queue settings
  */
 enum hal_reo_cmd_type {
 	HAL_REO_CMD_GET_QUEUE_STATS     = 0,
@@ -875,8 +875,7 @@ struct hal_reo_status {
 	} u;
 };
 
-/**
- * HAL context to be used to access SRNG APIs (currently used by data path
+/* HAL context to be used to access SRNG APIs (currently used by data path
  * and transport (CE) modules)
  */
 struct ath11k_hal {

drivers/net/wireless/ath/ath11k/wmi.h

@@ -4820,9 +4820,9 @@ enum wmi_rate_preamble {
 
 /**
  * enum wmi_rtscts_prot_mode - Enable/Disable RTS/CTS and CTS2Self Protection.
- * @WMI_RTS_CTS_DISABLED : RTS/CTS protection is disabled.
- * @WMI_USE_RTS_CTS : RTS/CTS Enabled.
- * @WMI_USE_CTS2SELF : CTS to self protection Enabled.
+ * @WMI_RTS_CTS_DISABLED: RTS/CTS protection is disabled.
+ * @WMI_USE_RTS_CTS: RTS/CTS Enabled.
+ * @WMI_USE_CTS2SELF: CTS to self protection Enabled.
  */
 enum wmi_rtscts_prot_mode {
 	WMI_RTS_CTS_DISABLED = 0,
@@ -4833,13 +4833,13 @@ enum wmi_rtscts_prot_mode {
 /**
  * enum wmi_rtscts_profile - Selection of RTS CTS profile along with enabling
  *                           protection mode.
- * @WMI_RTSCTS_FOR_NO_RATESERIES - Neither of rate-series should use RTS-CTS
- * @WMI_RTSCTS_FOR_SECOND_RATESERIES - Only second rate-series will use RTS-CTS
- * @WMI_RTSCTS_ACROSS_SW_RETRIES - Only the second rate-series will use RTS-CTS,
- *                                 but if there's a sw retry, both the rate
- *                                 series will use RTS-CTS.
- * @WMI_RTSCTS_ERP - RTS/CTS used for ERP protection for every PPDU.
- * @WMI_RTSCTS_FOR_ALL_RATESERIES - Enable RTS-CTS for all rate series.
+ * @WMI_RTSCTS_FOR_NO_RATESERIES: Neither of rate-series should use RTS-CTS
+ * @WMI_RTSCTS_FOR_SECOND_RATESERIES: Only second rate-series will use RTS-CTS
+ * @WMI_RTSCTS_ACROSS_SW_RETRIES: Only the second rate-series will use RTS-CTS,
+ *                                but if there's a sw retry, both the rate
+ *                                series will use RTS-CTS.
+ * @WMI_RTSCTS_ERP: RTS/CTS used for ERP protection for every PPDU.
+ * @WMI_RTSCTS_FOR_ALL_RATESERIES: Enable RTS-CTS for all rate series.
  */
 enum wmi_rtscts_profile {
 	WMI_RTSCTS_FOR_NO_RATESERIES = 0,