Merge branch 'imx/soc' into imx/dt

Documentation/devicetree/bindings/power/fsl,imx-gpc.txt

+Freescale i.MX General Power Controller
+=======================================
+
+The i.MX6Q General Power Control (GPC) block contains DVFS load tracking
+counters and Power Gating Control (PGC) for the CPU and PU (GPU/VPU) power
+domains.
+
+Required properties:
+- compatible: Should be "fsl,imx6q-gpc" or "fsl,imx6sl-gpc"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain GPC interrupt request 1
+- pu-supply: Link to the LDO regulator powering the PU power domain
+- clocks: Clock phandles to devices in the PU power domain that need
+	  to be enabled during domain power-up for reset propagation.
+- #power-domain-cells: Should be 1, see below:
+
+The gpc node is a power-controller as documented by the generic power domain
+bindings in Documentation/devicetree/bindings/power/power_domain.txt.
+
+Example:
+
+	gpc: gpc@020dc000 {
+		compatible = "fsl,imx6q-gpc";
+		reg = <0x020dc000 0x4000>;
+		interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 90 IRQ_TYPE_LEVEL_HIGH>;
+		pu-supply = <&reg_pu>;
+		clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>,
+			 <&clks IMX6QDL_CLK_GPU3D_SHADER>,
+			 <&clks IMX6QDL_CLK_GPU2D_CORE>,
+			 <&clks IMX6QDL_CLK_GPU2D_AXI>,
+			 <&clks IMX6QDL_CLK_OPENVG_AXI>,
+			 <&clks IMX6QDL_CLK_VPU_AXI>;
+		#power-domain-cells = <1>;
+	};
+
+
+Specifying power domain for IP modules
+======================================
+
+IP cores belonging to a power domain should contain a 'power-domains' property
+that is a phandle pointing to the gpc device node and a DOMAIN_INDEX specifying
+the power domain the device belongs to.
+
+Example of a device that is part of the PU power domain:
+
+	vpu: vpu@02040000 {
+		reg = <0x02040000 0x3c000>;
+		/* ... */
+		power-domains = <&gpc 1>;
+		/* ... */
+	};
+
+The following DOMAIN_INDEX values are valid for i.MX6Q:
+ARM_DOMAIN     0
+PU_DOMAIN      1
+The following additional DOMAIN_INDEX value is valid for i.MX6SL:
+DISPLAY_DOMAIN 2

arch/arm/mach-imx/Kconfig

@@ -21,6 +21,7 @@ config MXC_AVIC
 
 config MXC_DEBUG_BOARD
 	bool "Enable MXC debug board(for 3-stack)"
+	depends on MACH_MX27_3DS || MACH_MX31_3DS || MACH_MX35_3DS
 	help
 	  The debug board is an integral part of the MXC 3-stack(PDK)
 	  platforms, it can be attached or removed from the peripheral
@@ -50,6 +51,7 @@ config HAVE_IMX_ANATOP
 
 config HAVE_IMX_GPC
 	bool
+	select PM_GENERIC_DOMAINS if PM
 
 config HAVE_IMX_MMDC
 	bool
@@ -585,6 +587,7 @@ config SOC_VF610
 	select ARM_GIC
 	select PINCTRL_VF610
 	select PL310_ERRATA_769419 if CACHE_L2X0
+	select SMP_ON_UP if SMP
 
 	help
 	  This enables support for Freescale Vybrid VF610 processor.

arch/arm/mach-imx/clk-imx6q.c

@@ -119,6 +119,7 @@ static unsigned int share_count_asrc;
 static unsigned int share_count_ssi1;
 static unsigned int share_count_ssi2;
 static unsigned int share_count_ssi3;
+static unsigned int share_count_mipi_core_cfg;
 
 static void __init imx6q_clocks_init(struct device_node *ccm_node)
 {
@@ -246,6 +247,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	clk[IMX6QDL_CLK_PLL3_60M]  = imx_clk_fixed_factor("pll3_60m",  "pll3_usb_otg",   1, 8);
 	clk[IMX6QDL_CLK_TWD]       = imx_clk_fixed_factor("twd",       "arm",            1, 2);
 	clk[IMX6QDL_CLK_GPT_3M]    = imx_clk_fixed_factor("gpt_3m",    "osc",            1, 8);
+	clk[IMX6QDL_CLK_VIDEO_27M] = imx_clk_fixed_factor("video_27m", "pll3_pfd1_540m", 1, 20);
 	if (cpu_is_imx6dl()) {
 		clk[IMX6QDL_CLK_GPU2D_AXI] = imx_clk_fixed_factor("gpu2d_axi", "mmdc_ch0_axi_podf", 1, 1);
 		clk[IMX6QDL_CLK_GPU3D_AXI] = imx_clk_fixed_factor("gpu3d_axi", "mmdc_ch0_axi_podf", 1, 1);
@@ -400,7 +402,7 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 		clk[IMX6QDL_CLK_GPU2D_CORE] = imx_clk_gate2("gpu2d_core", "gpu2d_core_podf", base + 0x6c, 24);
 	clk[IMX6QDL_CLK_GPU3D_CORE]   = imx_clk_gate2("gpu3d_core",    "gpu3d_core_podf",   base + 0x6c, 26);
 	clk[IMX6QDL_CLK_HDMI_IAHB]    = imx_clk_gate2("hdmi_iahb",     "ahb",               base + 0x70, 0);
-	clk[IMX6QDL_CLK_HDMI_ISFR]    = imx_clk_gate2("hdmi_isfr",     "pll3_pfd1_540m",    base + 0x70, 4);
+	clk[IMX6QDL_CLK_HDMI_ISFR]    = imx_clk_gate2("hdmi_isfr",     "video_27m",         base + 0x70, 4);
 	clk[IMX6QDL_CLK_I2C1]         = imx_clk_gate2("i2c1",          "ipg_per",           base + 0x70, 6);
 	clk[IMX6QDL_CLK_I2C2]         = imx_clk_gate2("i2c2",          "ipg_per",           base + 0x70, 8);
 	clk[IMX6QDL_CLK_I2C3]         = imx_clk_gate2("i2c3",          "ipg_per",           base + 0x70, 10);
@@ -415,7 +417,9 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	clk[IMX6QDL_CLK_LDB_DI0]      = imx_clk_gate2("ldb_di0",       "ldb_di0_podf",      base + 0x74, 12);
 	clk[IMX6QDL_CLK_LDB_DI1]      = imx_clk_gate2("ldb_di1",       "ldb_di1_podf",      base + 0x74, 14);
 	clk[IMX6QDL_CLK_IPU2_DI1]     = imx_clk_gate2("ipu2_di1",      "ipu2_di1_sel",      base + 0x74, 10);
-	clk[IMX6QDL_CLK_HSI_TX]       = imx_clk_gate2("hsi_tx",        "hsi_tx_podf",       base + 0x74, 16);
+	clk[IMX6QDL_CLK_HSI_TX]       = imx_clk_gate2_shared("hsi_tx", "hsi_tx_podf",       base + 0x74, 16, &share_count_mipi_core_cfg);
+	clk[IMX6QDL_CLK_MIPI_CORE_CFG] = imx_clk_gate2_shared("mipi_core_cfg", "video_27m", base + 0x74, 16, &share_count_mipi_core_cfg);
+	clk[IMX6QDL_CLK_MIPI_IPG]     = imx_clk_gate2_shared("mipi_ipg", "ipg",             base + 0x74, 16, &share_count_mipi_core_cfg);
 	if (cpu_is_imx6dl())
 		/*
 		 * The multiplexer and divider of the imx6q clock gpu2d get

arch/arm/mach-imx/gpc.c

@@ -10,15 +10,25 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
+#include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/regulator/consumer.h>
 #include <linux/irqchip/arm-gic.h>
 #include "common.h"
+#include "hardware.h"
 
+#define GPC_CNTR		0x000
 #define GPC_IMR1		0x008
+#define GPC_PGC_GPU_PDN		0x260
+#define GPC_PGC_GPU_PUPSCR	0x264
+#define GPC_PGC_GPU_PDNSCR	0x268
 #define GPC_PGC_CPU_PDN		0x2a0
 #define GPC_PGC_CPU_PUPSCR	0x2a4
 #define GPC_PGC_CPU_PDNSCR	0x2a8
@@ -27,6 +37,18 @@
 
 #define IMR_NUM			4
 
+#define GPU_VPU_PUP_REQ		BIT(1)
+#define GPU_VPU_PDN_REQ		BIT(0)
+
+#define GPC_CLK_MAX		6
+
+struct pu_domain {
+	struct generic_pm_domain base;
+	struct regulator *reg;
+	struct clk *clk[GPC_CLK_MAX];
+	int num_clks;
+};
+
 static void __iomem *gpc_base;
 static u32 gpc_wake_irqs[IMR_NUM];
 static u32 gpc_saved_imrs[IMR_NUM];
@@ -170,3 +192,194 @@ void __init imx_gpc_init(void)
 	gic_arch_extn.irq_unmask = imx_gpc_irq_unmask;
 	gic_arch_extn.irq_set_wake = imx_gpc_irq_set_wake;
 }
+
+#ifdef CONFIG_PM_GENERIC_DOMAINS
+
+static void _imx6q_pm_pu_power_off(struct generic_pm_domain *genpd)
+{
+	int iso, iso2sw;
+	u32 val;
+
+	/* Read ISO and ISO2SW power down delays */
+	val = readl_relaxed(gpc_base + GPC_PGC_GPU_PDNSCR);
+	iso = val & 0x3f;
+	iso2sw = (val >> 8) & 0x3f;
+
+	/* Gate off PU domain when GPU/VPU when powered down */
+	writel_relaxed(0x1, gpc_base + GPC_PGC_GPU_PDN);
+
+	/* Request GPC to power down GPU/VPU */
+	val = readl_relaxed(gpc_base + GPC_CNTR);
+	val |= GPU_VPU_PDN_REQ;
+	writel_relaxed(val, gpc_base + GPC_CNTR);
+
+	/* Wait ISO + ISO2SW IPG clock cycles */
+	ndelay((iso + iso2sw) * 1000 / 66);
+}
+
+static int imx6q_pm_pu_power_off(struct generic_pm_domain *genpd)
+{
+	struct pu_domain *pu = container_of(genpd, struct pu_domain, base);
+
+	_imx6q_pm_pu_power_off(genpd);
+
+	if (pu->reg)
+		regulator_disable(pu->reg);
+
+	return 0;
+}
+
+static int imx6q_pm_pu_power_on(struct generic_pm_domain *genpd)
+{
+	struct pu_domain *pu = container_of(genpd, struct pu_domain, base);
+	int i, ret, sw, sw2iso;
+	u32 val;
+
+	if (pu->reg)
+		ret = regulator_enable(pu->reg);
+	if (pu->reg && ret) {
+		pr_err("%s: failed to enable regulator: %d\n", __func__, ret);
+		return ret;
+	}
+
+	/* Enable reset clocks for all devices in the PU domain */
+	for (i = 0; i < pu->num_clks; i++)
+		clk_prepare_enable(pu->clk[i]);
+
+	/* Gate off PU domain when GPU/VPU when powered down */
+	writel_relaxed(0x1, gpc_base + GPC_PGC_GPU_PDN);
+
+	/* Read ISO and ISO2SW power down delays */
+	val = readl_relaxed(gpc_base + GPC_PGC_GPU_PUPSCR);
+	sw = val & 0x3f;
+	sw2iso = (val >> 8) & 0x3f;
+
+	/* Request GPC to power up GPU/VPU */
+	val = readl_relaxed(gpc_base + GPC_CNTR);
+	val |= GPU_VPU_PUP_REQ;
+	writel_relaxed(val, gpc_base + GPC_CNTR);
+
+	/* Wait ISO + ISO2SW IPG clock cycles */
+	ndelay((sw + sw2iso) * 1000 / 66);
+
+	/* Disable reset clocks for all devices in the PU domain */
+	for (i = 0; i < pu->num_clks; i++)
+		clk_disable_unprepare(pu->clk[i]);
+
+	return 0;
+}
+
+static struct generic_pm_domain imx6q_arm_domain = {
+	.name = "ARM",
+};
+
+static struct pu_domain imx6q_pu_domain = {
+	.base = {
+		.name = "PU",
+		.power_off = imx6q_pm_pu_power_off,
+		.power_on = imx6q_pm_pu_power_on,
+		.power_off_latency_ns = 25000,
+		.power_on_latency_ns = 2000000,
+	},
+};
+
+static struct generic_pm_domain imx6sl_display_domain = {
+	.name = "DISPLAY",
+};
+
+static struct generic_pm_domain *imx_gpc_domains[] = {
+	&imx6q_arm_domain,
+	&imx6q_pu_domain.base,
+	&imx6sl_display_domain,
+};
+
+static struct genpd_onecell_data imx_gpc_onecell_data = {
+	.domains = imx_gpc_domains,
+	.num_domains = ARRAY_SIZE(imx_gpc_domains),
+};
+
+static int imx_gpc_genpd_init(struct device *dev, struct regulator *pu_reg)
+{
+	struct clk *clk;
+	bool is_off;
+	int i;
+
+	imx6q_pu_domain.reg = pu_reg;
+
+	for (i = 0; ; i++) {
+		clk = of_clk_get(dev->of_node, i);
+		if (IS_ERR(clk))
+			break;
+		if (i >= GPC_CLK_MAX) {
+			dev_err(dev, "more than %d clocks\n", GPC_CLK_MAX);
+			goto clk_err;
+		}
+		imx6q_pu_domain.clk[i] = clk;
+	}
+	imx6q_pu_domain.num_clks = i;
+
+	is_off = IS_ENABLED(CONFIG_PM);
+	if (is_off) {
+		_imx6q_pm_pu_power_off(&imx6q_pu_domain.base);
+	} else {
+		/*
+		 * Enable power if compiled without CONFIG_PM in case the
+		 * bootloader disabled it.
+		 */
+		imx6q_pm_pu_power_on(&imx6q_pu_domain.base);
+	}
+
+	pm_genpd_init(&imx6q_pu_domain.base, NULL, is_off);
+	return of_genpd_add_provider_onecell(dev->of_node,
+					     &imx_gpc_onecell_data);
+
+clk_err:
+	while (i--)
+		clk_put(imx6q_pu_domain.clk[i]);
+	return -EINVAL;
+}
+
+#else
+static inline int imx_gpc_genpd_init(struct device *dev, struct regulator *reg)
+{
+	return 0;
+}
+#endif /* CONFIG_PM_GENERIC_DOMAINS */
+
+static int imx_gpc_probe(struct platform_device *pdev)
+{
+	struct regulator *pu_reg;
+	int ret;
+
+	pu_reg = devm_regulator_get_optional(&pdev->dev, "pu");
+	if (PTR_ERR(pu_reg) == -ENODEV)
+		pu_reg = NULL;
+	if (IS_ERR(pu_reg)) {
+		ret = PTR_ERR(pu_reg);
+		dev_err(&pdev->dev, "failed to get pu regulator: %d\n", ret);
+		return ret;
+	}
+
+	return imx_gpc_genpd_init(&pdev->dev, pu_reg);
+}
+
+static const struct of_device_id imx_gpc_dt_ids[] = {
+	{ .compatible = "fsl,imx6q-gpc" },
+	{ .compatible = "fsl,imx6sl-gpc" },
+	{ }
+};
+
+static struct platform_driver imx_gpc_driver = {
+	.driver = {
+		.name = "imx-gpc",
+		.owner = THIS_MODULE,
+		.of_match_table = imx_gpc_dt_ids,
+	},
+	.probe = imx_gpc_probe,
+};
+
+static int __init imx_pgc_init(void)
+{
+	return platform_driver_register(&imx_gpc_driver);
+}
+subsys_initcall(imx_pgc_init);

drivers/bus/imx-weim.c

@@ -142,7 +142,7 @@ static int __init weim_parse_dt(struct platform_device *pdev,
 							   &pdev->dev);
 	const struct imx_weim_devtype *devtype = of_id->data;
 	struct device_node *child;
-	int ret;
+	int ret, have_child = 0;
 
 	if (devtype == &imx50_weim_devtype) {
 		ret = imx_weim_gpr_setup(pdev);
@@ -155,14 +155,15 @@ static int __init weim_parse_dt(struct platform_device *pdev,
 			continue;
 
 		ret = weim_timing_setup(child, base, devtype);
-		if (ret) {
-			dev_err(&pdev->dev, "%s set timing failed.\n",
+		if (ret)
+			dev_warn(&pdev->dev, "%s set timing failed.\n",
 				child->full_name);
-			return ret;
-		}
+		else
+			have_child = 1;
 	}
 
-	ret = of_platform_populate(pdev->dev.of_node,
+	if (have_child)
+		ret = of_platform_populate(pdev->dev.of_node,
 				   of_default_bus_match_table,
 				   NULL, &pdev->dev);
 	if (ret)

include/dt-bindings/clock/imx6qdl-clock.h

@@ -248,6 +248,9 @@
 #define IMX6QDL_PLL6_BYPASS			235
 #define IMX6QDL_PLL7_BYPASS			236
 #define IMX6QDL_CLK_GPT_3M			237
-#define IMX6QDL_CLK_END				238
+#define IMX6QDL_CLK_VIDEO_27M			238
+#define IMX6QDL_CLK_MIPI_CORE_CFG		239
+#define IMX6QDL_CLK_MIPI_IPG			240
+#define IMX6QDL_CLK_END				241
 
 #endif /* __DT_BINDINGS_CLOCK_IMX6QDL_H */

include/linux/mfd/syscon/imx6q-iomuxc-gpr.h

@@ -207,6 +207,7 @@
 #define IMX6Q_GPR3_LVDS0_MUX_CTL_IPU1_DI1	(0x1 << 6)
 #define IMX6Q_GPR3_LVDS0_MUX_CTL_IPU2_DI0	(0x2 << 6)
 #define IMX6Q_GPR3_LVDS0_MUX_CTL_IPU2_DI1	(0x3 << 6)
+#define IMX6Q_GPR3_MIPI_MUX_CTL_SHIFT		4
 #define IMX6Q_GPR3_MIPI_MUX_CTL_MASK		(0x3 << 4)
 #define IMX6Q_GPR3_MIPI_MUX_CTL_IPU1_DI0	(0x0 << 4)
 #define IMX6Q_GPR3_MIPI_MUX_CTL_IPU1_DI1	(0x1 << 4)