Merge branch 'for-v4.7/gpmc-mtd-common' of github.com:rogerq/linux into nand/next

Pull NAND/GPMC updates from Roger Quadros:
 "We do a couple of things in this series which result in cleaner device
  tree implementation, faster perfomance and multi-platform support. As
  an added bonus we get to use the GPMC_WAIT pins as GPI/Interrupts.

  - Establish a custom interface between NAND and GPMC driver. This is
    needed because all of the NAND registers sit in the GPMC register
    space.

  - Clean up device tree support so that omap-gpmc IP and the omap2 NAND
    driver can be used on non-OMAP platforms. e.g. Keystone.

  - Implement GPIOCHIP for the GPMC WAITPINS. SoCs can contain 2 to 4 of
    these and most of them would be unused otherwise. It also allows a
    cleaner implementation of NAND Ready pin status for the NAND driver.

  - Implement GPMC IRQ domain to proivde the 2 NAND events and GPMC
    WAITPIN edge interrupts.

  - Implement GPIOlib based NAND ready pin checking for OMAP NAND driver.
    On dra7-evm, Read speed increases from 13768 KiB/ to 17246 KiB/s.
    Write speed was unchanged at 7123 KiB/s."

* 'for-v4.7/gpmc-mtd-common' of github.com:rogerq/linux:
  mtd: nand: omap2: Implement NAND ready using gpiolib
  memory: omap-gpmc: Prevent GPMC_STATUS from being accessed via gpmc_regs
  memory: omap-gpmc: Support WAIT pin edge interrupts
  memory: omap-gpmc: Reserve WAITPIN if needed for WAIT monitoring
  memory: omap-gpmc: Support general purpose input for WAITPINs
  memory: omap-gpmc: Move device tree binding to correct location
  memory: omap-gpmc: Prevent mapping into 1st 16MB
  mtd: nand: omap: Update DT binding documentation
  mtd: nand: omap: Clean up device tree support
  mtd: nand: omap: Copy platform data parameters to omap_nand_info data
  mtd: nand: omap: Switch to using GPMC-NAND ops for writebuffer empty check
  mtd: nand: omap: Use gpmc_omap_get_nand_ops() to get NAND registers
  memory: omap-gpmc: Implement IRQ domain for NAND IRQs
  memory: omap-gpmc: Add GPMC-NAND ops to get writebufferempty status
  memory: omap-gpmc: Introduce GPMC to NAND interface
  ARM: OMAP2+: gpmc: Add gpmc timings and settings to platform data
  ARM: OMAP2+: gpmc: Add platform data

Documentation/devicetree/bindings/bus/ti-gpmc.txt → Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt

@@ -32,6 +32,19 @@ Required properties:
 			bootloader) are used for the physical address decoding.
 			As this will change in the future, filling correct
 			values here is a requirement.
+ - interrupt-controller: The GPMC driver implements and interrupt controller for
+			the NAND events "fifoevent" and "termcount" plus the
+			rising/falling edges on the GPMC_WAIT pins.
+			The interrupt number mapping is as follows
+			0 - NAND_fifoevent
+			1 - NAND_termcount
+			2 - GPMC_WAIT0 pin edge
+			3 - GPMC_WAIT1 pin edge, and so on.
+ - interrupt-cells:	Must be set to 2
+ - gpio-controller:	The GPMC driver implements a GPIO controller for the
+			GPMC WAIT pins that can be used as general purpose inputs.
+			0 maps to GPMC_WAIT0 pin.
+ - gpio-cells:		Must be set to 2
 
 Timing properties for child nodes. All are optional and default to 0.
 
@@ -130,6 +143,10 @@ Example for an AM33xx board:
 		#address-cells = <2>;
 		#size-cells = <1>;
 		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
 
 		/* child nodes go here */
 	};

Documentation/devicetree/bindings/mtd/gpmc-nand.txt

@@ -13,7 +13,11 @@ Documentation/devicetree/bindings/mtd/nand.txt
 
 Required properties:
 
- - reg:		The CS line the peripheral is connected to
+ - compatible:	"ti,omap2-nand"
+ - reg:		range id (CS number), base offset and length of the
+		NAND I/O space
+ - interrupt-parent: must point to gpmc node
+ - interrupts:	Two interrupt specifiers, one for fifoevent, one for termcount.
 
 Optional properties:
 
@@ -44,6 +48,7 @@ Optional properties:
 		locating ECC errors for BCHx algorithms. SoC devices which have
 		ELM hardware engines should specify this device node in .dtsi
 		Using ELM for ECC error correction frees some CPU cycles.
+ - rb-gpios:	GPIO specifier for the ready/busy# pin.
 
 For inline partition table parsing (optional):
 
@@ -55,20 +60,26 @@ Example for an AM33xx board:
 	gpmc: gpmc@50000000 {
 		compatible = "ti,am3352-gpmc";
 		ti,hwmods = "gpmc";
-		reg = <0x50000000 0x1000000>;
+		reg = <0x50000000 0x36c>;
 		interrupts = <100>;
 		gpmc,num-cs = <8>;
 		gpmc,num-waitpins = <2>;
 		#address-cells = <2>;
 		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x2000>;	/* CS0: NAND */
+		ranges = <0 0 0x08000000 0x1000000>;	/* CS0 space, 16MB */
 		elm_id = <&elm>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
 
 		nand@0,0 {
-			reg = <0 0 0>; /* CS0, offset 0 */
+			compatible = "ti,omap2-nand";
+			reg = <0 0 4>;		/* CS0, offset 0, NAND I/O window 4 */
+			interrupt-parent = <&gpmc>;
+			interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE NONE>;
 			nand-bus-width = <16>;
 			ti,nand-ecc-opt = "bch8";
 			ti,nand-xfer-type = "polled";
+			rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 
 			gpmc,sync-clk-ps = <0>;
 			gpmc,cs-on-ns = <0>;

arch/arm/mach-omap2/gpmc-nand.c

@@ -97,10 +97,7 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 	gpmc_nand_res[2].start = gpmc_get_client_irq(GPMC_IRQ_COUNT_EVENT);
 
 	memset(&s, 0, sizeof(struct gpmc_settings));
-	if (gpmc_nand_data->of_node)
-		gpmc_read_settings_dt(gpmc_nand_data->of_node, &s);
-	else
-		gpmc_set_legacy(gpmc_nand_data, &s);
+	gpmc_set_legacy(gpmc_nand_data, &s);
 
 	s.device_nand = true;
 
@@ -121,8 +118,6 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 	if (err < 0)
 		goto out_free_cs;
 
-	gpmc_update_nand_reg(&gpmc_nand_data->reg, gpmc_nand_data->cs);
-
 	if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt)) {
 		pr_err("omap2-nand: Unsupported NAND ECC scheme selected\n");
 		err = -EINVAL;

drivers/memory/Kconfig

@@ -51,6 +51,7 @@ config TI_EMIF
 
 config OMAP_GPMC
 	bool
+	select GPIOLIB
 	help
 	  This driver is for the General Purpose Memory Controller (GPMC)
 	  present on Texas Instruments SoCs (e.g. OMAP2+). GPMC allows

include/linux/omap-gpmc.h

@@ -7,161 +7,53 @@
  *  option) any later version.
  */
 
-/* Maximum Number of Chip Selects */
-#define GPMC_CS_NUM		8
+#include <linux/platform_data/gpmc-omap.h>
 
 #define GPMC_CONFIG_WP		0x00000005
 
-#define GPMC_IRQ_FIFOEVENTENABLE	0x01
-#define GPMC_IRQ_COUNT_EVENT		0x02
-
-#define GPMC_BURST_4			4	/* 4 word burst */
-#define GPMC_BURST_8			8	/* 8 word burst */
-#define GPMC_BURST_16			16	/* 16 word burst */
-#define GPMC_DEVWIDTH_8BIT		1	/* 8-bit device width */
-#define GPMC_DEVWIDTH_16BIT		2	/* 16-bit device width */
-#define GPMC_MUX_AAD			1	/* Addr-Addr-Data multiplex */
-#define GPMC_MUX_AD			2	/* Addr-Data multiplex */
-
-/* bool type time settings */
-struct gpmc_bool_timings {
-	bool cycle2cyclediffcsen;
-	bool cycle2cyclesamecsen;
-	bool we_extra_delay;
-	bool oe_extra_delay;
-	bool adv_extra_delay;
-	bool cs_extra_delay;
-	bool time_para_granularity;
-};
+/* IRQ numbers in GPMC IRQ domain for legacy boot use */
+#define GPMC_IRQ_FIFOEVENTENABLE	0
+#define GPMC_IRQ_COUNT_EVENT		1
 
-/*
- * Note that all values in this struct are in nanoseconds except sync_clk
- * (which is in picoseconds), while the register values are in gpmc_fck cycles.
+/**
+ * gpmc_nand_ops - Interface between NAND and GPMC
+ * @nand_write_buffer_empty: get the NAND write buffer empty status.
  */
-struct gpmc_timings {
-	/* Minimum clock period for synchronous mode (in picoseconds) */
-	u32 sync_clk;
-
-	/* Chip-select signal timings corresponding to GPMC_CS_CONFIG2 */
-	u32 cs_on;		/* Assertion time */
-	u32 cs_rd_off;		/* Read deassertion time */
-	u32 cs_wr_off;		/* Write deassertion time */
-
-	/* ADV signal timings corresponding to GPMC_CONFIG3 */
-	u32 adv_on;		/* Assertion time */
-	u32 adv_rd_off;		/* Read deassertion time */
-	u32 adv_wr_off;		/* Write deassertion time */
-	u32 adv_aad_mux_on;	/* ADV assertion time for AAD */
-	u32 adv_aad_mux_rd_off;	/* ADV read deassertion time for AAD */
-	u32 adv_aad_mux_wr_off;	/* ADV write deassertion time for AAD */
-
-	/* WE signals timings corresponding to GPMC_CONFIG4 */
-	u32 we_on;		/* WE assertion time */
-	u32 we_off;		/* WE deassertion time */
-
-	/* OE signals timings corresponding to GPMC_CONFIG4 */
-	u32 oe_on;		/* OE assertion time */
-	u32 oe_off;		/* OE deassertion time */
-	u32 oe_aad_mux_on;	/* OE assertion time for AAD */
-	u32 oe_aad_mux_off;	/* OE deassertion time for AAD */
-
-	/* Access time and cycle time timings corresponding to GPMC_CONFIG5 */
-	u32 page_burst_access;	/* Multiple access word delay */
-	u32 access;		/* Start-cycle to first data valid delay */
-	u32 rd_cycle;		/* Total read cycle time */
-	u32 wr_cycle;		/* Total write cycle time */
-
-	u32 bus_turnaround;
-	u32 cycle2cycle_delay;
-
-	u32 wait_monitoring;
-	u32 clk_activation;
-
-	/* The following are only on OMAP3430 */
-	u32 wr_access;		/* WRACCESSTIME */
-	u32 wr_data_mux_bus;	/* WRDATAONADMUXBUS */
-
-	struct gpmc_bool_timings bool_timings;
+struct gpmc_nand_ops {
+	bool (*nand_writebuffer_empty)(void);
 };
 
-/* Device timings in picoseconds */
-struct gpmc_device_timings {
-	u32 t_ceasu;	/* address setup to CS valid */
-	u32 t_avdasu;	/* address setup to ADV valid */
-	/* XXX: try to combine t_avdp_r & t_avdp_w. Issue is
-	 * of tusb using these timings even for sync whilst
-	 * ideally for adv_rd/(wr)_off it should have considered
-	 * t_avdh instead. This indirectly necessitates r/w
-	 * variations of t_avdp as it is possible to have one
-	 * sync & other async
-	 */
-	u32 t_avdp_r;	/* ADV low time (what about t_cer ?) */
-	u32 t_avdp_w;
-	u32 t_aavdh;	/* address hold time */
-	u32 t_oeasu;	/* address setup to OE valid */
-	u32 t_aa;	/* access time from ADV assertion */
-	u32 t_iaa;	/* initial access time */
-	u32 t_oe;	/* access time from OE assertion */
-	u32 t_ce;	/* access time from CS asertion */
-	u32 t_rd_cycle;	/* read cycle time */
-	u32 t_cez_r;	/* read CS deassertion to high Z */
-	u32 t_cez_w;	/* write CS deassertion to high Z */
-	u32 t_oez;	/* OE deassertion to high Z */
-	u32 t_weasu;	/* address setup to WE valid */
-	u32 t_wpl;	/* write assertion time */
-	u32 t_wph;	/* write deassertion time */
-	u32 t_wr_cycle;	/* write cycle time */
-
-	u32 clk;
-	u32 t_bacc;	/* burst access valid clock to output delay */
-	u32 t_ces;	/* CS setup time to clk */
-	u32 t_avds;	/* ADV setup time to clk */
-	u32 t_avdh;	/* ADV hold time from clk */
-	u32 t_ach;	/* address hold time from clk */
-	u32 t_rdyo;	/* clk to ready valid */
-
-	u32 t_ce_rdyz;	/* XXX: description ?, or use t_cez instead */
-	u32 t_ce_avd;	/* CS on to ADV on delay */
-
-	/* XXX: check the possibility of combining
-	 * cyc_aavhd_oe & cyc_aavdh_we
-	 */
-	u8 cyc_aavdh_oe;/* read address hold time in cycles */
-	u8 cyc_aavdh_we;/* write address hold time in cycles */
-	u8 cyc_oe;	/* access time from OE assertion in cycles */
-	u8 cyc_wpl;	/* write deassertion time in cycles */
-	u32 cyc_iaa;	/* initial access time in cycles */
-
-	/* extra delays */
-	bool ce_xdelay;
-	bool avd_xdelay;
-	bool oe_xdelay;
-	bool we_xdelay;
-};
+struct gpmc_nand_regs;
 
-struct gpmc_settings {
-	bool burst_wrap;	/* enables wrap bursting */
-	bool burst_read;	/* enables read page/burst mode */
-	bool burst_write;	/* enables write page/burst mode */
-	bool device_nand;	/* device is NAND */
-	bool sync_read;		/* enables synchronous reads */
-	bool sync_write;	/* enables synchronous writes */
-	bool wait_on_read;	/* monitor wait on reads */
-	bool wait_on_write;	/* monitor wait on writes */
-	u32 burst_len;		/* page/burst length */
-	u32 device_width;	/* device bus width (8 or 16 bit) */
-	u32 mux_add_data;	/* multiplex address & data */
-	u32 wait_pin;		/* wait-pin to be used */
-};
+#if IS_ENABLED(CONFIG_OMAP_GPMC)
+struct gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *regs,
+					     int cs);
+#else
+static inline gpmc_nand_ops *gpmc_omap_get_nand_ops(struct gpmc_nand_regs *regs,
+						    int cs)
+{
+	return NULL;
+}
+#endif /* CONFIG_OMAP_GPMC */
+
+/*--------------------------------*/
+
+/* deprecated APIs */
+#if IS_ENABLED(CONFIG_OMAP_GPMC)
+void gpmc_update_nand_reg(struct gpmc_nand_regs *reg, int cs);
+#else
+static inline void gpmc_update_nand_reg(struct gpmc_nand_regs *reg, int cs)
+{
+}
+#endif /* CONFIG_OMAP_GPMC */
+/*--------------------------------*/
 
 extern int gpmc_calc_timings(struct gpmc_timings *gpmc_t,
 			     struct gpmc_settings *gpmc_s,
 			     struct gpmc_device_timings *dev_t);
 
-struct gpmc_nand_regs;
 struct device_node;
 
-extern void gpmc_update_nand_reg(struct gpmc_nand_regs *reg, int cs);
 extern int gpmc_get_client_irq(unsigned irq_config);
 
 extern unsigned int gpmc_ticks_to_ns(unsigned int ticks);

include/linux/platform_data/gpmc-omap.h

+/*
+ * OMAP GPMC Platform data
+ *
+ * Copyright (C) 2014 Texas Instruments, Inc. - http://www.ti.com
+ *	Roger Quadros <rogerq@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ */
+
+#ifndef _GPMC_OMAP_H_
+#define _GPMC_OMAP_H_
+
+/* Maximum Number of Chip Selects */
+#define GPMC_CS_NUM		8
+
+/* bool type time settings */
+struct gpmc_bool_timings {
+	bool cycle2cyclediffcsen;
+	bool cycle2cyclesamecsen;
+	bool we_extra_delay;
+	bool oe_extra_delay;
+	bool adv_extra_delay;
+	bool cs_extra_delay;
+	bool time_para_granularity;
+};
+
+/*
+ * Note that all values in this struct are in nanoseconds except sync_clk
+ * (which is in picoseconds), while the register values are in gpmc_fck cycles.
+ */
+struct gpmc_timings {
+	/* Minimum clock period for synchronous mode (in picoseconds) */
+	u32 sync_clk;
+
+	/* Chip-select signal timings corresponding to GPMC_CS_CONFIG2 */
+	u32 cs_on;		/* Assertion time */
+	u32 cs_rd_off;		/* Read deassertion time */
+	u32 cs_wr_off;		/* Write deassertion time */
+
+	/* ADV signal timings corresponding to GPMC_CONFIG3 */
+	u32 adv_on;		/* Assertion time */
+	u32 adv_rd_off;		/* Read deassertion time */
+	u32 adv_wr_off;		/* Write deassertion time */
+	u32 adv_aad_mux_on;	/* ADV assertion time for AAD */
+	u32 adv_aad_mux_rd_off;	/* ADV read deassertion time for AAD */
+	u32 adv_aad_mux_wr_off;	/* ADV write deassertion time for AAD */
+
+	/* WE signals timings corresponding to GPMC_CONFIG4 */
+	u32 we_on;		/* WE assertion time */
+	u32 we_off;		/* WE deassertion time */
+
+	/* OE signals timings corresponding to GPMC_CONFIG4 */
+	u32 oe_on;		/* OE assertion time */
+	u32 oe_off;		/* OE deassertion time */
+	u32 oe_aad_mux_on;	/* OE assertion time for AAD */
+	u32 oe_aad_mux_off;	/* OE deassertion time for AAD */
+
+	/* Access time and cycle time timings corresponding to GPMC_CONFIG5 */
+	u32 page_burst_access;	/* Multiple access word delay */
+	u32 access;		/* Start-cycle to first data valid delay */
+	u32 rd_cycle;		/* Total read cycle time */
+	u32 wr_cycle;		/* Total write cycle time */
+
+	u32 bus_turnaround;
+	u32 cycle2cycle_delay;
+
+	u32 wait_monitoring;
+	u32 clk_activation;
+
+	/* The following are only on OMAP3430 */
+	u32 wr_access;		/* WRACCESSTIME */
+	u32 wr_data_mux_bus;	/* WRDATAONADMUXBUS */
+
+	struct gpmc_bool_timings bool_timings;
+};
+
+/* Device timings in picoseconds */
+struct gpmc_device_timings {
+	u32 t_ceasu;	/* address setup to CS valid */
+	u32 t_avdasu;	/* address setup to ADV valid */
+	/* XXX: try to combine t_avdp_r & t_avdp_w. Issue is
+	 * of tusb using these timings even for sync whilst
+	 * ideally for adv_rd/(wr)_off it should have considered
+	 * t_avdh instead. This indirectly necessitates r/w
+	 * variations of t_avdp as it is possible to have one
+	 * sync & other async
+	 */
+	u32 t_avdp_r;	/* ADV low time (what about t_cer ?) */
+	u32 t_avdp_w;
+	u32 t_aavdh;	/* address hold time */
+	u32 t_oeasu;	/* address setup to OE valid */
+	u32 t_aa;	/* access time from ADV assertion */
+	u32 t_iaa;	/* initial access time */
+	u32 t_oe;	/* access time from OE assertion */
+	u32 t_ce;	/* access time from CS asertion */
+	u32 t_rd_cycle;	/* read cycle time */
+	u32 t_cez_r;	/* read CS deassertion to high Z */
+	u32 t_cez_w;	/* write CS deassertion to high Z */
+	u32 t_oez;	/* OE deassertion to high Z */
+	u32 t_weasu;	/* address setup to WE valid */
+	u32 t_wpl;	/* write assertion time */
+	u32 t_wph;	/* write deassertion time */
+	u32 t_wr_cycle;	/* write cycle time */
+
+	u32 clk;
+	u32 t_bacc;	/* burst access valid clock to output delay */
+	u32 t_ces;	/* CS setup time to clk */
+	u32 t_avds;	/* ADV setup time to clk */
+	u32 t_avdh;	/* ADV hold time from clk */
+	u32 t_ach;	/* address hold time from clk */
+	u32 t_rdyo;	/* clk to ready valid */
+
+	u32 t_ce_rdyz;	/* XXX: description ?, or use t_cez instead */
+	u32 t_ce_avd;	/* CS on to ADV on delay */
+
+	/* XXX: check the possibility of combining
+	 * cyc_aavhd_oe & cyc_aavdh_we
+	 */
+	u8 cyc_aavdh_oe;/* read address hold time in cycles */
+	u8 cyc_aavdh_we;/* write address hold time in cycles */
+	u8 cyc_oe;	/* access time from OE assertion in cycles */
+	u8 cyc_wpl;	/* write deassertion time in cycles */
+	u32 cyc_iaa;	/* initial access time in cycles */
+
+	/* extra delays */
+	bool ce_xdelay;
+	bool avd_xdelay;
+	bool oe_xdelay;
+	bool we_xdelay;
+};
+
+#define GPMC_BURST_4			4	/* 4 word burst */
+#define GPMC_BURST_8			8	/* 8 word burst */
+#define GPMC_BURST_16			16	/* 16 word burst */
+#define GPMC_DEVWIDTH_8BIT		1	/* 8-bit device width */
+#define GPMC_DEVWIDTH_16BIT		2	/* 16-bit device width */
+#define GPMC_MUX_AAD			1	/* Addr-Addr-Data multiplex */
+#define GPMC_MUX_AD			2	/* Addr-Data multiplex */
+
+struct gpmc_settings {
+	bool burst_wrap;	/* enables wrap bursting */
+	bool burst_read;	/* enables read page/burst mode */
+	bool burst_write;	/* enables write page/burst mode */
+	bool device_nand;	/* device is NAND */
+	bool sync_read;		/* enables synchronous reads */
+	bool sync_write;	/* enables synchronous writes */
+	bool wait_on_read;	/* monitor wait on reads */
+	bool wait_on_write;	/* monitor wait on writes */
+	u32 burst_len;		/* page/burst length */
+	u32 device_width;	/* device bus width (8 or 16 bit) */
+	u32 mux_add_data;	/* multiplex address & data */
+	u32 wait_pin;		/* wait-pin to be used */
+};
+
+/* Data for each chip select */
+struct gpmc_omap_cs_data {
+	bool valid;			/* data is valid */
+	bool is_nand;			/* device within this CS is NAND */
+	struct gpmc_settings *settings;
+	struct gpmc_device_timings *device_timings;
+	struct gpmc_timings *gpmc_timings;
+	struct platform_device *pdev;	/* device within this CS region */
+	unsigned int pdata_size;
+};
+
+struct gpmc_omap_platform_data {
+	struct gpmc_omap_cs_data cs[GPMC_CS_NUM];
+};
+
+#endif /* _GPMC_OMAP_H */

include/linux/platform_data/mtd-nand-omap2.h

@@ -45,7 +45,6 @@ enum omap_ecc {
 };
 
 struct gpmc_nand_regs {
-	void __iomem	*gpmc_status;
 	void __iomem	*gpmc_nand_command;
 	void __iomem	*gpmc_nand_address;
 	void __iomem	*gpmc_nand_data;
@@ -64,21 +63,24 @@ struct gpmc_nand_regs {
 	void __iomem	*gpmc_bch_result4[GPMC_BCH_NUM_REMAINDER];
 	void __iomem	*gpmc_bch_result5[GPMC_BCH_NUM_REMAINDER];
 	void __iomem	*gpmc_bch_result6[GPMC_BCH_NUM_REMAINDER];
+	/* Deprecated. Do not use */
+	void __iomem	*gpmc_status;
 };
 
 struct omap_nand_platform_data {
 	int			cs;
 	struct mtd_partition	*parts;
 	int			nr_parts;
-	bool			dev_ready;
 	bool			flash_bbt;
 	enum nand_io		xfer_type;
 	int			devsize;
 	enum omap_ecc           ecc_opt;
-	struct gpmc_nand_regs	reg;
 
-	/* for passing the partitions */
-	struct device_node	*of_node;
 	struct device_node	*elm_of_node;
+
+	/* deprecated */
+	struct gpmc_nand_regs	reg;
+	struct device_node	*of_node;
+	bool			dev_ready;
 };
 #endif