Commit 43db289d authored by Patrice Chotard's avatar Patrice Chotard Committed by Lee Jones

gpio: stmpe: Rework registers access

This update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset

This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.

For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: default avatarPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarLee Jones <lee.jones@linaro.org>
parent 897ac667
......@@ -20,6 +20,8 @@
*/
enum { REG_RE, REG_FE, REG_IE };
enum { LSB, CSB, MSB };
#define CACHE_NR_REGS 3
/* No variant has more than 24 GPIOs */
#define CACHE_NR_BANKS (24 / 8)
......@@ -39,7 +41,7 @@ static int stmpe_gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
u8 reg = stmpe->regs[STMPE_IDX_GPMR_LSB] - (offset / 8);
u8 reg = stmpe->regs[STMPE_IDX_GPMR_LSB + (offset / 8)];
u8 mask = 1 << (offset % 8);
int ret;
......@@ -55,7 +57,7 @@ static void stmpe_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
int which = val ? STMPE_IDX_GPSR_LSB : STMPE_IDX_GPCR_LSB;
u8 reg = stmpe->regs[which] - (offset / 8);
u8 reg = stmpe->regs[which + (offset / 8)];
u8 mask = 1 << (offset % 8);
/*
......@@ -89,7 +91,7 @@ static int stmpe_gpio_direction_output(struct gpio_chip *chip,
{
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB] - (offset / 8);
u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB + (offset / 8)];
u8 mask = 1 << (offset % 8);
stmpe_gpio_set(chip, offset, val);
......@@ -102,7 +104,7 @@ static int stmpe_gpio_direction_input(struct gpio_chip *chip,
{
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(chip);
struct stmpe *stmpe = stmpe_gpio->stmpe;
u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB] - (offset / 8);
u8 reg = stmpe->regs[STMPE_IDX_GPDR_LSB + (offset / 8)];
u8 mask = 1 << (offset % 8);
return stmpe_set_bits(stmpe, reg, mask, 0);
......@@ -173,10 +175,16 @@ static void stmpe_gpio_irq_sync_unlock(struct irq_data *d)
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(gc);
struct stmpe *stmpe = stmpe_gpio->stmpe;
int num_banks = DIV_ROUND_UP(stmpe->num_gpios, 8);
static const u8 regmap[] = {
[REG_RE] = STMPE_IDX_GPRER_LSB,
[REG_FE] = STMPE_IDX_GPFER_LSB,
[REG_IE] = STMPE_IDX_IEGPIOR_LSB,
static const u8 regmap[CACHE_NR_REGS][CACHE_NR_BANKS] = {
[REG_RE][LSB] = STMPE_IDX_GPRER_LSB,
[REG_RE][CSB] = STMPE_IDX_GPRER_CSB,
[REG_RE][MSB] = STMPE_IDX_GPRER_MSB,
[REG_FE][LSB] = STMPE_IDX_GPFER_LSB,
[REG_FE][CSB] = STMPE_IDX_GPFER_CSB,
[REG_FE][MSB] = STMPE_IDX_GPFER_MSB,
[REG_IE][LSB] = STMPE_IDX_IEGPIOR_LSB,
[REG_IE][CSB] = STMPE_IDX_IEGPIOR_CSB,
[REG_IE][MSB] = STMPE_IDX_IEGPIOR_MSB,
};
int i, j;
......@@ -194,7 +202,7 @@ static void stmpe_gpio_irq_sync_unlock(struct irq_data *d)
continue;
stmpe_gpio->oldregs[i][j] = new;
stmpe_reg_write(stmpe, stmpe->regs[regmap[i]] - j, new);
stmpe_reg_write(stmpe, stmpe->regs[regmap[i][j]], new);
}
}
......@@ -230,9 +238,9 @@ static void stmpe_dbg_show_one(struct seq_file *s,
struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(gc);
struct stmpe *stmpe = stmpe_gpio->stmpe;
const char *label = gpiochip_is_requested(gc, offset);
int num_banks = DIV_ROUND_UP(stmpe->num_gpios, 8);
bool val = !!stmpe_gpio_get(gc, offset);
u8 dir_reg = stmpe->regs[STMPE_IDX_GPDR_LSB] - (offset / 8);
u8 bank = offset / 8;
u8 dir_reg = stmpe->regs[STMPE_IDX_GPDR_LSB + bank];
u8 mask = 1 << (offset % 8);
int ret;
u8 dir;
......@@ -273,18 +281,16 @@ static void stmpe_dbg_show_one(struct seq_file *s,
case STMPE1601:
case STMPE2401:
case STMPE2403:
edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_MSB] +
num_banks - 1 - (offset / 8);
edge_det_reg = stmpe->regs[STMPE_IDX_GPEDR_LSB + bank];
ret = stmpe_reg_read(stmpe, edge_det_reg);
if (ret < 0)
return;
edge_det = !!(ret & mask);
case STMPE1801:
rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB] -
(offset / 8);
fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB] -
(offset / 8);
rise_reg = stmpe->regs[STMPE_IDX_GPRER_LSB + bank];
fall_reg = stmpe->regs[STMPE_IDX_GPFER_LSB + bank];
ret = stmpe_reg_read(stmpe, rise_reg);
if (ret < 0)
return;
......@@ -295,8 +301,7 @@ static void stmpe_dbg_show_one(struct seq_file *s,
fall = !!(ret & mask);
case STMPE801:
irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB] -
(offset / 8);
irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB + bank];
break;
default:
......@@ -378,8 +383,9 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
*/
if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801) {
stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
stmpe_reg_write(stmpe, stmpe->regs[STMPE_IDX_GPEDR_MSB]
+ i, status[i]);
stmpe_reg_write(stmpe,
stmpe->regs[STMPE_IDX_GPEDR_LSB + i],
status[i]);
}
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment