Commit 4420a561 authored by NeilBrown's avatar NeilBrown Committed by Greg Kroah-Hartman

staging: mt7621-dts: update ethernet settings.

The ethernet in mt7621 is now supported by
 drivers/net/ethernet/mediatek/

which provides support for the integrated switch through DSA.

This requires some devicetree changes, and particularly allows
a board dts to identify which switch ports are present.

The second CPU interface - gmac1 - doesn't work yet, so the device
tree information may not be correct.  The phy (which is present on the
gnubee-pc2) can negotiate and report connection speed etc, but no
traffic flows.

The gnubee-pc1 has two network ports which are 'black' and 'blue'.
There are connected to switch ports 0 and 4 respectively.
Signed-off-by: default avatarNeilBrown <neil@brown.name>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent bd31342f
......@@ -117,22 +117,6 @@ &pcie {
status = "okay";
};
&ethernet {
//mtd-mac-address = <&factory 0xe000>;
gmac1: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-handle = <&phy1>;
};
mdio-bus {
phy1: ethernet-phy@1 {
reg = <1>;
phy-mode = "rgmii";
};
};
};
&pinctrl {
state_default: pinctrl0 {
gpio {
......@@ -141,3 +125,16 @@ gpio {
};
};
};
&switch0 {
ports {
port@0 {
label = "ethblack";
status = "ok";
};
port@4 {
label = "ethblue";
status = "ok";
};
};
};
......@@ -372,16 +372,83 @@ ethernet: ethernet@1e100000 {
mediatek,ethsys = <&ethsys>;
mediatek,switch = <&gsw>;
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "rgmii";
fixed-link {
speed = <1000>;
full-duplex;
pause;
};
};
gmac1: mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
status = "off";
phy-mode = "rgmii";
phy-handle = <&phy5>;
};
mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
phy1f: ethernet-phy@1f {
reg = <0x1f>;
phy5: ethernet-phy@5 {
reg = <5>;
phy-mode = "rgmii";
};
switch0: switch0@0 {
compatible = "mediatek,mt7621";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
mediatek,mcm;
resets = <&rstctrl 2>;
reset-names = "mcm";
ports {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
port@0 {
status = "off";
reg = <0>;
label = "lan0";
};
port@1 {
status = "off";
reg = <1>;
label = "lan1";
};
port@2 {
status = "off";
reg = <2>;
label = "lan2";
};
port@3 {
status = "off";
reg = <3>;
label = "lan3";
};
port@4 {
status = "off";
reg = <4>;
label = "lan4";
};
port@6 {
reg = <6>;
label = "cpu";
ethernet = <&gmac0>;
phy-mode = "trgmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment