Commit 44c09201 authored by Matt LaPlante's avatar Matt LaPlante Committed by Adrian Bunk

more misc typo fixes

Signed-off-by: default avatarAdrian Bunk <bunk@stusta.de>
parent 09509603
......@@ -550,7 +550,7 @@ config ETRAX_IDE
select BLK_DEV_IDEDMA
help
Enable this to get support for ATA/IDE.
You can't use paralell ports or SCSI ports
You can't use parallel ports or SCSI ports
at the same time.
......@@ -744,7 +744,7 @@ config ETRAX_PA_CHANGEABLE_BITS
default "FF"
help
This is a bitmask with information of what bits in PA that a user
can change change the value on using ioctl's.
can change the value on using ioctl's.
Bit set = changeable.
You probably want 00 here.
......
......@@ -162,7 +162,7 @@ config ETRAX_SDRAM_GRP1_CONFIG
depends on ETRAX_ARCH_V32
default "0"
help
SDRAM configuration for group 1. The defult value is 0
SDRAM configuration for group 1. The default value is 0
because group 1 is not used in the default configuration,
described in the help for SDRAM_GRP0_CONFIG.
......
......@@ -161,8 +161,8 @@ config CLOCK_FREQ
frequency, it may or may not be the same as the external clock
crystal fitted to your board. Some processors have an internal
PLL and can have their frequency programmed at run time, others
use internal dividers. In gernal the kernel won't setup a PLL
if it is fitted (there are some expections). This value will be
use internal dividers. In general the kernel won't setup a PLL
if it is fitted (there are some exceptions). This value will be
specific to the exact CPU that you are using.
config CLOCK_DIV
......
......@@ -257,7 +257,7 @@ config UML_REAL_TIME_CLOCK
UML and spend long times with UML stopped at a breakpoint. In this
case, when UML is restarted, it will call the timer enough times to make
up for the time spent at the breakpoint. This could result in a
noticable lag. If this is a problem, then disable this option.
noticeable lag. If this is a problem, then disable this option.
endmenu
......
......@@ -310,7 +310,7 @@ config K8_NUMA
help
Enable K8 NUMA node topology detection. You should say Y here if
you have a multi processor AMD K8 system. This uses an old
method to read the NUMA configurtion directly from the builtin
method to read the NUMA configuration directly from the builtin
Northbridge of Opteron. It is recommended to use X86_64_ACPI_NUMA
instead, which also takes priority if both are compiled in.
......
......@@ -32,7 +32,7 @@ config JOYSTICK_ANALOG
module will be called analog.
config JOYSTICK_A3D
tristate "Assasin 3D and MadCatz Panther devices"
tristate "Assassin 3D and MadCatz Panther devices"
select GAMEPORT
help
Say Y here if you have an FPGaming or MadCatz controller using the
......
......@@ -1032,7 +1032,7 @@ config BEFS_FS
on files and directories, and database-like indeces on selected
attributes. (Also note that this driver doesn't make those features
available at this time). It is a 64 bit filesystem, so it supports
extremly large volumes and files.
extremely large volumes and files.
If you use this filesystem, you should also say Y to at least one
of the NLS (native language support) options below.
......
......@@ -104,7 +104,7 @@ config SPARSEMEM_STATIC
def_bool n
#
# Architectecture platforms which require a two level mem_section in SPARSEMEM
# Architecture platforms which require a two level mem_section in SPARSEMEM
# must select this option. This is usually for architecture platforms with
# an extremely sparse physical address space.
#
......
......@@ -64,7 +64,7 @@ config ASK_IP_FIB_HASH
config IP_FIB_TRIE
bool "FIB_TRIE"
---help---
Use new experimental LC-trie as FIB lookup algoritm.
Use new experimental LC-trie as FIB lookup algorithm.
This improves lookup performance if you have a large
number of routes.
......@@ -526,7 +526,7 @@ config TCP_CONG_HYBLA
---help---
TCP-Hybla is a sender-side only change that eliminates penalization of
long-RTT, large-bandwidth connections, like when satellite legs are
involved, expecially when sharing a common bottleneck with normal
involved, especially when sharing a common bottleneck with normal
terrestrial connections.
config TCP_CONG_VEGAS
......
......@@ -81,7 +81,7 @@ config IP_VS_PROTO_ESP
bool "ESP load balancing support"
depends on IP_VS
---help---
This option enables support for load balancing ESP (Encapsultion
This option enables support for load balancing ESP (Encapsulation
Security Payload) transport protocol. Say Y if unsure.
config IP_VS_PROTO_AH
......
......@@ -373,7 +373,7 @@ config IP_NF_TARGET_ULOG
daemon using netlink multicast sockets; unlike the LOG target
which can only be viewed through syslog.
The apropriate userspace logging daemon (ulogd) may be obtained from
The appropriate userspace logging daemon (ulogd) may be obtained from
<http://www.gnumonks.org/projects/ulogd/>
To compile it as a module, choose M here. If unsure, say N.
......
......@@ -112,7 +112,7 @@ config SECURITY_SELINUX_ENABLE_SECMARK_DEFAULT
your distribution will provide these and enable the new controls
in the kernel they also distribute.
Note that this option can be overriden at boot with the
Note that this option can be overridden at boot with the
selinux_compat_net parameter, and after boot via
/selinux/compat_net. See Documentation/kernel-parameters.txt
for details on this parameter.
......
......@@ -647,7 +647,7 @@ config SOUND_PSS
command line.
config PSS_MIXER
bool "Enable PSS mixer (Beethoven ADSP-16 and other compatibile)"
bool "Enable PSS mixer (Beethoven ADSP-16 and other compatible)"
depends on SOUND_PSS
help
Answer Y for Beethoven ADSP-16. You may try to say Y also for other
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment