arm64: dts: rockchip: Update powkiddy,rgb30 include to rk2023 DTSI

The Powkiddy RGB30 device is similar to the Anbernic RGxx3 series,
however there are several differences which require deleting nodes in
order to properly define the hardware. This was deemed unacceptable
for the RK2023, so instead create a common include file for the
Powkiddy RGB30 and the Powkiddy RK2023. The only notable difference
between these Powkiddy devices are the panel in use, the device
name, and the PLL_VPLL frequency necessary to support the different
panels.

Since the RK2023 was released on the market first, name the common
include file after it.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20231117202536.1387815-6-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

arch/arm64/boot/dts/rockchip/rk3566-powkiddy-rgb30.dts

@@ -5,67 +5,11 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/pinctrl/rockchip.h>
-#include "rk3566-anbernic-rg353x.dtsi"
+#include "rk3566-powkiddy-rk2023.dtsi"
 
 / {
 	model = "RGB30";
 	compatible = "powkiddy,rgb30", "rockchip,rk3566";
-
-	aliases {
-		mmc1 = &sdmmc0;
-		mmc2 = &sdmmc1;
-		mmc3 = &sdmmc2;
-	};
-
-	battery: battery {
-		compatible = "simple-battery";
-		charge-full-design-microamp-hours = <3151000>;
-		charge-term-current-microamp = <300000>;
-		constant-charge-current-max-microamp = <2000000>;
-		constant-charge-voltage-max-microvolt = <4250000>;
-		factory-internal-resistance-micro-ohms = <117000>;
-		voltage-max-design-microvolt = <4172000>;
-		voltage-min-design-microvolt = <3400000>;
-
-		ocv-capacity-celsius = <20>;
-		ocv-capacity-table-0 =  <4172000 100>, <4092000 95>, <4035000 90>, <3990000 85>,
-					<3939000 80>, <3895000 75>, <3852000 70>, <3807000 65>,
-					<3762000 60>, <3713000 55>, <3672000 50>, <3647000 45>,
-					<3629000 40>, <3613000 35>, <3598000 30>, <3578000 25>,
-					<3550000 20>, <3519000 15>, <3479000 10>, <3438000 5>,
-					<3400000 0>;
-	};
-
-	/*
-	 * Channels reversed for speakers. Headphones automatically switch via hardware when
-	 * detected with no ability to control output in software. Headphones appear to be mono
-	 * (each output channel receives all audio). No microphone support on 3.5mm jack.
-	 */
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "rk817_ext";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,mclk-fs = <256>;
-		simple-audio-card,widgets =
-			"Headphone", "Headphones";
-		simple-audio-card,routing =
-			"Headphones", "HPOL",
-			"Headphones", "HPOR";
-
-		simple-audio-card,codec {
-			sound-dai = <&rk817>;
-		};
-
-		simple-audio-card,cpu {
-			sound-dai = <&i2s1_8ch>;
-		};
-	};
-};
-
-/delete-node/ &adc_keys;
-
-&chosen {
-	/delete-property/ stdout-path;
 };
 
 &cru {
@@ -75,87 +19,21 @@ &cru {
 			       <200000000>, <292500000>;
 };
 
-&gpio_keys_control {
-	button-r1 {
-		gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
-		label = "TR";
-		linux,code = <BTN_TR>;
-	};
-
-	button-r2 {
-		gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
-		label = "TR2";
-		linux,code = <BTN_TR2>;
-	};
-};
-
-/delete-node/ &{/i2c@fdd40000/regulator@40};
-
-&i2c0 {
-	vdd_cpu: regulator@1c {
-		compatible = "tcs,tcs4525";
-		reg = <0x1c>;
-		fcs,suspend-voltage-selector = <1>;
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <712500>;
-		regulator-max-microvolt = <1390000>;
-		regulator-name = "vdd_cpu";
-		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc_sys>;
-		regulator-state-mem {
-			regulator-off-in-suspend;
+&dsi0 {
+	panel: panel@0 {
+		compatible = "powkiddy,rgb30-panel";
+		reg = <0>;
+		backlight = <&backlight>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_rst>;
+		reset-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&vcc3v3_lcd0_n>;
+		iovcc-supply = <&vcc3v3_lcd0_n>;
+
+		port {
+			mipi_in_panel: endpoint {
+				remote-endpoint = <&mipi_out_panel>;
+			};
 		};
 	};
 };
-
-/*
- * Device has 2 red LEDs instead of an amber and a red. Relabel LEDs as
- * red_led0 and red_led1.
- */
-/delete-node/ &{/pwm-leds/led-1};
-/delete-node/ &{/pwm-leds/led-2};
-
-&leds {
-	red_led0: led-1 {
-		color = <LED_COLOR_ID_RED>;
-		function = LED_FUNCTION_CHARGING;
-		max-brightness = <255>;
-		pwms = <&pwm7 0 25000 0>;
-	};
-
-	red_led1: led-2 {
-		color = <LED_COLOR_ID_RED>;
-		default-state = "off";
-		function = LED_FUNCTION_STATUS;
-		max-brightness = <255>;
-		pwms = <&pwm0 0 25000 0>;
-	};
-};
-
-&panel {
-	compatible = "powkiddy,rgb30-panel";
-	vcc-supply = <&vcc3v3_lcd0_n>;
-	iovcc-supply = <&vcc3v3_lcd0_n>;
-	/delete-property/ vdd-supply;
-};
-
-&pwm5 {
-	status = "disabled";
-};
-
-&rk817 {
-	rk817_charger: charger {
-		monitored-battery = <&battery>;
-		rockchip,resistor-sense-micro-ohms = <10000>;
-		rockchip,sleep-enter-current-microamp = <300000>;
-		rockchip,sleep-filter-current-microamp = <100000>;
-	};
-};
-
-/* There is no UART header visible on the board for this device. */
-&uart2 {
-	status = "disabled";
-};
-
-/delete-node/ &vibrator;