Commit 49ad712a authored by Hans de Goede's avatar Hans de Goede Committed by Andy Shevchenko

platform/x86: Add Intel AtomISP2 dummy / power-management driver

The Image Signal Processor found on Cherry Trail devices is brought up in
D0 state on devices which have camera sensors attached to it. The ISP will
not enter D3 state again without some massaging of its registers beforehand
and the ISP not being in D3 state blocks the SoC from entering S0ix modes.

There was a driver for the ISP in drivers/staging but that got removed
again because it never worked. It does not seem likely that a real
driver for the ISP will be added to the mainline kernel anytime soon.

This commit adds a dummy driver which contains the necessary magic from
the staging driver to powerdown the ISP, so that Cherry Trail devices where
the ISP is used will properly use S0ix modes when suspended.

Together with other recent S0ix related fixes this allows S0ix modes to
be entered on e.g. a Chuwi Hi8 Pro and a HP x2 210.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196915Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Reviewed-by: default avatarAlan Cox <alan@linux.intel.com>
Signed-off-by: default avatarAndy Shevchenko <andriy.shevchenko@linux.intel.com>
parent 4104916d
...@@ -7296,6 +7296,12 @@ L: alsa-devel@alsa-project.org (moderated for non-subscribers) ...@@ -7296,6 +7296,12 @@ L: alsa-devel@alsa-project.org (moderated for non-subscribers)
S: Supported S: Supported
F: sound/soc/intel/ F: sound/soc/intel/
INTEL ATOMISP2 DUMMY / POWER-MANAGEMENT DRIVER
M: Hans de Goede <hdegoede@redhat.com>
L: platform-driver-x86@vger.kernel.org
S: Maintained
F: drivers/platform/x86/intel_atomisp2_pm.c
INTEL C600 SERIES SAS CONTROLLER DRIVER INTEL C600 SERIES SAS CONTROLLER DRIVER
M: Intel SCU Linux support <intel-linux-scu@intel.com> M: Intel SCU Linux support <intel-linux-scu@intel.com>
M: Artur Paszkiewicz <artur.paszkiewicz@intel.com> M: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
......
...@@ -1274,6 +1274,18 @@ config I2C_MULTI_INSTANTIATE ...@@ -1274,6 +1274,18 @@ config I2C_MULTI_INSTANTIATE
To compile this driver as a module, choose M here: the module To compile this driver as a module, choose M here: the module
will be called i2c-multi-instantiate. will be called i2c-multi-instantiate.
config INTEL_ATOMISP2_PM
tristate "Intel AtomISP2 dummy / power-management driver"
depends on PCI && IOSF_MBI && PM
help
Power-management driver for Intel's Image Signal Processor found on
Bay and Cherry Trail devices. This dummy driver's sole purpose is to
turn the ISP off (put it in D3) to save power and to allow entering
of S0ix modes.
To compile this driver as a module, choose M here: the module
will be called intel_atomisp2_pm.
endif # X86_PLATFORM_DEVICES endif # X86_PLATFORM_DEVICES
config PMC_ATOM config PMC_ATOM
......
...@@ -95,3 +95,4 @@ obj-$(CONFIG_MLX_PLATFORM) += mlx-platform.o ...@@ -95,3 +95,4 @@ obj-$(CONFIG_MLX_PLATFORM) += mlx-platform.o
obj-$(CONFIG_INTEL_TURBO_MAX_3) += intel_turbo_max_3.o obj-$(CONFIG_INTEL_TURBO_MAX_3) += intel_turbo_max_3.o
obj-$(CONFIG_INTEL_CHTDC_TI_PWRBTN) += intel_chtdc_ti_pwrbtn.o obj-$(CONFIG_INTEL_CHTDC_TI_PWRBTN) += intel_chtdc_ti_pwrbtn.o
obj-$(CONFIG_I2C_MULTI_INSTANTIATE) += i2c-multi-instantiate.o obj-$(CONFIG_I2C_MULTI_INSTANTIATE) += i2c-multi-instantiate.o
obj-$(CONFIG_INTEL_ATOMISP2_PM) += intel_atomisp2_pm.o
// SPDX-License-Identifier: GPL-2.0
/*
* Dummy driver for Intel's Image Signal Processor found on Bay and Cherry
* Trail devices. The sole purpose of this driver is to allow the ISP to
* be put in D3.
*
* Copyright (C) 2018 Hans de Goede <hdegoede@redhat.com>
*
* Based on various non upstream patches for ISP support:
* Copyright (C) 2010-2017 Intel Corporation. All rights reserved.
* Copyright (c) 2010 Silicon Hive www.siliconhive.com.
*/
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/mod_devicetable.h>
#include <linux/pci.h>
#include <linux/pm_runtime.h>
#include <asm/iosf_mbi.h>
/* PCI configuration regs */
#define PCI_INTERRUPT_CTRL 0x9c
#define PCI_CSI_CONTROL 0xe8
#define PCI_CSI_CONTROL_PORTS_OFF_MASK 0x7
/* IOSF BT_MBI_UNIT_PMC regs */
#define ISPSSPM0 0x39
#define ISPSSPM0_ISPSSC_OFFSET 0
#define ISPSSPM0_ISPSSC_MASK 0x00000003
#define ISPSSPM0_ISPSSS_OFFSET 24
#define ISPSSPM0_ISPSSS_MASK 0x03000000
#define ISPSSPM0_IUNIT_POWER_ON 0x0
#define ISPSSPM0_IUNIT_POWER_OFF 0x3
static int isp_probe(struct pci_dev *dev, const struct pci_device_id *id)
{
unsigned long timeout;
u32 val;
pci_write_config_dword(dev, PCI_INTERRUPT_CTRL, 0);
/*
* MRFLD IUNIT DPHY is located in an always-power-on island
* MRFLD HW design need all CSI ports are disabled before
* powering down the IUNIT.
*/
pci_read_config_dword(dev, PCI_CSI_CONTROL, &val);
val |= PCI_CSI_CONTROL_PORTS_OFF_MASK;
pci_write_config_dword(dev, PCI_CSI_CONTROL, val);
/* Write 0x3 to ISPSSPM0 bit[1:0] to power off the IUNIT */
iosf_mbi_modify(BT_MBI_UNIT_PMC, MBI_REG_READ, ISPSSPM0,
ISPSSPM0_IUNIT_POWER_OFF, ISPSSPM0_ISPSSC_MASK);
/*
* There should be no IUNIT access while power-down is
* in progress HW sighting: 4567865
* Wait up to 50 ms for the IUNIT to shut down.
*/
timeout = jiffies + msecs_to_jiffies(50);
while (1) {
/* Wait until ISPSSPM0 bit[25:24] shows 0x3 */
iosf_mbi_read(BT_MBI_UNIT_PMC, MBI_REG_READ, ISPSSPM0, &val);
val = (val & ISPSSPM0_ISPSSS_MASK) >> ISPSSPM0_ISPSSS_OFFSET;
if (val == ISPSSPM0_IUNIT_POWER_OFF)
break;
if (time_after(jiffies, timeout)) {
dev_err(&dev->dev, "IUNIT power-off timeout.\n");
return -EBUSY;
}
usleep_range(1000, 2000);
}
pm_runtime_allow(&dev->dev);
pm_runtime_put_sync_suspend(&dev->dev);
return 0;
}
static void isp_remove(struct pci_dev *dev)
{
pm_runtime_get_sync(&dev->dev);
pm_runtime_forbid(&dev->dev);
}
static int isp_pci_suspend(struct device *dev)
{
return 0;
}
static int isp_pci_resume(struct device *dev)
{
return 0;
}
static UNIVERSAL_DEV_PM_OPS(isp_pm_ops, isp_pci_suspend,
isp_pci_resume, NULL);
static const struct pci_device_id isp_id_table[] = {
{ PCI_VDEVICE(INTEL, 0x22b8), },
{ 0, }
};
MODULE_DEVICE_TABLE(pci, isp_id_table);
static struct pci_driver isp_pci_driver = {
.name = "intel_atomisp2_pm",
.id_table = isp_id_table,
.probe = isp_probe,
.remove = isp_remove,
.driver.pm = &isp_pm_ops,
};
module_pci_driver(isp_pci_driver);
MODULE_DESCRIPTION("Intel AtomISP2 dummy / power-management drv (for suspend)");
MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
MODULE_LICENSE("GPL v2");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment