net: hns: Some registers use wrong address according to the datasheet.

According to the hip06 datasheet:
1.Six registers use wrong address:
  RCB_COM_SF_CFG_INTMASK_RING
  RCB_COM_SF_CFG_RING_STS
  RCB_COM_SF_CFG_RING
  RCB_COM_SF_CFG_INTMASK_BD
  RCB_COM_SF_CFG_BD_RINT_STS
  DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
  0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
  is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
  overwrite

These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns/hns_dsaf_reg.h

@@ -176,7 +176,7 @@
 #define DSAF_INODE_IN_DATA_STP_DISC_0_REG	0x1A50
 #define DSAF_INODE_GE_FC_EN_0_REG		0x1B00
 #define DSAF_INODE_VC0_IN_PKT_NUM_0_REG		0x1B50
-#define DSAF_INODE_VC1_IN_PKT_NUM_0_REG		0x1C00
+#define DSAF_INODE_VC1_IN_PKT_NUM_0_REG		0x103C
 #define DSAF_INODE_IN_PRIO_PAUSE_BASE_REG	0x1C00
 #define DSAF_INODE_IN_PRIO_PAUSE_BASE_OFFSET	0x100
 #define DSAF_INODE_IN_PRIO_PAUSE_OFFSET		0x50
@@ -404,11 +404,11 @@
 #define RCB_ECC_ERR_ADDR4_REG			0x460
 #define RCB_ECC_ERR_ADDR5_REG			0x464
 
-#define RCB_COM_SF_CFG_INTMASK_RING		0x480
-#define RCB_COM_SF_CFG_RING_STS			0x484
-#define RCB_COM_SF_CFG_RING			0x488
-#define RCB_COM_SF_CFG_INTMASK_BD		0x48C
-#define RCB_COM_SF_CFG_BD_RINT_STS		0x470
+#define RCB_COM_SF_CFG_INTMASK_RING		0x470
+#define RCB_COM_SF_CFG_RING_STS			0x474
+#define RCB_COM_SF_CFG_RING			0x478
+#define RCB_COM_SF_CFG_INTMASK_BD		0x47C
+#define RCB_COM_SF_CFG_BD_RINT_STS		0x480
 #define RCB_COM_RCB_RD_BD_BUSY			0x490
 #define RCB_COM_RCB_FBD_CRT_EN			0x494
 #define RCB_COM_AXI_WR_ERR_INTMASK		0x498