arm64: dts: qcom: msm8916-samsung-gt5: Add sound and modem

Enable sound and modem for the Samsung Galaxy Tab A 2015 tablets.
The setup is similar to most MSM8916 devices, i.e.:

 - QDSP6 audio
 - Headphones/microphones via digital/analog codec in
   MSM8916/PM8916. Earpiece exists on samsung-gt58 only.
 - WWAN Internet via BAM-DMUX

except:

 - gt510: Stereo Maxim MAX98357A codecs for speaker on Quaternary MI2S
 - gt58: Mono NXP TFA9895 codec for speaker on Quaternary MI2S
   - For some reason connected to GPIOs where no hardware I2C
     controller is available -> need to use i2c-gpio
- Samsung-specific audio jack detection (not supported yet)
Signed-off-by: Jasper Korten <jja2000@gmail.com>
Co-developed-by: Siddharth Manthan <siddharth.manthan@gmail.com>
Signed-off-by: Siddharth Manthan <siddharth.manthan@gmail.com>
Co-developed-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
[Stephan: Add consistent commit message, minor refactoring]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-12-61b684be55c0@gerhold.netSigned-off-by: Bjorn Andersson <andersson@kernel.org>

arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi

@@ -3,9 +3,12 @@
 /dts-v1/;
 
 #include "msm8916-pm8916.dtsi"
+#include "msm8916-modem-qdsp6.dtsi"
+
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
 
 / {
 	aliases {
@@ -116,6 +119,29 @@ &blsp_uart2 {
 	status = "okay";
 };
 
+/*
+ * For some reason the speaker amplifier is connected to the second SD line
+ * (MI2S_2_D1) instead of the first (MI2S_2_D0). This must be configured in the
+ * device tree, otherwise audio will seemingly play fine on the wrong SD line
+ * but the speaker stays silent.
+ *
+ * When routing audio via QDSP6 (the default) the &lpass node is reserved and
+ * the definitions from &q6afedai are used. When the modem is disabled audio can
+ * be alternatively routed directly to the LPASS hardware with reduced latency.
+ * The definitions for &lpass are here for completeness to simplify changing the
+ * setup with minor changes to the DT (either manually or with DT overlays).
+ */
+&lpass {
+	dai-link@3 {
+		reg = <MI2S_QUATERNARY>;
+		qcom,playback-sd-lines = <1>;
+	};
+};
+
+&mpss_mem {
+	reg = <0x0 0x86800000 0x0 0x5400000>;
+};
+
 &pm8916_resin {
 	linux,code = <KEY_VOLUMEDOWN>;
 	status = "okay";
@@ -133,6 +159,13 @@ &pm8916_usbin {
 	status = "okay";
 };
 
+&q6afedai {
+	dai@22 {
+		reg = <QUATERNARY_MI2S_RX>;
+		qcom,sd-lines = <1>;
+	};
+};
+
 &sdhc_1 {
 	status = "okay";
 };
@@ -147,6 +180,27 @@ &sdhc_2 {
 	status = "okay";
 };
 
+&sound {
+	audio-routing =
+		"AMIC1", "MIC BIAS External1",
+		"AMIC2", "MIC BIAS Internal2",
+		"AMIC3", "MIC BIAS External1";
+
+	sound_link_backend2: backend2-dai-link {
+		link-name = "Quaternary MI2S";
+
+		cpu {
+			sound-dai = <&q6afedai QUATERNARY_MI2S_RX>;
+		};
+		platform {
+			sound-dai = <&q6routing>;
+		};
+		codec {
+			sound-dai = <&speaker_codec>;
+		};
+	};
+};
+
 &usb {
 	dr_mode = "peripheral";
 	extcon = <&pm8916_usbin>;

arch/arm64/boot/dts/qcom/msm8916-samsung-gt510.dts

@@ -9,6 +9,14 @@ / {
 	compatible = "samsung,gt510", "qcom,msm8916";
 	chassis-type = "tablet";
 
+	speaker_codec: audio-codec {
+		compatible = "maxim,max98357a";
+		sdmode-gpios = <&tlmm 55 GPIO_ACTIVE_HIGH>;
+		#sound-dai-cells = <0>;
+		pinctrl-0 = <&audio_sdmode_default>;
+		pinctrl-names = "default";
+	};
+
 	clk_pwm: pwm {
 		compatible = "clk-pwm";
 		#pwm-cells = <2>;
@@ -146,7 +154,21 @@ &mdss_dsi0_out {
 	remote-endpoint = <&panel_in>;
 };
 
+&sound {
+	model = "samsung-gt510";
+	pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
+	pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
+	pinctrl-names = "default", "sleep";
+};
+
 &tlmm {
+	audio_sdmode_default: audio-sdmode-default-state {
+		pins = "gpio55";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	buckbooster_en_default: buckbooster-en-default-state {
 		pins = "gpio51";
 		function = "gpio";

arch/arm64/boot/dts/qcom/msm8916-samsung-gt58.dts

@@ -35,6 +35,26 @@ reg_vdd_tsp: regulator-vdd-tsp {
 		pinctrl-names = "default";
 	};
 
+	i2c-amplifier {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 55 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 56 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&amp_i2c_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		speaker_codec: audio-codec@34 {
+			compatible = "nxp,tfa9895";
+			reg = <0x34>;
+			vddd-supply = <&pm8916_l5>;
+			sound-name-prefix = "Speaker";
+			#sound-dai-cells = <0>;
+		};
+	};
+
 	vibrator {
 		compatible = "gpio-vibrator";
 		enable-gpios = <&tlmm 76 GPIO_ACTIVE_HIGH>;
@@ -98,7 +118,21 @@ &mdss_dsi0_out {
 	remote-endpoint = <&panel_in>;
 };
 
+&sound {
+	model = "samsung-a2015";
+	pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default &secondary_mic_default>;
+	pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep &secondary_mic_default>;
+	pinctrl-names = "default", "sleep";
+};
+
 &tlmm {
+	amp_i2c_default: amp-i2c-default-state {
+		pins = "gpio55", "gpio56";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	buckbooster_en_default: buckbooster-en-default-state {
 		pins = "gpio8";
 		function = "gpio";
@@ -127,6 +161,14 @@ reg_tsp_en_default: reg-tsp-en-default-state {
 		bias-disable;
 	};
 
+	secondary_mic_default: secondary-mic-default-state {
+		pins = "gpio98";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
 	tsp_int_default: tsp-int-default-state {
 		pins = "gpio13";
 		function = "gpio";