Merge tag 'amlogic-dt64' of...

Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt64

Amlogic DT 64-bit changes for v4.8
- add pinctrl driver and pins for several devices
- add reset driver

* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: amlogic: Enable Reset Controller on GXBB-based platforms
  ARM64: dts: amlogic: gxbb: add ethernet
  ARM64: dts: amlogic: gxbb: pinctrl: add/update UART
  ARM64: dts: amlogic: add pins for EMMC, SD
  ARM64: dts: amlogic: Enable pin controller on GXBB-based platforms
  documentation: Add compatibles for Amlogic Meson GXBB pin controllers
  ARM64: dts: amlogic: Add hiu and periphs buses
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt

@@ -5,6 +5,8 @@ Required properties for the root node:
 		      "amlogic,meson8b-cbus-pinctrl"
 		      "amlogic,meson8-aobus-pinctrl"
 		      "amlogic,meson8b-aobus-pinctrl"
+		      "amlogic,meson-gxbb-periphs-pinctrl"
+		      "amlogic,meson-gxbb-aobus-pinctrl"
  - reg: address and size of registers controlling irq functionality
 
 === GPIO sub-nodes ===

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

@@ -45,6 +45,7 @@
 /dts-v1/;
 
 #include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
@@ -62,8 +63,27 @@ memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		blue {
+			label = "c2:blue:alive";
+			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
 };
 
 &uart_AO {
 	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
 };
+

arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi

@@ -62,4 +62,13 @@ memory@0 {
 /* This UART is brought out to the DB9 connector */
 &uart_AO {
 	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
 };
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+};
+

arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi

@@ -56,4 +56,7 @@ chosen {
 
 &uart_AO {
 	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+
 };

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -43,6 +43,8 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/meson-gxbb-gpio.h>
+#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
 
 / {
 	compatible = "amlogic,meson-gxbb";
@@ -129,13 +131,35 @@ cbus: cbus@c1100000 {
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
 
+			reset: reset-controller@4404 {
+				compatible = "amlogic,meson-gxbb-reset";
+				reg = <0x0 0x04404 0x0 0x20>;
+				#reset-cells = <1>;
+			};
+
 			uart_A: serial@84c0 {
 				compatible = "amlogic,meson-uart";
-				reg = <0x0 0x084c0 0x0 0x14>;
+				reg = <0x0 0x84c0 0x0 0x14>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
 				clocks = <&xtal>;
 				status = "disabled";
 			};
+
+			uart_B: serial@84dc {
+				compatible = "amlogic,meson-uart";
+				reg = <0x0 0x84dc 0x0 0x14>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>;
+				status = "disabled";
+			};
+
+			uart_C: serial@8700 {
+				compatible = "amlogic,meson-uart";
+				reg = <0x0 0x8700 0x0 0x14>;
+				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>;
+				status = "disabled";
+			};
 		};
 
 		gic: interrupt-controller@c4301000 {
@@ -158,6 +182,29 @@ aobus: aobus@c8100000 {
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
 
+			pinctrl_aobus: pinctrl@14 {
+				compatible = "amlogic,meson-gxbb-aobus-pinctrl";
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges;
+
+				gpio_ao: bank@14 {
+					reg = <0x0 0x00014 0x0 0x8>,
+					      <0x0 0x0002c 0x0 0x4>,
+					      <0x0 0x00024 0x0 0x8>;
+					reg-names = "mux", "pull", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				uart_ao_a_pins: uart_ao_a {
+					mux {
+						groups = "uart_tx_ao_a", "uart_rx_ao_a";
+						function = "uart_ao";
+					};
+				};
+			};
+
 			uart_AO: serial@4c0 {
 				compatible = "amlogic,meson-uart";
 				reg = <0x0 0x004c0 0x0 0x14>;
@@ -167,6 +214,104 @@ uart_AO: serial@4c0 {
 			};
 		};
 
+		periphs: periphs@c8834000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xc8834000 0x0 0x2000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
+
+			pinctrl_periphs: pinctrl@4b0 {
+				compatible = "amlogic,meson-gxbb-periphs-pinctrl";
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges;
+
+				gpio: bank@4b0 {
+					reg = <0x0 0x004b0 0x0 0x28>,
+					      <0x0 0x004e8 0x0 0x14>,
+					      <0x0 0x00120 0x0 0x14>,
+					      <0x0 0x00430 0x0 0x40>;
+					reg-names = "mux", "pull", "pull-enable", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				emmc_pins: emmc {
+					mux {
+						groups = "emmc_nand_d07",
+						       "emmc_cmd",
+						       "emmc_clk";
+						function = "emmc";
+					};
+				};
+
+				sdcard_pins: sdcard {
+					mux {
+						groups = "sdcard_d0",
+						       "sdcard_d1",
+						       "sdcard_d2",
+						       "sdcard_d3",
+						       "sdcard_cmd",
+						       "sdcard_clk";
+						function = "sdcard";
+					};
+				};
+
+				uart_a_pins: uart_a {
+					mux {
+						groups = "uart_tx_a",
+						       "uart_rx_a";
+						function = "uart_a";
+					};
+				};
+
+				uart_b_pins: uart_b {
+					mux {
+						groups = "uart_tx_b",
+						       "uart_rx_b";
+						function = "uart_b";
+					};
+				};
+
+				uart_c_pins: uart_c {
+					mux {
+						groups = "uart_tx_c",
+						       "uart_rx_c";
+						function = "uart_c";
+					};
+				};
+
+				eth_pins: eth_c {
+					mux {
+						groups = "eth_mdio",
+						       "eth_mdc",
+						       "eth_clk_rx_clk",
+						       "eth_rx_dv",
+						       "eth_rxd0",
+						       "eth_rxd1",
+						       "eth_rxd2",
+						       "eth_rxd3",
+						       "eth_rgmii_tx_clk",
+						       "eth_tx_en",
+						       "eth_txd0",
+						       "eth_txd1",
+						       "eth_txd2",
+						       "eth_txd3";
+						function = "eth";
+					};
+				};
+			};
+		};
+
+		hiubus: hiubus@c883c000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xc883c000 0x0 0x2000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
+		};
+
 		apb: apb@d0000000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xd0000000 0x0 0x200000>;
@@ -174,5 +319,17 @@ apb: apb@d0000000 {
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
 		};
+
+		ethmac: ethernet@c9410000 {
+			compatible = "amlogic,meson6-dwmac", "snps,dwmac";
+			reg = <0x0 0xc9410000 0x0 0x10000
+			       0x0 0xc8834540 0x0 0x4>;
+			interrupts = <0 8 1>;
+			interrupt-names = "macirq";
+			clocks = <&xtal>;
+			clock-names = "stmmaceth";
+			phy-mode = "rgmii";
+			status = "disabled";
+		};
 	};
 };