Commit 4fd0690b authored by Rajanikanth H.V's avatar Rajanikanth H.V Committed by Greg Kroah-Hartman

serial: pl011: implement workaround for CTS clear event issue

Problem Observed:
- interrupt status is set by rising or falling edge on CTS line
- interrupt status is cleared on a .0. to .1. transition of the
  interrupt-clear register bit 1.
- interrupt-clear register is reset by hardware once the interrupt
  status is .0..
  Remark: It seems not possible to read this register back by the
  CPU though, but internally this register exists.
- when simultaneous set and reset event on the interrupt status
  happens, then the set-event has priority and the status remains
  .1.. As a result the interrupt-clear register is not reset to
  .0., and no new .0. to .1. transition can be detected on it when
  writing a .1. to it.
  This implies race condition, the clear must be performed at least
  one UARTCLK the riding edge of CTS RIS interrupt.

Fix:
  Instead of resetting UART as done in commit
  c16d51a3
  "amba pl011: workaround for uart registers lockup" do the
  following:

  write .0. and then  .1. to the interrupt-clear register to make
  sure that this transition is detected. According to the datasheet
  writing a .0. does not have any effect, but actually it allows to
  reset the internal interrupt-clear register.

  Take into account:
  The .0. needs to last at least for one clk_uart clock period
  (~ 38 MHz, 26.08ns)

This way we can do away with the tasklet and keep only a tiny
fix triggered by the variant flag introduced in this patch.
Signed-off-by: default avatarGuillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: default avatarChristophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: default avatarMatthias Locher  <Matthias.Locher@stericsson.com>
Signed-off-by: default avatarRajanikanth H.V <rajanikanth.hv@stericsson.com>
Reviewed-by: default avatarSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent e695b286
......@@ -67,30 +67,6 @@
#define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE)
#define UART_DUMMY_DR_RX (1 << 16)
#define UART_WA_SAVE_NR 14
static void pl011_lockup_wa(unsigned long data);
static const u32 uart_wa_reg[UART_WA_SAVE_NR] = {
ST_UART011_DMAWM,
ST_UART011_TIMEOUT,
ST_UART011_LCRH_RX,
UART011_IBRD,
UART011_FBRD,
ST_UART011_LCRH_TX,
UART011_IFLS,
ST_UART011_XFCR,
ST_UART011_XON1,
ST_UART011_XON2,
ST_UART011_XOFF1,
ST_UART011_XOFF2,
UART011_CR,
UART011_IMSC
};
static u32 uart_wa_regdata[UART_WA_SAVE_NR];
static DECLARE_TASKLET(pl011_lockup_tlet, pl011_lockup_wa, 0);
/* There is by now at least one vendor with differing details, so handle it */
struct vendor_data {
unsigned int ifls;
......@@ -100,6 +76,7 @@ struct vendor_data {
bool oversampling;
bool interrupt_may_hang; /* vendor-specific */
bool dma_threshold;
bool cts_event_workaround;
};
static struct vendor_data vendor_arm = {
......@@ -109,6 +86,7 @@ static struct vendor_data vendor_arm = {
.lcrh_rx = UART011_LCRH,
.oversampling = false,
.dma_threshold = false,
.cts_event_workaround = false,
};
static struct vendor_data vendor_st = {
......@@ -119,6 +97,7 @@ static struct vendor_data vendor_st = {
.oversampling = true,
.interrupt_may_hang = true,
.dma_threshold = true,
.cts_event_workaround = true,
};
static struct uart_amba_port *amba_ports[UART_NR];
......@@ -1054,69 +1033,6 @@ static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
#define pl011_dma_flush_buffer NULL
#endif
/*
* pl011_lockup_wa
* This workaround aims to break the deadlock situation
* when after long transfer over uart in hardware flow
* control, uart interrupt registers cannot be cleared.
* Hence uart transfer gets blocked.
*
* It is seen that during such deadlock condition ICR
* don't get cleared even on multiple write. This leads
* pass_counter to decrease and finally reach zero. This
* can be taken as trigger point to run this UART_BT_WA.
*
*/
static void pl011_lockup_wa(unsigned long data)
{
struct uart_amba_port *uap = amba_ports[0];
void __iomem *base = uap->port.membase;
struct circ_buf *xmit = &uap->port.state->xmit;
struct tty_struct *tty = uap->port.state->port.tty;
int buf_empty_retries = 200;
int loop;
/* Stop HCI layer from submitting data for tx */
tty->hw_stopped = 1;
while (!uart_circ_empty(xmit)) {
if (buf_empty_retries-- == 0)
break;
udelay(100);
}
/* Backup registers */
for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
uart_wa_regdata[loop] = readl(base + uart_wa_reg[loop]);
/* Disable UART so that FIFO data is flushed out */
writew(0x00, uap->port.membase + UART011_CR);
/* Soft reset UART module */
if (uap->port.dev->platform_data) {
struct amba_pl011_data *plat;
plat = uap->port.dev->platform_data;
if (plat->reset)
plat->reset();
}
/* Restore registers */
for (loop = 0; loop < UART_WA_SAVE_NR; loop++)
writew(uart_wa_regdata[loop] ,
uap->port.membase + uart_wa_reg[loop]);
/* Initialise the old status of the modem signals */
uap->old_status = readw(uap->port.membase + UART01x_FR) &
UART01x_FR_MODEM_ANY;
if (readl(base + UART011_MIS) & 0x2)
printk(KERN_EMERG "UART_BT_WA: ***FAILED***\n");
/* Start Tx/Rx */
tty->hw_stopped = 0;
}
static void pl011_stop_tx(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
......@@ -1245,12 +1161,26 @@ static irqreturn_t pl011_int(int irq, void *dev_id)
unsigned long flags;
unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
int handled = 0;
unsigned int dummy_read;
spin_lock_irqsave(&uap->port.lock, flags);
status = readw(uap->port.membase + UART011_MIS);
if (status) {
do {
if (uap->vendor->cts_event_workaround) {
/* workaround to make sure that all bits are unlocked.. */
writew(0x00, uap->port.membase + UART011_ICR);
/*
* WA: introduce 26ns(1 uart clk) delay before W1C;
* single apb access will incur 2 pclk(133.12Mhz) delay,
* so add 2 dummy reads
*/
dummy_read = readw(uap->port.membase + UART011_ICR);
dummy_read = readw(uap->port.membase + UART011_ICR);
}
writew(status & ~(UART011_TXIS|UART011_RTIS|
UART011_RXIS),
uap->port.membase + UART011_ICR);
......@@ -1267,11 +1197,8 @@ static irqreturn_t pl011_int(int irq, void *dev_id)
if (status & UART011_TXIS)
pl011_tx_chars(uap);
if (pass_counter-- == 0) {
if (uap->interrupt_may_hang)
tasklet_schedule(&pl011_lockup_tlet);
if (pass_counter-- == 0)
break;
}
status = readw(uap->port.membase + UART011_MIS);
} while (status != 0);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment