Merge branch 'regulator-4.20' into regulator-next

Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt

-* ROHM BD71837 Power Management Integrated Circuit bindings
+* ROHM BD71837 and BD71847 Power Management Integrated Circuit bindings
 
-BD71837MWV is a programmable Power Management IC for powering single-core,
-dual-core, and quad-core SoCs such as NXP-i.MX 8M. It is optimized for
-low BOM cost and compact solution footprint. It integrates 8 Buck
-egulators and 7 LDOs to provide all the power rails required by the SoC and
-the commonly used peripherals.
+BD71837MWV and BD71847MWV are programmable Power Management ICs for powering
+single-core, dual-core, and quad-core SoCs such as NXP-i.MX 8M. They are
+optimized for low BOM cost and compact solution footprint. BD71837MWV
+integrates 8 Buck regulators and 7 LDOs. BD71847MWV contains 6 Buck regulators
+and 6 LDOs.
 
-Datasheet for PMIC is available at:
+Datasheet for BD71837 is available at:
 https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e
 
 Required properties:
- - compatible		: Should be "rohm,bd71837".
+ - compatible		: Should be "rohm,bd71837" for bd71837
+				    "rohm,bd71847" for bd71847.
  - reg			: I2C slave address.
  - interrupt-parent	: Phandle to the parent interrupt controller.
  - interrupts		: The interrupt line the device is connected to.

Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt

@@ -26,6 +26,7 @@ Regulator nodes are identified by their compatible:
 		    "qcom,rpm-pm8998-regulators"
 		    "qcom,rpm-pma8084-regulators"
 		    "qcom,rpm-pmi8998-regulators"
+		    "qcom,rpm-pms405-regulators"
 
 - vdd_s1-supply:
 - vdd_s2-supply:
@@ -188,6 +189,24 @@ Regulator nodes are identified by their compatible:
 	Definition: reference to regulator supplying the input pin, as
 		    described in the data sheet
 
+- vdd_s1-supply:
+- vdd_s2-supply:
+- vdd_s3-supply:
+- vdd_s4-supply:
+- vdd_s5-supply:
+- vdd_l1_l2-supply:
+- vdd_l3_l8-supply:
+- vdd_l4-supply:
+- vdd_l5_l6-supply:
+- vdd_l7-supply:
+- vdd_l3_l8-supply:
+- vdd_l9-supply:
+- vdd_l10_l11_l12_l13-supply:
+	Usage: optional (pms405 only)
+	Value type: <phandle>
+	Definition: reference to regulator supplying the input pin, as
+		    described in the data sheet
+
 The regulator node houses sub-nodes for each regulator within the device. Each
 sub-node is identified using the node's name, with valid values listed for each
 of the pmics below.
@@ -222,6 +241,10 @@ pma8084:
 pmi8998:
 	bob
 
+pms405:
+	s1, s2, s3, s4, s5, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12,
+	l13
+
 The content of each sub-node is defined by the standard binding for regulators -
 see regulator.txt.
 

Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt

-ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings
+ROHM BD71837 and BD71847 Power Management Integrated Circuit regulator bindings
 
 Required properties:
- - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7"
+ - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" for
+                   BD71837. For BD71847 names should be "buck1", ..., "buck6"
+		   and "ldo1", ..., "ldo6"
 
 List of regulators provided by this controller. BD71837 regulators node
 should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at
@@ -16,10 +18,14 @@ disabled by driver at startup. LDO5 and LDO6 are supplied by those and
 if they are disabled at startup the voltage monitoring for LDO5/LDO6 will
 cause PMIC to reset.
 
-The valid names for regulator nodes are:
+The valid names for BD71837 regulator nodes are:
 BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8
 LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7
 
+The valid names for BD71847 regulator nodes are:
+BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6
+LDO1, LDO2, LDO3, LDO4, LDO5, LDO6
+
 Optional properties:
 - Any optional property defined in bindings/regulator/regulator.txt
 

Documentation/devicetree/bindings/regulator/st,stpmic1-regulator.txt

+STMicroelectronics STPMIC1 Voltage regulators
+
+Regulator Nodes are optional depending on needs.
+
+Available Regulators in STPMIC1 device are:
+  - buck1 for Buck BUCK1
+  - buck2 for Buck BUCK2
+  - buck3 for Buck BUCK3
+  - buck4 for Buck BUCK4
+  - ldo1 for LDO LDO1
+  - ldo2 for LDO LDO2
+  - ldo3 for LDO LDO3
+  - ldo4 for LDO LDO4
+  - ldo5 for LDO LDO5
+  - ldo6 for LDO LDO6
+  - vref_ddr for LDO Vref DDR
+  - boost for Buck BOOST
+  - pwr_sw1 for VBUS_OTG switch
+  - pwr_sw2 for SW_OUT switch
+
+Switches are fixed voltage regulators with only enable/disable capability.
+
+Optional properties:
+- st,mask-reset: mask reset for this regulator: the regulator configuration
+  is maintained during pmic reset.
+- regulator-pull-down: enable high pull down
+  if not specified light pull down is used
+- regulator-over-current-protection:
+    if set, all regulators are switched off in case of over-current detection
+    on this regulator,
+    if not set, the driver only sends an over-current event.
+- interrupt-parent: phandle to the parent interrupt controller
+- interrupts: index of current limit detection interrupt
+- <regulator>-supply: phandle to the parent supply/regulator node
+	each regulator supply can be described except vref_ddr.
+
+Example:
+regulators {
+	compatible = "st,stpmic1-regulators";
+
+	ldo6-supply = <&v3v3>;
+
+	vdd_core: buck1 {
+		regulator-name = "vdd_core";
+		interrupts = <IT_CURLIM_BUCK1 0>;
+		interrupt-parent = <&pmic>;
+		st,mask-reset;
+		regulator-pull-down;
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	v3v3: buck4 {
+		regulator-name = "v3v3";
+		interrupts = <IT_CURLIM_BUCK4 0>;
+		interrupt-parent = <&mypmic>;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	v1v8: ldo6 {
+		regulator-name = "v1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-over-current-protection;
+	};
+};

arch/arm/mach-imx/mach-mx21ads.c

@@ -18,6 +18,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/physmap.h>
 #include <linux/gpio/driver.h>
+#include <linux/gpio/machine.h>
 #include <linux/gpio.h>
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
@@ -175,6 +176,7 @@ static struct resource mx21ads_mmgpio_resource =
 	DEFINE_RES_MEM_NAMED(MX21ADS_IO_REG, SZ_2, "dat");
 
 static struct bgpio_pdata mx21ads_mmgpio_pdata = {
+	.label	= "mx21ads-mmgpio",
 	.base	= MX21ADS_MMGPIO_BASE,
 	.ngpio	= 16,
 };
@@ -203,7 +205,6 @@ static struct regulator_init_data mx21ads_lcd_regulator_init_data = {
 static struct fixed_voltage_config mx21ads_lcd_regulator_pdata = {
 	.supply_name	= "LCD",
 	.microvolts	= 3300000,
-	.gpio		= MX21ADS_IO_LCDON,
 	.enable_high	= 1,
 	.init_data	= &mx21ads_lcd_regulator_init_data,
 };
@@ -216,6 +217,14 @@ static struct platform_device mx21ads_lcd_regulator = {
 	},
 };
 
+static struct gpiod_lookup_table mx21ads_lcd_regulator_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
+	.table = {
+		GPIO_LOOKUP("mx21ads-mmgpio", 9, NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /*
  * Connected is a portrait Sharp-QVGA display
  * of type: LQ035Q7DB02
@@ -311,6 +320,7 @@ static void __init mx21ads_late_init(void)
 {
 	imx21_add_mxc_mmc(0, &mx21ads_sdhc_pdata);
 
+	gpiod_add_lookup_table(&mx21ads_lcd_regulator_gpiod_table);
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 
 	mx21ads_cs8900_resources[1].start =

arch/arm/mach-imx/mach-mx27ads.c

@@ -16,6 +16,7 @@
 #include <linux/gpio/driver.h>
 /* Needed for gpio_to_irq() */
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/map.h>
@@ -230,10 +231,17 @@ static struct regulator_init_data mx27ads_lcd_regulator_init_data = {
 static struct fixed_voltage_config mx27ads_lcd_regulator_pdata = {
 	.supply_name	= "LCD",
 	.microvolts	= 3300000,
-	.gpio		= MX27ADS_LCD_GPIO,
 	.init_data	= &mx27ads_lcd_regulator_init_data,
 };
 
+static struct gpiod_lookup_table mx27ads_lcd_regulator_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.0", /* Let's hope ID 0 is what we get */
+	.table = {
+		GPIO_LOOKUP("LCD", 0, NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init mx27ads_regulator_init(void)
 {
 	struct gpio_chip *vchip;
@@ -247,6 +255,8 @@ static void __init mx27ads_regulator_init(void)
 	vchip->set		= vgpio_set;
 	gpiochip_add_data(vchip, NULL);
 
+	gpiod_add_lookup_table(&mx27ads_lcd_regulator_gpiod_table);
+
 	platform_device_register_data(NULL, "reg-fixed-voltage",
 				      PLATFORM_DEVID_AUTO,
 				      &mx27ads_lcd_regulator_pdata,

arch/arm/mach-mmp/brownstone.c

@@ -15,6 +15,7 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/gpio-pxa.h>
+#include <linux/gpio/machine.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/max8649.h>
 #include <linux/regulator/fixed.h>
@@ -148,7 +149,6 @@ static struct regulator_init_data brownstone_v_5vp_data = {
 static struct fixed_voltage_config brownstone_v_5vp = {
 	.supply_name		= "v_5vp",
 	.microvolts		= 5000000,
-	.gpio			= GPIO_5V_ENABLE,
 	.enable_high		= 1,
 	.enabled_at_boot	= 1,
 	.init_data		= &brownstone_v_5vp_data,
@@ -162,6 +162,15 @@ static struct platform_device brownstone_v_5vp_device = {
 	},
 };
 
+static struct gpiod_lookup_table brownstone_v_5vp_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.1", /* .id set to 1 above */
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", GPIO_5V_ENABLE,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct max8925_platform_data brownstone_max8925_info = {
 	.irq_base		= MMP_NR_IRQS,
 };
@@ -217,6 +226,7 @@ static void __init brownstone_init(void)
 	mmp2_add_isram(&mmp2_isram_platdata);
 
 	/* enable 5v regulator */
+	gpiod_add_lookup_table(&brownstone_v_5vp_gpiod_table);
 	platform_device_register(&brownstone_v_5vp_device);
 }
 

arch/arm/mach-omap1/board-ams-delta.c

@@ -300,7 +300,6 @@ static struct regulator_init_data modem_nreset_data = {
 static struct fixed_voltage_config modem_nreset_config = {
 	.supply_name		= "modem_nreset",
 	.microvolts		= 3300000,
-	.gpio			= AMS_DELTA_GPIO_PIN_MODEM_NRESET,
 	.startup_delay		= 25000,
 	.enable_high		= 1,
 	.enabled_at_boot	= 1,
@@ -315,6 +314,15 @@ static struct platform_device modem_nreset_device = {
 	},
 };
 
+static struct gpiod_lookup_table ams_delta_nreset_gpiod_table = {
+	.dev_id = "reg-fixed-voltage",
+	.table = {
+		GPIO_LOOKUP(LATCH2_LABEL, LATCH2_PIN_MODEM_NRESET,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 struct modem_private_data {
 	struct regulator *regulator;
 };
@@ -568,7 +576,6 @@ static struct regulator_init_data keybrd_pwr_initdata = {
 static struct fixed_voltage_config keybrd_pwr_config = {
 	.supply_name		= "keybrd_pwr",
 	.microvolts		= 5000000,
-	.gpio			= AMS_DELTA_GPIO_PIN_KEYBRD_PWR,
 	.enable_high		= 1,
 	.init_data		= &keybrd_pwr_initdata,
 };
@@ -602,6 +609,7 @@ static struct platform_device *ams_delta_devices[] __initdata = {
 };
 
 static struct gpiod_lookup_table *ams_delta_gpio_tables[] __initdata = {
+	&ams_delta_nreset_gpiod_table,
 	&ams_delta_audio_gpio_table,
 	&keybrd_pwr_gpio_table,
 	&ams_delta_lcd_gpio_table,

arch/arm/mach-omap2/pdata-quirks.c

@@ -10,6 +10,7 @@
 #include <linux/clk.h>
 #include <linux/davinci_emac.h>
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/of_platform.h>
@@ -328,7 +329,6 @@ static struct regulator_init_data pandora_vmmc3 = {
 static struct fixed_voltage_config pandora_vwlan = {
 	.supply_name		= "vwlan",
 	.microvolts		= 1800000, /* 1.8V */
-	.gpio			= PANDORA_WIFI_NRESET_GPIO,
 	.startup_delay		= 50000, /* 50ms */
 	.enable_high		= 1,
 	.init_data		= &pandora_vmmc3,
@@ -342,6 +342,19 @@ static struct platform_device pandora_vwlan_device = {
 	},
 };
 
+static struct gpiod_lookup_table pandora_vwlan_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.1",
+	.table = {
+		/*
+		 * As this is a low GPIO number it should be at the first
+		 * GPIO bank.
+		 */
+		GPIO_LOOKUP("gpio-0-31", PANDORA_WIFI_NRESET_GPIO,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void pandora_wl1251_init_card(struct mmc_card *card)
 {
 	/*
@@ -403,6 +416,7 @@ static void __init pandora_wl1251_init(void)
 static void __init omap3_pandora_legacy_init(void)
 {
 	platform_device_register(&pandora_backlight);
+	gpiod_add_lookup_table(&pandora_vwlan_gpiod_table);
 	platform_device_register(&pandora_vwlan_device);
 	omap_hsmmc_init(pandora_mmc3);
 	omap_hsmmc_late_init(pandora_mmc3);

arch/arm/mach-pxa/em-x270.c

@@ -986,7 +986,6 @@ static struct fixed_voltage_config camera_dummy_config = {
 	.supply_name		= "camera_vdd",
 	.input_supply		= "vcc cam",
 	.microvolts		= 2800000,
-	.gpio			= -1,
 	.enable_high		= 0,
 	.init_data		= &camera_dummy_initdata,
 };

arch/arm/mach-pxa/ezx.c

@@ -21,6 +21,7 @@
 #include <linux/regulator/fixed.h>
 #include <linux/input.h>
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/gpio_keys.h>
 #include <linux/leds-lp3944.h>
 #include <linux/platform_data/i2c-pxa.h>
@@ -698,31 +699,39 @@ static struct pxa27x_keypad_platform_data e2_keypad_platform_data = {
 
 #if defined(CONFIG_MACH_EZX_A780) || defined(CONFIG_MACH_EZX_A910)
 /* camera */
-static struct regulator_consumer_supply camera_dummy_supplies[] = {
+static struct regulator_consumer_supply camera_regulator_supplies[] = {
 	REGULATOR_SUPPLY("vdd", "0-005d"),
 };
 
-static struct regulator_init_data camera_dummy_initdata = {
-	.consumer_supplies = camera_dummy_supplies,
-	.num_consumer_supplies = ARRAY_SIZE(camera_dummy_supplies),
+static struct regulator_init_data camera_regulator_initdata = {
+	.consumer_supplies = camera_regulator_supplies,
+	.num_consumer_supplies = ARRAY_SIZE(camera_regulator_supplies),
 	.constraints = {
 		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
 	},
 };
 
-static struct fixed_voltage_config camera_dummy_config = {
+static struct fixed_voltage_config camera_regulator_config = {
 	.supply_name		= "camera_vdd",
 	.microvolts		= 2800000,
-	.gpio			= GPIO50_nCAM_EN,
 	.enable_high		= 0,
-	.init_data		= &camera_dummy_initdata,
+	.init_data		= &camera_regulator_initdata,
 };
 
-static struct platform_device camera_supply_dummy_device = {
+static struct platform_device camera_supply_regulator_device = {
 	.name	= "reg-fixed-voltage",
 	.id	= 1,
 	.dev	= {
-		.platform_data = &camera_dummy_config,
+		.platform_data = &camera_regulator_config,
+	},
+};
+
+static struct gpiod_lookup_table camera_supply_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.1",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", GPIO50_nCAM_EN,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
 	},
 };
 #endif
@@ -800,7 +809,7 @@ static struct i2c_board_info a780_i2c_board_info[] = {
 
 static struct platform_device *a780_devices[] __initdata = {
 	&a780_gpio_keys,
-	&camera_supply_dummy_device,
+	&camera_supply_regulator_device,
 };
 
 static void __init a780_init(void)
@@ -823,6 +832,7 @@ static void __init a780_init(void)
 	if (a780_camera_init() == 0)
 		pxa_set_camera_info(&a780_pxacamera_platform_data);
 
+	gpiod_add_lookup_table(&camera_supply_gpiod_table);
 	pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
 	platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
 	platform_add_devices(ARRAY_AND_SIZE(a780_devices));
@@ -1098,7 +1108,7 @@ static struct i2c_board_info __initdata a910_i2c_board_info[] = {
 
 static struct platform_device *a910_devices[] __initdata = {
 	&a910_gpio_keys,
-	&camera_supply_dummy_device,
+	&camera_supply_regulator_device,
 };
 
 static void __init a910_init(void)
@@ -1121,6 +1131,7 @@ static void __init a910_init(void)
 	if (a910_camera_init() == 0)
 		pxa_set_camera_info(&a910_pxacamera_platform_data);
 
+	gpiod_add_lookup_table(&camera_supply_gpiod_table);
 	pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
 	platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
 	platform_add_devices(ARRAY_AND_SIZE(a910_devices));

arch/arm/mach-pxa/magician.c

@@ -18,6 +18,7 @@
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
 #include <linux/mfd/htc-pasic3.h>
@@ -696,7 +697,6 @@ static struct regulator_init_data vads7846_regulator = {
 static struct fixed_voltage_config vads7846 = {
 	.supply_name	= "vads7846",
 	.microvolts	= 3300000, /* probably */
-	.gpio		= -EINVAL,
 	.startup_delay	= 0,
 	.init_data	= &vads7846_regulator,
 };

arch/arm/mach-pxa/raumfeld.c

@@ -886,7 +886,6 @@ static struct regulator_init_data audio_va_initdata = {
 static struct fixed_voltage_config audio_va_config = {
 	.supply_name		= "audio_va",
 	.microvolts		= 5000000,
-	.gpio			= GPIO_AUDIO_VA_ENABLE,
 	.enable_high		= 1,
 	.enabled_at_boot	= 0,
 	.init_data		= &audio_va_initdata,
@@ -900,6 +899,15 @@ static struct platform_device audio_va_device = {
 	},
 };
 
+static struct gpiod_lookup_table audio_va_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.0",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", GPIO_AUDIO_VA_ENABLE,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /* Dummy supplies for Codec's VD/VLC */
 
 static struct regulator_consumer_supply audio_dummy_supplies[] = {
@@ -918,7 +926,6 @@ static struct regulator_init_data audio_dummy_initdata = {
 static struct fixed_voltage_config audio_dummy_config = {
 	.supply_name		= "audio_vd",
 	.microvolts		= 3300000,
-	.gpio			= -1,
 	.init_data		= &audio_dummy_initdata,
 };
 
@@ -1033,6 +1040,7 @@ static void __init raumfeld_audio_init(void)
 	else
 		gpio_direction_output(GPIO_MCLK_RESET, 1);
 
+	gpiod_add_lookup_table(&audio_va_gpiod_table);
 	platform_add_devices(ARRAY_AND_SIZE(audio_regulator_devices));
 }
 

arch/arm/mach-pxa/zeus.c

@@ -17,6 +17,7 @@
 #include <linux/irq.h>
 #include <linux/pm.h>
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/serial_8250.h>
 #include <linux/dm9000.h>
 #include <linux/mmc/host.h>
@@ -410,7 +411,6 @@ static struct regulator_init_data can_regulator_init_data = {
 static struct fixed_voltage_config can_regulator_pdata = {
 	.supply_name	= "CAN_SHDN",
 	.microvolts	= 3300000,
-	.gpio		= ZEUS_CAN_SHDN_GPIO,
 	.init_data	= &can_regulator_init_data,
 };
 
@@ -422,6 +422,15 @@ static struct platform_device can_regulator_device = {
 	},
 };
 
+static struct gpiod_lookup_table can_regulator_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.0",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", ZEUS_CAN_SHDN_GPIO,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct mcp251x_platform_data zeus_mcp2515_pdata = {
 	.oscillator_frequency	= 16*1000*1000,
 };
@@ -538,7 +547,6 @@ static struct regulator_init_data zeus_ohci_regulator_data = {
 static struct fixed_voltage_config zeus_ohci_regulator_config = {
 	.supply_name		= "vbus2",
 	.microvolts		= 5000000, /* 5.0V */
-	.gpio			= ZEUS_USB2_PWREN_GPIO,
 	.enable_high		= 1,
 	.startup_delay		= 0,
 	.init_data		= &zeus_ohci_regulator_data,
@@ -552,6 +560,15 @@ static struct platform_device zeus_ohci_regulator_device = {
 	},
 };
 
+static struct gpiod_lookup_table zeus_ohci_regulator_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.0",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", ZEUS_USB2_PWREN_GPIO,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct pxaohci_platform_data zeus_ohci_platform_data = {
 	.port_mode	= PMM_NPS_MODE,
 	/* Clear Power Control Polarity Low and set Power Sense
@@ -855,6 +872,8 @@ static void __init zeus_init(void)
 
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(zeus_pin_config));
 
+	gpiod_add_lookup_table(&can_regulator_gpiod_table);
+	gpiod_add_lookup_table(&zeus_ohci_regulator_gpiod_table);
 	platform_add_devices(zeus_devices, ARRAY_SIZE(zeus_devices));
 
 	zeus_register_ohci();

arch/arm/mach-s3c64xx/mach-crag6410.c

@@ -352,7 +352,6 @@ static struct fixed_voltage_config wallvdd_pdata = {
 	.supply_name = "WALLVDD",
 	.microvolts = 5000000,
 	.init_data = &wallvdd_data,
-	.gpio = -EINVAL,
 };
 
 static struct platform_device wallvdd_device = {

arch/arm/mach-s3c64xx/mach-smdk6410.c

@@ -222,7 +222,6 @@ static struct fixed_voltage_config smdk6410_b_pwr_5v_pdata = {
 	.supply_name = "B_PWR_5V",
 	.microvolts = 5000000,
 	.init_data = &smdk6410_b_pwr_5v_data,
-	.gpio = -EINVAL,
 };
 
 static struct platform_device smdk6410_b_pwr_5v = {

arch/arm/mach-sa1100/assabet.c

@@ -101,7 +101,7 @@ static int __init assabet_init_gpio(void __iomem *reg, u32 def_val)
 
 	assabet_bcr_gc = gc;
 
-	return gc->base;
+	return 0;
 }
 
 /*
@@ -471,6 +471,14 @@ static struct fixed_voltage_config assabet_cf_vcc_pdata __initdata = {
 	.enable_high = 1,
 };
 
+static struct gpiod_lookup_table assabet_cf_vcc_gpio_table = {
+	.dev_id = "reg-fixed-voltage.0",
+	.table = {
+		GPIO_LOOKUP("assabet", 0, NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init assabet_init(void)
 {
 	/*
@@ -517,9 +525,11 @@ static void __init assabet_init(void)
 			neponset_resources, ARRAY_SIZE(neponset_resources));
 #endif
 	} else {
+		gpiod_add_lookup_table(&assabet_cf_vcc_gpio_table);
 		sa11x0_register_fixed_regulator(0, &assabet_cf_vcc_pdata,
-					 assabet_cf_vcc_consumers,
-					 ARRAY_SIZE(assabet_cf_vcc_consumers));
+					assabet_cf_vcc_consumers,
+					ARRAY_SIZE(assabet_cf_vcc_consumers),
+					true);
 
 	}
 
@@ -802,7 +812,6 @@ fs_initcall(assabet_leds_init);
 
 void __init assabet_init_irq(void)
 {
-	unsigned int assabet_gpio_base;
 	u32 def_val;
 
 	sa1100_init_irq();
@@ -817,9 +826,7 @@ void __init assabet_init_irq(void)
 	 *
 	 * This must precede any driver calls to BCR_set() or BCR_clear().
 	 */
-	assabet_gpio_base = assabet_init_gpio((void *)&ASSABET_BCR, def_val);
-
-	assabet_cf_vcc_pdata.gpio = assabet_gpio_base + 0;
+	assabet_init_gpio((void *)&ASSABET_BCR, def_val);
 }
 
 MACHINE_START(ASSABET, "Intel-Assabet")

arch/arm/mach-sa1100/generic.c

@@ -348,7 +348,8 @@ void __init sa11x0_init_late(void)
 
 int __init sa11x0_register_fixed_regulator(int n,
 	struct fixed_voltage_config *cfg,
-	struct regulator_consumer_supply *supplies, unsigned num_supplies)
+	struct regulator_consumer_supply *supplies, unsigned num_supplies,
+	bool uses_gpio)
 {
 	struct regulator_init_data *id;
 
@@ -356,7 +357,7 @@ int __init sa11x0_register_fixed_regulator(int n,
 	if (!cfg->init_data)
 		return -ENOMEM;
 
-	if (cfg->gpio < 0)
+	if (!uses_gpio)
 		id->constraints.always_on = 1;
 	id->constraints.name = cfg->supply_name;
 	id->constraints.min_uV = cfg->microvolts;

arch/arm/mach-sa1100/generic.h

@@ -54,4 +54,5 @@ void sa11x0_register_pcmcia(int socket, struct gpiod_lookup_table *);
 struct fixed_voltage_config;
 struct regulator_consumer_supply;
 int sa11x0_register_fixed_regulator(int n, struct fixed_voltage_config *cfg,
-	struct regulator_consumer_supply *supplies, unsigned num_supplies);
+	struct regulator_consumer_supply *supplies, unsigned num_supplies,
+	bool uses_gpio);

arch/arm/mach-sa1100/shannon.c

@@ -102,14 +102,14 @@ static struct fixed_voltage_config shannon_cf_vcc_pdata __initdata = {
 	.supply_name = "cf-power",
 	.microvolts = 3300000,
 	.enabled_at_boot = 1,
-	.gpio = -EINVAL,
 };
 
 static void __init shannon_init(void)
 {
 	sa11x0_register_fixed_regulator(0, &shannon_cf_vcc_pdata,
 					shannon_cf_vcc_consumers,
-					ARRAY_SIZE(shannon_cf_vcc_consumers));
+					ARRAY_SIZE(shannon_cf_vcc_consumers),
+					false);
 	sa11x0_register_pcmcia(0, &shannon_pcmcia0_gpio_table);
 	sa11x0_register_pcmcia(1, &shannon_pcmcia1_gpio_table);
 	sa11x0_ppc_configure_mcp();

arch/sh/boards/mach-ecovec24/setup.c

@@ -633,7 +633,6 @@ static struct regulator_init_data cn12_power_init_data = {
 static struct fixed_voltage_config cn12_power_info = {
 	.supply_name = "CN12 SD/MMC Vdd",
 	.microvolts = 3300000,
-	.gpio = GPIO_PTB7,
 	.enable_high = 1,
 	.init_data = &cn12_power_init_data,
 };
@@ -646,6 +645,16 @@ static struct platform_device cn12_power = {
 	},
 };
 
+static struct gpiod_lookup_table cn12_power_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.0",
+	.table = {
+		/* Offset 7 on port B */
+		GPIO_LOOKUP("sh7724_pfc", GPIO_PTB7,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 #if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
 /* SDHI0 */
 static struct regulator_consumer_supply sdhi0_power_consumers[] =
@@ -665,7 +674,6 @@ static struct regulator_init_data sdhi0_power_init_data = {
 static struct fixed_voltage_config sdhi0_power_info = {
 	.supply_name = "CN11 SD/MMC Vdd",
 	.microvolts = 3300000,
-	.gpio = GPIO_PTB6,
 	.enable_high = 1,
 	.init_data = &sdhi0_power_init_data,
 };
@@ -678,6 +686,16 @@ static struct platform_device sdhi0_power = {
 	},
 };
 
+static struct gpiod_lookup_table sdhi0_power_gpiod_table = {
+	.dev_id = "reg-fixed-voltage.1",
+	.table = {
+		/* Offset 6 on port B */
+		GPIO_LOOKUP("sh7724_pfc", GPIO_PTB6,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct tmio_mmc_data sdhi0_info = {
 	.chan_priv_tx	= (void *)SHDMA_SLAVE_SDHI0_TX,
 	.chan_priv_rx	= (void *)SHDMA_SLAVE_SDHI0_RX,
@@ -1413,6 +1431,11 @@ static int __init arch_setup(void)
 				    DMA_MEMORY_EXCLUSIVE);
 	platform_device_add(ecovec_ceu_devices[1]);
 
+	gpiod_add_lookup_table(&cn12_power_gpiod_table);
+#if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
+	gpiod_add_lookup_table(&sdhi0_power_gpiod_table);
+#endif
+
 	return platform_add_devices(ecovec_devices,
 				    ARRAY_SIZE(ecovec_devices));
 }

arch/x86/platform/intel-mid/device_libs/platform_bcm43xx.c

@@ -10,7 +10,7 @@
  * of the License.
  */
 
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/fixed.h>
@@ -43,7 +43,6 @@ static struct fixed_voltage_config bcm43xx_vmmc = {
 	 * real voltage and signaling are still 1.8V.
 	 */
 	.microvolts		= 2000000,		/* 1.8V */
-	.gpio			= -EINVAL,
 	.startup_delay		= 250 * 1000,		/* 250ms */
 	.enable_high		= 1,			/* active high */
 	.enabled_at_boot	= 0,			/* disabled at boot */
@@ -58,11 +57,23 @@ static struct platform_device bcm43xx_vmmc_regulator = {
 	},
 };
 
+static struct gpiod_lookup_table bcm43xx_vmmc_gpio_table = {
+	.dev_id	= "reg-fixed-voltage.0",
+	.table	= {
+		GPIO_LOOKUP("0000:00:0c.0", -1, NULL, GPIO_ACTIVE_LOW),
+		{}
+	},
+};
+
 static int __init bcm43xx_regulator_register(void)
 {
+	struct gpiod_lookup_table *table = &bcm43xx_vmmc_gpio_table;
+	struct gpiod_lookup *lookup = table->table;
 	int ret;
 
-	bcm43xx_vmmc.gpio = get_gpio_by_name(WLAN_SFI_GPIO_ENABLE_NAME);
+	lookup[0].chip_hwnum = get_gpio_by_name(WLAN_SFI_GPIO_ENABLE_NAME);
+	gpiod_add_lookup_table(table);
+
 	ret = platform_device_register(&bcm43xx_vmmc_regulator);
 	if (ret) {
 		pr_err("%s: vmmc regulator register failed\n", __func__);

drivers/gpio/gpiolib.c

@@ -3909,8 +3909,23 @@ struct gpio_desc *__must_check gpiod_get_index(struct device *dev,
 	 * the device name as label
 	 */
 	status = gpiod_request(desc, con_id ? con_id : devname);
-	if (status < 0)
-		return ERR_PTR(status);
+	if (status < 0) {
+		if (status == -EBUSY && flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
+			/*
+			 * This happens when there are several consumers for
+			 * the same GPIO line: we just return here without
+			 * further initialization. It is a bit if a hack.
+			 * This is necessary to support fixed regulators.
+			 *
+			 * FIXME: Make this more sane and safe.
+			 */
+			dev_info(dev, "nonexclusive access to GPIO for %s\n",
+				 con_id ? con_id : devname);
+			return desc;
+		} else {
+			return ERR_PTR(status);
+		}
+	}
 
 	status = gpiod_configure_flags(desc, con_id, lookupflags, flags);
 	if (status < 0) {

drivers/mfd/rohm-bd718x7.c

@@ -2,26 +2,21 @@
 //
 // Copyright (C) 2018 ROHM Semiconductors
 //
-// ROHM BD71837MWV PMIC driver
+// ROHM BD71837MWV and BD71847MWV PMIC driver
 //
-// Datasheet available from
+// Datasheet for BD71837MWV available from
 // https://www.rohm.com/datasheet/BD71837MWV/bd71837mwv-e
 
+#include <linux/gpio_keys.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/mfd/rohm-bd718x7.h>
 #include <linux/mfd/core.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/regmap.h>
-
-/*
- * gpio_keys.h requires definiton of bool. It is brought in
- * by above includes. Keep this as last until gpio_keys.h gets fixed.
- */
-#include <linux/gpio_keys.h>
-
-static const u8 supported_revisions[] = { 0xA2 /* BD71837 */ };
+#include <linux/types.h>
 
 static struct gpio_keys_button button = {
 	.code = KEY_POWER,
@@ -35,42 +30,42 @@ static struct gpio_keys_platform_data bd718xx_powerkey_data = {
 	.name = "bd718xx-pwrkey",
 };
 
-static struct mfd_cell bd71837_mfd_cells[] = {
+static struct mfd_cell bd718xx_mfd_cells[] = {
 	{
 		.name = "gpio-keys",
 		.platform_data = &bd718xx_powerkey_data,
 		.pdata_size = sizeof(bd718xx_powerkey_data),
 	},
-	{ .name = "bd71837-clk", },
-	{ .name = "bd71837-pmic", },
+	{ .name = "bd718xx-clk", },
+	{ .name = "bd718xx-pmic", },
 };
 
-static const struct regmap_irq bd71837_irqs[] = {
-	REGMAP_IRQ_REG(BD71837_INT_SWRST, 0, BD71837_INT_SWRST_MASK),
-	REGMAP_IRQ_REG(BD71837_INT_PWRBTN_S, 0, BD71837_INT_PWRBTN_S_MASK),
-	REGMAP_IRQ_REG(BD71837_INT_PWRBTN_L, 0, BD71837_INT_PWRBTN_L_MASK),
-	REGMAP_IRQ_REG(BD71837_INT_PWRBTN, 0, BD71837_INT_PWRBTN_MASK),
-	REGMAP_IRQ_REG(BD71837_INT_WDOG, 0, BD71837_INT_WDOG_MASK),
-	REGMAP_IRQ_REG(BD71837_INT_ON_REQ, 0, BD71837_INT_ON_REQ_MASK),
-	REGMAP_IRQ_REG(BD71837_INT_STBY_REQ, 0, BD71837_INT_STBY_REQ_MASK),
+static const struct regmap_irq bd718xx_irqs[] = {
+	REGMAP_IRQ_REG(BD718XX_INT_SWRST, 0, BD718XX_INT_SWRST_MASK),
+	REGMAP_IRQ_REG(BD718XX_INT_PWRBTN_S, 0, BD718XX_INT_PWRBTN_S_MASK),
+	REGMAP_IRQ_REG(BD718XX_INT_PWRBTN_L, 0, BD718XX_INT_PWRBTN_L_MASK),
+	REGMAP_IRQ_REG(BD718XX_INT_PWRBTN, 0, BD718XX_INT_PWRBTN_MASK),
+	REGMAP_IRQ_REG(BD718XX_INT_WDOG, 0, BD718XX_INT_WDOG_MASK),
+	REGMAP_IRQ_REG(BD718XX_INT_ON_REQ, 0, BD718XX_INT_ON_REQ_MASK),
+	REGMAP_IRQ_REG(BD718XX_INT_STBY_REQ, 0, BD718XX_INT_STBY_REQ_MASK),
 };
 
-static struct regmap_irq_chip bd71837_irq_chip = {
-	.name = "bd71837-irq",
-	.irqs = bd71837_irqs,
-	.num_irqs = ARRAY_SIZE(bd71837_irqs),
+static struct regmap_irq_chip bd718xx_irq_chip = {
+	.name = "bd718xx-irq",
+	.irqs = bd718xx_irqs,
+	.num_irqs = ARRAY_SIZE(bd718xx_irqs),
 	.num_regs = 1,
 	.irq_reg_stride = 1,
-	.status_base = BD71837_REG_IRQ,
-	.mask_base = BD71837_REG_MIRQ,
-	.ack_base = BD71837_REG_IRQ,
+	.status_base = BD718XX_REG_IRQ,
+	.mask_base = BD718XX_REG_MIRQ,
+	.ack_base = BD718XX_REG_IRQ,
 	.init_ack_masked = true,
 	.mask_invert = false,
 };
 
 static const struct regmap_range pmic_status_range = {
-	.range_min = BD71837_REG_IRQ,
-	.range_max = BD71837_REG_POW_STATE,
+	.range_min = BD718XX_REG_IRQ,
+	.range_max = BD718XX_REG_POW_STATE,
 };
 
 static const struct regmap_access_table volatile_regs = {
@@ -78,67 +73,53 @@ static const struct regmap_access_table volatile_regs = {
 	.n_yes_ranges = 1,
 };
 
-static const struct regmap_config bd71837_regmap_config = {
+static const struct regmap_config bd718xx_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
 	.volatile_table = &volatile_regs,
-	.max_register = BD71837_MAX_REGISTER - 1,
+	.max_register = BD718XX_MAX_REGISTER - 1,
 	.cache_type = REGCACHE_RBTREE,
 };
 
-static int bd71837_i2c_probe(struct i2c_client *i2c,
+static int bd718xx_i2c_probe(struct i2c_client *i2c,
 			    const struct i2c_device_id *id)
 {
-	struct bd71837 *bd71837;
-	int ret, i;
-	unsigned int val;
-
-	bd71837 = devm_kzalloc(&i2c->dev, sizeof(struct bd71837), GFP_KERNEL);
+	struct bd718xx *bd718xx;
+	int ret;
 
-	if (!bd71837)
-		return -ENOMEM;
-
-	bd71837->chip_irq = i2c->irq;
-
-	if (!bd71837->chip_irq) {
+	if (!i2c->irq) {
 		dev_err(&i2c->dev, "No IRQ configured\n");
 		return -EINVAL;
 	}
 
-	bd71837->dev = &i2c->dev;
-	dev_set_drvdata(&i2c->dev, bd71837);
+	bd718xx = devm_kzalloc(&i2c->dev, sizeof(struct bd718xx), GFP_KERNEL);
 
-	bd71837->regmap = devm_regmap_init_i2c(i2c, &bd71837_regmap_config);
-	if (IS_ERR(bd71837->regmap)) {
-		dev_err(&i2c->dev, "regmap initialization failed\n");
-		return PTR_ERR(bd71837->regmap);
-	}
+	if (!bd718xx)
+		return -ENOMEM;
 
-	ret = regmap_read(bd71837->regmap, BD71837_REG_REV, &val);
-	if (ret) {
-		dev_err(&i2c->dev, "Read BD71837_REG_DEVICE failed\n");
-		return ret;
-	}
-	for (i = 0; i < ARRAY_SIZE(supported_revisions); i++)
-		if (supported_revisions[i] == val)
-			break;
+	bd718xx->chip_irq = i2c->irq;
+	bd718xx->chip_type = (unsigned int)
+				of_device_get_match_data(&i2c->dev);
+	bd718xx->dev = &i2c->dev;
+	dev_set_drvdata(&i2c->dev, bd718xx);
 
-	if (i == ARRAY_SIZE(supported_revisions)) {
-		dev_err(&i2c->dev, "Unsupported chip revision\n");
-		return -ENODEV;
+	bd718xx->regmap = devm_regmap_init_i2c(i2c, &bd718xx_regmap_config);
+	if (IS_ERR(bd718xx->regmap)) {
+		dev_err(&i2c->dev, "regmap initialization failed\n");
+		return PTR_ERR(bd718xx->regmap);
 	}
 
-	ret = devm_regmap_add_irq_chip(&i2c->dev, bd71837->regmap,
-				       bd71837->chip_irq, IRQF_ONESHOT, 0,
-				       &bd71837_irq_chip, &bd71837->irq_data);
+	ret = devm_regmap_add_irq_chip(&i2c->dev, bd718xx->regmap,
+				       bd718xx->chip_irq, IRQF_ONESHOT, 0,
+				       &bd718xx_irq_chip, &bd718xx->irq_data);
 	if (ret) {
 		dev_err(&i2c->dev, "Failed to add irq_chip\n");
 		return ret;
 	}
 
 	/* Configure short press to 10 milliseconds */
-	ret = regmap_update_bits(bd71837->regmap,
-				 BD71837_REG_PWRONCONFIG0,
+	ret = regmap_update_bits(bd718xx->regmap,
+				 BD718XX_REG_PWRONCONFIG0,
 				 BD718XX_PWRBTN_PRESS_DURATION_MASK,
 				 BD718XX_PWRBTN_SHORT_PRESS_10MS);
 	if (ret) {
@@ -148,8 +129,8 @@ static int bd71837_i2c_probe(struct i2c_client *i2c,
 	}
 
 	/* Configure long press to 10 seconds */
-	ret = regmap_update_bits(bd71837->regmap,
-				 BD71837_REG_PWRONCONFIG1,
+	ret = regmap_update_bits(bd718xx->regmap,
+				 BD718XX_REG_PWRONCONFIG1,
 				 BD718XX_PWRBTN_PRESS_DURATION_MASK,
 				 BD718XX_PWRBTN_LONG_PRESS_10S);
 
@@ -159,7 +140,7 @@ static int bd71837_i2c_probe(struct i2c_client *i2c,
 		return ret;
 	}
 
-	ret = regmap_irq_get_virq(bd71837->irq_data, BD71837_INT_PWRBTN_S);
+	ret = regmap_irq_get_virq(bd718xx->irq_data, BD718XX_INT_PWRBTN_S);
 
 	if (ret < 0) {
 		dev_err(&i2c->dev, "Failed to get the IRQ\n");
@@ -168,44 +149,51 @@ static int bd71837_i2c_probe(struct i2c_client *i2c,
 
 	button.irq = ret;
 
-	ret = devm_mfd_add_devices(bd71837->dev, PLATFORM_DEVID_AUTO,
-				   bd71837_mfd_cells,
-				   ARRAY_SIZE(bd71837_mfd_cells), NULL, 0,
-				   regmap_irq_get_domain(bd71837->irq_data));
+	ret = devm_mfd_add_devices(bd718xx->dev, PLATFORM_DEVID_AUTO,
+				   bd718xx_mfd_cells,
+				   ARRAY_SIZE(bd718xx_mfd_cells), NULL, 0,
+				   regmap_irq_get_domain(bd718xx->irq_data));
 	if (ret)
 		dev_err(&i2c->dev, "Failed to create subdevices\n");
 
 	return ret;
 }
 
-static const struct of_device_id bd71837_of_match[] = {
-	{ .compatible = "rohm,bd71837", },
+static const struct of_device_id bd718xx_of_match[] = {
+	{
+		.compatible = "rohm,bd71837",
+		.data = (void *)BD718XX_TYPE_BD71837,
+	},
+	{
+		.compatible = "rohm,bd71847",
+		.data = (void *)BD718XX_TYPE_BD71847,
+	},
 	{ }
 };
-MODULE_DEVICE_TABLE(of, bd71837_of_match);
+MODULE_DEVICE_TABLE(of, bd718xx_of_match);
 
-static struct i2c_driver bd71837_i2c_driver = {
+static struct i2c_driver bd718xx_i2c_driver = {
 	.driver = {
 		.name = "rohm-bd718x7",
-		.of_match_table = bd71837_of_match,
+		.of_match_table = bd718xx_of_match,
 	},
-	.probe = bd71837_i2c_probe,
+	.probe = bd718xx_i2c_probe,
 };
 
-static int __init bd71837_i2c_init(void)
+static int __init bd718xx_i2c_init(void)
 {
-	return i2c_add_driver(&bd71837_i2c_driver);
+	return i2c_add_driver(&bd718xx_i2c_driver);
 }
 
 /* Initialise early so consumer devices can complete system boot */
-subsys_initcall(bd71837_i2c_init);
+subsys_initcall(bd718xx_i2c_init);
 
-static void __exit bd71837_i2c_exit(void)
+static void __exit bd718xx_i2c_exit(void)
 {
-	i2c_del_driver(&bd71837_i2c_driver);
+	i2c_del_driver(&bd718xx_i2c_driver);
 }
-module_exit(bd71837_i2c_exit);
+module_exit(bd718xx_i2c_exit);
 
 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
-MODULE_DESCRIPTION("ROHM BD71837 Power Management IC driver");
+MODULE_DESCRIPTION("ROHM BD71837/BD71847 Power Management IC driver");
 MODULE_LICENSE("GPL");

drivers/regulator/Kconfig

@@ -189,7 +189,7 @@ config REGULATOR_BD718XX
 	  and LDO regulators.
 
 	  This driver can also be built as a module. If so, the module
-	  will be called bd71837-regulator.
+	  will be called bd718x7-regulator.
 
 config REGULATOR_BD9571MWV
 	tristate "ROHM BD9571MWV Regulators"
@@ -356,6 +356,13 @@ config REGULATOR_LM363X
 	  One boost output voltage is configurable and always on.
 	  Other LDOs are used for the display module.
 
+config REGULATOR_LOCHNAGAR
+	tristate "Cirrus Logic Lochnagar regulator driver"
+	depends on MFD_LOCHNAGAR
+	help
+	  This enables regulator support on the Cirrus Logic Lochnagar audio
+	  development board.
+
 config REGULATOR_LP3971
 	tristate "National Semiconductors LP3971 PMIC regulator driver"
 	depends on I2C
@@ -803,6 +810,18 @@ config REGULATOR_STM32_VREFBUF
 	  This driver can also be built as a module. If so, the module
 	  will be called stm32-vrefbuf.
 
+config REGULATOR_STPMIC1
+	tristate "STMicroelectronics STPMIC1 PMIC Regulators"
+	depends on MFD_STPMIC1
+	help
+	  This driver supports STMicroelectronics STPMIC1 PMIC voltage
+	  regulators and switches. The STPMIC1 regulators supply power to
+	  an application processor as well as to external system
+	  peripherals such as DDR, Flash memories and system devices.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called stpmic1_regulator.
+
 config REGULATOR_TI_ABB
 	tristate "TI Adaptive Body Bias on-chip LDO"
 	depends on ARCH_OMAP

drivers/regulator/Makefile

@@ -27,7 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
 obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
 obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
 obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
-obj-$(CONFIG_REGULATOR_BD718XX) += bd71837-regulator.o
+obj-$(CONFIG_REGULATOR_BD718XX) += bd718x7-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x.o
 obj-$(CONFIG_REGULATOR_DA9052)	+= da9052-regulator.o
@@ -46,6 +46,7 @@ obj-$(CONFIG_REGULATOR_HI655X) += hi655x-regulator.o
 obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o
 obj-$(CONFIG_REGULATOR_ISL9305) += isl9305.o
 obj-$(CONFIG_REGULATOR_LM363X) += lm363x-regulator.o
+obj-$(CONFIG_REGULATOR_LOCHNAGAR) += lochnagar-regulator.o
 obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
 obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o
 obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o
@@ -101,6 +102,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
 obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
 obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
 obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
+obj-$(CONFIG_REGULATOR_STPMIC1) += stpmic1_regulator.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
 obj-$(CONFIG_REGULATOR_SY8106A) += sy8106a-regulator.o
 obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o

drivers/regulator/arizona-ldo1.c

@@ -260,7 +260,7 @@ static int arizona_ldo1_common_init(struct platform_device *pdev,
 	 * so clean up would happen at the wrong time
 	 */
 	config.ena_gpiod = gpiod_get_optional(parent_dev, "wlf,ldoena",
-					      GPIOD_OUT_LOW);
+				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	if (IS_ERR(config.ena_gpiod))
 		return PTR_ERR(config.ena_gpiod);
 

drivers/regulator/axp20x-regulator.c

@@ -509,10 +509,10 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
 		/*
 		 * AXP803/AXP813 DCDC work frequency setting has the same
 		 * range and step as AXP22X, but at a different register.
-		 * Fall through to the check below.
 		 * (See include/linux/mfd/axp20x.h)
 		 */
 		reg = AXP803_DCDC_FREQ_CTRL;
+		/* Fall through to the check below.*/
 	case AXP806_ID:
 		/*
 		 * AXP806 also have DCDC work frequency setting register at a
@@ -520,6 +520,7 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
 		 */
 		if (axp20x->variant == AXP806_ID)
 			reg = AXP806_DCDC_FREQ_CTRL;
+		/* Fall through */
 	case AXP221_ID:
 	case AXP223_ID:
 	case AXP809_ID:

drivers/regulator/core.c

@@ -426,19 +426,24 @@ static ssize_t name_show(struct device *dev, struct device_attribute *attr,
 }
 static DEVICE_ATTR_RO(name);
 
-static ssize_t regulator_print_opmode(char *buf, int mode)
+static const char *regulator_opmode_to_str(int mode)
 {
 	switch (mode) {
 	case REGULATOR_MODE_FAST:
-		return sprintf(buf, "fast\n");
+		return "fast";
 	case REGULATOR_MODE_NORMAL:
-		return sprintf(buf, "normal\n");
+		return "normal";
 	case REGULATOR_MODE_IDLE:
-		return sprintf(buf, "idle\n");
+		return "idle";
 	case REGULATOR_MODE_STANDBY:
-		return sprintf(buf, "standby\n");
+		return "standby";
 	}
-	return sprintf(buf, "unknown\n");
+	return "unknown";
+}
+
+static ssize_t regulator_print_opmode(char *buf, int mode)
+{
+	return sprintf(buf, "%s\n", regulator_opmode_to_str(mode));
 }
 
 static ssize_t regulator_opmode_show(struct device *dev,
@@ -2783,6 +2788,11 @@ static int regulator_map_voltage(struct regulator_dev *rdev, int min_uV,
 	if (desc->ops->list_voltage == regulator_list_voltage_linear_range)
 		return regulator_map_voltage_linear_range(rdev, min_uV, max_uV);
 
+	if (desc->ops->list_voltage ==
+		regulator_list_voltage_pickable_linear_range)
+		return regulator_map_voltage_pickable_linear_range(rdev,
+							min_uV, max_uV);
+
 	return regulator_map_voltage_iterate(rdev, min_uV, max_uV);
 }
 
@@ -3470,21 +3480,23 @@ int regulator_set_current_limit(struct regulator *regulator,
 }
 EXPORT_SYMBOL_GPL(regulator_set_current_limit);
 
+static int _regulator_get_current_limit_unlocked(struct regulator_dev *rdev)
+{
+	/* sanity check */
+	if (!rdev->desc->ops->get_current_limit)
+		return -EINVAL;
+
+	return rdev->desc->ops->get_current_limit(rdev);
+}
+
 static int _regulator_get_current_limit(struct regulator_dev *rdev)
 {
 	int ret;
 
 	regulator_lock(rdev);
-
-	/* sanity check */
-	if (!rdev->desc->ops->get_current_limit) {
-		ret = -EINVAL;
-		goto out;
-	}
-
-	ret = rdev->desc->ops->get_current_limit(rdev);
-out:
+	ret = _regulator_get_current_limit_unlocked(rdev);
 	regulator_unlock(rdev);
+
 	return ret;
 }
 
@@ -3549,21 +3561,23 @@ int regulator_set_mode(struct regulator *regulator, unsigned int mode)
 }
 EXPORT_SYMBOL_GPL(regulator_set_mode);
 
+static unsigned int _regulator_get_mode_unlocked(struct regulator_dev *rdev)
+{
+	/* sanity check */
+	if (!rdev->desc->ops->get_mode)
+		return -EINVAL;
+
+	return rdev->desc->ops->get_mode(rdev);
+}
+
 static unsigned int _regulator_get_mode(struct regulator_dev *rdev)
 {
 	int ret;
 
 	regulator_lock(rdev);
-
-	/* sanity check */
-	if (!rdev->desc->ops->get_mode) {
-		ret = -EINVAL;
-		goto out;
-	}
-
-	ret = rdev->desc->ops->get_mode(rdev);
-out:
+	ret = _regulator_get_mode_unlocked(rdev);
 	regulator_unlock(rdev);
+
 	return ret;
 }
 
@@ -4455,41 +4469,33 @@ void regulator_unregister(struct regulator_dev *rdev)
 EXPORT_SYMBOL_GPL(regulator_unregister);
 
 #ifdef CONFIG_SUSPEND
-static int _regulator_suspend(struct device *dev, void *data)
-{
-	struct regulator_dev *rdev = dev_to_rdev(dev);
-	suspend_state_t *state = data;
-	int ret;
-
-	regulator_lock(rdev);
-	ret = suspend_set_state(rdev, *state);
-	regulator_unlock(rdev);
-
-	return ret;
-}
-
 /**
  * regulator_suspend - prepare regulators for system wide suspend
- * @state: system suspend state
+ * @dev: ``&struct device`` pointer that is passed to _regulator_suspend()
  *
  * Configure each regulator with it's suspend operating parameters for state.
  */
 static int regulator_suspend(struct device *dev)
 {
+	struct regulator_dev *rdev = dev_to_rdev(dev);
 	suspend_state_t state = pm_suspend_target_state;
+	int ret;
+
+	regulator_lock(rdev);
+	ret = suspend_set_state(rdev, state);
+	regulator_unlock(rdev);
 
-	return class_for_each_device(&regulator_class, NULL, &state,
-				     _regulator_suspend);
+	return ret;
 }
 
-static int _regulator_resume(struct device *dev, void *data)
+static int regulator_resume(struct device *dev)
 {
-	int ret = 0;
+	suspend_state_t state = pm_suspend_target_state;
 	struct regulator_dev *rdev = dev_to_rdev(dev);
-	suspend_state_t *state = data;
 	struct regulator_state *rstate;
+	int ret = 0;
 
-	rstate = regulator_get_suspend_state(rdev, *state);
+	rstate = regulator_get_suspend_state(rdev, state);
 	if (rstate == NULL)
 		return 0;
 
@@ -4504,15 +4510,6 @@ static int _regulator_resume(struct device *dev, void *data)
 
 	return ret;
 }
-
-static int regulator_resume(struct device *dev)
-{
-	suspend_state_t state = pm_suspend_target_state;
-
-	return class_for_each_device(&regulator_class, NULL, &state,
-				     _regulator_resume);
-}
-
 #else /* !CONFIG_SUSPEND */
 
 #define regulator_suspend	NULL
@@ -4670,17 +4667,23 @@ static void regulator_summary_show_subtree(struct seq_file *s,
 	struct regulation_constraints *c;
 	struct regulator *consumer;
 	struct summary_data summary_data;
+	unsigned int opmode;
 
 	if (!rdev)
 		return;
 
-	seq_printf(s, "%*s%-*s %3d %4d %6d ",
+	regulator_lock_nested(rdev, level);
+
+	opmode = _regulator_get_mode_unlocked(rdev);
+	seq_printf(s, "%*s%-*s %3d %4d %6d %7s ",
 		   level * 3 + 1, "",
 		   30 - level * 3, rdev_get_name(rdev),
-		   rdev->use_count, rdev->open_count, rdev->bypass_count);
+		   rdev->use_count, rdev->open_count, rdev->bypass_count,
+		   regulator_opmode_to_str(opmode));
 
 	seq_printf(s, "%5dmV ", _regulator_get_voltage(rdev) / 1000);
-	seq_printf(s, "%5dmA ", _regulator_get_current_limit(rdev) / 1000);
+	seq_printf(s, "%5dmA ",
+		   _regulator_get_current_limit_unlocked(rdev) / 1000);
 
 	c = rdev->constraints;
 	if (c) {
@@ -4709,7 +4712,8 @@ static void regulator_summary_show_subtree(struct seq_file *s,
 
 		switch (rdev->desc->type) {
 		case REGULATOR_VOLTAGE:
-			seq_printf(s, "%37dmV %5dmV",
+			seq_printf(s, "%37dmA %5dmV %5dmV",
+				   consumer->uA_load / 1000,
 				   consumer->voltage[PM_SUSPEND_ON].min_uV / 1000,
 				   consumer->voltage[PM_SUSPEND_ON].max_uV / 1000);
 			break;
@@ -4726,6 +4730,8 @@ static void regulator_summary_show_subtree(struct seq_file *s,
 
 	class_for_each_device(&regulator_class, NULL, &summary_data,
 			      regulator_summary_show_children);
+
+	regulator_unlock(rdev);
 }
 
 static int regulator_summary_show_roots(struct device *dev, void *data)
@@ -4741,8 +4747,8 @@ static int regulator_summary_show_roots(struct device *dev, void *data)
 
 static int regulator_summary_show(struct seq_file *s, void *data)
 {
-	seq_puts(s, " regulator                      use open bypass voltage current     min     max\n");
-	seq_puts(s, "-------------------------------------------------------------------------------\n");
+	seq_puts(s, " regulator                      use open bypass  opmode voltage current     min     max\n");
+	seq_puts(s, "---------------------------------------------------------------------------------------\n");
 
 	class_for_each_device(&regulator_class, NULL, s,
 			      regulator_summary_show_roots);

drivers/regulator/da9052-regulator.c

@@ -420,7 +420,7 @@ static int da9052_regulator_probe(struct platform_device *pdev)
 	config.dev = &pdev->dev;
 	config.driver_data = regulator;
 	config.regmap = da9052->regmap;
-	if (pdata && pdata->regulators) {
+	if (pdata) {
 		config.init_data = pdata->regulators[cell->id];
 	} else {
 #ifdef CONFIG_OF

drivers/regulator/da9055-regulator.c

@@ -612,7 +612,7 @@ static int da9055_regulator_probe(struct platform_device *pdev)
 	config.driver_data = regulator;
 	config.regmap = da9055->regmap;
 
-	if (pdata && pdata->regulators) {
+	if (pdata) {
 		config.init_data = pdata->regulators[pdev->id];
 	} else {
 		ret = da9055_regulator_dt_init(pdev, regulator, &config,

drivers/regulator/da9211-regulator.c

@@ -294,11 +294,11 @@ static struct da9211_pdata *da9211_parse_regulators_dt(
 		pdata->init_data[n] = da9211_matches[i].init_data;
 		pdata->reg_node[n] = da9211_matches[i].of_node;
 		pdata->gpiod_ren[n] = devm_gpiod_get_from_of_node(dev,
-								  da9211_matches[i].of_node,
-								  "enable",
-								  0,
-								  GPIOD_OUT_HIGH,
-								  "da9211-enable");
+				  da9211_matches[i].of_node,
+				  "enable",
+				  0,
+				  GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE,
+				  "da9211-enable");
 		n++;
 	}
 

drivers/regulator/fixed-helper.c

@@ -43,7 +43,6 @@ struct platform_device *regulator_register_always_on(int id, const char *name,
 	}
 
 	data->cfg.microvolts = uv;
-	data->cfg.gpio = -EINVAL;
 	data->cfg.enabled_at_boot = 1;
 	data->cfg.init_data = &data->init_data;
 

drivers/regulator/fixed.c

@@ -24,10 +24,9 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/fixed.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/slab.h>
 #include <linux/of.h>
-#include <linux/of_gpio.h>
 #include <linux/regulator/of_regulator.h>
 #include <linux/regulator/machine.h>
 
@@ -78,15 +77,16 @@ of_get_fixed_voltage_config(struct device *dev,
 	if (init_data->constraints.boot_on)
 		config->enabled_at_boot = true;
 
-	config->gpio = of_get_named_gpio(np, "gpio", 0);
-	if ((config->gpio < 0) && (config->gpio != -ENOENT))
-		return ERR_PTR(config->gpio);
-
 	of_property_read_u32(np, "startup-delay-us", &config->startup_delay);
 
-	config->enable_high = of_property_read_bool(np, "enable-active-high");
-	config->gpio_is_open_drain = of_property_read_bool(np,
-							   "gpio-open-drain");
+	/*
+	 * FIXME: we pulled active low/high and open drain handling into
+	 * gpiolib so it will be handled there. Delete this in the second
+	 * step when we also remove the custom inversion handling for all
+	 * legacy boardfiles.
+	 */
+	config->enable_high = 1;
+	config->gpio_is_open_drain = 0;
 
 	if (of_find_property(np, "vin-supply", NULL))
 		config->input_supply = "vin";
@@ -102,6 +102,7 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev)
 	struct fixed_voltage_config *config;
 	struct fixed_voltage_data *drvdata;
 	struct regulator_config cfg = { };
+	enum gpiod_flags gflags;
 	int ret;
 
 	drvdata = devm_kzalloc(&pdev->dev, sizeof(struct fixed_voltage_data),
@@ -150,25 +151,41 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev)
 
 	drvdata->desc.fixed_uV = config->microvolts;
 
-	if (gpio_is_valid(config->gpio)) {
-		cfg.ena_gpio = config->gpio;
-		if (pdev->dev.of_node)
-			cfg.ena_gpio_initialized = true;
-	}
 	cfg.ena_gpio_invert = !config->enable_high;
 	if (config->enabled_at_boot) {
 		if (config->enable_high)
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH;
+			gflags = GPIOD_OUT_HIGH;
 		else
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW;
+			gflags = GPIOD_OUT_LOW;
 	} else {
 		if (config->enable_high)
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW;
+			gflags = GPIOD_OUT_LOW;
 		else
-			cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH;
+			gflags = GPIOD_OUT_HIGH;
 	}
-	if (config->gpio_is_open_drain)
-		cfg.ena_gpio_flags |= GPIOF_OPEN_DRAIN;
+	if (config->gpio_is_open_drain) {
+		if (gflags == GPIOD_OUT_HIGH)
+			gflags = GPIOD_OUT_HIGH_OPEN_DRAIN;
+		else
+			gflags = GPIOD_OUT_LOW_OPEN_DRAIN;
+	}
+
+	/*
+	 * Some fixed regulators share the enable line between two
+	 * regulators which makes it necessary to get a handle on the
+	 * same descriptor for two different consumers. This will get
+	 * the GPIO descriptor, but only the first call will initialize
+	 * it so any flags such as inversion or open drain will only
+	 * be set up by the first caller and assumed identical on the
+	 * next caller.
+	 *
+	 * FIXME: find a better way to deal with this.
+	 */
+	gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
+
+	cfg.ena_gpiod = devm_gpiod_get_optional(&pdev->dev, NULL, gflags);
+	if (IS_ERR(cfg.ena_gpiod))
+		return PTR_ERR(cfg.ena_gpiod);
 
 	cfg.dev = &pdev->dev;
 	cfg.init_data = config->init_data;

drivers/regulator/helpers.c

@@ -103,6 +103,128 @@ int regulator_disable_regmap(struct regulator_dev *rdev)
 }
 EXPORT_SYMBOL_GPL(regulator_disable_regmap);
 
+static int regulator_range_selector_to_index(struct regulator_dev *rdev,
+					     unsigned int rval)
+{
+	int i;
+
+	if (!rdev->desc->linear_range_selectors)
+		return -EINVAL;
+
+	rval &= rdev->desc->vsel_range_mask;
+
+	for (i = 0; i < rdev->desc->n_linear_ranges; i++) {
+		if (rdev->desc->linear_range_selectors[i] == rval)
+			return i;
+	}
+	return -EINVAL;
+}
+
+/**
+ * regulator_get_voltage_sel_pickable_regmap - pickable range get_voltage_sel
+ *
+ * @rdev: regulator to operate on
+ *
+ * Regulators that use regmap for their register I/O and use pickable
+ * ranges can set the vsel_reg, vsel_mask, vsel_range_reg and vsel_range_mask
+ * fields in their descriptor and then use this as their get_voltage_vsel
+ * operation, saving some code.
+ */
+int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev)
+{
+	unsigned int r_val;
+	int range;
+	unsigned int val;
+	int ret, i;
+	unsigned int voltages_in_range = 0;
+
+	if (!rdev->desc->linear_ranges)
+		return -EINVAL;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
+	if (ret != 0)
+		return ret;
+
+	ret = regmap_read(rdev->regmap, rdev->desc->vsel_range_reg, &r_val);
+	if (ret != 0)
+		return ret;
+
+	val &= rdev->desc->vsel_mask;
+	val >>= ffs(rdev->desc->vsel_mask) - 1;
+
+	range = regulator_range_selector_to_index(rdev, r_val);
+	if (range < 0)
+		return -EINVAL;
+
+	for (i = 0; i < range; i++)
+		voltages_in_range += (rdev->desc->linear_ranges[i].max_sel -
+				     rdev->desc->linear_ranges[i].min_sel) + 1;
+
+	return val + voltages_in_range;
+}
+EXPORT_SYMBOL_GPL(regulator_get_voltage_sel_pickable_regmap);
+
+/**
+ * regulator_set_voltage_sel_pickable_regmap - pickable range set_voltage_sel
+ *
+ * @rdev: regulator to operate on
+ * @sel: Selector to set
+ *
+ * Regulators that use regmap for their register I/O and use pickable
+ * ranges can set the vsel_reg, vsel_mask, vsel_range_reg and vsel_range_mask
+ * fields in their descriptor and then use this as their set_voltage_vsel
+ * operation, saving some code.
+ */
+int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev,
+					      unsigned int sel)
+{
+	unsigned int range;
+	int ret, i;
+	unsigned int voltages_in_range = 0;
+
+	for (i = 0; i < rdev->desc->n_linear_ranges; i++) {
+		voltages_in_range = (rdev->desc->linear_ranges[i].max_sel -
+				     rdev->desc->linear_ranges[i].min_sel) + 1;
+		if (sel < voltages_in_range)
+			break;
+		sel -= voltages_in_range;
+	}
+
+	if (i == rdev->desc->n_linear_ranges)
+		return -EINVAL;
+
+	sel <<= ffs(rdev->desc->vsel_mask) - 1;
+	sel += rdev->desc->linear_ranges[i].min_sel;
+
+	range = rdev->desc->linear_range_selectors[i];
+
+	if (rdev->desc->vsel_reg == rdev->desc->vsel_range_reg) {
+		ret = regmap_update_bits(rdev->regmap,
+					 rdev->desc->vsel_reg,
+					 rdev->desc->vsel_range_mask |
+					 rdev->desc->vsel_mask, sel | range);
+	} else {
+		ret = regmap_update_bits(rdev->regmap,
+					 rdev->desc->vsel_range_reg,
+					 rdev->desc->vsel_range_mask, range);
+		if (ret)
+			return ret;
+
+		ret = regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
+				  rdev->desc->vsel_mask, sel);
+	}
+
+	if (ret)
+		return ret;
+
+	if (rdev->desc->apply_bit)
+		ret = regmap_update_bits(rdev->regmap, rdev->desc->apply_reg,
+					 rdev->desc->apply_bit,
+					 rdev->desc->apply_bit);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_set_voltage_sel_pickable_regmap);
+
 /**
  * regulator_get_voltage_sel_regmap - standard get_voltage_sel for regmap users
  *
@@ -321,20 +443,91 @@ int regulator_map_voltage_linear_range(struct regulator_dev *rdev,
 
 		ret += range->min_sel;
 
-		break;
+		/*
+		 * Map back into a voltage to verify we're still in bounds.
+		 * If we are not, then continue checking rest of the ranges.
+		 */
+		voltage = rdev->desc->ops->list_voltage(rdev, ret);
+		if (voltage >= min_uV && voltage <= max_uV)
+			break;
 	}
 
 	if (i == rdev->desc->n_linear_ranges)
 		return -EINVAL;
 
-	/* Map back into a voltage to verify we're still in bounds */
-	voltage = rdev->desc->ops->list_voltage(rdev, ret);
-	if (voltage < min_uV || voltage > max_uV)
+	return ret;
+}
+EXPORT_SYMBOL_GPL(regulator_map_voltage_linear_range);
+
+/**
+ * regulator_map_voltage_pickable_linear_range - map_voltage, pickable ranges
+ *
+ * @rdev: Regulator to operate on
+ * @min_uV: Lower bound for voltage
+ * @max_uV: Upper bound for voltage
+ *
+ * Drivers providing pickable linear_ranges in their descriptor can use
+ * this as their map_voltage() callback.
+ */
+int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev,
+						int min_uV, int max_uV)
+{
+	const struct regulator_linear_range *range;
+	int ret = -EINVAL;
+	int voltage, i;
+	unsigned int selector = 0;
+
+	if (!rdev->desc->n_linear_ranges) {
+		BUG_ON(!rdev->desc->n_linear_ranges);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < rdev->desc->n_linear_ranges; i++) {
+		int linear_max_uV;
+
+		range = &rdev->desc->linear_ranges[i];
+		linear_max_uV = range->min_uV +
+			(range->max_sel - range->min_sel) * range->uV_step;
+
+		if (!(min_uV <= linear_max_uV && max_uV >= range->min_uV)) {
+			selector += (range->max_sel - range->min_sel + 1);
+			continue;
+		}
+
+		if (min_uV <= range->min_uV)
+			min_uV = range->min_uV;
+
+		/* range->uV_step == 0 means fixed voltage range */
+		if (range->uV_step == 0) {
+			ret = 0;
+		} else {
+			ret = DIV_ROUND_UP(min_uV - range->min_uV,
+					   range->uV_step);
+			if (ret < 0)
+				return ret;
+		}
+
+		ret += selector;
+
+		voltage = rdev->desc->ops->list_voltage(rdev, ret);
+
+		/*
+		 * Map back into a voltage to verify we're still in bounds.
+		 * We may have overlapping voltage ranges. Hence we don't
+		 * exit but retry until we have checked all ranges.
+		 */
+		if (voltage < min_uV || voltage > max_uV)
+			selector += (range->max_sel - range->min_sel + 1);
+		else
+			break;
+	}
+
+	if (i == rdev->desc->n_linear_ranges)
 		return -EINVAL;
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(regulator_map_voltage_linear_range);
+EXPORT_SYMBOL_GPL(regulator_map_voltage_pickable_linear_range);
 
 /**
  * regulator_list_voltage_linear - List voltages with simple calculation
@@ -360,6 +553,46 @@ int regulator_list_voltage_linear(struct regulator_dev *rdev,
 }
 EXPORT_SYMBOL_GPL(regulator_list_voltage_linear);
 
+/**
+ * regulator_list_voltage_pickable_linear_range - pickable range list voltages
+ *
+ * @rdev: Regulator device
+ * @selector: Selector to convert into a voltage
+ *
+ * list_voltage() operation, intended to be used by drivers utilizing pickable
+ * ranges helpers.
+ */
+int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev,
+						 unsigned int selector)
+{
+	const struct regulator_linear_range *range;
+	int i;
+	unsigned int all_sels = 0;
+
+	if (!rdev->desc->n_linear_ranges) {
+		BUG_ON(!rdev->desc->n_linear_ranges);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < rdev->desc->n_linear_ranges; i++) {
+		unsigned int sels_in_range;
+
+		range = &rdev->desc->linear_ranges[i];
+
+		sels_in_range = range->max_sel - range->min_sel;
+
+		if (all_sels + sels_in_range >= selector) {
+			selector -= all_sels;
+			return range->min_uV + (range->uV_step * selector);
+		}
+
+		all_sels += (sels_in_range + 1);
+	}
+
+	return -EINVAL;
+}
+EXPORT_SYMBOL_GPL(regulator_list_voltage_pickable_linear_range);
+
 /**
  * regulator_list_voltage_linear_range - List voltages for linear ranges
  *

drivers/regulator/isl9305.c

@@ -84,6 +84,7 @@ static const struct regulator_desc isl9305_regulators[] = {
 		.enable_mask =	ISL9305_DCD1_EN,
 		.supply_name =	"VINDCD1",
 		.ops =		&isl9305_ops,
+		.owner =	THIS_MODULE,
 	},
 	[ISL9305_DCD2] = {
 		.name =		"DCD2",
@@ -98,6 +99,7 @@ static const struct regulator_desc isl9305_regulators[] = {
 		.enable_mask =	ISL9305_DCD2_EN,
 		.supply_name =	"VINDCD2",
 		.ops =		&isl9305_ops,
+		.owner =	THIS_MODULE,
 	},
 	[ISL9305_LDO1] = {
 		.name =		"LDO1",
@@ -112,6 +114,7 @@ static const struct regulator_desc isl9305_regulators[] = {
 		.enable_mask =	ISL9305_LDO1_EN,
 		.supply_name =	"VINLDO1",
 		.ops =		&isl9305_ops,
+		.owner =	THIS_MODULE,
 	},
 	[ISL9305_LDO2] = {
 		.name =		"LDO2",
@@ -126,6 +129,7 @@ static const struct regulator_desc isl9305_regulators[] = {
 		.enable_mask =	ISL9305_LDO2_EN,
 		.supply_name =	"VINLDO2",
 		.ops =		&isl9305_ops,
+		.owner =	THIS_MODULE,
 	},
 };
 

drivers/regulator/lm363x-regulator.c

@@ -227,9 +227,11 @@ static struct gpio_desc *lm363x_regulator_of_get_enable_gpio(struct device *dev,
 	 */
 	switch (id) {
 	case LM3632_LDO_POS:
-		return devm_gpiod_get_index_optional(dev, "enable", 0, GPIOD_OUT_LOW);
+		return devm_gpiod_get_index_optional(dev, "enable", 0,
+				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	case LM3632_LDO_NEG:
-		return devm_gpiod_get_index_optional(dev, "enable", 1, GPIOD_OUT_LOW);
+		return devm_gpiod_get_index_optional(dev, "enable", 1,
+				GPIOD_OUT_LOW | GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	default:
 		return NULL;
 	}

drivers/regulator/lochnagar-regulator.c

+// SPDX-License-Identifier: GPL-2.0
+//
+// Lochnagar regulator driver
+//
+// Copyright (c) 2017-2018 Cirrus Logic, Inc. and
+//                         Cirrus Logic International Semiconductor Ltd.
+//
+// Author: Charles Keepax <ckeepax@opensource.cirrus.com>
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+
+#include <linux/mfd/lochnagar.h>
+
+static const struct regulator_ops lochnagar_micvdd_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
+
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+};
+
+static const struct regulator_linear_range lochnagar_micvdd_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1000000, 0,    0xC, 50000),
+	REGULATOR_LINEAR_RANGE(1700000, 0xD, 0x1F, 100000),
+};
+
+static int lochnagar_micbias_enable(struct regulator_dev *rdev)
+{
+	struct lochnagar *lochnagar = rdev_get_drvdata(rdev);
+	int ret;
+
+	mutex_lock(&lochnagar->analogue_config_lock);
+
+	ret = regulator_enable_regmap(rdev);
+	if (ret < 0)
+		goto err;
+
+	ret = lochnagar_update_config(lochnagar);
+
+err:
+	mutex_unlock(&lochnagar->analogue_config_lock);
+
+	return ret;
+}
+
+static int lochnagar_micbias_disable(struct regulator_dev *rdev)
+{
+	struct lochnagar *lochnagar = rdev_get_drvdata(rdev);
+	int ret;
+
+	mutex_lock(&lochnagar->analogue_config_lock);
+
+	ret = regulator_disable_regmap(rdev);
+	if (ret < 0)
+		goto err;
+
+	ret = lochnagar_update_config(lochnagar);
+
+err:
+	mutex_unlock(&lochnagar->analogue_config_lock);
+
+	return ret;
+}
+
+static const struct regulator_ops lochnagar_micbias_ops = {
+	.enable = lochnagar_micbias_enable,
+	.disable = lochnagar_micbias_disable,
+	.is_enabled = regulator_is_enabled_regmap,
+};
+
+static const struct regulator_ops lochnagar_vddcore_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+
+	.list_voltage = regulator_list_voltage_linear_range,
+	.map_voltage = regulator_map_voltage_linear_range,
+
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+};
+
+static const struct regulator_linear_range lochnagar_vddcore_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, 0x8, 0x41, 12500),
+};
+
+enum lochnagar_regulators {
+	LOCHNAGAR_MICVDD,
+	LOCHNAGAR_MIC1VDD,
+	LOCHNAGAR_MIC2VDD,
+	LOCHNAGAR_VDDCORE,
+};
+
+static int lochnagar_micbias_of_parse(struct device_node *np,
+				      const struct regulator_desc *desc,
+				      struct regulator_config *config)
+{
+	struct lochnagar *lochnagar = config->driver_data;
+	int shift = (desc->id - LOCHNAGAR_MIC1VDD) *
+		    LOCHNAGAR2_P2_MICBIAS_SRC_SHIFT;
+	int mask = LOCHNAGAR2_P1_MICBIAS_SRC_MASK << shift;
+	unsigned int val;
+	int ret;
+
+	ret = of_property_read_u32(np, "cirrus,micbias-input", &val);
+	if (ret >= 0) {
+		mutex_lock(&lochnagar->analogue_config_lock);
+		ret = regmap_update_bits(lochnagar->regmap,
+					 LOCHNAGAR2_ANALOGUE_PATH_CTRL2,
+					 mask, val << shift);
+		mutex_unlock(&lochnagar->analogue_config_lock);
+		if (ret < 0) {
+			dev_err(lochnagar->dev,
+				"Failed to update micbias source: %d\n", ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static const struct regulator_desc lochnagar_regulators[] = {
+	[LOCHNAGAR_MICVDD] = {
+		.name = "MICVDD",
+		.supply_name = "SYSVDD",
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 32,
+		.ops = &lochnagar_micvdd_ops,
+
+		.id = LOCHNAGAR_MICVDD,
+		.of_match = of_match_ptr("MICVDD"),
+
+		.enable_reg = LOCHNAGAR2_MICVDD_CTRL1,
+		.enable_mask = LOCHNAGAR2_MICVDD_REG_ENA_MASK,
+		.vsel_reg = LOCHNAGAR2_MICVDD_CTRL2,
+		.vsel_mask = LOCHNAGAR2_MICVDD_VSEL_MASK,
+
+		.linear_ranges = lochnagar_micvdd_ranges,
+		.n_linear_ranges = ARRAY_SIZE(lochnagar_micvdd_ranges),
+
+		.enable_time = 3000,
+		.ramp_delay = 1000,
+
+		.owner = THIS_MODULE,
+	},
+	[LOCHNAGAR_MIC1VDD] = {
+		.name = "MIC1VDD",
+		.supply_name = "MICBIAS1",
+		.type = REGULATOR_VOLTAGE,
+		.ops = &lochnagar_micbias_ops,
+
+		.id = LOCHNAGAR_MIC1VDD,
+		.of_match = of_match_ptr("MIC1VDD"),
+		.of_parse_cb = lochnagar_micbias_of_parse,
+
+		.enable_reg = LOCHNAGAR2_ANALOGUE_PATH_CTRL2,
+		.enable_mask = LOCHNAGAR2_P1_INPUT_BIAS_ENA_MASK,
+
+		.owner = THIS_MODULE,
+	},
+	[LOCHNAGAR_MIC2VDD] = {
+		.name = "MIC2VDD",
+		.supply_name = "MICBIAS2",
+		.type = REGULATOR_VOLTAGE,
+		.ops = &lochnagar_micbias_ops,
+
+		.id = LOCHNAGAR_MIC2VDD,
+		.of_match = of_match_ptr("MIC2VDD"),
+		.of_parse_cb = lochnagar_micbias_of_parse,
+
+		.enable_reg = LOCHNAGAR2_ANALOGUE_PATH_CTRL2,
+		.enable_mask = LOCHNAGAR2_P2_INPUT_BIAS_ENA_MASK,
+
+		.owner = THIS_MODULE,
+	},
+	[LOCHNAGAR_VDDCORE] = {
+		.name = "VDDCORE",
+		.supply_name = "SYSVDD",
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 57,
+		.ops = &lochnagar_vddcore_ops,
+
+		.id = LOCHNAGAR_VDDCORE,
+		.of_match = of_match_ptr("VDDCORE"),
+
+		.enable_reg = LOCHNAGAR2_VDDCORE_CDC_CTRL1,
+		.enable_mask = LOCHNAGAR2_VDDCORE_CDC_REG_ENA_MASK,
+		.vsel_reg = LOCHNAGAR2_VDDCORE_CDC_CTRL2,
+		.vsel_mask = LOCHNAGAR2_VDDCORE_CDC_VSEL_MASK,
+
+		.linear_ranges = lochnagar_vddcore_ranges,
+		.n_linear_ranges = ARRAY_SIZE(lochnagar_vddcore_ranges),
+
+		.enable_time = 3000,
+		.ramp_delay = 1000,
+
+		.owner = THIS_MODULE,
+	},
+};
+
+static int lochnagar_regulator_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct lochnagar *lochnagar = dev_get_drvdata(dev->parent);
+	struct regulator_config config = { };
+	struct regulator_dev *rdev;
+	int ret, i;
+
+	config.dev = lochnagar->dev;
+	config.regmap = lochnagar->regmap;
+	config.driver_data = lochnagar;
+
+	for (i = 0; i < ARRAY_SIZE(lochnagar_regulators); i++) {
+		const struct regulator_desc *desc = &lochnagar_regulators[i];
+
+		rdev = devm_regulator_register(dev, desc, &config);
+		if (IS_ERR(rdev)) {
+			ret = PTR_ERR(rdev);
+			dev_err(dev, "Failed to register %s regulator: %d\n",
+				desc->name, ret);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static struct platform_driver lochnagar_regulator_driver = {
+	.driver = {
+		.name = "lochnagar-regulator",
+	},
+
+	.probe = lochnagar_regulator_probe,
+};
+module_platform_driver(lochnagar_regulator_driver);
+
+MODULE_AUTHOR("Charles Keepax <ckeepax@opensource.cirrus.com>");
+MODULE_DESCRIPTION("Regulator driver for Cirrus Logic Lochnagar Board");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:lochnagar-regulator");

drivers/regulator/lp8788-ldo.c

@@ -503,9 +503,10 @@ static int lp8788_config_ldo_enable_mode(struct platform_device *pdev,
 
 	/* FIXME: check default mode for GPIO here: high or low? */
 	ldo->ena_gpiod = devm_gpiod_get_index_optional(&pdev->dev,
-						       "enable",
-						       enable_id,
-						       GPIOD_OUT_HIGH);
+					       "enable",
+					       enable_id,
+					       GPIOD_OUT_HIGH |
+					       GPIOD_FLAGS_BIT_NONEXCLUSIVE);
 	if (IS_ERR(ldo->ena_gpiod))
 		return PTR_ERR(ldo->ena_gpiod);
 

drivers/regulator/max8952.c

@@ -230,6 +230,7 @@ static int max8952_pmic_probe(struct i2c_client *client,
 		gflags = GPIOD_OUT_HIGH;
 	else
 		gflags = GPIOD_OUT_LOW;
+	gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
 	gpiod = devm_gpiod_get_optional(&client->dev,
 					"max8952,en",
 					gflags);

drivers/regulator/max8973-regulator.c

@@ -758,6 +758,7 @@ static int max8973_probe(struct i2c_client *client,
 			gflags = GPIOD_OUT_HIGH;
 		else
 			gflags = GPIOD_OUT_LOW;
+		gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
 		gpiod = devm_gpiod_get_optional(&client->dev,
 						"maxim,enable",
 						gflags);

drivers/regulator/max8997-regulator.c

@@ -929,8 +929,8 @@ static int max8997_pmic_dt_parse_pdata(struct platform_device *pdev,
 				break;
 
 		if (i == ARRAY_SIZE(regulators)) {
-			dev_warn(&pdev->dev, "don't know how to configure regulator %s\n",
-				 reg_np->name);
+			dev_warn(&pdev->dev, "don't know how to configure regulator %pOFn\n",
+				 reg_np);
 			continue;
 		}
 

drivers/regulator/mc13xxx-regulator-core.c

@@ -203,7 +203,7 @@ struct mc13xxx_regulator_init_data *mc13xxx_parse_regulators_dt(
 
 		if (!found)
 			dev_warn(&pdev->dev,
-				 "Unknown regulator: %s\n", child->name);
+				 "Unknown regulator: %pOFn\n", child);
 	}
 	of_node_put(parent);
 

drivers/regulator/of_regulator.c

@@ -95,8 +95,8 @@ static void of_get_regulation_constraints(struct device_node *np,
 	if (!ret)
 		constraints->settling_time_up = pval;
 	if (constraints->settling_time_up && constraints->settling_time) {
-		pr_warn("%s: ambiguous configuration for settling time, ignoring 'regulator-settling-time-up-us'\n",
-			np->name);
+		pr_warn("%pOFn: ambiguous configuration for settling time, ignoring 'regulator-settling-time-up-us'\n",
+			np);
 		constraints->settling_time_up = 0;
 	}
 
@@ -105,8 +105,8 @@ static void of_get_regulation_constraints(struct device_node *np,
 	if (!ret)
 		constraints->settling_time_down = pval;
 	if (constraints->settling_time_down && constraints->settling_time) {
-		pr_warn("%s: ambiguous configuration for settling time, ignoring 'regulator-settling-time-down-us'\n",
-			np->name);
+		pr_warn("%pOFn: ambiguous configuration for settling time, ignoring 'regulator-settling-time-down-us'\n",
+			np);
 		constraints->settling_time_down = 0;
 	}
 
@@ -127,12 +127,12 @@ static void of_get_regulation_constraints(struct device_node *np,
 		if (desc && desc->of_map_mode) {
 			mode = desc->of_map_mode(pval);
 			if (mode == REGULATOR_MODE_INVALID)
-				pr_err("%s: invalid mode %u\n", np->name, pval);
+				pr_err("%pOFn: invalid mode %u\n", np, pval);
 			else
 				constraints->initial_mode = mode;
 		} else {
-			pr_warn("%s: mapping for mode %d not defined\n",
-				np->name, pval);
+			pr_warn("%pOFn: mapping for mode %d not defined\n",
+				np, pval);
 		}
 	}
 
@@ -144,14 +144,14 @@ static void of_get_regulation_constraints(struct device_node *np,
 				ret = of_property_read_u32_index(np,
 					"regulator-allowed-modes", i, &pval);
 				if (ret) {
-					pr_err("%s: couldn't read allowed modes index %d, ret=%d\n",
-						np->name, i, ret);
+					pr_err("%pOFn: couldn't read allowed modes index %d, ret=%d\n",
+						np, i, ret);
 					break;
 				}
 				mode = desc->of_map_mode(pval);
 				if (mode == REGULATOR_MODE_INVALID)
-					pr_err("%s: invalid regulator-allowed-modes element %u\n",
-						np->name, pval);
+					pr_err("%pOFn: invalid regulator-allowed-modes element %u\n",
+						np, pval);
 				else
 					constraints->valid_modes_mask |= mode;
 			}
@@ -159,7 +159,7 @@ static void of_get_regulation_constraints(struct device_node *np,
 				constraints->valid_ops_mask
 					|= REGULATOR_CHANGE_MODE;
 		} else {
-			pr_warn("%s: mode mapping not defined\n", np->name);
+			pr_warn("%pOFn: mode mapping not defined\n", np);
 		}
 	}
 
@@ -197,13 +197,13 @@ static void of_get_regulation_constraints(struct device_node *np,
 			if (desc && desc->of_map_mode) {
 				mode = desc->of_map_mode(pval);
 				if (mode == REGULATOR_MODE_INVALID)
-					pr_err("%s: invalid mode %u\n",
-					       np->name, pval);
+					pr_err("%pOFn: invalid mode %u\n",
+					       np, pval);
 				else
 					suspend_state->mode = mode;
 			} else {
-				pr_warn("%s: mapping for mode %d not defined\n",
-					np->name, pval);
+				pr_warn("%pOFn: mapping for mode %d not defined\n",
+					np, pval);
 			}
 		}
 
@@ -349,8 +349,8 @@ int of_regulator_match(struct device *dev, struct device_node *node,
 							   match->desc);
 			if (!match->init_data) {
 				dev_err(dev,
-					"failed to parse DT for regulator %s\n",
-					child->name);
+					"failed to parse DT for regulator %pOFn\n",
+					child);
 				of_node_put(child);
 				return -EINVAL;
 			}
@@ -399,16 +399,16 @@ struct regulator_init_data *regulator_of_get_init_data(struct device *dev,
 		init_data = of_get_regulator_init_data(dev, child, desc);
 		if (!init_data) {
 			dev_err(dev,
-				"failed to parse DT for regulator %s\n",
-				child->name);
+				"failed to parse DT for regulator %pOFn\n",
+				child);
 			break;
 		}
 
 		if (desc->of_parse_cb) {
 			if (desc->of_parse_cb(child, desc, config)) {
 				dev_err(dev,
-					"driver callback failed to parse DT for regulator %s\n",
-					child->name);
+					"driver callback failed to parse DT for regulator %pOFn\n",
+					child);
 				init_data = NULL;
 				break;
 			}

drivers/regulator/qcom-rpmh-regulator.c

@@ -414,7 +414,7 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
 			break;
 
 	if (!rpmh_data->name) {
-		dev_err(dev, "Unknown regulator %s\n", node->name);
+		dev_err(dev, "Unknown regulator %pOFn\n", node);
 		return -EINVAL;
 	}
 
@@ -423,8 +423,8 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
 
 	vreg->addr = cmd_db_read_addr(rpmh_resource_name);
 	if (!vreg->addr) {
-		dev_err(dev, "%s: could not find RPMh address for resource %s\n",
-			node->name, rpmh_resource_name);
+		dev_err(dev, "%pOFn: could not find RPMh address for resource %s\n",
+			node, rpmh_resource_name);
 		return -ENODEV;
 	}
 
@@ -469,13 +469,13 @@ static int rpmh_regulator_init_vreg(struct rpmh_vreg *vreg, struct device *dev,
 	rdev = devm_regulator_register(dev, &vreg->rdesc, &reg_config);
 	if (IS_ERR(rdev)) {
 		ret = PTR_ERR(rdev);
-		dev_err(dev, "%s: devm_regulator_register() failed, ret=%d\n",
-			node->name, ret);
+		dev_err(dev, "%pOFn: devm_regulator_register() failed, ret=%d\n",
+			node, ret);
 		return ret;
 	}
 
-	dev_dbg(dev, "%s regulator registered for RPMh resource %s @ 0x%05X\n",
-		node->name, rpmh_resource_name, vreg->addr);
+	dev_dbg(dev, "%pOFn regulator registered for RPMh resource %s @ 0x%05X\n",
+		node, rpmh_resource_name, vreg->addr);
 
 	return 0;
 }
@@ -504,6 +504,7 @@ static unsigned int rpmh_regulator_pmic4_ldo_of_map_mode(unsigned int rpmh_mode)
 		break;
 	default:
 		mode = REGULATOR_MODE_INVALID;
+		break;
 	}
 
 	return mode;
@@ -537,6 +538,7 @@ rpmh_regulator_pmic4_smps_of_map_mode(unsigned int rpmh_mode)
 		break;
 	default:
 		mode = REGULATOR_MODE_INVALID;
+		break;
 	}
 
 	return mode;
@@ -566,6 +568,7 @@ static unsigned int rpmh_regulator_pmic4_bob_of_map_mode(unsigned int rpmh_mode)
 		break;
 	default:
 		mode = REGULATOR_MODE_INVALID;
+		break;
 	}
 
 	return mode;

drivers/regulator/qcom_smd-regulator.c

@@ -420,6 +420,60 @@ static const struct regulator_desc pmi8998_bob = {
 	.ops = &rpm_bob_ops,
 };
 
+static const struct regulator_desc pms405_hfsmps3 = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(320000, 0, 215, 8000),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 216,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pms405_nldo300 = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 128,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pms405_nldo1200 = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(312000, 0, 127, 8000),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 128,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pms405_pldo50 = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(1664000, 0, 128, 16000),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 129,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pms405_pldo150 = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(1664000, 0, 128, 16000),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 129,
+	.ops = &rpm_smps_ldo_ops,
+};
+
+static const struct regulator_desc pms405_pldo600 = {
+	.linear_ranges = (struct regulator_linear_range[]) {
+		REGULATOR_LINEAR_RANGE(1256000, 0, 98, 8000),
+	},
+	.n_linear_ranges = 1,
+	.n_voltages = 99,
+	.ops = &rpm_smps_ldo_ops,
+};
+
 struct rpm_regulator_data {
 	const char *name;
 	u32 type;
@@ -661,6 +715,28 @@ static const struct rpm_regulator_data rpm_pmi8998_regulators[] = {
 	{}
 };
 
+static const struct rpm_regulator_data rpm_pms405_regulators[] = {
+	{ "s1", QCOM_SMD_RPM_SMPA, 1, &pms405_hfsmps3, "vdd_s1" },
+	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pms405_hfsmps3, "vdd_s2" },
+	{ "s3", QCOM_SMD_RPM_SMPA, 3, &pms405_hfsmps3, "vdd_s3" },
+	{ "s4", QCOM_SMD_RPM_SMPA, 4, &pms405_hfsmps3, "vdd_s4" },
+	{ "s5", QCOM_SMD_RPM_SMPA, 5, &pms405_hfsmps3, "vdd_s5" },
+	{ "l1", QCOM_SMD_RPM_LDOA, 1, &pms405_nldo1200, "vdd_l1_l2" },
+	{ "l2", QCOM_SMD_RPM_LDOA, 2, &pms405_nldo1200, "vdd_l1_l2" },
+	{ "l3", QCOM_SMD_RPM_LDOA, 3, &pms405_nldo1200, "vdd_l3_l8" },
+	{ "l4", QCOM_SMD_RPM_LDOA, 4, &pms405_nldo300, "vdd_l4" },
+	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pms405_pldo600, "vdd_l5_l6" },
+	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pms405_pldo600, "vdd_l5_l6" },
+	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pms405_pldo150, "vdd_l7" },
+	{ "l8", QCOM_SMD_RPM_LDOA, 8, &pms405_nldo1200, "vdd_l3_l8" },
+	{ "l9", QCOM_SMD_RPM_LDOA, 9, &pms405_nldo1200, "vdd_l9" },
+	{ "l10", QCOM_SMD_RPM_LDOA, 10, &pms405_pldo50, "vdd_l10_l11_l12_l13" },
+	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pms405_pldo150, "vdd_l10_l11_l12_l13" },
+	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pms405_pldo150, "vdd_l10_l11_l12_l13" },
+	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pms405_pldo150, "vdd_l10_l11_l12_l13" },
+	{}
+};
+
 static const struct of_device_id rpm_of_match[] = {
 	{ .compatible = "qcom,rpm-pm8841-regulators", .data = &rpm_pm8841_regulators },
 	{ .compatible = "qcom,rpm-pm8916-regulators", .data = &rpm_pm8916_regulators },
@@ -669,6 +745,7 @@ static const struct of_device_id rpm_of_match[] = {
 	{ .compatible = "qcom,rpm-pm8998-regulators", .data = &rpm_pm8998_regulators },
 	{ .compatible = "qcom,rpm-pma8084-regulators", .data = &rpm_pma8084_regulators },
 	{ .compatible = "qcom,rpm-pmi8998-regulators", .data = &rpm_pmi8998_regulators },
+	{ .compatible = "qcom,rpm-pms405-regulators", .data = &rpm_pms405_regulators },
 	{}
 };
 MODULE_DEVICE_TABLE(of, rpm_of_match);

drivers/regulator/s5m8767.c

@@ -447,15 +447,15 @@ static void s5m8767_regulator_config_ext_control(struct s5m8767_info *s5m8767,
 	}
 	if (mode != S5M8767_ENCTRL_USE_GPIO) {
 		dev_warn(s5m8767->dev,
-				"ext-control for %s: mismatched op_mode (%x), ignoring\n",
-				rdata->reg_node->name, mode);
+				"ext-control for %pOFn: mismatched op_mode (%x), ignoring\n",
+				rdata->reg_node, mode);
 		return;
 	}
 
 	if (!rdata->ext_control_gpiod) {
 		dev_warn(s5m8767->dev,
-				"ext-control for %s: GPIO not valid, ignoring\n",
-			 rdata->reg_node->name);
+				"ext-control for %pOFn: GPIO not valid, ignoring\n",
+			 rdata->reg_node);
 		return;
 	}
 
@@ -566,17 +566,18 @@ static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
 
 		if (i == ARRAY_SIZE(regulators)) {
 			dev_warn(iodev->dev,
-			"don't know how to configure regulator %s\n",
-			reg_np->name);
+			"don't know how to configure regulator %pOFn\n",
+			reg_np);
 			continue;
 		}
 
-		rdata->ext_control_gpiod = devm_gpiod_get_from_of_node(&pdev->dev,
-								       reg_np,
-								       "s5m8767,pmic-ext-control-gpios",
-								       0,
-								       GPIOD_OUT_HIGH,
-								       "s5m8767");
+		rdata->ext_control_gpiod = devm_gpiod_get_from_of_node(
+			&pdev->dev,
+			reg_np,
+			"s5m8767,pmic-ext-control-gpios",
+			0,
+			GPIOD_OUT_HIGH | GPIOD_FLAGS_BIT_NONEXCLUSIVE,
+			"s5m8767");
 		if (IS_ERR(rdata->ext_control_gpiod))
 			return PTR_ERR(rdata->ext_control_gpiod);
 

drivers/regulator/tps65090-regulator.c

@@ -374,6 +374,7 @@ static struct tps65090_platform_data *tps65090_parse_dt_reg_data(
 				gflags = GPIOD_OUT_HIGH;
 			else
 				gflags = GPIOD_OUT_LOW;
+			gflags |= GPIOD_FLAGS_BIT_NONEXCLUSIVE;
 
 			rpdata->gpiod = devm_gpiod_get_from_of_node(&pdev->dev,
 								    tps65090_matches[idx].of_node,

include/linux/gpio/consumer.h

@@ -30,6 +30,7 @@ struct gpio_descs {
 #define GPIOD_FLAGS_BIT_DIR_OUT		BIT(1)
 #define GPIOD_FLAGS_BIT_DIR_VAL		BIT(2)
 #define GPIOD_FLAGS_BIT_OPEN_DRAIN	BIT(3)
+#define GPIOD_FLAGS_BIT_NONEXCLUSIVE	BIT(4)
 
 /**
  * Optional flags that can be passed to one of gpiod_* to configure direction

include/linux/regulator/driver.h

@@ -271,9 +271,16 @@ enum regulator_type {
  * @ramp_delay: Time to settle down after voltage change (unit: uV/us)
  * @min_dropout_uV: The minimum dropout voltage this regulator can handle
  * @linear_ranges: A constant table of possible voltage ranges.
- * @n_linear_ranges: Number of entries in the @linear_ranges table.
+ * @linear_range_selectors: A constant table of voltage range selectors.
+ *			    If pickable ranges are used each range must
+ *			    have corresponding selector here.
+ * @n_linear_ranges: Number of entries in the @linear_ranges (and in
+ *		     linear_range_selectors if used) table(s).
  * @volt_table: Voltage mapping table (if table based mapping)
  *
+ * @vsel_range_reg: Register for range selector when using pickable ranges
+ *		    and regulator_regmap_X_voltage_X_pickable functions.
+ * @vsel_range_mask: Mask for register bitfield used for range selector
  * @vsel_reg: Register for selector when using regulator_regmap_X_voltage_
  * @vsel_mask: Mask for register bitfield used for selector
  * @csel_reg: Register for TPS65218 LS3 current regulator
@@ -338,10 +345,14 @@ struct regulator_desc {
 	int min_dropout_uV;
 
 	const struct regulator_linear_range *linear_ranges;
+	const unsigned int *linear_range_selectors;
+
 	int n_linear_ranges;
 
 	const unsigned int *volt_table;
 
+	unsigned int vsel_range_reg;
+	unsigned int vsel_range_mask;
 	unsigned int vsel_reg;
 	unsigned int vsel_mask;
 	unsigned int csel_reg;
@@ -498,18 +509,25 @@ int regulator_mode_to_status(unsigned int);
 
 int regulator_list_voltage_linear(struct regulator_dev *rdev,
 				  unsigned int selector);
+int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev,
+						   unsigned int selector);
 int regulator_list_voltage_linear_range(struct regulator_dev *rdev,
 					unsigned int selector);
 int regulator_list_voltage_table(struct regulator_dev *rdev,
 				  unsigned int selector);
 int regulator_map_voltage_linear(struct regulator_dev *rdev,
 				  int min_uV, int max_uV);
+int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev,
+						  int min_uV, int max_uV);
 int regulator_map_voltage_linear_range(struct regulator_dev *rdev,
 				       int min_uV, int max_uV);
 int regulator_map_voltage_iterate(struct regulator_dev *rdev,
 				  int min_uV, int max_uV);
 int regulator_map_voltage_ascend(struct regulator_dev *rdev,
 				  int min_uV, int max_uV);
+int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev);
+int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev,
+						unsigned int sel);
 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev);
 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel);
 int regulator_is_enabled_regmap(struct regulator_dev *rdev);

include/linux/regulator/fixed.h

@@ -24,8 +24,6 @@ struct regulator_init_data;
  * @supply_name:	Name of the regulator supply
  * @input_supply:	Name of the input regulator supply
  * @microvolts:		Output voltage of regulator
- * @gpio:		GPIO to use for enable control
- * 			set to -EINVAL if not used
  * @startup_delay:	Start-up time in microseconds
  * @gpio_is_open_drain: Gpio pin is open drain or normal type.
  *			If it is open drain type then HIGH will be set
@@ -49,7 +47,6 @@ struct fixed_voltage_config {
 	const char *supply_name;
 	const char *input_supply;
 	int microvolts;
-	int gpio;
 	unsigned startup_delay;
 	unsigned gpio_is_open_drain:1;
 	unsigned enable_high:1;