Commit 515fdd77 authored by Bjorn Helgaas's avatar Bjorn Helgaas Committed by Linus Torvalds

[PATCH] Add PCDP console detection support

Add support for the EFI/DIG PCDP console discovery table (see
http://www.dig64.org/specifications/DIG64_HCDPv20_042804.pdf).

This moves the code from drivers/serial/8250_hcdp.[ch] to
drivers/firmware/pcdp.[ch], since it's no longer 8250-specific.  It also
obsoletes CONFIG_SERIAL_8250_HCDP, replacing it with CONFIG_EFI_PCDP (which
defaults to Y for ia64).

In a nutshell, HCDP tells us "these UARTs are available for use as a
console," and it's up to the user to explicitly specify the console device.
 The kernel can guess in some cases, but not all.

The PCDP (aka HCDP v2) tells us what we really want to know, namely, "this
UART or VGA device is the console device." (It also has provision for
support for new device types.)
Signed-off-by: default avatarBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@osdl.org>
parent d6e0677c
...@@ -319,31 +319,30 @@ setup_arch (char **cmdline_p) ...@@ -319,31 +319,30 @@ setup_arch (char **cmdline_p)
#ifdef CONFIG_ACPI_BOOT #ifdef CONFIG_ACPI_BOOT
acpi_boot_init(); acpi_boot_init();
#endif #endif
#ifdef CONFIG_SERIAL_8250_CONSOLE #ifdef CONFIG_EFI_PCDP
#ifdef CONFIG_SERIAL_8250_HCDP efi_setup_pcdp_console(*cmdline_p);
if (efi.hcdp) {
void setup_serial_hcdp(void *);
setup_serial_hcdp(efi.hcdp);
}
#endif #endif
#ifdef CONFIG_SERIAL_8250_CONSOLE
if (!efi.hcdp) if (!efi.hcdp)
setup_serial_legacy(); setup_serial_legacy();
#endif #endif
#ifdef CONFIG_VT #ifdef CONFIG_VT
if (!conswitchp) {
# if defined(CONFIG_DUMMY_CONSOLE) # if defined(CONFIG_DUMMY_CONSOLE)
conswitchp = &dummy_con; conswitchp = &dummy_con;
# endif # endif
# if defined(CONFIG_VGA_CONSOLE) # if defined(CONFIG_VGA_CONSOLE)
/* /*
* Non-legacy systems may route legacy VGA MMIO range to system * Non-legacy systems may route legacy VGA MMIO range to system
* memory. vga_con probes the MMIO hole, so memory looks like * memory. vga_con probes the MMIO hole, so memory looks like
* a VGA device to it. The EFI memory map can tell us if it's * a VGA device to it. The EFI memory map can tell us if it's
* memory so we can avoid this problem. * memory so we can avoid this problem.
*/ */
if (efi_mem_type(0xA0000) != EFI_CONVENTIONAL_MEMORY) if (efi_mem_type(0xA0000) != EFI_CONVENTIONAL_MEMORY)
conswitchp = &vga_con; conswitchp = &vga_con;
# endif # endif
}
#endif #endif
/* enable IA-64 Machine Check Abort Handling */ /* enable IA-64 Machine Check Abort Handling */
......
...@@ -34,4 +34,23 @@ config EFI_VARS ...@@ -34,4 +34,23 @@ config EFI_VARS
Subsequent efibootmgr releases may be found at: Subsequent efibootmgr releases may be found at:
http://linux.dell.com/efibootmgr http://linux.dell.com/efibootmgr
config EFI_PCDP
bool "Console device selection via EFI PCDP or HCDP table"
depends on ACPI && EFI && IA64
default y if IA64
help
If your firmware supplies the PCDP table, and you want to
automatically use the primary console device it describes
as the Linux console, say Y here.
If your firmware supplies the HCDP table, and you want to
use the first serial port it describes as the Linux console,
say Y here. If your EFI ConOut path contains only a UART
device, it will become the console automatically. Otherwise,
you must specify the "console=ttyS0" kernel boot argument.
You must also enable the appropriate drivers (serial, VGA, etc.)
See <http://www.dig64.org/specifications/DIG64_HCDPv20_042804.pdf>
endmenu endmenu
...@@ -3,3 +3,4 @@ ...@@ -3,3 +3,4 @@
# #
obj-$(CONFIG_EDD) += edd.o obj-$(CONFIG_EDD) += edd.o
obj-$(CONFIG_EFI_VARS) += efivars.o obj-$(CONFIG_EFI_VARS) += efivars.o
obj-$(CONFIG_EFI_PCDP) += pcdp.o
/*
* Copyright (C) 2002, 2003, 2004 Hewlett-Packard Co.
* Khalid Aziz <khalid_aziz@hp.com>
* Alex Williamson <alex.williamson@hp.com>
* Bjorn Helgaas <bjorn.helgaas@hp.com>
*
* Parse the EFI PCDP table to locate the console device.
*/
#include <linux/acpi.h>
#include <linux/console.h>
#include <linux/efi.h>
#include <linux/tty.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <asm/serial.h>
#include "pcdp.h"
static inline int
uart_irq_supported(int rev, struct pcdp_uart *uart)
{
if (rev < 3)
return uart->pci_func & PCDP_UART_IRQ;
return uart->flags & PCDP_UART_IRQ;
}
static inline int
uart_pci(int rev, struct pcdp_uart *uart)
{
if (rev < 3)
return uart->pci_func & PCDP_UART_PCI;
return uart->flags & PCDP_UART_PCI;
}
static inline int
uart_active_high_low(int rev, struct pcdp_uart *uart)
{
if (uart_pci(rev, uart) || uart->flags & PCDP_UART_ACTIVE_LOW)
return ACPI_ACTIVE_LOW;
return ACPI_ACTIVE_HIGH;
}
static inline int
uart_edge_level(int rev, struct pcdp_uart *uart)
{
if (uart_pci(rev, uart))
return ACPI_LEVEL_SENSITIVE;
if (rev < 3 || uart->flags & PCDP_UART_EDGE_SENSITIVE)
return ACPI_EDGE_SENSITIVE;
return ACPI_LEVEL_SENSITIVE;
}
static void __init
setup_serial_console(int rev, struct pcdp_uart *uart)
{
#ifdef CONFIG_SERIAL_8250_CONSOLE
struct uart_port port;
static char options[16];
memset(&port, 0, sizeof(port));
port.uartclk = uart->clock_rate;
if (!port.uartclk) /* some FW doesn't supply this */
port.uartclk = BASE_BAUD * 16;
if (uart->addr.address_space_id == ACPI_ADR_SPACE_SYSTEM_MEMORY) {
port.mapbase = uart->addr.address;
port.membase = ioremap(port.mapbase, 64);
port.iotype = SERIAL_IO_MEM;
} else if (uart->addr.address_space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
port.iobase = uart->addr.address;
port.iotype = SERIAL_IO_PORT;
} else
return;
switch (uart->pci_prog_intfc) {
case 0x0: port.type = PORT_8250; break;
case 0x1: port.type = PORT_16450; break;
case 0x2: port.type = PORT_16550; break;
case 0x3: port.type = PORT_16650; break;
case 0x4: port.type = PORT_16750; break;
case 0x5: port.type = PORT_16850; break;
case 0x6: port.type = PORT_16C950; break;
default: port.type = PORT_UNKNOWN; break;
}
port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_RESOURCES;
if (uart_irq_supported(rev, uart)) {
port.irq = acpi_register_gsi(uart->gsi,
uart_active_high_low(rev, uart),
uart_edge_level(rev, uart));
port.flags |= UPF_AUTO_IRQ; /* some FW reported wrong GSI */
if (uart_pci(rev, uart))
port.flags |= UPF_SHARE_IRQ;
}
if (early_serial_setup(&port) < 0)
return;
snprintf(options, sizeof(options), "%lun%d", uart->baud,
uart->bits ? uart->bits : 8);
add_preferred_console("ttyS", port.line, options);
printk(KERN_INFO "PCDP: serial console at %s 0x%lx (ttyS%d, options %s)\n",
port.iotype == SERIAL_IO_MEM ? "MMIO" : "I/O",
uart->addr.address, port.line, options);
#endif
}
static void __init
setup_vga_console(struct pcdp_vga *vga)
{
#ifdef CONFIG_VT
#ifdef CONFIG_VGA_CONSOLE
if (efi_mem_type(0xA0000) == EFI_CONVENTIONAL_MEMORY) {
printk(KERN_ERR "PCDP: VGA selected, but frame buffer is not MMIO!\n");
return;
}
conswitchp = &vga_con;
printk(KERN_INFO "PCDP: VGA console\n");
#endif
#endif
}
void __init
efi_setup_pcdp_console(char *cmdline)
{
struct pcdp *pcdp;
struct pcdp_uart *uart;
struct pcdp_device *dev, *end;
int i, serial = 0;
pcdp = efi.hcdp;
if (!pcdp)
return;
printk(KERN_INFO "PCDP: v%d at 0x%p\n", pcdp->rev, pcdp);
if (pcdp->rev < 3) {
if (strstr(cmdline, "console=ttyS0") || efi_uart_console_only())
serial = 1;
}
for (i = 0, uart = pcdp->uart; i < pcdp->num_uarts; i++, uart++) {
if (uart->flags & PCDP_UART_PRIMARY_CONSOLE || serial) {
if (uart->type == PCDP_CONSOLE_UART) {
setup_serial_console(pcdp->rev, uart);
return;
}
}
}
end = (struct pcdp_device *) ((u8 *) pcdp + pcdp->length);
for (dev = (struct pcdp_device *) (pcdp->uart + pcdp->num_uarts);
dev < end;
dev = (struct pcdp_device *) ((u8 *) dev + dev->length)) {
if (dev->flags & PCDP_PRIMARY_CONSOLE) {
if (dev->type == PCDP_CONSOLE_VGA) {
setup_vga_console((struct pcdp_vga *) dev);
return;
}
}
}
}
#ifdef CONFIG_IA64_EARLY_PRINTK_UART
unsigned long
hcdp_early_uart (void)
{
efi_system_table_t *systab;
efi_config_table_t *config_tables;
unsigned long addr = 0;
struct pcdp *pcdp = 0;
struct pcdp_uart *uart;
int i;
systab = (efi_system_table_t *) ia64_boot_param->efi_systab;
if (!systab)
return 0;
systab = __va(systab);
config_tables = (efi_config_table_t *) systab->tables;
if (!config_tables)
return 0;
config_tables = __va(config_tables);
for (i = 0; i < systab->nr_tables; i++) {
if (efi_guidcmp(config_tables[i].guid, PCDP_TABLE_GUID) == 0) {
pcdp = (struct pcdp *) config_tables[i].table;
break;
}
}
if (!pcdp)
return 0;
pcdp = __va(pcdp);
for (i = 0, uart = pcdp->uart; i < pcdp->num_uarts; i++, uart++) {
if (uart->type == PCDP_CONSOLE_UART) {
addr = uart->addr.address;
break;
}
}
return addr;
}
#endif /* CONFIG_IA64_EARLY_PRINTK_UART */
/*
* Copyright (C) 2002, 2004 Hewlett-Packard Co.
* Khalid Aziz <khalid_aziz@hp.com>
* Bjorn Helgaas <bjorn.helgaas@hp.com>
*
* Definitions for PCDP-defined console devices
*
* v1.0a: http://www.dig64.org/specifications/DIG64_HCDPv10a_01.pdf
* v2.0: http://www.dig64.org/specifications/DIG64_HCDPv20_042804.pdf
*/
#define PCDP_CONSOLE 0
#define PCDP_DEBUG 1
#define PCDP_CONSOLE_OUTPUT 2
#define PCDP_CONSOLE_INPUT 3
#define PCDP_UART (0 << 3)
#define PCDP_VGA (1 << 3)
#define PCDP_USB (2 << 3)
/* pcdp_uart.type and pcdp_device.type */
#define PCDP_CONSOLE_UART (PCDP_UART | PCDP_CONSOLE)
#define PCDP_DEBUG_UART (PCDP_UART | PCDP_DEBUG)
#define PCDP_CONSOLE_VGA (PCDP_VGA | PCDP_CONSOLE_OUTPUT)
#define PCDP_CONSOLE_USB (PCDP_USB | PCDP_CONSOLE_INPUT)
/* pcdp_uart.flags */
#define PCDP_UART_EDGE_SENSITIVE (1 << 0)
#define PCDP_UART_ACTIVE_LOW (1 << 1)
#define PCDP_UART_PRIMARY_CONSOLE (1 << 2)
#define PCDP_UART_IRQ (1 << 6) /* in pci_func for rev < 3 */
#define PCDP_UART_PCI (1 << 7) /* in pci_func for rev < 3 */
struct pcdp_uart {
u8 type;
u8 bits;
u8 parity;
u8 stop_bits;
u8 pci_seg;
u8 pci_bus;
u8 pci_dev;
u8 pci_func;
u64 baud;
struct acpi_generic_address addr;
u16 pci_dev_id;
u16 pci_vendor_id;
u32 gsi;
u32 clock_rate;
u8 pci_prog_intfc;
u8 flags;
};
struct pcdp_vga {
u8 count; /* address space descriptors */
};
/* pcdp_device.flags */
#define PCDP_PRIMARY_CONSOLE 1
struct pcdp_device {
u8 type;
u8 flags;
u16 length;
u16 efi_index;
};
struct pcdp {
u8 signature[4];
u32 length;
u8 rev; /* PCDP v2.0 is rev 3 */
u8 chksum;
u8 oemid[6];
u8 oem_tabid[8];
u32 oem_rev;
u8 creator_id[4];
u32 creator_rev;
u32 num_uarts;
struct pcdp_uart uart[0]; /* actual size is num_uarts */
/* remainder of table is pcdp_device structures */
};
/*
* linux/drivers/char/hcdp_serial.c
*
* Copyright (C) 2002 Hewlett-Packard Co.
* Khalid Aziz <khalid_aziz@hp.com>
*
* Parse the EFI HCDP table to locate serial console and debug ports and
* initialize them.
*
* 2002/08/29 davidm Adjust it to new 2.5 serial driver infrastructure.
*/
#include <linux/config.h>
#include <linux/console.h>
#include <linux/kernel.h>
#include <linux/efi.h>
#include <linux/init.h>
#include <linux/tty.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <linux/types.h>
#include <linux/acpi.h>
#include <asm/io.h>
#include <asm/serial.h>
#include <asm/acpi.h>
#include "8250_hcdp.h"
#undef SERIAL_DEBUG_HCDP
/*
* Parse the HCDP table to find descriptions for headless console and debug
* serial ports and add them to rs_table[]. A pointer to HCDP table is
* passed as parameter. This function should be called before
* serial_console_init() is called to make sure the HCDP serial console will
* be available for use. IA-64 kernel calls this function from setup_arch()
* after the EFI and ACPI tables have been parsed.
*/
void __init
setup_serial_hcdp(void *tablep)
{
hcdp_dev_t *hcdp_dev;
struct uart_port port;
unsigned long iobase;
hcdp_t hcdp;
int gsi, nr;
static char options[16];
#if 0
static int shift_once = 1;
#endif
#ifdef SERIAL_DEBUG_HCDP
printk("Entering setup_serial_hcdp()\n");
#endif
/* Verify we have a valid table pointer */
if (!tablep)
return;
memset(&port, 0, sizeof(port));
/*
* Don't trust firmware to give us a table starting at an aligned
* address. Make a local copy of the HCDP table with aligned
* structures.
*/
memcpy(&hcdp, tablep, sizeof(hcdp));
/*
* Perform a sanity check on the table. Table should have a signature
* of "HCDP" and it should be atleast 82 bytes long to have any
* useful information.
*/
if ((strncmp(hcdp.signature, HCDP_SIGNATURE, HCDP_SIG_LEN) != 0))
return;
if (hcdp.len < 82)
return;
#ifdef SERIAL_DEBUG_HCDP
printk("setup_serial_hcdp(): table pointer = 0x%p, sig = '%.4s'\n",
tablep, hcdp.signature);
printk(" length = %d, rev = %d, ", hcdp.len, hcdp.rev);
printk("OEM ID = %.6s, # of entries = %d\n", hcdp.oemid,
hcdp.num_entries);
#endif
/*
* Parse each device entry
*/
for (nr = 0; nr < hcdp.num_entries; nr++) {
hcdp_dev = hcdp.hcdp_dev + nr;
/*
* We will parse only the primary console device which is
* the first entry for these devices. We will ignore rest
* of the entries for the same type device that has already
* been parsed and initialized
*/
if (hcdp_dev->type != HCDP_DEV_CONSOLE)
continue;
iobase = ((u64) hcdp_dev->base_addr.addrhi << 32) |
hcdp_dev->base_addr.addrlo;
gsi = hcdp_dev->global_int;
/* See PCI spec v2.2, Appendix D (Class Codes): */
switch (hcdp_dev->pci_prog_intfc) {
case 0x00:
port.type = PORT_8250;
break;
case 0x01:
port.type = PORT_16450;
break;
case 0x02:
port.type = PORT_16550;
break;
case 0x03:
port.type = PORT_16650;
break;
case 0x04:
port.type = PORT_16750;
break;
case 0x05:
port.type = PORT_16850;
break;
case 0x06:
port.type = PORT_16C950;
break;
default:
printk(KERN_WARNING "warning: EFI HCDP table reports "
"unknown serial programming interface 0x%02x; "
"will autoprobe.\n", hcdp_dev->pci_prog_intfc);
port.type = PORT_UNKNOWN;
break;
}
#ifdef SERIAL_DEBUG_HCDP
printk(" type = %s, uart = %d\n",
((hcdp_dev->type == HCDP_DEV_CONSOLE) ?
"Headless Console" :
((hcdp_dev->type == HCDP_DEV_DEBUG) ?
"Debug port" : "Huh????")), port.type);
printk(" base address space = %s, base address = 0x%lx\n",
((hcdp_dev->base_addr.space_id == ACPI_MEM_SPACE) ?
"Memory Space" :
((hcdp_dev->base_addr.space_id == ACPI_IO_SPACE) ?
"I/O space" : "PCI space")),
iobase);
printk(" gsi = %d, baud rate = %lu, bits = %d, clock = %d\n",
gsi, (unsigned long) hcdp_dev->baud, hcdp_dev->bits,
hcdp_dev->clock_rate);
if (HCDP_PCI_UART(hcdp_dev))
printk(" PCI id: %02x:%02x:%02x, vendor ID=0x%x, "
"dev ID=0x%x\n", hcdp_dev->pci_seg,
hcdp_dev->pci_bus, hcdp_dev->pci_dev,
hcdp_dev->pci_vendor_id, hcdp_dev->pci_dev_id);
#endif
/*
* Now fill in a port structure to update the 8250 port table..
*/
if (hcdp_dev->clock_rate)
port.uartclk = hcdp_dev->clock_rate;
else
port.uartclk = BASE_BAUD * 16;
/*
* Check if this is an I/O mapped address or a memory mapped
* address
*/
if (hcdp_dev->base_addr.space_id == ACPI_MEM_SPACE) {
port.iobase = 0;
port.mapbase = iobase;
port.membase = ioremap(iobase, 64);
port.iotype = SERIAL_IO_MEM;
} else if (hcdp_dev->base_addr.space_id == ACPI_IO_SPACE) {
port.iobase = iobase;
port.mapbase = 0;
port.membase = NULL;
port.iotype = SERIAL_IO_PORT;
} else if (hcdp_dev->base_addr.space_id == ACPI_PCICONF_SPACE) {
printk(KERN_WARNING"warning: No support for PCI serial console\n");
return;
}
if (HCDP_IRQ_SUPPORTED(hcdp_dev)) {
if (HCDP_PCI_UART(hcdp_dev))
port.irq = acpi_register_gsi(gsi,
ACPI_LEVEL_SENSITIVE, ACPI_ACTIVE_LOW);
else
port.irq = acpi_register_gsi(gsi,
ACPI_EDGE_SENSITIVE, ACPI_ACTIVE_HIGH);
port.flags |= UPF_AUTO_IRQ;
if (HCDP_PCI_UART(hcdp_dev))
port.flags |= UPF_SHARE_IRQ;
}
port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_RESOURCES;
/*
* Note: the above memset() initializes port.line to 0,
* so we register this port as ttyS0.
*/
if (early_serial_setup(&port) < 0) {
printk("setup_serial_hcdp(): early_serial_setup() "
"for HCDP serial console port failed. "
"Will try any additional consoles in HCDP.\n");
memset(&port, 0, sizeof(port));
continue;
}
if (efi_uart_console_only()) {
snprintf(options, sizeof(options), "%lun%d",
hcdp_dev->baud, hcdp_dev->bits);
add_preferred_console("ttyS", port.line, options);
}
break;
}
#ifdef SERIAL_DEBUG_HCDP
printk("Leaving setup_serial_hcdp()\n");
#endif
}
#ifdef CONFIG_IA64_EARLY_PRINTK_UART
unsigned long
hcdp_early_uart (void)
{
efi_system_table_t *systab;
efi_config_table_t *config_tables;
unsigned long addr = 0;
hcdp_t *hcdp = 0;
hcdp_dev_t *dev;
int i;
systab = (efi_system_table_t *) ia64_boot_param->efi_systab;
if (!systab)
return 0;
systab = __va(systab);
config_tables = (efi_config_table_t *) systab->tables;
if (!config_tables)
return 0;
config_tables = __va(config_tables);
for (i = 0; i < systab->nr_tables; i++) {
if (efi_guidcmp(config_tables[i].guid, HCDP_TABLE_GUID) == 0) {
hcdp = (hcdp_t *) config_tables[i].table;
break;
}
}
if (!hcdp)
return 0;
hcdp = __va(hcdp);
for (i = 0, dev = hcdp->hcdp_dev; i < hcdp->num_entries; i++, dev++) {
if (dev->type == HCDP_DEV_CONSOLE) {
addr = (u64) dev->base_addr.addrhi << 32 | dev->base_addr.addrlo;
break;
}
}
return addr;
}
#endif /* CONFIG_IA64_EARLY_PRINTK_UART */
/*
* drivers/serial/8250_hcdp.h
*
* Copyright (C) 2002 Hewlett-Packard Co.
* Khalid Aziz <khalid_aziz@hp.com>
*
* Definitions for HCDP defined serial ports (Serial console and debug
* ports)
*/
/* ACPI table signatures */
#define HCDP_SIG_LEN 4
#define HCDP_SIGNATURE "HCDP"
/* Space ID as defined in ACPI generic address structure */
#define ACPI_MEM_SPACE 0
#define ACPI_IO_SPACE 1
#define ACPI_PCICONF_SPACE 2
/*
* Maximum number of HCDP devices we want to read in
*/
#define MAX_HCDP_DEVICES 6
/*
* Default UART clock rate if clock rate is 0 in HCDP table.
*/
#define DEFAULT_UARTCLK 115200
/*
* ACPI Generic Address Structure
*/
typedef struct {
u8 space_id;
u8 bit_width;
u8 bit_offset;
u8 resv;
u32 addrlo;
u32 addrhi;
} acpi_gen_addr;
/* HCDP Device descriptor entry types */
#define HCDP_DEV_CONSOLE 0
#define HCDP_DEV_DEBUG 1
/* HCDP Device descriptor type */
typedef struct {
u8 type;
u8 bits;
u8 parity;
u8 stop_bits;
u8 pci_seg;
u8 pci_bus;
u8 pci_dev;
u8 pci_func;
u64 baud;
acpi_gen_addr base_addr;
u16 pci_dev_id;
u16 pci_vendor_id;
u32 global_int;
u32 clock_rate;
u8 pci_prog_intfc;
u8 resv;
} hcdp_dev_t;
/* HCDP Table format */
typedef struct {
u8 signature[4];
u32 len;
u8 rev;
u8 chksum;
u8 oemid[6];
u8 oem_tabid[8];
u32 oem_rev;
u8 creator_id[4];
u32 creator_rev;
u32 num_entries;
hcdp_dev_t hcdp_dev[MAX_HCDP_DEVICES];
} hcdp_t;
#define HCDP_PCI_UART(x) (x->pci_func & 1UL<<7)
#define HCDP_IRQ_SUPPORTED(x) (x->pci_func & 1UL<<6)
...@@ -62,15 +62,6 @@ config SERIAL_8250_CONSOLE ...@@ -62,15 +62,6 @@ config SERIAL_8250_CONSOLE
If unsure, say N. If unsure, say N.
config SERIAL_8250_HCDP
bool "Console device discovery via EFI HCDP table"
depends on IA64
depends on SERIAL_8250_CONSOLE=y
---help---
If you wish to make the serial console port described by the EFI
HCDP table available for use as serial console, say Y here. See
<http://www.dig64.org/specifications/DIG64_HCDPv10a_01.pdf>.
config SERIAL_8250_CS config SERIAL_8250_CS
tristate "8250/16550 PCMCIA device support" tristate "8250/16550 PCMCIA device support"
depends on PCMCIA && SERIAL_8250 depends on PCMCIA && SERIAL_8250
......
...@@ -9,7 +9,6 @@ serial-8250-$(CONFIG_SERIAL_8250_ACPI) += 8250_acpi.o ...@@ -9,7 +9,6 @@ serial-8250-$(CONFIG_SERIAL_8250_ACPI) += 8250_acpi.o
serial-8250-$(CONFIG_GSC) += 8250_gsc.o serial-8250-$(CONFIG_GSC) += 8250_gsc.o
serial-8250-$(CONFIG_PCI) += 8250_pci.o serial-8250-$(CONFIG_PCI) += 8250_pci.o
serial-8250-$(CONFIG_PNP) += 8250_pnp.o serial-8250-$(CONFIG_PNP) += 8250_pnp.o
serial-8250-$(CONFIG_SERIAL_8250_HCDP) += 8250_hcdp.o
obj-$(CONFIG_SERIAL_CORE) += serial_core.o obj-$(CONFIG_SERIAL_CORE) += serial_core.o
obj-$(CONFIG_SERIAL_21285) += 21285.o obj-$(CONFIG_SERIAL_21285) += 21285.o
......
...@@ -305,6 +305,10 @@ extern unsigned long __init efi_get_time(void); ...@@ -305,6 +305,10 @@ extern unsigned long __init efi_get_time(void);
extern int __init efi_set_rtc_mmss(unsigned long nowtime); extern int __init efi_set_rtc_mmss(unsigned long nowtime);
extern struct efi_memory_map memmap; extern struct efi_memory_map memmap;
#ifdef CONFIG_EFI_PCDP
extern void __init efi_setup_pcdp_console(char *);
#endif
/* /*
* We play games with efi_enabled so that the compiler will, if possible, remove * We play games with efi_enabled so that the compiler will, if possible, remove
* EFI-related code altogether. * EFI-related code altogether.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment