Merge tag 'tty-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
 "Here are some small TTY and Serial driver fixes for 5.16-rc4 to
  resolve a number of reported problems.

  They include:

   - liteuart serial driver fixes

   - 8250_pci serial driver fixes for pericom devices

   - 8250 RTS line control fix while in RS-485 mode

   - tegra serial driver fix

   - msm_serial driver fix

   - pl011 serial driver new id

   - fsl_lpuart revert of broken change

   - 8250_bcm7271 serial driver fix

   - MAINTAINERS file update for rpmsg tty driver that came in 5.16-rc1

   - vgacon fix for reported problem

  All of these, except for the 8250_bcm7271 fix have been in linux-next
  with no reported problem. The 8250_bcm7271 fix was added to the tree
  on Friday so no chance to be linux-next yet. But it should be fine as
  the affected developers submitted it"

* tag 'tty-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_bcm7271: UART errors after resuming from S2
  serial: 8250_pci: rewrite pericom_do_set_divisor()
  serial: 8250_pci: Fix ACCES entries in pci_serial_quirks array
  serial: 8250: Fix RTS modem control while in rs485 mode
  Revert "tty: serial: fsl_lpuart: drop earlycon entry for i.MX8QXP"
  serial: tegra: Change lower tolerance baud rate limit for tegra20 and tegra30
  serial: liteuart: relax compile-test dependencies
  serial: liteuart: fix minor-number leak on probe errors
  serial: liteuart: fix use-after-free and memleak on unbind
  serial: liteuart: Fix NULL pointer dereference in ->remove()
  vgacon: Propagate console boot parameters before calling `vc_resize'
  tty: serial: msm_serial: Deactivate RX DMA for polling support
  serial: pl011: Add ACPI SBSA UART match id
  serial: core: fix transmit-buffer reset and memleak
  MAINTAINERS: Add rpmsg tty driver maintainer

MAINTAINERS

@@ -16502,6 +16502,12 @@ T:	git git://linuxtv.org/media_tree.git
 F:	Documentation/devicetree/bindings/media/allwinner,sun8i-a83t-de2-rotate.yaml
 F:	drivers/media/platform/sunxi/sun8i-rotate/
 
+RPMSG TTY DRIVER
+M:	Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
+L:	linux-remoteproc@vger.kernel.org
+S:	Maintained
+F:	drivers/tty/rpmsg_tty.c
+
 RTL2830 MEDIA DRIVER
 M:	Antti Palosaari <crope@iki.fi>
 L:	linux-media@vger.kernel.org

drivers/tty/serial/8250/8250_bcm7271.c

@@ -237,6 +237,7 @@ struct brcmuart_priv {
 	u32		rx_err;
 	u32		rx_timeout;
 	u32		rx_abort;
+	u32		saved_mctrl;
 };
 
 static struct dentry *brcmuart_debugfs_root;
@@ -1133,16 +1134,27 @@ static int brcmuart_remove(struct platform_device *pdev)
 static int __maybe_unused brcmuart_suspend(struct device *dev)
 {
 	struct brcmuart_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	struct uart_port *port = &up->port;
 
 	serial8250_suspend_port(priv->line);
 	clk_disable_unprepare(priv->baud_mux_clk);
 
+	/*
+	 * This will prevent resume from enabling RTS before the
+	 *  baud rate has been resored.
+	 */
+	priv->saved_mctrl = port->mctrl;
+	port->mctrl = 0;
+
 	return 0;
 }
 
 static int __maybe_unused brcmuart_resume(struct device *dev)
 {
 	struct brcmuart_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	struct uart_port *port = &up->port;
 	int ret;
 
 	ret = clk_prepare_enable(priv->baud_mux_clk);
@@ -1165,6 +1177,7 @@ static int __maybe_unused brcmuart_resume(struct device *dev)
 		start_rx_dma(serial8250_get_port(priv->line));
 	}
 	serial8250_resume_port(priv->line);
+	port->mctrl = priv->saved_mctrl;
 	return 0;
 }
 

drivers/tty/serial/8250/8250_pci.c

@@ -1324,29 +1324,33 @@ pericom_do_set_divisor(struct uart_port *port, unsigned int baud,
 {
 	int scr;
 	int lcr;
-	int actual_baud;
-	int tolerance;
 
-	for (scr = 5 ; scr <= 15 ; scr++) {
-		actual_baud = 921600 * 16 / scr;
-		tolerance = actual_baud / 50;
+	for (scr = 16; scr > 4; scr--) {
+		unsigned int maxrate = port->uartclk / scr;
+		unsigned int divisor = max(maxrate / baud, 1U);
+		int delta = maxrate / divisor - baud;
 
-		if ((baud < actual_baud + tolerance) &&
-			(baud > actual_baud - tolerance)) {
+		if (baud > maxrate + baud / 50)
+			continue;
 
+		if (delta > baud / 50)
+			divisor++;
+
+		if (divisor > 0xffff)
+			continue;
+
+		/* Update delta due to possible divisor change */
+		delta = maxrate / divisor - baud;
+		if (abs(delta) < baud / 50) {
 			lcr = serial_port_in(port, UART_LCR);
 			serial_port_out(port, UART_LCR, lcr | 0x80);
-
-			serial_port_out(port, UART_DLL, 1);
-			serial_port_out(port, UART_DLM, 0);
+			serial_port_out(port, UART_DLL, divisor & 0xff);
+			serial_port_out(port, UART_DLM, divisor >> 8 & 0xff);
 			serial_port_out(port, 2, 16 - scr);
 			serial_port_out(port, UART_LCR, lcr);
 			return;
-		} else if (baud > actual_baud) {
-			break;
 		}
 	}
-	serial8250_do_set_divisor(port, baud, quot, quot_frac);
 }
 static int pci_pericom_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
@@ -2291,12 +2295,19 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
 		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
-		.vendor     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
 		.setup      = pci_pericom_setup_four_at_eight,
 	},
+	{
+		.vendor     = PCI_VENDOR_ID_ACCESIO,
+		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+		.subvendor  = PCI_ANY_ID,
+		.subdevice  = PCI_ANY_ID,
+		.setup      = pci_pericom_setup_four_at_eight,
+	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4,

drivers/tty/serial/8250/8250_port.c

@@ -2024,13 +2024,6 @@ void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned char mcr;
 
-	if (port->rs485.flags & SER_RS485_ENABLED) {
-		if (serial8250_in_MCR(up) & UART_MCR_RTS)
-			mctrl |= TIOCM_RTS;
-		else
-			mctrl &= ~TIOCM_RTS;
-	}
-
 	mcr = serial8250_TIOCM_to_MCR(mctrl);
 
 	mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;

drivers/tty/serial/Kconfig

@@ -1533,7 +1533,7 @@ config SERIAL_LITEUART
 	tristate "LiteUART serial port support"
 	depends on HAS_IOMEM
 	depends on OF || COMPILE_TEST
-	depends on LITEX
+	depends on LITEX || COMPILE_TEST
 	select SERIAL_CORE
 	help
 	  This driver is for the FPGA-based LiteUART serial controller from LiteX

drivers/tty/serial/amba-pl011.c

@@ -2947,6 +2947,7 @@ MODULE_DEVICE_TABLE(of, sbsa_uart_of_match);
 
 static const struct acpi_device_id __maybe_unused sbsa_uart_acpi_match[] = {
 	{ "ARMH0011", 0 },
+	{ "ARMHB000", 0 },
 	{},
 };
 MODULE_DEVICE_TABLE(acpi, sbsa_uart_acpi_match);

drivers/tty/serial/fsl_lpuart.c

@@ -2625,6 +2625,7 @@ OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
 OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1028a-lpuart", ls1028a_early_console_setup);
 OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup);
+OF_EARLYCON_DECLARE(lpuart32, "fsl,imx8qxp-lpuart", lpuart32_imx_early_console_setup);
 EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
 EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
 

drivers/tty/serial/liteuart.c

@@ -270,8 +270,10 @@ static int liteuart_probe(struct platform_device *pdev)
 
 	/* get membase */
 	port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, NULL);
-	if (IS_ERR(port->membase))
-		return PTR_ERR(port->membase);
+	if (IS_ERR(port->membase)) {
+		ret = PTR_ERR(port->membase);
+		goto err_erase_id;
+	}
 
 	/* values not from device tree */
 	port->dev = &pdev->dev;
@@ -285,7 +287,18 @@ static int liteuart_probe(struct platform_device *pdev)
 	port->line = dev_id;
 	spin_lock_init(&port->lock);
 
-	return uart_add_one_port(&liteuart_driver, &uart->port);
+	platform_set_drvdata(pdev, port);
+
+	ret = uart_add_one_port(&liteuart_driver, &uart->port);
+	if (ret)
+		goto err_erase_id;
+
+	return 0;
+
+err_erase_id:
+	xa_erase(&liteuart_array, uart->id);
+
+	return ret;
 }
 
 static int liteuart_remove(struct platform_device *pdev)
@@ -293,6 +306,7 @@ static int liteuart_remove(struct platform_device *pdev)
 	struct uart_port *port = platform_get_drvdata(pdev);
 	struct liteuart_port *uart = to_liteuart_port(port);
 
+	uart_remove_one_port(&liteuart_driver, port);
 	xa_erase(&liteuart_array, uart->id);
 
 	return 0;

drivers/tty/serial/msm_serial.c

@@ -598,6 +598,9 @@ static void msm_start_rx_dma(struct msm_port *msm_port)
 	u32 val;
 	int ret;
 
+	if (IS_ENABLED(CONFIG_CONSOLE_POLL))
+		return;
+
 	if (!dma->chan)
 		return;
 

drivers/tty/serial/serial-tegra.c

@@ -1506,7 +1506,7 @@ static struct tegra_uart_chip_data tegra20_uart_chip_data = {
 	.fifo_mode_enable_status	= false,
 	.uart_max_port			= 5,
 	.max_dma_burst_bytes		= 4,
-	.error_tolerance_low_range	= 0,
+	.error_tolerance_low_range	= -4,
 	.error_tolerance_high_range	= 4,
 };
 
@@ -1517,7 +1517,7 @@ static struct tegra_uart_chip_data tegra30_uart_chip_data = {
 	.fifo_mode_enable_status	= false,
 	.uart_max_port			= 5,
 	.max_dma_burst_bytes		= 4,
-	.error_tolerance_low_range	= 0,
+	.error_tolerance_low_range	= -4,
 	.error_tolerance_high_range	= 4,
 };
 

drivers/tty/serial/serial_core.c

@@ -1075,6 +1075,11 @@ uart_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear)
 		goto out;
 
 	if (!tty_io_error(tty)) {
+		if (uport->rs485.flags & SER_RS485_ENABLED) {
+			set &= ~TIOCM_RTS;
+			clear &= ~TIOCM_RTS;
+		}
+
 		uart_update_mctrl(uport, set, clear);
 		ret = 0;
 	}
@@ -1549,6 +1554,7 @@ static void uart_tty_port_shutdown(struct tty_port *port)
 {
 	struct uart_state *state = container_of(port, struct uart_state, port);
 	struct uart_port *uport = uart_port_check(state);
+	char *buf;
 
 	/*
 	 * At this point, we stop accepting input.  To do this, we
@@ -1570,8 +1576,18 @@ static void uart_tty_port_shutdown(struct tty_port *port)
 	 */
 	tty_port_set_suspended(port, 0);
 
-	uart_change_pm(state, UART_PM_STATE_OFF);
+	/*
+	 * Free the transmit buffer.
+	 */
+	spin_lock_irq(&uport->lock);
+	buf = state->xmit.buf;
+	state->xmit.buf = NULL;
+	spin_unlock_irq(&uport->lock);
 
+	if (buf)
+		free_page((unsigned long)buf);
+
+	uart_change_pm(state, UART_PM_STATE_OFF);
 }
 
 static void uart_wait_until_sent(struct tty_struct *tty, int timeout)

drivers/video/console/vgacon.c

@@ -366,11 +366,17 @@ static void vgacon_init(struct vc_data *c, int init)
 	struct uni_pagedir *p;
 
 	/*
-	 * We cannot be loaded as a module, therefore init is always 1,
-	 * but vgacon_init can be called more than once, and init will
-	 * not be 1.
+	 * We cannot be loaded as a module, therefore init will be 1
+	 * if we are the default console, however if we are a fallback
+	 * console, for example if fbcon has failed registration, then
+	 * init will be 0, so we need to make sure our boot parameters
+	 * have been copied to the console structure for vgacon_resize
+	 * ultimately called by vc_resize.  Any subsequent calls to
+	 * vgacon_init init will have init set to 0 too.
 	 */
 	c->vc_can_do_color = vga_can_do_color;
+	c->vc_scan_lines = vga_scan_lines;
+	c->vc_font.height = c->vc_cell_height = vga_video_font_height;
 
 	/* set dimensions manually if init != 0 since vc_resize() will fail */
 	if (init) {
@@ -379,8 +385,6 @@ static void vgacon_init(struct vc_data *c, int init)
 	} else
 		vc_resize(c, vga_video_num_columns, vga_video_num_lines);
 
-	c->vc_scan_lines = vga_scan_lines;
-	c->vc_font.height = c->vc_cell_height = vga_video_font_height;
 	c->vc_complement_mask = 0x7700;
 	if (vga_512_chars)
 		c->vc_hi_font_mask = 0x0800;