Commit 53884577 authored by Rakesh Pillai's avatar Rakesh Pillai Committed by Kalle Valo

ath10k: skip sending quiet mode cmd for WCN3990

HL2.0 firmware does not support setting quiet mode.  If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.

fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0

The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set.  10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().

Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: default avatarGovind Singh <govinds@codeaurora.org>
Co-developed-by: default avatarKalle Valo <kvalo@codeaurora.org>
Signed-off-by: default avatarRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: default avatarGovind Singh <govinds@codeaurora.org>
Signed-off-by: default avatarKalle Valo <kvalo@codeaurora.org>
parent eca1e56c
......@@ -2418,6 +2418,28 @@ static int ath10k_core_reset_rx_filter(struct ath10k *ar)
return 0;
}
static int ath10k_core_compat_services(struct ath10k *ar)
{
struct ath10k_fw_file *fw_file = &ar->normal_mode_fw.fw_file;
/* all 10.x firmware versions support thermal throttling but don't
* advertise the support via service flags so we have to hardcode
* it here
*/
switch (fw_file->wmi_op_version) {
case ATH10K_FW_WMI_OP_VERSION_10_1:
case ATH10K_FW_WMI_OP_VERSION_10_2:
case ATH10K_FW_WMI_OP_VERSION_10_2_4:
case ATH10K_FW_WMI_OP_VERSION_10_4:
set_bit(WMI_SERVICE_THERM_THROT, ar->wmi.svc_map);
break;
default:
break;
}
return 0;
}
int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
const struct ath10k_fw_components *fw)
{
......@@ -2617,6 +2639,12 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
goto err_hif_stop;
}
status = ath10k_core_compat_services(ar);
if (status) {
ath10k_err(ar, "compat services failed: %d\n", status);
goto err_hif_stop;
}
/* Some firmware revisions do not properly set up hardware rx filter
* registers.
*
......
......@@ -2578,8 +2578,9 @@ int ath10k_debug_register(struct ath10k *ar)
debugfs_create_file("pktlog_filter", 0644, ar->debug.debugfs_phy, ar,
&fops_pktlog_filter);
debugfs_create_file("quiet_period", 0644, ar->debug.debugfs_phy, ar,
&fops_quiet_period);
if (test_bit(WMI_SERVICE_THERM_THROT, ar->wmi.svc_map))
debugfs_create_file("quiet_period", 0644, ar->debug.debugfs_phy, ar,
&fops_quiet_period);
debugfs_create_file("tpc_stats", 0400, ar->debug.debugfs_phy, ar,
&fops_tpc_stats);
......
......@@ -140,6 +140,9 @@ void ath10k_thermal_set_throttling(struct ath10k *ar)
lockdep_assert_held(&ar->conf_mutex);
if (!test_bit(WMI_SERVICE_THERM_THROT, ar->wmi.svc_map))
return;
if (!ar->wmi.ops->gen_pdev_set_quiet_mode)
return;
......@@ -165,6 +168,9 @@ int ath10k_thermal_register(struct ath10k *ar)
struct device *hwmon_dev;
int ret;
if (!test_bit(WMI_SERVICE_THERM_THROT, ar->wmi.svc_map))
return 0;
cdev = thermal_cooling_device_register("ath10k_thermal", ar,
&ath10k_thermal_ops);
......@@ -216,6 +222,9 @@ int ath10k_thermal_register(struct ath10k *ar)
void ath10k_thermal_unregister(struct ath10k *ar)
{
if (!test_bit(WMI_SERVICE_THERM_THROT, ar->wmi.svc_map))
return;
sysfs_remove_link(&ar->dev->kobj, "cooling_device");
thermal_cooling_device_unregister(ar->thermal.cdev);
}
......@@ -1564,6 +1564,9 @@ wmi_tlv_svc_map_ext(const __le32 *in, unsigned long *out, size_t len)
SVCMAP(WMI_TLV_SERVICE_SPOOF_MAC_SUPPORT,
WMI_SERVICE_SPOOF_MAC_SUPPORT,
WMI_TLV_MAX_SERVICE);
SVCMAP(WMI_TLV_SERVICE_THERM_THROT,
WMI_SERVICE_THERM_THROT,
WMI_TLV_MAX_SERVICE);
}
#undef SVCMAP
......
......@@ -205,6 +205,7 @@ enum wmi_service {
WMI_SERVICE_SPOOF_MAC_SUPPORT,
WMI_SERVICE_TX_DATA_ACK_RSSI,
WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT,
WMI_SERVICE_THERM_THROT,
/* keep last */
WMI_SERVICE_MAX,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment