Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:
 "Here is another set of bugfixes for ARM SoCs, mostly harmless:

   - a boot regression fix on ux500

   - PCIe interrupts on NXP i.MX7 and on Marvell Armada 7K/8K were wired
     up wrong, in different ways

   - Armada XP support for large memory never worked

   - the socfpga reset controller now builds on 64-bit

   - minor device tree corrections on gemini, mvebu, r-pi 3, rockchip
     and at91"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: ux500: Fix regression while init PM domains
  ARM: dts: fix PCLK name on Gemini and MOXA ART
  arm64: dts: rockchip: fix typo in iommu nodes
  arm64: dts: rockchip: correct vqmmc voltage for rk3399 platforms
  ARM: dts: imx7d: Invert legacy PCI irq mapping
  bus: mbus: fix window size calculation for 4GB windows
  ARM: dts: at91: sama5d2: add ADC hw trigger edge type
  ARM: dts: at91: sama5d2_xplained: enable ADTRG pin
  ARM: dts: at91: at91-sama5d27_som1: fix PHY ID
  ARM: dts: bcm283x: Fix console path on RPi3
  reset: socfpga: fix for 64-bit compilation
  ARM: dts: Fix I2C repeated start issue on Armada-38x
  arm64: dts: marvell: fix interrupt-map property for Armada CP110 PCIe controller
  arm64: dts: salvator-common: add 12V regulator to backlight
  ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
  arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0

arch/arm/boot/dts/armada-38x.dtsi

@@ -178,7 +178,7 @@ gic: interrupt-controller@d000 {
 			};
 
 			i2c0: i2c@11000 {
-				compatible = "marvell,mv64xxx-i2c";
+				compatible = "marvell,mv78230-a0-i2c", "marvell,mv64xxx-i2c";
 				reg = <0x11000 0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -189,7 +189,7 @@ i2c0: i2c@11000 {
 			};
 
 			i2c1: i2c@11100 {
-				compatible = "marvell,mv64xxx-i2c";
+				compatible = "marvell,mv78230-a0-i2c", "marvell,mv64xxx-i2c";
 				reg = <0x11100 0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;

arch/arm/boot/dts/at91-sama5d27_som1.dtsi

@@ -67,8 +67,8 @@ macb0: ethernet@f8008000 {
 				pinctrl-0 = <&pinctrl_macb0_default>;
 				phy-mode = "rmii";
 
-				ethernet-phy@1 {
-					reg = <0x1>;
+				ethernet-phy@0 {
+					reg = <0x0>;
 					interrupt-parent = <&pioA>;
 					interrupts = <PIN_PD31 IRQ_TYPE_LEVEL_LOW>;
 					pinctrl-names = "default";

arch/arm/boot/dts/at91-sama5d2_xplained.dts

@@ -309,7 +309,7 @@ adc: adc@fc030000 {
 				vddana-supply = <&vdd_3v3_lp_reg>;
 				vref-supply = <&vdd_3v3_lp_reg>;
 				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_adc_default>;
+				pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
 				status = "okay";
 			};
 
@@ -340,6 +340,20 @@ pinctrl_can1_default: can1_default {
 					bias-disable;
 				};
 
+				/*
+				 * The ADTRG pin can work on any edge type.
+				 * In here it's being pulled up, so need to
+				 * connect it to ground to get an edge e.g.
+				 * Trigger can be configured on falling, rise
+				 * or any edge, and the pull-up can be changed
+				 * to pull-down or left floating according to
+				 * needs.
+				 */
+				pinctrl_adtrg_default: adtrg_default {
+					pinmux = <PIN_PD31__ADTRG>;
+					bias-pull-up;
+				};
+
 				pinctrl_charger_chglev: charger_chglev {
 					pinmux = <PIN_PA12__GPIO>;
 					bias-disable;

arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

@@ -18,12 +18,9 @@ / {
 	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
 	model = "Raspberry Pi Zero W";
 
-	/* Needed by firmware to properly init UARTs */
-	aliases {
-		uart0 = "/soc/serial@7e201000";
-		uart1 = "/soc/serial@7e215040";
-		serial0 = "/soc/serial@7e201000";
-		serial1 = "/soc/serial@7e215040";
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
 	};
 
 	leds {

arch/arm/boot/dts/bcm2837-rpi-3-b.dts

@@ -8,6 +8,11 @@ / {
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
 	model = "Raspberry Pi 3 Model B";
 
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
 	memory {
 		reg = <0 0x40000000>;
 	};

arch/arm/boot/dts/bcm283x.dtsi

@@ -20,8 +20,13 @@ / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
 	chosen {
-		bootargs = "earlyprintk console=ttyAMA0";
+		stdout-path = "serial0:115200n8";
 	};
 
 	thermal-zones {

arch/arm/boot/dts/gemini.dtsi

@@ -145,11 +145,12 @@ mux1 {
 		};
 
 		watchdog@41000000 {
-			compatible = "cortina,gemini-watchdog";
+			compatible = "cortina,gemini-watchdog", "faraday,ftwdt010";
 			reg = <0x41000000 0x1000>;
 			interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&syscon GEMINI_RESET_WDOG>;
 			clocks = <&syscon GEMINI_CLK_APB>;
+			clock-names = "PCLK";
 		};
 
 		uart0: serial@42000000 {

arch/arm/boot/dts/imx7d.dtsi

@@ -144,10 +144,10 @@ pcie: pcie@0x33800000 {
 		interrupt-names = "msi";
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0x7>;
-		interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-map = <0 0 0 1 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 2 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 3 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 4 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
 			 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
 			 <&clks IMX7D_PCIE_PHY_ROOT_CLK>;

arch/arm/boot/dts/moxart.dtsi

@@ -87,9 +87,10 @@ dma: dma@90500000 {
 		};
 
 		watchdog: watchdog@98500000 {
-			compatible = "moxa,moxart-watchdog";
+			compatible = "moxa,moxart-watchdog", "faraday,ftwdt010";
 			reg = <0x98500000 0x10>;
 			clocks = <&clk_apb>;
+			clock-names = "PCLK";
 		};
 
 		sdhci: sdhci@98e00000 {

arch/arm/boot/dts/sama5d2.dtsi

@@ -1430,6 +1430,7 @@ adc: adc@fc030000 {
 				atmel,min-sample-rate-hz = <200000>;
 				atmel,max-sample-rate-hz = <20000000>;
 				atmel,startup-time-ms = <4>;
+				atmel,trigger-edge-type = <IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/sun6i-a31.dtsi

@@ -311,8 +311,8 @@ tcon1_in: port@0 {
 					#size-cells = <0>;
 					reg = <0>;
 
-					tcon1_in_drc1: endpoint@0 {
-						reg = <0>;
+					tcon1_in_drc1: endpoint@1 {
+						reg = <1>;
 						remote-endpoint = <&drc1_out_tcon1>;
 					};
 				};
@@ -1012,8 +1012,8 @@ be1_out: port@1 {
 					#size-cells = <0>;
 					reg = <1>;
 
-					be1_out_drc1: endpoint@0 {
-						reg = <0>;
+					be1_out_drc1: endpoint@1 {
+						reg = <1>;
 						remote-endpoint = <&drc1_in_be1>;
 					};
 				};
@@ -1042,8 +1042,8 @@ drc1_in: port@0 {
 					#size-cells = <0>;
 					reg = <0>;
 
-					drc1_in_be1: endpoint@0 {
-						reg = <0>;
+					drc1_in_be1: endpoint@1 {
+						reg = <1>;
 						remote-endpoint = <&be1_out_drc1>;
 					};
 				};
@@ -1053,8 +1053,8 @@ drc1_out: port@1 {
 					#size-cells = <0>;
 					reg = <1>;
 
-					drc1_out_tcon1: endpoint@0 {
-						reg = <0>;
+					drc1_out_tcon1: endpoint@1 {
+						reg = <1>;
 						remote-endpoint = <&tcon1_in_drc1>;
 					};
 				};

arch/arm/mach-ux500/cpu-db8500.c

@@ -32,6 +32,7 @@
 #include <asm/mach/arch.h>
 
 #include "db8500-regs.h"
+#include "pm_domains.h"
 
 static int __init ux500_l2x0_unlock(void)
 {
@@ -157,6 +158,9 @@ static const struct of_device_id u8500_local_bus_nodes[] = {
 
 static void __init u8500_init_machine(void)
 {
+	/* Initialize ux500 power domains */
+	ux500_pm_domains_init();
+
 	/* automatically probe child nodes of dbx5x0 devices */
 	if (of_machine_is_compatible("st-ericsson,u8540"))
 		of_platform_populate(NULL, u8500_local_bus_nodes,

arch/arm/mach-ux500/pm.c

@@ -19,7 +19,6 @@
 #include <linux/of_address.h>
 
 #include "db8500-regs.h"
-#include "pm_domains.h"
 
 /* ARM WFI Standby signal register */
 #define PRCM_ARM_WFI_STANDBY    (prcmu_base + 0x130)
@@ -203,7 +202,4 @@ void __init ux500_pm_init(u32 phy_base, u32 size)
 
 	/* Set up ux500 suspend callbacks. */
 	suspend_set_ops(UX500_SUSPEND_OPS);
-
-	/* Initialize ux500 power domains */
-	ux500_pm_domains_init();
 }

arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts

@@ -61,13 +61,6 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
 };
 
 &ehci0 {
@@ -91,7 +84,7 @@ &i2c1_pins {
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
 	disable-wp;

arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi

@@ -336,7 +336,7 @@ cpm_pcie0: pcie@f2600000 {
 				/* non-prefetchable memory */
 				0x82000000 0 0xf6000000 0  0xf6000000 0 0xf00000>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cpm_icu 0 ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map = <0 0 0 0 &cpm_icu ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
 			interrupts = <ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
 			num-lanes = <1>;
 			clocks = <&cpm_clk 1 13>;
@@ -362,7 +362,7 @@ cpm_pcie1: pcie@f2620000 {
 				/* non-prefetchable memory */
 				0x82000000 0 0xf7000000 0  0xf7000000 0 0xf00000>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cpm_icu 0 ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map = <0 0 0 0 &cpm_icu ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
 			interrupts = <ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
 
 			num-lanes = <1>;
@@ -389,7 +389,7 @@ cpm_pcie2: pcie@f2640000 {
 				/* non-prefetchable memory */
 				0x82000000 0 0xf8000000 0  0xf8000000 0 0xf00000>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cpm_icu 0 ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map = <0 0 0 0 &cpm_icu ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
 			interrupts = <ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
 
 			num-lanes = <1>;

arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi

@@ -335,7 +335,7 @@ cps_pcie0: pcie@f4600000 {
 				/* non-prefetchable memory */
 				0x82000000 0 0xfa000000 0  0xfa000000 0 0xf00000>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cps_icu 0 ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map = <0 0 0 0 &cps_icu ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
 			interrupts = <ICU_GRP_NSR 22 IRQ_TYPE_LEVEL_HIGH>;
 			num-lanes = <1>;
 			clocks = <&cps_clk 1 13>;
@@ -361,7 +361,7 @@ cps_pcie1: pcie@f4620000 {
 				/* non-prefetchable memory */
 				0x82000000 0 0xfb000000 0  0xfb000000 0 0xf00000>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cps_icu 0 ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map = <0 0 0 0 &cps_icu ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
 			interrupts = <ICU_GRP_NSR 24 IRQ_TYPE_LEVEL_HIGH>;
 
 			num-lanes = <1>;
@@ -388,7 +388,7 @@ cps_pcie2: pcie@f4640000 {
 				/* non-prefetchable memory */
 				0x82000000 0 0xfc000000 0  0xfc000000 0 0xf00000>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &cps_icu 0 ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map = <0 0 0 0 &cps_icu ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
 			interrupts = <ICU_GRP_NSR 23 IRQ_TYPE_LEVEL_HIGH>;
 
 			num-lanes = <1>;

arch/arm64/boot/dts/renesas/salvator-common.dtsi

@@ -62,6 +62,7 @@ backlight: backlight {
 		brightness-levels = <256 128 64 16 8 4 0>;
 		default-brightness-level = <6>;
 
+		power-supply = <&reg_12v>;
 		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
 	};
 
@@ -83,6 +84,15 @@ reg_3p3v: regulator1 {
 		regulator-always-on;
 	};
 
+	reg_12v: regulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	rsnd_ak4613: sound {
 		compatible = "simple-audio-card";
 

arch/arm64/boot/dts/rockchip/rk3328.dtsi

@@ -582,7 +582,7 @@ rkvdec_mmu: iommu@ff360480 {
 	vop_mmu: iommu@ff373f00 {
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff373f00 0x0 0x100>;
-		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "vop_mmu";
 		#iommu-cells = <0>;
 		status = "disabled";

arch/arm64/boot/dts/rockchip/rk3368.dtsi

@@ -740,7 +740,7 @@ i2s_8ch: i2s-8ch@ff898000 {
 	iep_mmu: iommu@ff900800 {
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff900800 0x0 0x100>;
-		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH 0>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "iep_mmu";
 		#iommu-cells = <0>;
 		status = "disabled";

arch/arm64/boot/dts/rockchip/rk3399-firefly.dts

@@ -371,10 +371,10 @@ vcc_sdio: LDO_REG4 {
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-max-microvolt = <3000000>;
 				regulator-state-mem {
 					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <3300000>;
+					regulator-suspend-microvolt = <3000000>;
 				};
 			};
 

arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi

@@ -325,12 +325,12 @@ regulator-state-mem {
 			vcc_sd: LDO_REG4 {
 				regulator-name = "vcc_sd";
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-max-microvolt = <3000000>;
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-state-mem {
 					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <3300000>;
+					regulator-suspend-microvolt = <3000000>;
 				};
 			};
 

arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi

@@ -315,10 +315,10 @@ vcc_sdio: LDO_REG4 {
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-max-microvolt = <3000000>;
 				regulator-state-mem {
 					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <3300000>;
+					regulator-suspend-microvolt = <3000000>;
 				};
 			};
 

drivers/bus/mvebu-mbus.c

@@ -720,7 +720,7 @@ mvebu_mbus_default_setup_cpu_target(struct mvebu_mbus_state *mbus)
 			if (mbus->hw_io_coherency)
 				w->mbus_attr |= ATTR_HW_COHERENCY;
 			w->base = base & DDR_BASE_CS_LOW_MASK;
-			w->size = (size | ~DDR_SIZE_MASK) + 1;
+			w->size = (u64)(size | ~DDR_SIZE_MASK) + 1;
 		}
 	}
 	mvebu_mbus_dram_info.num_cs = cs;

drivers/reset/reset-socfpga.c

@@ -40,8 +40,9 @@ static int socfpga_reset_assert(struct reset_controller_dev *rcdev,
 	struct socfpga_reset_data *data = container_of(rcdev,
 						     struct socfpga_reset_data,
 						     rcdev);
-	int bank = id / BITS_PER_LONG;
-	int offset = id % BITS_PER_LONG;
+	int reg_width = sizeof(u32);
+	int bank = id / (reg_width * BITS_PER_BYTE);
+	int offset = id % (reg_width * BITS_PER_BYTE);
 	unsigned long flags;
 	u32 reg;
 
@@ -61,8 +62,9 @@ static int socfpga_reset_deassert(struct reset_controller_dev *rcdev,
 						     struct socfpga_reset_data,
 						     rcdev);
 
-	int bank = id / BITS_PER_LONG;
-	int offset = id % BITS_PER_LONG;
+	int reg_width = sizeof(u32);
+	int bank = id / (reg_width * BITS_PER_BYTE);
+	int offset = id % (reg_width * BITS_PER_BYTE);
 	unsigned long flags;
 	u32 reg;
 
@@ -81,8 +83,9 @@ static int socfpga_reset_status(struct reset_controller_dev *rcdev,
 {
 	struct socfpga_reset_data *data = container_of(rcdev,
 						struct socfpga_reset_data, rcdev);
-	int bank = id / BITS_PER_LONG;
-	int offset = id % BITS_PER_LONG;
+	int reg_width = sizeof(u32);
+	int bank = id / (reg_width * BITS_PER_BYTE);
+	int offset = id % (reg_width * BITS_PER_BYTE);
 	u32 reg;
 
 	reg = readl(data->membase + (bank * BANK_INCREMENT));
@@ -132,7 +135,7 @@ static int socfpga_reset_probe(struct platform_device *pdev)
 	spin_lock_init(&data->lock);
 
 	data->rcdev.owner = THIS_MODULE;
-	data->rcdev.nr_resets = NR_BANKS * BITS_PER_LONG;
+	data->rcdev.nr_resets = NR_BANKS * (sizeof(u32) * BITS_PER_BYTE);
 	data->rcdev.ops = &socfpga_reset_ops;
 	data->rcdev.of_node = pdev->dev.of_node;
 

include/linux/mbus.h

@@ -31,8 +31,8 @@ struct mbus_dram_target_info
 	struct mbus_dram_window {
 		u8	cs_index;
 		u8	mbus_attr;
-		u32	base;
-		u32	size;
+		u64	base;
+		u64	size;
 	} cs[4];
 };