Merge branch 'amd-xgbe-next'

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2015-05-12

The following series of patches includes functional updates and changes
to the driver.

- Add additional statistics to be collected and reported
- Use the netif_* functions for issuing some debug and informational
  driver messages
- Rx path SKB allocation cleanup/simplification
- Remove stand-alone phylib driver and incorporate function into the nic
  driver
- Simplify device tree support while maintaining backwards compatibility
- Fix the flow control negotiation logic to properly configure flow
  control
- Remove the checking and setting of the device dma_mask field

This patch series is based on net-next.

Changes in v2:
- Change from using the netif_msg_*/netdev_* combination for issuing
  messages to the more concise netif_*
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/amd-xgbe-phy.txt

-* AMD 10GbE PHY driver (amd-xgbe-phy)
-
-Required properties:
-- compatible: Should be "amd,xgbe-phy-seattle-v1a" and
-  "ethernet-phy-ieee802.3-c45"
-- reg: Address and length of the register sets for the device
-   - SerDes Rx/Tx registers
-   - SerDes integration registers (1/2)
-   - SerDes integration registers (2/2)
-- interrupt-parent: Should be the phandle for the interrupt controller
-  that services interrupts for this device
-- interrupts: Should contain the amd-xgbe-phy interrupt.
-
-Optional properties:
-- amd,speed-set: Speed capabilities of the device
-    0 - 1GbE and 10GbE (default)
-    1 - 2.5GbE and 10GbE
-
-The following optional properties are represented by an array with each
-value corresponding to a particular speed. The first array value represents
-the setting for the 1GbE speed, the second value for the 2.5GbE speed and
-the third value for the 10GbE speed.  All three values are required if the
-property is used.
-- amd,serdes-blwc: Baseline wandering correction enablement
-    0 - Off
-    1 - On
-- amd,serdes-cdr-rate: CDR rate speed selection
-- amd,serdes-pq-skew: PQ (data sampling) skew
-- amd,serdes-tx-amp: TX amplitude boost
-- amd,serdes-dfe-tap-config: DFE taps available to run
-- amd,serdes-dfe-tap-enable: DFE taps to enable
-
-Example:
-	xgbe_phy@e1240800 {
-		compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45";
-		reg = <0 0xe1240800 0 0x00400>,
-		      <0 0xe1250000 0 0x00060>,
-		      <0 0xe1250080 0 0x00004>;
-		interrupt-parent = <&gic>;
-		interrupts = <0 323 4>;
-		amd,speed-set = <0>;
-		amd,serdes-blwc = <1>, <1>, <0>;
-		amd,serdes-cdr-rate = <2>, <2>, <7>;
-		amd,serdes-pq-skew = <10>, <10>, <30>;
-		amd,serdes-tx-amp = <15>, <15>, <10>;
-		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
-		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
-	};

Documentation/devicetree/bindings/net/amd-xgbe.txt

@@ -5,12 +5,16 @@ Required properties:
 - reg: Address and length of the register sets for the device
    - MAC registers
    - PCS registers
+   - SerDes Rx/Tx registers
+   - SerDes integration registers (1/2)
+   - SerDes integration registers (2/2)
 - interrupt-parent: Should be the phandle for the interrupt controller
   that services interrupts for this device
 - interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt
   listed is required and is the general device interrupt. If the optional
   amd,per-channel-interrupt property is specified, then one additional
-  interrupt for each DMA channel supported by the device should be specified
+  interrupt for each DMA channel supported by the device should be specified.
+  The last interrupt listed should be the PCS auto-negotiation interrupt.
 - clocks:
    - DMA clock for the amd-xgbe device (used for calculating the
      correct Rx interrupt watchdog timer value on a DMA channel
@@ -19,7 +23,6 @@ Required properties:
 - clock-names: Should be the names of the clocks
    - "dma_clk" for the DMA clock
    - "ptp_clk" for the PTP clock
-- phy-handle: See ethernet.txt file in the same directory
 - phy-mode: See ethernet.txt file in the same directory
 
 Optional properties:
@@ -29,19 +32,46 @@ Optional properties:
 - amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate
   a unique interrupt for each DMA channel - this requires an additional
   interrupt be configured for each DMA channel
+- amd,speed-set: Speed capabilities of the device
+    0 - 1GbE and 10GbE (default)
+    1 - 2.5GbE and 10GbE
+
+The following optional properties are represented by an array with each
+value corresponding to a particular speed. The first array value represents
+the setting for the 1GbE speed, the second value for the 2.5GbE speed and
+the third value for the 10GbE speed.  All three values are required if the
+property is used.
+- amd,serdes-blwc: Baseline wandering correction enablement
+    0 - Off
+    1 - On
+- amd,serdes-cdr-rate: CDR rate speed selection
+- amd,serdes-pq-skew: PQ (data sampling) skew
+- amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
 
 Example:
 	xgbe@e0700000 {
 		compatible = "amd,xgbe-seattle-v1a";
 		reg = <0 0xe0700000 0 0x80000>,
-		      <0 0xe0780000 0 0x80000>;
+		      <0 0xe0780000 0 0x80000>,
+		      <0 0xe1240800 0 0x00400>,
+		      <0 0xe1250000 0 0x00060>,
+		      <0 0xe1250080 0 0x00004>;
 		interrupt-parent = <&gic>;
 		interrupts = <0 325 4>,
-			     <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>;
+			     <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>,
+			     <0 323 4>;
 		amd,per-channel-interrupt;
 		clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>;
 		clock-names = "dma_clk", "ptp_clk";
-		phy-handle = <&phy>;
 		phy-mode = "xgmii";
 		mac-address = [ 02 a1 a2 a3 a4 a5 ];
+		amd,speed-set = <0>;
+		amd,serdes-blwc = <1>, <1>, <0>;
+		amd,serdes-cdr-rate = <2>, <2>, <7>;
+		amd,serdes-pq-skew = <10>, <10>, <30>;
+		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
 	};

MAINTAINERS

@@ -652,7 +652,6 @@ M:	Tom Lendacky <thomas.lendacky@amd.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/amd/xgbe/
-F:	drivers/net/phy/amd-xgbe-phy.c
 
 AMS (Apple Motion Sensor) DRIVER
 M:	Michael Hanselmann <linux-kernel@hansmi.ch>

drivers/net/ethernet/amd/Kconfig

@@ -179,10 +179,8 @@ config SUNLANCE
 
 config AMD_XGBE
 	tristate "AMD 10GbE Ethernet driver"
-	depends on (OF_NET || ACPI) && HAS_IOMEM && HAS_DMA
+	depends on ((OF_NET && OF_ADDRESS) || ACPI) && HAS_IOMEM && HAS_DMA
 	depends on ARM64 || COMPILE_TEST
-	select PHYLIB
-	select AMD_XGBE_PHY
 	select BITREVERSE
 	select CRC32
 	select PTP_1588_CLOCK

drivers/net/ethernet/amd/xgbe/xgbe-common.h

@@ -857,6 +857,48 @@
  */
 #define PCS_MMD_SELECT			0xff
 
+/* SerDes integration register offsets */
+#define SIR0_KR_RT_1			0x002c
+#define SIR0_STATUS			0x0040
+#define SIR1_SPEED			0x0000
+
+/* SerDes integration register entry bit positions and sizes */
+#define SIR0_KR_RT_1_RESET_INDEX	11
+#define SIR0_KR_RT_1_RESET_WIDTH	1
+#define SIR0_STATUS_RX_READY_INDEX	0
+#define SIR0_STATUS_RX_READY_WIDTH	1
+#define SIR0_STATUS_TX_READY_INDEX	8
+#define SIR0_STATUS_TX_READY_WIDTH	1
+#define SIR1_SPEED_CDR_RATE_INDEX	12
+#define SIR1_SPEED_CDR_RATE_WIDTH	4
+#define SIR1_SPEED_DATARATE_INDEX	4
+#define SIR1_SPEED_DATARATE_WIDTH	2
+#define SIR1_SPEED_PLLSEL_INDEX		3
+#define SIR1_SPEED_PLLSEL_WIDTH		1
+#define SIR1_SPEED_RATECHANGE_INDEX	6
+#define SIR1_SPEED_RATECHANGE_WIDTH	1
+#define SIR1_SPEED_TXAMP_INDEX		8
+#define SIR1_SPEED_TXAMP_WIDTH		4
+#define SIR1_SPEED_WORDMODE_INDEX	0
+#define SIR1_SPEED_WORDMODE_WIDTH	3
+
+/* SerDes RxTx register offsets */
+#define RXTX_REG6			0x0018
+#define RXTX_REG20			0x0050
+#define RXTX_REG22			0x0058
+#define RXTX_REG114			0x01c8
+#define RXTX_REG129			0x0204
+
+/* SerDes RxTx register entry bit positions and sizes */
+#define RXTX_REG6_RESETB_RXD_INDEX	8
+#define RXTX_REG6_RESETB_RXD_WIDTH	1
+#define RXTX_REG20_BLWC_ENA_INDEX	2
+#define RXTX_REG20_BLWC_ENA_WIDTH	1
+#define RXTX_REG114_PQ_REG_INDEX	9
+#define RXTX_REG114_PQ_REG_WIDTH	7
+#define RXTX_REG129_RXDFE_CONFIG_INDEX	14
+#define RXTX_REG129_RXDFE_CONFIG_WIDTH	2
+
 /* Descriptor/Packet entry bit positions and sizes */
 #define RX_PACKET_ERRORS_CRC_INDEX		2
 #define RX_PACKET_ERRORS_CRC_WIDTH		1
@@ -973,10 +1015,47 @@
 #define TX_NORMAL_DESC2_VLAN_INSERT		0x2
 
 /* MDIO undefined or vendor specific registers */
+#ifndef MDIO_PMA_10GBR_PMD_CTRL
+#define MDIO_PMA_10GBR_PMD_CTRL		0x0096
+#endif
+
+#ifndef MDIO_PMA_10GBR_FECCTRL
+#define MDIO_PMA_10GBR_FECCTRL		0x00ab
+#endif
+
+#ifndef MDIO_AN_XNP
+#define MDIO_AN_XNP			0x0016
+#endif
+
+#ifndef MDIO_AN_LPX
+#define MDIO_AN_LPX			0x0019
+#endif
+
 #ifndef MDIO_AN_COMP_STAT
 #define MDIO_AN_COMP_STAT		0x0030
 #endif
 
+#ifndef MDIO_AN_INTMASK
+#define MDIO_AN_INTMASK			0x8001
+#endif
+
+#ifndef MDIO_AN_INT
+#define MDIO_AN_INT			0x8002
+#endif
+
+#ifndef MDIO_CTRL1_SPEED1G
+#define MDIO_CTRL1_SPEED1G		(MDIO_CTRL1_SPEED10G & ~BMCR_SPEED100)
+#endif
+
+/* MDIO mask values */
+#define XGBE_XNP_MCF_NULL_MESSAGE	0x001
+#define XGBE_XNP_ACK_PROCESSED		BIT(12)
+#define XGBE_XNP_MP_FORMATTED		BIT(13)
+#define XGBE_XNP_NP_EXCHANGE		BIT(15)
+
+#define XGBE_KR_TRAINING_START		BIT(0)
+#define XGBE_KR_TRAINING_ENABLE		BIT(1)
+
 /* Bit setting and getting macros
  *  The get macro will extract the current bit field value from within
  *  the variable
@@ -1118,6 +1197,82 @@ do {									\
 #define XPCS_IOREAD(_pdata, _off)					\
 	ioread32((_pdata)->xpcs_regs + (_off))
 
+/* Macros for building, reading or writing register values or bits
+ * within the register values of SerDes integration registers.
+ */
+#define XSIR_GET_BITS(_var, _prefix, _field)                            \
+	GET_BITS((_var),                                                \
+		 _prefix##_##_field##_INDEX,                            \
+		 _prefix##_##_field##_WIDTH)
+
+#define XSIR_SET_BITS(_var, _prefix, _field, _val)                      \
+	SET_BITS((_var),                                                \
+		 _prefix##_##_field##_INDEX,                            \
+		 _prefix##_##_field##_WIDTH, (_val))
+
+#define XSIR0_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->sir0_regs + _reg)
+
+#define XSIR0_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XSIR0_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XSIR0_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->sir0_regs + _reg)
+
+#define XSIR0_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XSIR0_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XSIR0_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
+#define XSIR1_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->sir1_regs + _reg)
+
+#define XSIR1_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XSIR1_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XSIR1_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->sir1_regs + _reg)
+
+#define XSIR1_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XSIR1_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XSIR1_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
+/* Macros for building, reading or writing register values or bits
+ * within the register values of SerDes RxTx registers.
+ */
+#define XRXTX_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->rxtx_regs + _reg)
+
+#define XRXTX_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XRXTX_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XRXTX_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->rxtx_regs + _reg)
+
+#define XRXTX_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XRXTX_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XRXTX_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
 /* Macros for building, reading or writing register values or bits
  * using MDIO.  Different from above because of the use of standardized
  * Linux include values.  No shifting is performed with the bit

drivers/net/ethernet/amd/xgbe/xgbe-dcb.c

@@ -150,9 +150,12 @@ static int xgbe_dcb_ieee_setets(struct net_device *netdev,
 	tc_ets = 0;
 	tc_ets_weight = 0;
 	for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
-		DBGPR("  TC%u: tx_bw=%hhu, rx_bw=%hhu, tsa=%hhu\n", i,
-		      ets->tc_tx_bw[i], ets->tc_rx_bw[i], ets->tc_tsa[i]);
-		DBGPR("  PRIO%u: TC=%hhu\n", i, ets->prio_tc[i]);
+		netif_dbg(pdata, drv, netdev,
+			  "TC%u: tx_bw=%hhu, rx_bw=%hhu, tsa=%hhu\n", i,
+			  ets->tc_tx_bw[i], ets->tc_rx_bw[i],
+			  ets->tc_tsa[i]);
+		netif_dbg(pdata, drv, netdev, "PRIO%u: TC=%hhu\n", i,
+			  ets->prio_tc[i]);
 
 		if ((ets->tc_tx_bw[i] || ets->tc_tsa[i]) &&
 		    (i >= pdata->hw_feat.tc_cnt))
@@ -214,8 +217,9 @@ static int xgbe_dcb_ieee_setpfc(struct net_device *netdev,
 {
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
 
-	DBGPR("  cap=%hhu, en=%hhx, mbc=%hhu, delay=%hhu\n",
-	      pfc->pfc_cap, pfc->pfc_en, pfc->mbc, pfc->delay);
+	netif_dbg(pdata, drv, netdev,
+		  "cap=%hhu, en=%#hhx, mbc=%hhu, delay=%hhu\n",
+		  pfc->pfc_cap, pfc->pfc_en, pfc->mbc, pfc->delay);
 
 	if (!pdata->pfc) {
 		pdata->pfc = devm_kzalloc(pdata->dev, sizeof(*pdata->pfc),
@@ -238,9 +242,10 @@ static u8 xgbe_dcb_getdcbx(struct net_device *netdev)
 
 static u8 xgbe_dcb_setdcbx(struct net_device *netdev, u8 dcbx)
 {
+	struct xgbe_prv_data *pdata = netdev_priv(netdev);
 	u8 support = xgbe_dcb_getdcbx(netdev);
 
-	DBGPR("  DCBX=%#hhx\n", dcbx);
+	netif_dbg(pdata, drv, netdev, "DCBX=%#hhx\n", dcbx);
 
 	if (dcbx & ~support)
 		return 1;

drivers/net/ethernet/amd/xgbe/xgbe-desc.c

@@ -208,8 +208,9 @@ static int xgbe_init_ring(struct xgbe_prv_data *pdata,
 	if (!ring->rdata)
 		return -ENOMEM;
 
-	DBGPR("    rdesc=0x%p, rdesc_dma=0x%llx, rdata=0x%p\n",
-	      ring->rdesc, ring->rdesc_dma, ring->rdata);
+	netif_dbg(pdata, drv, pdata->netdev,
+		  "rdesc=%p, rdesc_dma=%pad, rdata=%p\n",
+		  ring->rdesc, &ring->rdesc_dma, ring->rdata);
 
 	DBGPR("<--xgbe_init_ring\n");
 
@@ -226,7 +227,9 @@ static int xgbe_alloc_ring_resources(struct xgbe_prv_data *pdata)
 
 	channel = pdata->channel;
 	for (i = 0; i < pdata->channel_count; i++, channel++) {
-		DBGPR("  %s - tx_ring:\n", channel->name);
+		netif_dbg(pdata, drv, pdata->netdev, "%s - Tx ring:\n",
+			  channel->name);
+
 		ret = xgbe_init_ring(pdata, channel->tx_ring,
 				     pdata->tx_desc_count);
 		if (ret) {
@@ -235,12 +238,14 @@ static int xgbe_alloc_ring_resources(struct xgbe_prv_data *pdata)
 			goto err_ring;
 		}
 
-		DBGPR("  %s - rx_ring:\n", channel->name);
+		netif_dbg(pdata, drv, pdata->netdev, "%s - Rx ring:\n",
+			  channel->name);
+
 		ret = xgbe_init_ring(pdata, channel->rx_ring,
 				     pdata->rx_desc_count);
 		if (ret) {
 			netdev_alert(pdata->netdev,
-				     "error initializing Tx ring\n");
+				     "error initializing Rx ring\n");
 			goto err_ring;
 		}
 	}
@@ -476,8 +481,6 @@ static void xgbe_unmap_rdata(struct xgbe_prv_data *pdata,
 
 	if (rdata->state_saved) {
 		rdata->state_saved = 0;
-		rdata->state.incomplete = 0;
-		rdata->state.context_next = 0;
 		rdata->state.skb = NULL;
 		rdata->state.len = 0;
 		rdata->state.error = 0;
@@ -518,8 +521,6 @@ static int xgbe_map_tx_skb(struct xgbe_channel *channel, struct sk_buff *skb)
 	rdata = XGBE_GET_DESC_DATA(ring, cur_index);
 
 	if (tso) {
-		DBGPR("  TSO packet\n");
-
 		/* Map the TSO header */
 		skb_dma = dma_map_single(pdata->dev, skb->data,
 					 packet->header_len, DMA_TO_DEVICE);
@@ -529,6 +530,9 @@ static int xgbe_map_tx_skb(struct xgbe_channel *channel, struct sk_buff *skb)
 		}
 		rdata->skb_dma = skb_dma;
 		rdata->skb_dma_len = packet->header_len;
+		netif_dbg(pdata, tx_queued, pdata->netdev,
+			  "skb header: index=%u, dma=%pad, len=%u\n",
+			  cur_index, &skb_dma, packet->header_len);
 
 		offset = packet->header_len;
 
@@ -550,8 +554,9 @@ static int xgbe_map_tx_skb(struct xgbe_channel *channel, struct sk_buff *skb)
 		}
 		rdata->skb_dma = skb_dma;
 		rdata->skb_dma_len = len;
-		DBGPR("  skb data: index=%u, dma=0x%llx, len=%u\n",
-		      cur_index, skb_dma, len);
+		netif_dbg(pdata, tx_queued, pdata->netdev,
+			  "skb data: index=%u, dma=%pad, len=%u\n",
+			  cur_index, &skb_dma, len);
 
 		datalen -= len;
 		offset += len;
@@ -563,7 +568,8 @@ static int xgbe_map_tx_skb(struct xgbe_channel *channel, struct sk_buff *skb)
 	}
 
 	for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
-		DBGPR("  mapping frag %u\n", i);
+		netif_dbg(pdata, tx_queued, pdata->netdev,
+			  "mapping frag %u\n", i);
 
 		frag = &skb_shinfo(skb)->frags[i];
 		offset = 0;
@@ -582,8 +588,9 @@ static int xgbe_map_tx_skb(struct xgbe_channel *channel, struct sk_buff *skb)
 			rdata->skb_dma = skb_dma;
 			rdata->skb_dma_len = len;
 			rdata->mapped_as_page = 1;
-			DBGPR("  skb data: index=%u, dma=0x%llx, len=%u\n",
-			      cur_index, skb_dma, len);
+			netif_dbg(pdata, tx_queued, pdata->netdev,
+				  "skb frag: index=%u, dma=%pad, len=%u\n",
+				  cur_index, &skb_dma, len);
 
 			datalen -= len;
 			offset += len;

drivers/net/ethernet/amd/xgbe/xgbe-dev.c

@@ -710,7 +710,8 @@ static int xgbe_set_promiscuous_mode(struct xgbe_prv_data *pdata,
 	if (XGMAC_IOREAD_BITS(pdata, MAC_PFR, PR) == val)
 		return 0;
 
-	DBGPR("  %s promiscuous mode\n", enable ? "entering" : "leaving");
+	netif_dbg(pdata, drv, pdata->netdev, "%s promiscuous mode\n",
+		  enable ? "entering" : "leaving");
 	XGMAC_IOWRITE_BITS(pdata, MAC_PFR, PR, val);
 
 	return 0;
@@ -724,7 +725,8 @@ static int xgbe_set_all_multicast_mode(struct xgbe_prv_data *pdata,
 	if (XGMAC_IOREAD_BITS(pdata, MAC_PFR, PM) == val)
 		return 0;
 
-	DBGPR("  %s allmulti mode\n", enable ? "entering" : "leaving");
+	netif_dbg(pdata, drv, pdata->netdev, "%s allmulti mode\n",
+		  enable ? "entering" : "leaving");
 	XGMAC_IOWRITE_BITS(pdata, MAC_PFR, PM, val);
 
 	return 0;
@@ -749,8 +751,9 @@ static void xgbe_set_mac_reg(struct xgbe_prv_data *pdata,
 		mac_addr[0] = ha->addr[4];
 		mac_addr[1] = ha->addr[5];
 
-		DBGPR("  adding mac address %pM at 0x%04x\n", ha->addr,
-		      *mac_reg);
+		netif_dbg(pdata, drv, pdata->netdev,
+			  "adding mac address %pM at %#x\n",
+			  ha->addr, *mac_reg);
 
 		XGMAC_SET_BITS(mac_addr_hi, MAC_MACA1HR, AE, 1);
 	}
@@ -907,23 +910,6 @@ static void xgbe_write_mmd_regs(struct xgbe_prv_data *pdata, int prtad,
 	else
 		mmd_address = (pdata->mdio_mmd << 16) | (mmd_reg & 0xffff);
 
-	/* If the PCS is changing modes, match the MAC speed to it */
-	if (((mmd_address >> 16) == MDIO_MMD_PCS) &&
-	    ((mmd_address & 0xffff) == MDIO_CTRL2)) {
-		struct phy_device *phydev = pdata->phydev;
-
-		if (mmd_data & MDIO_PCS_CTRL2_TYPE) {
-			/* KX mode */
-			if (phydev->supported & SUPPORTED_1000baseKX_Full)
-				xgbe_set_gmii_speed(pdata);
-			else
-				xgbe_set_gmii_2500_speed(pdata);
-		} else {
-			/* KR mode */
-			xgbe_set_xgmii_speed(pdata);
-		}
-	}
-
 	/* The PCS registers are accessed using mmio. The underlying APB3
 	 * management interface uses indirect addressing to access the MMD
 	 * register sets. This requires accessing of the PCS register in two
@@ -1322,7 +1308,8 @@ static void xgbe_config_dcb_tc(struct xgbe_prv_data *pdata)
 	for (i = 0; i < pdata->hw_feat.tc_cnt; i++) {
 		switch (ets->tc_tsa[i]) {
 		case IEEE_8021QAZ_TSA_STRICT:
-			DBGPR("  TC%u using SP\n", i);
+			netif_dbg(pdata, drv, pdata->netdev,
+				  "TC%u using SP\n", i);
 			XGMAC_MTL_IOWRITE_BITS(pdata, i, MTL_TC_ETSCR, TSA,
 					       MTL_TSA_SP);
 			break;
@@ -1330,7 +1317,8 @@ static void xgbe_config_dcb_tc(struct xgbe_prv_data *pdata)
 			weight = total_weight * ets->tc_tx_bw[i] / 100;
 			weight = clamp(weight, min_weight, total_weight);
 
-			DBGPR("  TC%u using DWRR (weight %u)\n", i, weight);
+			netif_dbg(pdata, drv, pdata->netdev,
+				  "TC%u using DWRR (weight %u)\n", i, weight);
 			XGMAC_MTL_IOWRITE_BITS(pdata, i, MTL_TC_ETSCR, TSA,
 					       MTL_TSA_ETS);
 			XGMAC_MTL_IOWRITE_BITS(pdata, i, MTL_TC_QWR, QW,
@@ -1359,7 +1347,8 @@ static void xgbe_config_dcb_pfc(struct xgbe_prv_data *pdata)
 		}
 		mask &= 0xff;
 
-		DBGPR("  TC%u PFC mask=%#x\n", tc, mask);
+		netif_dbg(pdata, drv, pdata->netdev, "TC%u PFC mask=%#x\n",
+			  tc, mask);
 		reg = MTL_TCPM0R + (MTL_TCPM_INC * (tc / MTL_TCPM_TC_PER_REG));
 		reg_val = XGMAC_IOREAD(pdata, reg);
 
@@ -1457,8 +1446,9 @@ static void xgbe_dev_xmit(struct xgbe_channel *channel)
 	/* Create a context descriptor if this is a TSO packet */
 	if (tso_context || vlan_context) {
 		if (tso_context) {
-			DBGPR("  TSO context descriptor, mss=%u\n",
-			      packet->mss);
+			netif_dbg(pdata, tx_queued, pdata->netdev,
+				  "TSO context descriptor, mss=%u\n",
+				  packet->mss);
 
 			/* Set the MSS size */
 			XGMAC_SET_BITS_LE(rdesc->desc2, TX_CONTEXT_DESC2,
@@ -1476,8 +1466,9 @@ static void xgbe_dev_xmit(struct xgbe_channel *channel)
 		}
 
 		if (vlan_context) {
-			DBGPR("  VLAN context descriptor, ctag=%u\n",
-			      packet->vlan_ctag);
+			netif_dbg(pdata, tx_queued, pdata->netdev,
+				  "VLAN context descriptor, ctag=%u\n",
+				  packet->vlan_ctag);
 
 			/* Mark it as a CONTEXT descriptor */
 			XGMAC_SET_BITS_LE(rdesc->desc3, TX_CONTEXT_DESC3,
@@ -1533,6 +1524,8 @@ static void xgbe_dev_xmit(struct xgbe_channel *channel)
 				  packet->tcp_payload_len);
 		XGMAC_SET_BITS_LE(rdesc->desc3, TX_NORMAL_DESC3, TCPHDRLEN,
 				  packet->tcp_header_len / 4);
+
+		pdata->ext_stats.tx_tso_packets++;
 	} else {
 		/* Enable CRC and Pad Insertion */
 		XGMAC_SET_BITS_LE(rdesc->desc3, TX_NORMAL_DESC3, CPC, 0);
@@ -1594,9 +1587,9 @@ static void xgbe_dev_xmit(struct xgbe_channel *channel)
 	rdesc = rdata->rdesc;
 	XGMAC_SET_BITS_LE(rdesc->desc3, TX_NORMAL_DESC3, OWN, 1);
 
-#ifdef XGMAC_ENABLE_TX_DESC_DUMP
-	xgbe_dump_tx_desc(ring, start_index, packet->rdesc_count, 1);
-#endif
+	if (netif_msg_tx_queued(pdata))
+		xgbe_dump_tx_desc(pdata, ring, start_index,
+				  packet->rdesc_count, 1);
 
 	/* Make sure ownership is written to the descriptor */
 	dma_wmb();
@@ -1618,11 +1611,12 @@ static void xgbe_dev_xmit(struct xgbe_channel *channel)
 
 static int xgbe_dev_read(struct xgbe_channel *channel)
 {
+	struct xgbe_prv_data *pdata = channel->pdata;
 	struct xgbe_ring *ring = channel->rx_ring;
 	struct xgbe_ring_data *rdata;
 	struct xgbe_ring_desc *rdesc;
 	struct xgbe_packet_data *packet = &ring->packet_data;
-	struct net_device *netdev = channel->pdata->netdev;
+	struct net_device *netdev = pdata->netdev;
 	unsigned int err, etlt, l34t;
 
 	DBGPR("-->xgbe_dev_read: cur = %d\n", ring->cur);
@@ -1637,9 +1631,8 @@ static int xgbe_dev_read(struct xgbe_channel *channel)
 	/* Make sure descriptor fields are read after reading the OWN bit */
 	dma_rmb();
 
-#ifdef XGMAC_ENABLE_RX_DESC_DUMP
-	xgbe_dump_rx_desc(ring, rdesc, ring->cur);
-#endif
+	if (netif_msg_rx_status(pdata))
+		xgbe_dump_rx_desc(pdata, ring, ring->cur);
 
 	if (XGMAC_GET_BITS_LE(rdesc->desc3, RX_NORMAL_DESC3, CTXT)) {
 		/* Timestamp Context Descriptor */
@@ -1661,9 +1654,12 @@ static int xgbe_dev_read(struct xgbe_channel *channel)
 			       CONTEXT_NEXT, 1);
 
 	/* Get the header length */
-	if (XGMAC_GET_BITS_LE(rdesc->desc3, RX_NORMAL_DESC3, FD))
+	if (XGMAC_GET_BITS_LE(rdesc->desc3, RX_NORMAL_DESC3, FD)) {
 		rdata->rx.hdr_len = XGMAC_GET_BITS_LE(rdesc->desc2,
 						      RX_NORMAL_DESC2, HL);
+		if (rdata->rx.hdr_len)
+			pdata->ext_stats.rx_split_header_packets++;
+	}
 
 	/* Get the RSS hash */
 	if (XGMAC_GET_BITS_LE(rdesc->desc3, RX_NORMAL_DESC3, RSV)) {
@@ -1700,14 +1696,14 @@ static int xgbe_dev_read(struct xgbe_channel *channel)
 		       INCOMPLETE, 0);
 
 	/* Set checksum done indicator as appropriate */
-	if (channel->pdata->netdev->features & NETIF_F_RXCSUM)
+	if (netdev->features & NETIF_F_RXCSUM)
 		XGMAC_SET_BITS(packet->attributes, RX_PACKET_ATTRIBUTES,
 			       CSUM_DONE, 1);
 
 	/* Check for errors (only valid in last descriptor) */
 	err = XGMAC_GET_BITS_LE(rdesc->desc3, RX_NORMAL_DESC3, ES);
 	etlt = XGMAC_GET_BITS_LE(rdesc->desc3, RX_NORMAL_DESC3, ETLT);
-	DBGPR("  err=%u, etlt=%#x\n", err, etlt);
+	netif_dbg(pdata, rx_status, netdev, "err=%u, etlt=%#x\n", err, etlt);
 
 	if (!err || !etlt) {
 		/* No error if err is 0 or etlt is 0 */
@@ -1718,7 +1714,8 @@ static int xgbe_dev_read(struct xgbe_channel *channel)
 			packet->vlan_ctag = XGMAC_GET_BITS_LE(rdesc->desc0,
 							      RX_NORMAL_DESC0,
 							      OVT);
-			DBGPR("  vlan-ctag=0x%04x\n", packet->vlan_ctag);
+			netif_dbg(pdata, rx_status, netdev, "vlan-ctag=%#06x\n",
+				  packet->vlan_ctag);
 		}
 	} else {
 		if ((etlt == 0x05) || (etlt == 0x06))
@@ -2026,9 +2023,9 @@ static void xgbe_config_tx_fifo_size(struct xgbe_prv_data *pdata)
 	for (i = 0; i < pdata->tx_q_count; i++)
 		XGMAC_MTL_IOWRITE_BITS(pdata, i, MTL_Q_TQOMR, TQS, fifo_size);
 
-	netdev_notice(pdata->netdev,
-		      "%d Tx hardware queues, %d byte fifo per queue\n",
-		      pdata->tx_q_count, ((fifo_size + 1) * 256));
+	netif_info(pdata, drv, pdata->netdev,
+		   "%d Tx hardware queues, %d byte fifo per queue\n",
+		   pdata->tx_q_count, ((fifo_size + 1) * 256));
 }
 
 static void xgbe_config_rx_fifo_size(struct xgbe_prv_data *pdata)
@@ -2042,9 +2039,9 @@ static void xgbe_config_rx_fifo_size(struct xgbe_prv_data *pdata)
 	for (i = 0; i < pdata->rx_q_count; i++)
 		XGMAC_MTL_IOWRITE_BITS(pdata, i, MTL_Q_RQOMR, RQS, fifo_size);
 
-	netdev_notice(pdata->netdev,
-		      "%d Rx hardware queues, %d byte fifo per queue\n",
-		      pdata->rx_q_count, ((fifo_size + 1) * 256));
+	netif_info(pdata, drv, pdata->netdev,
+		   "%d Rx hardware queues, %d byte fifo per queue\n",
+		   pdata->rx_q_count, ((fifo_size + 1) * 256));
 }
 
 static void xgbe_config_queue_mapping(struct xgbe_prv_data *pdata)
@@ -2063,14 +2060,16 @@ static void xgbe_config_queue_mapping(struct xgbe_prv_data *pdata)
 
 	for (i = 0, queue = 0; i < pdata->hw_feat.tc_cnt; i++) {
 		for (j = 0; j < qptc; j++) {
-			DBGPR("  TXq%u mapped to TC%u\n", queue, i);
+			netif_dbg(pdata, drv, pdata->netdev,
+				  "TXq%u mapped to TC%u\n", queue, i);
 			XGMAC_MTL_IOWRITE_BITS(pdata, queue, MTL_Q_TQOMR,
 					       Q2TCMAP, i);
 			pdata->q2tc_map[queue++] = i;
 		}
 
 		if (i < qptc_extra) {
-			DBGPR("  TXq%u mapped to TC%u\n", queue, i);
+			netif_dbg(pdata, drv, pdata->netdev,
+				  "TXq%u mapped to TC%u\n", queue, i);
 			XGMAC_MTL_IOWRITE_BITS(pdata, queue, MTL_Q_TQOMR,
 					       Q2TCMAP, i);
 			pdata->q2tc_map[queue++] = i;
@@ -2088,13 +2087,15 @@ static void xgbe_config_queue_mapping(struct xgbe_prv_data *pdata)
 	for (i = 0, prio = 0; i < prio_queues;) {
 		mask = 0;
 		for (j = 0; j < ppq; j++) {
-			DBGPR("  PRIO%u mapped to RXq%u\n", prio, i);
+			netif_dbg(pdata, drv, pdata->netdev,
+				  "PRIO%u mapped to RXq%u\n", prio, i);
 			mask |= (1 << prio);
 			pdata->prio2q_map[prio++] = i;
 		}
 
 		if (i < ppq_extra) {
-			DBGPR("  PRIO%u mapped to RXq%u\n", prio, i);
+			netif_dbg(pdata, drv, pdata->netdev,
+				  "PRIO%u mapped to RXq%u\n", prio, i);
 			mask |= (1 << prio);
 			pdata->prio2q_map[prio++] = i;
 		}

drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c

@@ -133,6 +133,12 @@ struct xgbe_stats {
 	  offsetof(struct xgbe_prv_data, mmc_stats._var),	\
 	}
 
+#define XGMAC_EXT_STAT(_string, _var)				\
+	{ _string,						\
+	  FIELD_SIZEOF(struct xgbe_ext_stats, _var),		\
+	  offsetof(struct xgbe_prv_data, ext_stats._var),	\
+	}
+
 static const struct xgbe_stats xgbe_gstring_stats[] = {
 	XGMAC_MMC_STAT("tx_bytes", txoctetcount_gb),
 	XGMAC_MMC_STAT("tx_packets", txframecount_gb),
@@ -140,6 +146,7 @@ static const struct xgbe_stats xgbe_gstring_stats[] = {
 	XGMAC_MMC_STAT("tx_broadcast_packets", txbroadcastframes_gb),
 	XGMAC_MMC_STAT("tx_multicast_packets", txmulticastframes_gb),
 	XGMAC_MMC_STAT("tx_vlan_packets", txvlanframes_g),
+	XGMAC_EXT_STAT("tx_tso_packets", tx_tso_packets),
 	XGMAC_MMC_STAT("tx_64_byte_packets", tx64octets_gb),
 	XGMAC_MMC_STAT("tx_65_to_127_byte_packets", tx65to127octets_gb),
 	XGMAC_MMC_STAT("tx_128_to_255_byte_packets", tx128to255octets_gb),
@@ -171,6 +178,7 @@ static const struct xgbe_stats xgbe_gstring_stats[] = {
 	XGMAC_MMC_STAT("rx_fifo_overflow_errors", rxfifooverflow),
 	XGMAC_MMC_STAT("rx_watchdog_errors", rxwatchdogerror),
 	XGMAC_MMC_STAT("rx_pause_frames", rxpauseframes),
+	XGMAC_EXT_STAT("rx_split_header_packets", rx_split_header_packets),
 };
 
 #define XGBE_STATS_COUNT	ARRAY_SIZE(xgbe_gstring_stats)
@@ -239,9 +247,9 @@ static void xgbe_get_pauseparam(struct net_device *netdev,
 
 	DBGPR("-->xgbe_get_pauseparam\n");
 
-	pause->autoneg = pdata->pause_autoneg;
-	pause->tx_pause = pdata->tx_pause;
-	pause->rx_pause = pdata->rx_pause;
+	pause->autoneg = pdata->phy.pause_autoneg;
+	pause->tx_pause = pdata->phy.tx_pause;
+	pause->rx_pause = pdata->phy.rx_pause;
 
 	DBGPR("<--xgbe_get_pauseparam\n");
 }
@@ -250,7 +258,6 @@ static int xgbe_set_pauseparam(struct net_device *netdev,
 			       struct ethtool_pauseparam *pause)
 {
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
-	struct phy_device *phydev = pdata->phydev;
 	int ret = 0;
 
 	DBGPR("-->xgbe_set_pauseparam\n");
@@ -258,21 +265,26 @@ static int xgbe_set_pauseparam(struct net_device *netdev,
 	DBGPR("  autoneg = %d, tx_pause = %d, rx_pause = %d\n",
 	      pause->autoneg, pause->tx_pause, pause->rx_pause);
 
-	pdata->pause_autoneg = pause->autoneg;
-	if (pause->autoneg) {
-		phydev->advertising |= ADVERTISED_Pause;
-		phydev->advertising |= ADVERTISED_Asym_Pause;
+	if (pause->autoneg && (pdata->phy.autoneg != AUTONEG_ENABLE))
+		return -EINVAL;
+
+	pdata->phy.pause_autoneg = pause->autoneg;
+	pdata->phy.tx_pause = pause->tx_pause;
+	pdata->phy.rx_pause = pause->rx_pause;
 
-	} else {
-		phydev->advertising &= ~ADVERTISED_Pause;
-		phydev->advertising &= ~ADVERTISED_Asym_Pause;
+	pdata->phy.advertising &= ~ADVERTISED_Pause;
+	pdata->phy.advertising &= ~ADVERTISED_Asym_Pause;
 
-		pdata->tx_pause = pause->tx_pause;
-		pdata->rx_pause = pause->rx_pause;
+	if (pause->rx_pause) {
+		pdata->phy.advertising |= ADVERTISED_Pause;
+		pdata->phy.advertising |= ADVERTISED_Asym_Pause;
 	}
 
+	if (pause->tx_pause)
+		pdata->phy.advertising ^= ADVERTISED_Asym_Pause;
+
 	if (netif_running(netdev))
-		ret = phy_start_aneg(phydev);
+		ret = pdata->phy_if.phy_config_aneg(pdata);
 
 	DBGPR("<--xgbe_set_pauseparam\n");
 
@@ -283,36 +295,39 @@ static int xgbe_get_settings(struct net_device *netdev,
 			     struct ethtool_cmd *cmd)
 {
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
-	int ret;
 
 	DBGPR("-->xgbe_get_settings\n");
 
-	if (!pdata->phydev)
-		return -ENODEV;
+	cmd->phy_address = pdata->phy.address;
+
+	cmd->supported = pdata->phy.supported;
+	cmd->advertising = pdata->phy.advertising;
+	cmd->lp_advertising = pdata->phy.lp_advertising;
+
+	cmd->autoneg = pdata->phy.autoneg;
+	ethtool_cmd_speed_set(cmd, pdata->phy.speed);
+	cmd->duplex = pdata->phy.duplex;
 
-	ret = phy_ethtool_gset(pdata->phydev, cmd);
+	cmd->port = PORT_NONE;
+	cmd->transceiver = XCVR_INTERNAL;
 
 	DBGPR("<--xgbe_get_settings\n");
 
-	return ret;
+	return 0;
 }
 
 static int xgbe_set_settings(struct net_device *netdev,
 			     struct ethtool_cmd *cmd)
 {
 	struct xgbe_prv_data *pdata = netdev_priv(netdev);
-	struct phy_device *phydev = pdata->phydev;
 	u32 speed;
 	int ret;
 
 	DBGPR("-->xgbe_set_settings\n");
 
-	if (!pdata->phydev)
-		return -ENODEV;
-
 	speed = ethtool_cmd_speed(cmd);
 
-	if (cmd->phy_address != phydev->addr)
+	if (cmd->phy_address != pdata->phy.address)
 		return -EINVAL;
 
 	if ((cmd->autoneg != AUTONEG_ENABLE) &&
@@ -333,23 +348,23 @@ static int xgbe_set_settings(struct net_device *netdev,
 			return -EINVAL;
 	}
 
-	cmd->advertising &= phydev->supported;
+	cmd->advertising &= pdata->phy.supported;
 	if ((cmd->autoneg == AUTONEG_ENABLE) && !cmd->advertising)
 		return -EINVAL;
 
 	ret = 0;
-	phydev->autoneg = cmd->autoneg;
-	phydev->speed = speed;
-	phydev->duplex = cmd->duplex;
-	phydev->advertising = cmd->advertising;
+	pdata->phy.autoneg = cmd->autoneg;
+	pdata->phy.speed = speed;
+	pdata->phy.duplex = cmd->duplex;
+	pdata->phy.advertising = cmd->advertising;
 
 	if (cmd->autoneg == AUTONEG_ENABLE)
-		phydev->advertising |= ADVERTISED_Autoneg;
+		pdata->phy.advertising |= ADVERTISED_Autoneg;
 	else
-		phydev->advertising &= ~ADVERTISED_Autoneg;
+		pdata->phy.advertising &= ~ADVERTISED_Autoneg;
 
 	if (netif_running(netdev))
-		ret = phy_start_aneg(phydev);
+		ret = pdata->phy_if.phy_config_aneg(pdata);
 
 	DBGPR("<--xgbe_set_settings\n");
 

drivers/net/ethernet/amd/xgbe/xgbe.h

@@ -129,7 +129,7 @@
 #include <net/dcbnl.h>
 
 #define XGBE_DRV_NAME		"amd-xgbe"
-#define XGBE_DRV_VERSION	"1.0.0-a"
+#define XGBE_DRV_VERSION	"1.0.2"
 #define XGBE_DRV_DESC		"AMD 10 Gigabit Ethernet Driver"
 
 /* Descriptor related defines */
@@ -178,14 +178,17 @@
 #define XGMAC_JUMBO_PACKET_MTU	9000
 #define XGMAC_MAX_JUMBO_PACKET	9018
 
-/* MDIO bus phy name */
-#define XGBE_PHY_NAME		"amd_xgbe_phy"
-#define XGBE_PRTAD		0
-
 /* Common property names */
 #define XGBE_MAC_ADDR_PROPERTY	"mac-address"
 #define XGBE_PHY_MODE_PROPERTY	"phy-mode"
 #define XGBE_DMA_IRQS_PROPERTY	"amd,per-channel-interrupt"
+#define XGBE_SPEEDSET_PROPERTY	"amd,speed-set"
+#define XGBE_BLWC_PROPERTY	"amd,serdes-blwc"
+#define XGBE_CDR_RATE_PROPERTY	"amd,serdes-cdr-rate"
+#define XGBE_PQ_SKEW_PROPERTY	"amd,serdes-pq-skew"
+#define XGBE_TX_AMP_PROPERTY	"amd,serdes-tx-amp"
+#define XGBE_DFE_CFG_PROPERTY	"amd,serdes-dfe-tap-config"
+#define XGBE_DFE_ENA_PROPERTY	"amd,serdes-dfe-tap-enable"
 
 /* Device-tree clock names */
 #define XGBE_DMA_CLOCK		"dma_clk"
@@ -241,6 +244,49 @@
 #define XGBE_RSS_LOOKUP_TABLE_TYPE	0
 #define XGBE_RSS_HASH_KEY_TYPE		1
 
+/* Auto-negotiation */
+#define XGBE_AN_MS_TIMEOUT		500
+#define XGBE_LINK_TIMEOUT		10
+
+#define XGBE_AN_INT_CMPLT		0x01
+#define XGBE_AN_INC_LINK		0x02
+#define XGBE_AN_PG_RCV			0x04
+#define XGBE_AN_INT_MASK		0x07
+
+/* Rate-change complete wait/retry count */
+#define XGBE_RATECHANGE_COUNT		500
+
+/* Default SerDes settings */
+#define XGBE_SPEED_10000_BLWC		0
+#define XGBE_SPEED_10000_CDR		0x7
+#define XGBE_SPEED_10000_PLL		0x1
+#define XGBE_SPEED_10000_PQ		0x12
+#define XGBE_SPEED_10000_RATE		0x0
+#define XGBE_SPEED_10000_TXAMP		0xa
+#define XGBE_SPEED_10000_WORD		0x7
+#define XGBE_SPEED_10000_DFE_TAP_CONFIG	0x1
+#define XGBE_SPEED_10000_DFE_TAP_ENABLE	0x7f
+
+#define XGBE_SPEED_2500_BLWC		1
+#define XGBE_SPEED_2500_CDR		0x2
+#define XGBE_SPEED_2500_PLL		0x0
+#define XGBE_SPEED_2500_PQ		0xa
+#define XGBE_SPEED_2500_RATE		0x1
+#define XGBE_SPEED_2500_TXAMP		0xf
+#define XGBE_SPEED_2500_WORD		0x1
+#define XGBE_SPEED_2500_DFE_TAP_CONFIG	0x3
+#define XGBE_SPEED_2500_DFE_TAP_ENABLE	0x0
+
+#define XGBE_SPEED_1000_BLWC		1
+#define XGBE_SPEED_1000_CDR		0x2
+#define XGBE_SPEED_1000_PLL		0x0
+#define XGBE_SPEED_1000_PQ		0xa
+#define XGBE_SPEED_1000_RATE		0x3
+#define XGBE_SPEED_1000_TXAMP		0xf
+#define XGBE_SPEED_1000_WORD		0x1
+#define XGBE_SPEED_1000_DFE_TAP_CONFIG	0x3
+#define XGBE_SPEED_1000_DFE_TAP_ENABLE	0x0
+
 struct xgbe_prv_data;
 
 struct xgbe_packet_data {
@@ -334,8 +380,6 @@ struct xgbe_ring_data {
 	 */
 	unsigned int state_saved;
 	struct {
-		unsigned int incomplete;
-		unsigned int context_next;
 		struct sk_buff *skb;
 		unsigned int len;
 		unsigned int error;
@@ -414,6 +458,13 @@ struct xgbe_channel {
 	struct xgbe_ring *rx_ring;
 } ____cacheline_aligned;
 
+enum xgbe_state {
+	XGBE_DOWN,
+	XGBE_LINK,
+	XGBE_LINK_INIT,
+	XGBE_LINK_ERR,
+};
+
 enum xgbe_int {
 	XGMAC_INT_DMA_CH_SR_TI,
 	XGMAC_INT_DMA_CH_SR_TPS,
@@ -445,6 +496,57 @@ enum xgbe_mtl_fifo_size {
 	XGMAC_MTL_FIFO_SIZE_256K = 0x3ff,
 };
 
+enum xgbe_speed {
+	XGBE_SPEED_1000 = 0,
+	XGBE_SPEED_2500,
+	XGBE_SPEED_10000,
+	XGBE_SPEEDS,
+};
+
+enum xgbe_an {
+	XGBE_AN_READY = 0,
+	XGBE_AN_PAGE_RECEIVED,
+	XGBE_AN_INCOMPAT_LINK,
+	XGBE_AN_COMPLETE,
+	XGBE_AN_NO_LINK,
+	XGBE_AN_ERROR,
+};
+
+enum xgbe_rx {
+	XGBE_RX_BPA = 0,
+	XGBE_RX_XNP,
+	XGBE_RX_COMPLETE,
+	XGBE_RX_ERROR,
+};
+
+enum xgbe_mode {
+	XGBE_MODE_KR = 0,
+	XGBE_MODE_KX,
+};
+
+enum xgbe_speedset {
+	XGBE_SPEEDSET_1000_10000 = 0,
+	XGBE_SPEEDSET_2500_10000,
+};
+
+struct xgbe_phy {
+	u32 supported;
+	u32 advertising;
+	u32 lp_advertising;
+
+	int address;
+
+	int autoneg;
+	int speed;
+	int duplex;
+
+	int link;
+
+	int pause_autoneg;
+	int tx_pause;
+	int rx_pause;
+};
+
 struct xgbe_mmc_stats {
 	/* Tx Stats */
 	u64 txoctetcount_gb;
@@ -492,6 +594,11 @@ struct xgbe_mmc_stats {
 	u64 rxwatchdogerror;
 };
 
+struct xgbe_ext_stats {
+	u64 tx_tso_packets;
+	u64 rx_split_header_packets;
+};
+
 struct xgbe_hw_if {
 	int (*tx_complete)(struct xgbe_ring_desc *);
 
@@ -591,6 +698,20 @@ struct xgbe_hw_if {
 	int (*set_rss_lookup_table)(struct xgbe_prv_data *, const u32 *);
 };
 
+struct xgbe_phy_if {
+	/* For initial PHY setup */
+	void (*phy_init)(struct xgbe_prv_data *);
+
+	/* For PHY support when setting device up/down */
+	int (*phy_reset)(struct xgbe_prv_data *);
+	int (*phy_start)(struct xgbe_prv_data *);
+	void (*phy_stop)(struct xgbe_prv_data *);
+
+	/* For PHY support while device is up */
+	void (*phy_status)(struct xgbe_prv_data *);
+	int (*phy_config_aneg)(struct xgbe_prv_data *);
+};
+
 struct xgbe_desc_if {
 	int (*alloc_ring_resources)(struct xgbe_prv_data *);
 	void (*free_ring_resources)(struct xgbe_prv_data *);
@@ -660,6 +781,9 @@ struct xgbe_prv_data {
 	/* XGMAC/XPCS related mmio registers */
 	void __iomem *xgmac_regs;	/* XGMAC CSRs */
 	void __iomem *xpcs_regs;	/* XPCS MMD registers */
+	void __iomem *rxtx_regs;	/* SerDes Rx/Tx CSRs */
+	void __iomem *sir0_regs;	/* SerDes integration registers (1/2) */
+	void __iomem *sir1_regs;	/* SerDes integration registers (2/2) */
 
 	/* Overall device lock */
 	spinlock_t lock;
@@ -670,10 +794,14 @@ struct xgbe_prv_data {
 	/* RSS addressing mutex */
 	struct mutex rss_mutex;
 
+	/* Flags representing xgbe_state */
+	unsigned long dev_state;
+
 	int dev_irq;
 	unsigned int per_channel_irq;
 
 	struct xgbe_hw_if hw_if;
+	struct xgbe_phy_if phy_if;
 	struct xgbe_desc_if desc_if;
 
 	/* AXI DMA settings */
@@ -682,6 +810,11 @@ struct xgbe_prv_data {
 	unsigned int arcache;
 	unsigned int awcache;
 
+	/* Service routine support */
+	struct workqueue_struct *dev_workqueue;
+	struct work_struct service_work;
+	struct timer_list service_timer;
+
 	/* Rings for Tx/Rx on a DMA channel */
 	struct xgbe_channel *channel;
 	unsigned int channel_count;
@@ -729,27 +862,12 @@ struct xgbe_prv_data {
 	u32 rss_table[XGBE_RSS_MAX_TABLE_SIZE];
 	u32 rss_options;
 
-	/* MDIO settings */
-	struct module *phy_module;
-	char *mii_bus_id;
-	struct mii_bus *mii;
-	int mdio_mmd;
-	struct phy_device *phydev;
-	int default_autoneg;
-	int default_speed;
-
-	/* Current PHY settings */
-	phy_interface_t phy_mode;
-	int phy_link;
-	int phy_speed;
-	unsigned int phy_tx_pause;
-	unsigned int phy_rx_pause;
-
 	/* Netdev related settings */
 	unsigned char mac_addr[ETH_ALEN];
 	netdev_features_t netdev_features;
 	struct napi_struct napi;
 	struct xgbe_mmc_stats mmc_stats;
+	struct xgbe_ext_stats ext_stats;
 
 	/* Filtering support */
 	unsigned long active_vlans[BITS_TO_LONGS(VLAN_N_VID)];
@@ -787,6 +905,54 @@ struct xgbe_prv_data {
 	/* Keeps track of power mode */
 	unsigned int power_down;
 
+	/* Network interface message level setting */
+	u32 msg_enable;
+
+	/* Current PHY settings */
+	phy_interface_t phy_mode;
+	int phy_link;
+	int phy_speed;
+
+	/* MDIO/PHY related settings */
+	struct xgbe_phy phy;
+	int mdio_mmd;
+	unsigned long link_check;
+
+	char an_name[IFNAMSIZ + 32];
+	struct workqueue_struct *an_workqueue;
+
+	int an_irq;
+	struct work_struct an_irq_work;
+
+	unsigned int speed_set;
+
+	/* SerDes UEFI configurable settings.
+	 *   Switching between modes/speeds requires new values for some
+	 *   SerDes settings.  The values can be supplied as device
+	 *   properties in array format.  The first array entry is for
+	 *   1GbE, second for 2.5GbE and third for 10GbE
+	 */
+	u32 serdes_blwc[XGBE_SPEEDS];
+	u32 serdes_cdr_rate[XGBE_SPEEDS];
+	u32 serdes_pq_skew[XGBE_SPEEDS];
+	u32 serdes_tx_amp[XGBE_SPEEDS];
+	u32 serdes_dfe_tap_cfg[XGBE_SPEEDS];
+	u32 serdes_dfe_tap_ena[XGBE_SPEEDS];
+
+	/* Auto-negotiation state machine support */
+	struct mutex an_mutex;
+	enum xgbe_an an_result;
+	enum xgbe_an an_state;
+	enum xgbe_rx kr_state;
+	enum xgbe_rx kx_state;
+	struct work_struct an_work;
+	unsigned int an_supported;
+	unsigned int parallel_detect;
+	unsigned int fec_ability;
+	unsigned long an_start;
+
+	unsigned int lpm_ctrl;		/* CTRL1 for resume */
+
 #ifdef CONFIG_DEBUG_FS
 	struct dentry *xgbe_debugfs;
 
@@ -800,6 +966,7 @@ struct xgbe_prv_data {
 /* Function prototypes*/
 
 void xgbe_init_function_ptrs_dev(struct xgbe_hw_if *);
+void xgbe_init_function_ptrs_phy(struct xgbe_phy_if *);
 void xgbe_init_function_ptrs_desc(struct xgbe_desc_if *);
 struct net_device_ops *xgbe_get_netdev_ops(void);
 struct ethtool_ops *xgbe_get_ethtool_ops(void);
@@ -807,14 +974,11 @@ struct ethtool_ops *xgbe_get_ethtool_ops(void);
 const struct dcbnl_rtnl_ops *xgbe_get_dcbnl_ops(void);
 #endif
 
-int xgbe_mdio_register(struct xgbe_prv_data *);
-void xgbe_mdio_unregister(struct xgbe_prv_data *);
-void xgbe_dump_phy_registers(struct xgbe_prv_data *);
 void xgbe_ptp_register(struct xgbe_prv_data *);
 void xgbe_ptp_unregister(struct xgbe_prv_data *);
-void xgbe_dump_tx_desc(struct xgbe_ring *, unsigned int, unsigned int,
-		       unsigned int);
-void xgbe_dump_rx_desc(struct xgbe_ring *, struct xgbe_ring_desc *,
+void xgbe_dump_tx_desc(struct xgbe_prv_data *, struct xgbe_ring *,
+		       unsigned int, unsigned int, unsigned int);
+void xgbe_dump_rx_desc(struct xgbe_prv_data *, struct xgbe_ring *,
 		       unsigned int);
 void xgbe_print_pkt(struct net_device *, struct sk_buff *, bool);
 void xgbe_get_all_hw_features(struct xgbe_prv_data *);
@@ -831,18 +995,6 @@ static inline void xgbe_debugfs_init(struct xgbe_prv_data *pdata) {}
 static inline void xgbe_debugfs_exit(struct xgbe_prv_data *pdata) {}
 #endif /* CONFIG_DEBUG_FS */
 
-/* NOTE: Uncomment for TX and RX DESCRIPTOR DUMP in KERNEL LOG */
-#if 0
-#define XGMAC_ENABLE_TX_DESC_DUMP
-#define XGMAC_ENABLE_RX_DESC_DUMP
-#endif
-
-/* NOTE: Uncomment for TX and RX PACKET DUMP in KERNEL LOG */
-#if 0
-#define XGMAC_ENABLE_TX_PKT_DUMP
-#define XGMAC_ENABLE_RX_PKT_DUMP
-#endif
-
 /* NOTE: Uncomment for function trace log messages in KERNEL LOG */
 #if 0
 #define YDEBUG
@@ -852,10 +1004,8 @@ static inline void xgbe_debugfs_exit(struct xgbe_prv_data *pdata) {}
 /* For debug prints */
 #ifdef YDEBUG
 #define DBGPR(x...) pr_alert(x)
-#define DBGPHY_REGS(x...) xgbe_dump_phy_registers(x)
 #else
 #define DBGPR(x...) do { } while (0)
-#define DBGPHY_REGS(x...) do { } while (0)
 #endif
 
 #ifdef YDEBUG_MDIO

drivers/net/phy/Kconfig

@@ -24,13 +24,6 @@ config AMD_PHY
 	---help---
 	  Currently supports the am79c874
 
-config AMD_XGBE_PHY
-	tristate "Driver for the AMD 10GbE (amd-xgbe) PHYs"
-	depends on (OF || ACPI) && HAS_IOMEM
-	depends on ARM64 || COMPILE_TEST
-	---help---
-	  Currently supports the AMD 10GbE PHY
-
 config MARVELL_PHY
 	tristate "Drivers for Marvell PHYs"
 	---help---

drivers/net/phy/Makefile

@@ -33,5 +33,4 @@ obj-$(CONFIG_MDIO_BUS_MUX_GPIO)	+= mdio-mux-gpio.o
 obj-$(CONFIG_MDIO_BUS_MUX_MMIOREG) += mdio-mux-mmioreg.o
 obj-$(CONFIG_MDIO_SUN4I)	+= mdio-sun4i.o
 obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
-obj-$(CONFIG_AMD_XGBE_PHY)	+= amd-xgbe-phy.o
 obj-$(CONFIG_MDIO_BCM_UNIMAC)	+= mdio-bcm-unimac.o