Commit 557e2a39 authored by Giuseppe CAVALLARO's avatar Giuseppe CAVALLARO Committed by David S. Miller

stmmac: improve and up-to-date the documentation

This patch adds new information for the driver
especially about its platform structure fields.
Signed-off-by: default avatarGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 36bcfe7d
......@@ -7,7 +7,7 @@ This is the driver for the MAC 10/100/1000 on-chip Ethernet controllers
(Synopsys IP blocks); it has been fully tested on STLinux platforms.
Currently this network device driver is for all STM embedded MAC/GMAC
(7xxx SoCs). Other platforms start using it i.e. ARM SPEAr.
(i.e. 7xxx/5xxx SoCs) and it's known working on other platforms i.e. ARM SPEAr.
DWC Ether MAC 10/100/1000 Universal version 3.41a and DWC Ether MAC 10/100
Universal version 4.0 have been used for developing the first code
......@@ -71,7 +71,7 @@ Several performance tests on STM platforms showed this optimisation allows to sp
the CPU while having the maximum throughput.
4.4) WOL
Wake up on Lan feature through Magic Frame is only supported for the GMAC
Wake up on Lan feature through Magic and Unicast frames are supported for the GMAC
core.
4.5) DMA descriptors
......@@ -91,11 +91,15 @@ LRO is not supported.
The driver is compatible with PAL to work with PHY and GPHY devices.
4.9) Platform information
Several information came from the platform; please refer to the
driver's Header file in include/linux directory.
Several driver's information can be passed through the platform
These are included in the include/linux/stmmac.h header file
and detailed below as well:
struct plat_stmmacenet_data {
struct plat_stmmacenet_data {
int bus_id;
int phy_addr;
int interface;
struct stmmac_mdio_bus_data *mdio_bus_data;
int pbl;
int clk_csr;
int has_gmac;
......@@ -103,67 +107,135 @@ struct plat_stmmacenet_data {
int tx_coe;
int bugged_jumbo;
int pmt;
void (*fix_mac_speed)(void *priv, unsigned int speed);
void (*bus_setup)(unsigned long ioaddr);
#ifdef CONFIG_STM_DRIVERS
struct stm_pad_config *pad_config;
#endif
void *bsp_priv;
};
int force_sf_dma_mode;
void (*fix_mac_speed)(void *priv, unsigned int speed);
void (*bus_setup)(void __iomem *ioaddr);
int (*init)(struct platform_device *pdev);
void (*exit)(struct platform_device *pdev);
void *bsp_priv;
};
Where:
- pbl (Programmable Burst Length) is maximum number of
beats to be transferred in one DMA transaction.
GMAC also enables the 4xPBL by default.
- fix_mac_speed and bus_setup are used to configure internal target
registers (on STM platforms);
- has_gmac: GMAC core is on board (get it at run-time in the next step);
- bus_id: bus identifier.
- tx_coe: core is able to perform the tx csum in HW.
- enh_desc: if sets the MAC will use the enhanced descriptor structure.
- clk_csr: CSR Clock range selection.
- bugged_jumbo: some HWs are not able to perform the csum in HW for
over-sized frames due to limited buffer sizes. Setting this
flag the csum will be done in SW on JUMBO frames.
struct plat_stmmacphy_data {
int bus_id;
int phy_addr;
unsigned int phy_mask;
int interface;
int (*phy_reset)(void *priv);
void *priv;
};
o bus_id: bus identifier.
o phy_addr: the physical address can be passed from the platform.
If it is set to -1 the driver will automatically
detect it at run-time by probing all the 32 addresses.
o interface: PHY device's interface.
o mdio_bus_data: specific platform fields for the MDIO bus.
o pbl: the Programmable Burst Length is maximum number of beats to
be transferred in one DMA transaction.
GMAC also enables the 4xPBL by default.
o clk_csr: CSR Clock range selection.
o has_gmac: uses the GMAC core.
o enh_desc: if sets the MAC will use the enhanced descriptor structure.
o tx_coe: core is able to perform the tx csum in HW.
o bugged_jumbo: some HWs are not able to perform the csum in HW for
over-sized frames due to limited buffer sizes.
Setting this flag the csum will be done in SW on
JUMBO frames.
o pmt: core has the embedded power module (optional).
o force_sf_dma_mode: force DMA to use the Store and Forward mode
instead of the Threshold.
o fix_mac_speed: this callback is used for modifying some syscfg registers
(on ST SoCs) according to the link speed negotiated by the
physical layer .
o bus_setup: perform HW setup of the bus. For example, on some ST platforms
this field is used to configure the AMBA bridge to generate more
efficient STBus traffic.
o init/exit: callbacks used for calling a custom initialisation;
this is sometime necessary on some platforms (e.g. ST boxes)
where the HW needs to have set some PIO lines or system cfg
registers.
o custom_cfg: this is a custom configuration that can be passed while
initialising the resources.
The we have:
struct stmmac_mdio_bus_data {
int bus_id;
int (*phy_reset)(void *priv);
unsigned int phy_mask;
int *irqs;
int probed_phy_irq;
};
Where:
- bus_id: bus identifier;
- phy_addr: physical address used for the attached phy device;
set it to -1 to get it at run-time;
- interface: physical MII interface mode;
- phy_reset: hook to reset HW function.
SOURCES:
- Kconfig
- Makefile
- stmmac_main.c: main network device driver;
- stmmac_mdio.c: mdio functions;
- stmmac_ethtool.c: ethtool support;
- stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts
Only tested on ST40 platforms based.
- stmmac.h: private driver structure;
- common.h: common definitions and VFTs;
- descs.h: descriptor structure definitions;
- dwmac1000_core.c: GMAC core functions;
- dwmac1000_dma.c: dma functions for the GMAC chip;
- dwmac1000.h: specific header file for the GMAC;
- dwmac100_core: MAC 100 core and dma code;
- dwmac100_dma.c: dma funtions for the MAC chip;
- dwmac1000.h: specific header file for the MAC;
- dwmac_lib.c: generic DMA functions shared among chips
- enh_desc.c: functions for handling enhanced descriptors
- norm_desc.c: functions for handling normal descriptors
TODO:
- XGMAC controller is not supported.
- Review the timer optimisation code to use an embedded device that seems to be
o bus_id: bus identifier;
o phy_reset: hook to reset the phy device attached to the bus.
o phy_mask: phy mask passed when register the MDIO bus within the driver.
o irqs: list of IRQs, one per PHY.
o probed_phy_irq: if irqs is NULL, use this for probed PHY.
Below an example how the structures above are using on ST platforms.
static struct plat_stmmacenet_data stxYYY_ethernet_platform_data = {
.pbl = 32,
.has_gmac = 0,
.enh_desc = 0,
.fix_mac_speed = stxYYY_ethernet_fix_mac_speed,
|
|-> to write an internal syscfg
| on this platform when the
| link speed changes from 10 to
| 100 and viceversa
.init = &stmmac_claim_resource,
|
|-> On ST SoC this calls own "PAD"
| manager framework to claim
| all the resources necessary
| (GPIO ...). The .custom_cfg field
| is used to pass a custom config.
};
Below the usage of the stmmac_mdio_bus_data: on this SoC, in fact,
there are two MAC cores: one MAC is for MDIO Bus/PHY emulation
with fixed_link support.
static struct stmmac_mdio_bus_data stmmac1_mdio_bus = {
.bus_id = 1,
|
|-> phy device on the bus_id 1
.phy_reset = phy_reset;
|
|-> function to provide the phy_reset on this board
.phy_mask = 0,
};
static struct fixed_phy_status stmmac0_fixed_phy_status = {
.link = 1,
.speed = 100,
.duplex = 1,
};
During the board's device_init we can configure the first
MAC for fixed_link by calling:
fixed_phy_add(PHY_POLL, 1, &stmmac0_fixed_phy_status));)
and the second one, with a real PHY device attached to the bus,
by using the stmmac_mdio_bus_data structure (to provide the id, the
reset procedure etc).
4.10) List of source files:
o Kconfig
o Makefile
o stmmac_main.c: main network device driver;
o stmmac_mdio.c: mdio functions;
o stmmac_ethtool.c: ethtool support;
o stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts
Only tested on ST40 platforms based.
o stmmac.h: private driver structure;
o common.h: common definitions and VFTs;
o descs.h: descriptor structure definitions;
o dwmac1000_core.c: GMAC core functions;
o dwmac1000_dma.c: dma functions for the GMAC chip;
o dwmac1000.h: specific header file for the GMAC;
o dwmac100_core: MAC 100 core and dma code;
o dwmac100_dma.c: dma funtions for the MAC chip;
o dwmac1000.h: specific header file for the MAC;
o dwmac_lib.c: generic DMA functions shared among chips
o enh_desc.c: functions for handling enhanced descriptors
o norm_desc.c: functions for handling normal descriptors
5) TODO:
o XGMAC is not supported.
o Review the timer optimisation code to use an embedded device that will be
available in new chip generations.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment