Commit 55cac248 authored by Alexander Duyck's avatar Alexander Duyck Committed by David S. Miller

igb: Add full support for 82580 devices

This patch makes use of the 82580 PHY and MAC support added and adds a set
of supported device IDs for said hardware.
Signed-off-by: default avatarAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent bb2ac47b
......@@ -330,6 +330,7 @@
#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
#define E1000_ICR_VMMB 0x00000100 /* VM MB event */
#define E1000_ICR_DRSTA 0x40000000 /* Device Reset Asserted */
/* If this bit asserted, the driver should claim the interrupt */
#define E1000_ICR_INT_ASSERTED 0x80000000
/* LAN connected device generates an interrupt */
......@@ -371,6 +372,7 @@
#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
#define E1000_IMS_DRSTA E1000_ICR_DRSTA /* Device Reset Asserted */
#define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
/* Extended Interrupt Mask Set */
......@@ -379,6 +381,7 @@
/* Interrupt Cause Set */
#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_ICS_DRSTA E1000_ICR_DRSTA /* Device Reset Aserted */
/* Extended Interrupt Cause Set */
......@@ -717,4 +720,8 @@
#define E1000_VFTA_ENTRY_MASK 0x7F
#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
/* DMA Coalescing register fields */
#define E1000_PCIEMISC_LX_DECISION 0x00000080 /* Lx power decision based
on DMA coal */
#endif
......@@ -89,6 +89,8 @@
#define E1000_SYSTIML 0x0B600 /* System time register Low - RO */
#define E1000_SYSTIMH 0x0B604 /* System time register High - RO */
#define E1000_TIMINCA 0x0B608 /* Increment attributes register - RW */
#define E1000_TSAUXC 0x0B640 /* Timesync Auxiliary Control register */
#define E1000_SYSTIMR 0x0B6F8 /* System time register Residue */
/* Filtering Registers */
#define E1000_SAQF(_n) (0x5980 + 4 * (_n))
......@@ -318,4 +320,6 @@
#define array_rd32(reg, offset) \
(readl(hw->hw_addr + reg + ((offset) << 2)))
/* DMA Coalescing registers */
#define E1000_PCIEMISC 0x05BB8 /* PCIE misc config register */
#endif
......@@ -320,6 +320,7 @@ struct igb_adapter {
#define IGB_FLAG_QUEUE_PAIRS (1 << 3)
#define IGB_82576_TSYNC_SHIFT 19
#define IGB_82580_TSYNC_SHIFT 24
enum e1000_state_t {
__IGB_TESTING,
__IGB_RESETTING,
......
......@@ -881,6 +881,49 @@ struct igb_reg_test {
#define TABLE64_TEST_LO 5
#define TABLE64_TEST_HI 6
/* 82580 reg test */
static struct igb_reg_test reg_test_82580[] = {
{ E1000_FCAL, 0x100, 1, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_FCAH, 0x100, 1, PATTERN_TEST, 0x0000FFFF, 0xFFFFFFFF },
{ E1000_FCT, 0x100, 1, PATTERN_TEST, 0x0000FFFF, 0xFFFFFFFF },
{ E1000_VET, 0x100, 1, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_RDBAL(0), 0x100, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
{ E1000_RDBAH(0), 0x100, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_RDLEN(0), 0x100, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
{ E1000_RDBAL(4), 0x40, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
{ E1000_RDBAH(4), 0x40, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_RDLEN(4), 0x40, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
/* RDH is read-only for 82580, only test RDT. */
{ E1000_RDT(0), 0x100, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
{ E1000_RDT(4), 0x40, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
{ E1000_FCRTH, 0x100, 1, PATTERN_TEST, 0x0000FFF0, 0x0000FFF0 },
{ E1000_FCTTV, 0x100, 1, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
{ E1000_TIPG, 0x100, 1, PATTERN_TEST, 0x3FFFFFFF, 0x3FFFFFFF },
{ E1000_TDBAL(0), 0x100, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
{ E1000_TDBAH(0), 0x100, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_TDLEN(0), 0x100, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
{ E1000_TDBAL(4), 0x40, 4, PATTERN_TEST, 0xFFFFFF80, 0xFFFFFFFF },
{ E1000_TDBAH(4), 0x40, 4, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_TDLEN(4), 0x40, 4, PATTERN_TEST, 0x000FFFF0, 0x000FFFFF },
{ E1000_TDT(0), 0x100, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
{ E1000_TDT(4), 0x40, 4, PATTERN_TEST, 0x0000FFFF, 0x0000FFFF },
{ E1000_RCTL, 0x100, 1, SET_READ_TEST, 0xFFFFFFFF, 0x00000000 },
{ E1000_RCTL, 0x100, 1, SET_READ_TEST, 0x04CFB0FE, 0x003FFFFB },
{ E1000_RCTL, 0x100, 1, SET_READ_TEST, 0x04CFB0FE, 0xFFFFFFFF },
{ E1000_TCTL, 0x100, 1, SET_READ_TEST, 0xFFFFFFFF, 0x00000000 },
{ E1000_RA, 0, 16, TABLE64_TEST_LO,
0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_RA, 0, 16, TABLE64_TEST_HI,
0x83FFFFFF, 0xFFFFFFFF },
{ E1000_RA2, 0, 8, TABLE64_TEST_LO,
0xFFFFFFFF, 0xFFFFFFFF },
{ E1000_RA2, 0, 8, TABLE64_TEST_HI,
0x83FFFFFF, 0xFFFFFFFF },
{ E1000_MTA, 0, 128, TABLE32_TEST,
0xFFFFFFFF, 0xFFFFFFFF },
{ 0, 0, 0, 0 }
};
/* 82576 reg test */
static struct igb_reg_test reg_test_82576[] = {
{ E1000_FCAL, 0x100, 1, PATTERN_TEST, 0xFFFFFFFF, 0xFFFFFFFF },
......@@ -1013,6 +1056,10 @@ static int igb_reg_test(struct igb_adapter *adapter, u64 *data)
u32 i, toggle;
switch (adapter->hw.mac.type) {
case e1000_82580:
test = reg_test_82580;
toggle = 0x7FEFF3FF;
break;
case e1000_82576:
test = reg_test_82576;
toggle = 0x7FFFF3FF;
......@@ -1167,6 +1214,9 @@ static int igb_intr_test(struct igb_adapter *adapter, u64 *data)
case e1000_82576:
ics_mask = 0x77D4FBFD;
break;
case e1000_82580:
ics_mask = 0x77DCFED5;
break;
default:
ics_mask = 0x7FFFFFFF;
break;
......@@ -1338,6 +1388,9 @@ static int igb_integrated_phy_loopback(struct igb_adapter *adapter)
igb_write_phy_reg(hw, PHY_CONTROL, 0x9140);
/* autoneg off */
igb_write_phy_reg(hw, PHY_CONTROL, 0x8140);
} else if (hw->phy.type == e1000_phy_82580) {
/* enable MII loopback */
igb_write_phy_reg(hw, I82580_PHY_LBK_CTRL, 0x8041);
}
ctrl_reg = rd32(E1000_CTRL);
......
......@@ -49,7 +49,7 @@
#endif
#include "igb.h"
#define DRV_VERSION "1.3.16-k2"
#define DRV_VERSION "2.1.0-k2"
char igb_driver_name[] = "igb";
char igb_driver_version[] = DRV_VERSION;
static const char igb_driver_string[] =
......@@ -61,6 +61,11 @@ static const struct e1000_info *igb_info_tbl[] = {
};
static struct pci_device_id igb_pci_tbl[] = {
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_COPPER), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_FIBER), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SERDES), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SGMII), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_COPPER_DUAL), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS), board_82575 },
{ PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS_SERDES), board_82575 },
......@@ -195,6 +200,16 @@ static cycle_t igb_read_clock(const struct cyclecounter *tc)
u64 stamp = 0;
int shift = 0;
/*
* The timestamp latches on lowest register read. For the 82580
* the lowest register is SYSTIMR instead of SYSTIML. However we never
* adjusted TIMINCA so SYSTIMR will just read as all 0s so ignore it.
*/
if (hw->mac.type == e1000_82580) {
stamp = rd32(E1000_SYSTIMR) >> 8;
shift = IGB_82580_TSYNC_SHIFT;
}
stamp |= (u64)rd32(E1000_SYSTIML) << shift;
stamp |= (u64)rd32(E1000_SYSTIMH) << (shift + 32);
return stamp;
......@@ -304,6 +319,7 @@ static void igb_cache_ring_register(struct igb_adapter *adapter)
Q_IDX_82576(j);
}
case e1000_82575:
case e1000_82580:
default:
for (; i < adapter->num_rx_queues; i++)
adapter->rx_ring[i].reg_idx = rbase_offset + i;
......@@ -443,6 +459,39 @@ static void igb_assign_vector(struct igb_q_vector *q_vector, int msix_vector)
}
q_vector->eims_value = 1 << msix_vector;
break;
case e1000_82580:
/* 82580 uses the same table-based approach as 82576 but has fewer
entries as a result we carry over for queues greater than 4. */
if (rx_queue > IGB_N0_QUEUE) {
index = (rx_queue >> 1);
ivar = array_rd32(E1000_IVAR0, index);
if (rx_queue & 0x1) {
/* vector goes into third byte of register */
ivar = ivar & 0xFF00FFFF;
ivar |= (msix_vector | E1000_IVAR_VALID) << 16;
} else {
/* vector goes into low byte of register */
ivar = ivar & 0xFFFFFF00;
ivar |= msix_vector | E1000_IVAR_VALID;
}
array_wr32(E1000_IVAR0, index, ivar);
}
if (tx_queue > IGB_N0_QUEUE) {
index = (tx_queue >> 1);
ivar = array_rd32(E1000_IVAR0, index);
if (tx_queue & 0x1) {
/* vector goes into high byte of register */
ivar = ivar & 0x00FFFFFF;
ivar |= (msix_vector | E1000_IVAR_VALID) << 24;
} else {
/* vector goes into second byte of register */
ivar = ivar & 0xFFFF00FF;
ivar |= (msix_vector | E1000_IVAR_VALID) << 8;
}
array_wr32(E1000_IVAR0, index, ivar);
}
q_vector->eims_value = 1 << msix_vector;
break;
default:
BUG();
break;
......@@ -484,6 +533,7 @@ static void igb_configure_msix(struct igb_adapter *adapter)
break;
case e1000_82576:
case e1000_82580:
/* Turn on MSI-X capability first, or our settings
* won't stick. And it will take days to debug. */
wr32(E1000_GPIE, E1000_GPIE_MSIX_MODE |
......@@ -866,6 +916,7 @@ static int igb_request_irq(struct igb_adapter *adapter)
E1000_EICR_TX_QUEUE0 |
E1000_EIMS_OTHER));
break;
case e1000_82580:
case e1000_82576:
wr32(E1000_IVAR0, E1000_IVAR_VALID);
break;
......@@ -959,10 +1010,15 @@ static void igb_irq_enable(struct igb_adapter *adapter)
wr32(E1000_MBVFIMR, 0xFF);
ims |= E1000_IMS_VMMB;
}
if (adapter->hw.mac.type == e1000_82580)
ims |= E1000_IMS_DRSTA;
wr32(E1000_IMS, ims);
} else {
wr32(E1000_IMS, IMS_ENABLE_MASK);
wr32(E1000_IAM, IMS_ENABLE_MASK);
wr32(E1000_IMS, IMS_ENABLE_MASK |
E1000_IMS_DRSTA);
wr32(E1000_IAM, IMS_ENABLE_MASK |
E1000_IMS_DRSTA);
}
}
......@@ -1184,6 +1240,10 @@ void igb_reset(struct igb_adapter *adapter)
* To take effect CTRL.RST is required.
*/
switch (mac->type) {
case e1000_82580:
pba = rd32(E1000_RXPBS);
pba = igb_rxpbs_adjust_82580(pba);
break;
case e1000_82576:
pba = rd32(E1000_RXPBS);
pba &= E1000_RXPBS_SIZE_MASK_82576;
......@@ -1278,6 +1338,11 @@ void igb_reset(struct igb_adapter *adapter)
if (hw->mac.ops.init_hw(hw))
dev_err(&pdev->dev, "Hardware Error\n");
if (hw->mac.type == e1000_82580) {
u32 reg = rd32(E1000_PCIEMISC);
wr32(E1000_PCIEMISC,
reg & ~E1000_PCIEMISC_LX_DECISION);
}
igb_update_mng_vlan(adapter);
/* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
......@@ -1508,6 +1573,10 @@ static int __devinit igb_probe(struct pci_dev *pdev,
if (hw->bus.func == 0)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
else if (hw->mac.type == e1000_82580)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A +
NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1,
&eeprom_data);
else if (hw->bus.func == 1)
hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
......@@ -1746,6 +1815,48 @@ static void igb_init_hw_timer(struct igb_adapter *adapter)
struct e1000_hw *hw = &adapter->hw;
switch (hw->mac.type) {
case e1000_82580:
memset(&adapter->cycles, 0, sizeof(adapter->cycles));
adapter->cycles.read = igb_read_clock;
adapter->cycles.mask = CLOCKSOURCE_MASK(64);
adapter->cycles.mult = 1;
/*
* The 82580 timesync updates the system timer every 8ns by 8ns
* and the value cannot be shifted. Instead we need to shift
* the registers to generate a 64bit timer value. As a result
* SYSTIMR/L/H, TXSTMPL/H, RXSTMPL/H all have to be shifted by
* 24 in order to generate a larger value for synchronization.
*/
adapter->cycles.shift = IGB_82580_TSYNC_SHIFT;
/* disable system timer temporarily by setting bit 31 */
wr32(E1000_TSAUXC, 0x80000000);
wrfl();
/* Set registers so that rollover occurs soon to test this. */
wr32(E1000_SYSTIMR, 0x00000000);
wr32(E1000_SYSTIML, 0x80000000);
wr32(E1000_SYSTIMH, 0x000000FF);
wrfl();
/* enable system timer by clearing bit 31 */
wr32(E1000_TSAUXC, 0x0);
wrfl();
timecounter_init(&adapter->clock,
&adapter->cycles,
ktime_to_ns(ktime_get_real()));
/*
* Synchronize our NIC clock against system wall clock. NIC
* time stamp reading requires ~3us per sample, each sample
* was pretty stable even under load => only require 10
* samples for each offset comparison.
*/
memset(&adapter->compare, 0, sizeof(adapter->compare));
adapter->compare.source = &adapter->clock;
adapter->compare.target = ktime_get_real;
adapter->compare.num_samples = 10;
timecompare_update(&adapter->compare, 0);
break;
case e1000_82576:
/*
* Initialize hardware timer: we keep it running just in case
......@@ -2217,6 +2328,10 @@ static void igb_setup_mrqc(struct igb_adapter *adapter)
if (adapter->vfs_allocated_count) {
/* 82575 and 82576 supports 2 RSS queues for VMDq */
switch (hw->mac.type) {
case e1000_82580:
num_rx_queues = 1;
shift = 0;
break;
case e1000_82576:
shift = 3;
num_rx_queues = 2;
......@@ -3694,6 +3809,9 @@ static void igb_tx_timeout(struct net_device *netdev)
/* Do the reset outside of interrupt context */
adapter->tx_timeout_count++;
if (hw->mac.type == e1000_82580)
hw->dev_spec._82575.global_device_reset = true;
schedule_work(&adapter->reset_task);
wr32(E1000_EICS,
(adapter->eims_enable_mask & ~adapter->eims_other));
......@@ -4700,6 +4818,13 @@ static void igb_systim_to_hwtstamp(struct igb_adapter *adapter,
{
u64 ns;
/*
* The 82580 starts with 1ns at bit 0 in RX/TXSTMPL, shift this up to
* 24 to match clock shift we setup earlier.
*/
if (adapter->hw.mac.type == e1000_82580)
regval <<= IGB_82580_TSYNC_SHIFT;
ns = timecounter_cyc2time(&adapter->clock, regval);
timecompare_update(&adapter->compare, ns);
memset(shhwtstamps, 0, sizeof(struct skb_shared_hwtstamps));
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment