Merge tag 'soc-fsl-fix-v4.19-2' into HEAD

NXP/FSL SoC driver fixes for v4.19 round 2

- Fix crash of qman_portal by deferring its probe if qman is not probed

MAINTAINERS

@@ -1251,7 +1251,7 @@ N:	meson
 
 ARM/Annapurna Labs ALPINE ARCHITECTURE
 M:	Tsahee Zidenberg <tsahee@annapurnalabs.com>
-M:	Antoine Tenart <antoine.tenart@free-electrons.com>
+M:	Antoine Tenart <antoine.tenart@bootlin.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-alpine/

arch/arm/boot/dts/am4372.dtsi

@@ -469,6 +469,7 @@ rtc: rtc@44e3e000 {
 			ti,hwmods = "rtc";
 			clocks = <&clk_32768_ck>;
 			clock-names = "int-clk";
+			system-power-controller;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts

@@ -11,6 +11,7 @@
 #include "sama5d2-pinfunc.h"
 #include <dt-bindings/mfd/atmel-flexcom.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/at91.h>
 
 / {
 	model = "Atmel SAMA5D2 PTC EK";
@@ -299,6 +300,7 @@ re_we_data {
 							 <PIN_PA30__NWE_NANDWE>,
 							 <PIN_PB2__NRD_NANDOE>;
 						bias-pull-up;
+						atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>;
 					};
 
 					ale_cle_rdy_cs {

arch/arm/boot/dts/bcm63138.dtsi

@@ -106,21 +106,23 @@ gic: interrupt-controller@1e100 {
 		global_timer: timer@1e200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x1e200 0x20>;
-			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&axi_clk>;
 		};
 
 		local_timer: local-timer@1e600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x1e600 0x20>;
-			interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_EDGE_RISING)>;
 			clocks = <&axi_clk>;
 		};
 
 		twd_watchdog: watchdog@1e620 {
 			compatible = "arm,cortex-a9-twd-wdt";
 			reg = <0x1e620 0x20>;
-			interrupts = <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
 		armpll: armpll {
@@ -158,7 +160,7 @@ timer: timer@80 {
 		serial0: serial@600 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x600 0x1b>;
-			interrupts = <GIC_SPI 32 0>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&periph_clk>;
 			clock-names = "periph";
 			status = "disabled";
@@ -167,7 +169,7 @@ serial0: serial@600 {
 		serial1: serial@620 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x620 0x1b>;
-			interrupts = <GIC_SPI 33 0>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&periph_clk>;
 			clock-names = "periph";
 			status = "disabled";
@@ -180,7 +182,7 @@ nand: nand@2000 {
 			reg = <0x2000 0x600>, <0xf0 0x10>;
 			reg-names = "nand", "nand-int-base";
 			status = "disabled";
-			interrupts = <GIC_SPI 38 0>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "nand";
 		};
 

arch/arm/boot/dts/imx23-evk.dts

@@ -13,6 +13,43 @@ memory@40000000 {
 		reg = <0x40000000 0x08000000>;
 	};
 
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 29 0>;
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 18 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	apb@80000000 {
 		apbh@80000000 {
 			gpmi-nand@8000c000 {
@@ -52,31 +89,11 @@ MX23_PAD_SSP1_DETECT__SSP1_DETECT
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a>;
-				lcd-supply = <&reg_lcd_3v3>;
-				display = <&display0>;
 				status = "okay";
 
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9200000>;
-							hactive = <480>;
-							vactive = <272>;
-							hback-porch = <15>;
-							hfront-porch = <8>;
-							vback-porch = <12>;
-							vfront-porch = <4>;
-							hsync-len = <1>;
-							vsync-len = <1>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
+				port {
+					display_out: endpoint {
+						remote-endpoint = <&panel_in>;
 					};
 				};
 			};
@@ -118,32 +135,7 @@ usb0: usb@80080000 {
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_vddio_sd0: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 29 0>;
-		};
-
-		reg_lcd_3v3: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 18 0>;
-			enable-active-high;
-		};
-	};
-
-	backlight {
+	backlight_display: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 2 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;

arch/arm/boot/dts/imx28-evk.dts

@@ -13,6 +13,87 @@ memory@40000000 {
 		reg = <0x40000000 0x08000000>;
 	};
 
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+
+	reg_fec_3v3: regulator-fec-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 15 0>;
+	};
+
+	reg_usb0_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 9 0>;
+		enable-active-high;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 8 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 30 0>;
+		enable-active-high;
+	};
+
+	reg_can_3v3: regulator-can-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 13 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
 	apb@80000000 {
 		apbh@80000000 {
 			gpmi-nand@8000c000 {
@@ -116,31 +197,11 @@ lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_24bit_pins_a
 					     &lcdif_pins_evk>;
-				lcd-supply = <&reg_lcd_3v3>;
-				display = <&display0>;
 				status = "okay";
 
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33500000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <89>;
-							hfront-porch = <164>;
-							vback-porch = <23>;
-							vfront-porch = <10>;
-							hsync-len = <10>;
-							vsync-len = <10>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
+				port {
+					display_out: endpoint {
+						remote-endpoint = <&panel_in>;
 					};
 				};
 			};
@@ -269,80 +330,6 @@ mac1: ethernet@800f4000 {
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_vddio_sd0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 28 0>;
-		};
-
-		reg_fec_3v3: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "fec-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 15 0>;
-		};
-
-		reg_usb0_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 9 0>;
-			enable-active-high;
-		};
-
-		reg_usb1_vbus: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 8 0>;
-			enable-active-high;
-		};
-
-		reg_lcd_3v3: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 30 0>;
-			enable-active-high;
-		};
-
-		reg_can_3v3: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "can-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 13 0>;
-			enable-active-high;
-		};
-
-	};
-
 	sound {
 		compatible = "fsl,imx28-evk-sgtl5000",
 			     "fsl,mxs-audio-sgtl5000";
@@ -363,7 +350,7 @@ user {
 		};
 	};
 
-	backlight {
+	backlight_display: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm 2 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;

arch/arm/boot/dts/imx7d.dtsi

@@ -126,10 +126,14 @@ pcie: pcie@33800000 {
 		interrupt-names = "msi";
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0x7>;
-		interrupt-map = <0 0 0 1 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 2 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 3 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 4 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		/*
+		 * Reference manual lists pci irqs incorrectly
+		 * Real hardware ordering is same as imx6: D+MSI, C, B, A
+		 */
+		interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
 			 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
 			 <&clks IMX7D_PCIE_PHY_ROOT_CLK>;

arch/arm/boot/dts/omap4-droid4-xt894.dts

@@ -354,7 +354,7 @@ &mmc1 {
 &mmc2 {
 	vmmc-supply = <&vsdio>;
 	bus-width = <8>;
-	non-removable;
+	ti,non-removable;
 };
 
 &mmc3 {
@@ -621,15 +621,6 @@ OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_clkx */
 		OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)	/* abe_mcbsp3_fsx */
 		>;
 	};
-};
-
-&omap4_pmx_wkup {
-	usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
-		/* gpio_wk0 */
-		pinctrl-single,pins = <
-		OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
-		>;
-	};
 
 	vibrator_direction_pin: pinmux_vibrator_direction_pin {
 		pinctrl-single,pins = <
@@ -644,6 +635,15 @@ OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)	/* dmtimer9_pwm_evt (gpio_28) */
 	};
 };
 
+&omap4_pmx_wkup {
+	usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
+		/* gpio_wk0 */
+		pinctrl-single,pins = <
+		OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
+		>;
+	};
+};
+
 /*
  * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
  * uart1 wakeirq.

arch/arm/boot/dts/sun8i-r40.dtsi

@@ -800,8 +800,7 @@ hdmi_out: port@1 {
 		};
 
 		hdmi_phy: hdmi-phy@1ef0000 {
-			compatible = "allwinner,sun8i-r40-hdmi-phy",
-				     "allwinner,sun50i-a64-hdmi-phy";
+			compatible = "allwinner,sun8i-r40-hdmi-phy";
 			reg = <0x01ef0000 0x10000>;
 			clocks = <&ccu CLK_BUS_HDMI1>, <&ccu CLK_HDMI_SLOW>,
 				 <&ccu 7>, <&ccu 16>;

arch/arm/configs/imx_v6_v7_defconfig

@@ -257,6 +257,7 @@ CONFIG_IMX_IPUV3_CORE=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_LVDS=y
 CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_PANEL_SEIKO_43WVF1G=y
 CONFIG_DRM_DW_HDMI_AHB_AUDIO=m
 CONFIG_DRM_DW_HDMI_CEC=y
 CONFIG_DRM_IMX=y

arch/arm/configs/mxs_defconfig

@@ -95,6 +95,7 @@ CONFIG_MFD_MXS_LRADC=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_DRM=y
+CONFIG_DRM_PANEL_SEIKO_43WVF1G=y
 CONFIG_DRM_MXSFB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y

arch/arm/configs/versatile_defconfig

@@ -5,19 +5,19 @@ CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_PARTITION_ADVANCED=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_VERSATILE=y
 CONFIG_AEABI=y
 CONFIG_OABI_COMPAT=y
-CONFIG_CMA=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="root=1f03 mem=32M"
 CONFIG_FPE_NWFPE=y
 CONFIG_VFP=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -59,6 +59,7 @@ CONFIG_GPIO_PL061=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_ARM_VERSATILE=y
 CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_DUMB_VGA_DAC=y
 CONFIG_DRM_PL111=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y
@@ -89,9 +90,10 @@ CONFIG_NFSD=y
 CONFIG_NFSD_V3=y
 CONFIG_NLS_CODEPAGE_850=m
 CONFIG_NLS_ISO8859_1=m
+CONFIG_FONTS=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
-CONFIG_FONTS=y
-CONFIG_FONT_ACORN_8x8=y

arch/arm/mach-omap2/omap_hwmod.c

@@ -2160,6 +2160,37 @@ static int of_dev_hwmod_lookup(struct device_node *np,
 	return -ENODEV;
 }
 
+/**
+ * omap_hwmod_fix_mpu_rt_idx - fix up mpu_rt_idx register offsets
+ *
+ * @oh: struct omap_hwmod *
+ * @np: struct device_node *
+ *
+ * Fix up module register offsets for modules with mpu_rt_idx.
+ * Only needed for cpsw with interconnect target module defined
+ * in device tree while still using legacy hwmod platform data
+ * for rev, sysc and syss registers.
+ *
+ * Can be removed when all cpsw hwmod platform data has been
+ * dropped.
+ */
+static void omap_hwmod_fix_mpu_rt_idx(struct omap_hwmod *oh,
+				      struct device_node *np,
+				      struct resource *res)
+{
+	struct device_node *child = NULL;
+	int error;
+
+	child = of_get_next_child(np, child);
+	if (!child)
+		return;
+
+	error = of_address_to_resource(child, oh->mpu_rt_idx, res);
+	if (error)
+		pr_err("%s: error mapping mpu_rt_idx: %i\n",
+		       __func__, error);
+}
+
 /**
  * omap_hwmod_parse_module_range - map module IO range from device tree
  * @oh: struct omap_hwmod *
@@ -2220,7 +2251,13 @@ int omap_hwmod_parse_module_range(struct omap_hwmod *oh,
 	size = be32_to_cpup(ranges);
 
 	pr_debug("omap_hwmod: %s %s at 0x%llx size 0x%llx\n",
-		 oh->name, np->name, base, size);
+		 oh ? oh->name : "", np->name, base, size);
+
+	if (oh && oh->mpu_rt_idx) {
+		omap_hwmod_fix_mpu_rt_idx(oh, np, res);
+
+		return 0;
+	}
 
 	res->start = base;
 	res->end = base + size - 1;

arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts

@@ -46,6 +46,7 @@ &mmc0 {
 	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_cldo1>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
 	status = "okay";
 };
 
@@ -56,6 +57,7 @@ &mmc2 {
 	vqmmc-supply = <&reg_bldo2>;
 	non-removable;
 	cap-mmc-hw-reset;
+	bus-width = <8>;
 	status = "okay";
 };
 

arch/arm64/configs/defconfig

@@ -38,6 +38,7 @@ CONFIG_ARCH_BCM_IPROC=y
 CONFIG_ARCH_BERLIN=y
 CONFIG_ARCH_BRCMSTB=y
 CONFIG_ARCH_EXYNOS=y
+CONFIG_ARCH_K3=y
 CONFIG_ARCH_LAYERSCAPE=y
 CONFIG_ARCH_LG1K=y
 CONFIG_ARCH_HISI=y
@@ -605,6 +606,8 @@ CONFIG_ARCH_TEGRA_132_SOC=y
 CONFIG_ARCH_TEGRA_210_SOC=y
 CONFIG_ARCH_TEGRA_186_SOC=y
 CONFIG_ARCH_TEGRA_194_SOC=y
+CONFIG_ARCH_K3_AM6_SOC=y
+CONFIG_SOC_TI=y
 CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
 CONFIG_EXTCON_USB_GPIO=y
 CONFIG_EXTCON_USBC_CROS_EC=y

drivers/bus/ti-sysc.c

@@ -498,32 +498,29 @@ static int sysc_check_registers(struct sysc *ddata)
 
 /**
  * syc_ioremap - ioremap register space for the interconnect target module
- * @ddata: deviec driver data
+ * @ddata: device driver data
  *
  * Note that the interconnect target module registers can be anywhere
- * within the first child device address space. For example, SGX has
- * them at offset 0x1fc00 in the 32MB module address space. We just
- * what we need around the interconnect target module registers.
+ * within the interconnect target module range. For example, SGX has
+ * them at offset 0x1fc00 in the 32MB module address space. And cpsw
+ * has them at offset 0x1200 in the CPSW_WR child. Usually the
+ * the interconnect target module registers are at the beginning of
+ * the module range though.
  */
 static int sysc_ioremap(struct sysc *ddata)
 {
-	u32 size = 0;
-
-	if (ddata->offsets[SYSC_SYSSTATUS] >= 0)
-		size = ddata->offsets[SYSC_SYSSTATUS];
-	else if (ddata->offsets[SYSC_SYSCONFIG] >= 0)
-		size = ddata->offsets[SYSC_SYSCONFIG];
-	else if (ddata->offsets[SYSC_REVISION] >= 0)
-		size = ddata->offsets[SYSC_REVISION];
-	else
-		return -EINVAL;
+	int size;
 
-	size &= 0xfff00;
-	size += SZ_256;
+	size = max3(ddata->offsets[SYSC_REVISION],
+		    ddata->offsets[SYSC_SYSCONFIG],
+		    ddata->offsets[SYSC_SYSSTATUS]);
+
+	if (size < 0 || (size + sizeof(u32)) > ddata->module_size)
+		return -EINVAL;
 
 	ddata->module_va = devm_ioremap(ddata->dev,
 					ddata->module_pa,
-					size);
+					size + sizeof(u32));
 	if (!ddata->module_va)
 		return -EIO;
 
@@ -1224,10 +1221,10 @@ static int sysc_child_suspend_noirq(struct device *dev)
 	if (!pm_runtime_status_suspended(dev)) {
 		error = pm_generic_runtime_suspend(dev);
 		if (error) {
-			dev_err(dev, "%s error at %i: %i\n",
-				__func__, __LINE__, error);
+			dev_warn(dev, "%s busy at %i: %i\n",
+				 __func__, __LINE__, error);
 
-			return error;
+			return 0;
 		}
 
 		error = sysc_runtime_suspend(ddata->dev);

drivers/firmware/arm_scmi/perf.c

@@ -166,7 +166,13 @@ scmi_perf_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
 					le32_to_cpu(attr->sustained_freq_khz);
 		dom_info->sustained_perf_level =
 					le32_to_cpu(attr->sustained_perf_level);
-		dom_info->mult_factor =	(dom_info->sustained_freq_khz * 1000) /
+		if (!dom_info->sustained_freq_khz ||
+		    !dom_info->sustained_perf_level)
+			/* CPUFreq converts to kHz, hence default 1000 */
+			dom_info->mult_factor =	1000;
+		else
+			dom_info->mult_factor =
+					(dom_info->sustained_freq_khz * 1000) /
 					dom_info->sustained_perf_level;
 		memcpy(dom_info->name, attr->name, SCMI_MAX_STR_SIZE);
 	}

drivers/hwmon/raspberrypi-hwmon.c

@@ -164,3 +164,4 @@ module_platform_driver(rpi_hwmon_driver);
 MODULE_AUTHOR("Stefan Wahren <stefan.wahren@i2se.com>");
 MODULE_DESCRIPTION("Raspberry Pi voltage sensor driver");
 MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:raspberrypi-hwmon");

drivers/memory/ti-aemif.c

@@ -411,7 +411,7 @@ static int aemif_probe(struct platform_device *pdev)
 			if (ret < 0)
 				goto error;
 		}
-	} else {
+	} else if (pdata) {
 		for (i = 0; i < pdata->num_sub_devices; i++) {
 			pdata->sub_devices[i].dev.parent = dev;
 			ret = platform_device_register(&pdata->sub_devices[i]);

drivers/soc/fsl/qbman/bman_ccsr.c

@@ -120,6 +120,7 @@ static void bm_set_memory(u64 ba, u32 size)
  */
 static dma_addr_t fbpr_a;
 static size_t fbpr_sz;
+static int __bman_probed;
 
 static int bman_fbpr(struct reserved_mem *rmem)
 {
@@ -166,6 +167,12 @@ static irqreturn_t bman_isr(int irq, void *ptr)
 	return IRQ_HANDLED;
 }
 
+int bman_is_probed(void)
+{
+	return __bman_probed;
+}
+EXPORT_SYMBOL_GPL(bman_is_probed);
+
 static int fsl_bman_probe(struct platform_device *pdev)
 {
 	int ret, err_irq;
@@ -175,6 +182,8 @@ static int fsl_bman_probe(struct platform_device *pdev)
 	u16 id, bm_pool_cnt;
 	u8 major, minor;
 
+	__bman_probed = -1;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
 		dev_err(dev, "Can't get %pOF property 'IORESOURCE_MEM'\n",
@@ -255,6 +264,8 @@ static int fsl_bman_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	__bman_probed = 1;
+
 	return 0;
 };
 

drivers/soc/fsl/qbman/qman.c

@@ -2729,6 +2729,9 @@ static int qman_alloc_range(struct gen_pool *p, u32 *result, u32 cnt)
 {
 	unsigned long addr;
 
+	if (!p)
+		return -ENODEV;
+
 	addr = gen_pool_alloc(p, cnt);
 	if (!addr)
 		return -ENOMEM;

drivers/soc/fsl/qbman/qman_ccsr.c

@@ -273,6 +273,7 @@ static const struct qman_error_info_mdata error_mdata[] = {
 static u32 __iomem *qm_ccsr_start;
 /* A SDQCR mask comprising all the available/visible pool channels */
 static u32 qm_pools_sdqcr;
+static int __qman_probed;
 
 static inline u32 qm_ccsr_in(u32 offset)
 {
@@ -686,6 +687,12 @@ static int qman_resource_init(struct device *dev)
 	return 0;
 }
 
+int qman_is_probed(void)
+{
+	return __qman_probed;
+}
+EXPORT_SYMBOL_GPL(qman_is_probed);
+
 static int fsl_qman_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -695,6 +702,8 @@ static int fsl_qman_probe(struct platform_device *pdev)
 	u16 id;
 	u8 major, minor;
 
+	__qman_probed = -1;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
 		dev_err(dev, "Can't get %pOF property 'IORESOURCE_MEM'\n",
@@ -828,6 +837,8 @@ static int fsl_qman_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
+	__qman_probed = 1;
+
 	return 0;
 }
 

drivers/soc/fsl/qbman/qman_portal.c

@@ -227,6 +227,14 @@ static int qman_portal_probe(struct platform_device *pdev)
 	int irq, cpu, err;
 	u32 val;
 
+	err = qman_is_probed();
+	if (!err)
+		return -EPROBE_DEFER;
+	if (err < 0) {
+		dev_err(&pdev->dev, "failing probe due to qman probe error\n");
+		return -ENODEV;
+	}
+
 	pcfg = devm_kmalloc(dev, sizeof(*pcfg), GFP_KERNEL);
 	if (!pcfg)
 		return -ENOMEM;

drivers/soc/fsl/qe/ucc.c

@@ -626,7 +626,7 @@ static u32 ucc_get_tdm_sync_shift(enum comm_dir mode, u32 tdm_num)
 {
 	u32 shift;
 
-	shift = (mode == COMM_DIR_RX) ? RX_SYNC_SHIFT_BASE : RX_SYNC_SHIFT_BASE;
+	shift = (mode == COMM_DIR_RX) ? RX_SYNC_SHIFT_BASE : TX_SYNC_SHIFT_BASE;
 	shift -= tdm_num * 2;
 
 	return shift;

include/soc/fsl/bman.h

@@ -126,4 +126,12 @@ int bman_release(struct bman_pool *pool, const struct bm_buffer *bufs, u8 num);
  */
 int bman_acquire(struct bman_pool *pool, struct bm_buffer *bufs, u8 num);
 
+/**
+ * bman_is_probed - Check if bman is probed
+ *
+ * Returns 1 if the bman driver successfully probed, -1 if the bman driver
+ * failed to probe or 0 if the bman driver did not probed yet.
+ */
+int bman_is_probed(void);
+
 #endif	/* __FSL_BMAN_H */

include/soc/fsl/qman.h

@@ -1186,4 +1186,12 @@ int qman_alloc_cgrid_range(u32 *result, u32 count);
  */
 int qman_release_cgrid(u32 id);
 
+/**
+ * qman_is_probed - Check if qman is probed
+ *
+ * Returns 1 if the qman driver successfully probed, -1 if the qman driver
+ * failed to probe or 0 if the qman driver did not probed yet.
+ */
+int qman_is_probed(void);
+
 #endif	/* __FSL_QMAN_H */