Merge branches 'next/pinctrl-samsung' and 'next/board-samsung' into next/dt-samsung-new

Conflicts:
	arch/arm/mach-exynos/mach-smdkv310.c

Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt

+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+- interrupts: interrupt specifier for the controller. The format and value of
+  the interrupt specifier depends on the interrupt parent for the controller.
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be atleast one
+  child node and there is no limit on the count of these child nodes.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be atleast one pin specfied for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include atleast a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+- interrupt-controller: identifies the controller node as interrupt-parent.
+- #interrupt-cells: the value of this property should be 2.
+  - First Cell: represents the external gpio interrupt number local to the
+    external gpio interrupt space of the controller.
+  - Second Cell: flags to identify the type of the interrupt
+    - 1 = rising edge triggered
+    - 2 = falling edge triggered
+    - 3 = rising and falling edge triggered
+    - 4 = high level triggered
+    - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node. This child node should include
+   the following properties.
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 SoC.
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Example 1: A pin-controller node with pin groups.
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+	uart@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+		pinctrl-names = "default", "flow-control;
+		pinctrl-0 = <&uart0_data>;
+		pinctrl-1 = <&uart0_data &uart0_fctl>;
+	};
+
+Example 4: Set up the default pin state for uart controller.
+
+	static int s3c24xx_serial_probe(struct platform_device *pdev) {
+		struct pinctrl *pinctrl;
+		...
+		...
+		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	}

arch/arm/boot/dts/exynos4210-origen.dts

@@ -62,35 +62,43 @@ gpio_keys {
 
 		up {
 			label = "Up";
-			gpios = <&gpx2 0 0 0 2>;
+			gpios = <&gpx2 0 0 0x10000 2>;
 			linux,code = <103>;
 		};
 
 		down {
 			label = "Down";
-			gpios = <&gpx2 1 0 0 2>;
+			gpios = <&gpx2 1 0 0x10000 2>;
 			linux,code = <108>;
 		};
 
 		back {
 			label = "Back";
-			gpios = <&gpx1 7 0 0 2>;
+			gpios = <&gpx1 7 0 0x10000 2>;
 			linux,code = <158>;
 		};
 
 		home {
 			label = "Home";
-			gpios = <&gpx1 6 0 0 2>;
+			gpios = <&gpx1 6 0 0x10000 2>;
 			linux,code = <102>;
 		};
 
 		menu {
 			label = "Menu";
-			gpios = <&gpx1 5 0 0 2>;
+			gpios = <&gpx1 5 0 0x10000 2>;
 			linux,code = <139>;
 		};
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		status {
+			gpios = <&gpx1 3 0 0x10000 2>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
 	keypad@100A0000 {
 		status = "disabled";
 	};

arch/arm/boot/dts/exynos4210.dtsi

@@ -20,6 +20,7 @@
 */
 
 /include/ "skeleton.dtsi"
+/include/ "exynos4210-pinctrl.dtsi"
 
 / {
 	compatible = "samsung,exynos4210";
@@ -29,6 +30,9 @@ aliases {
 		spi0 = &spi_0;
 		spi1 = &spi_1;
 		spi2 = &spi_2;
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
 	};
 
 	gic:interrupt-controller@10490000 {
@@ -50,6 +54,39 @@ combiner:interrupt-controller@10440000 {
 			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
 	};
 
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+	pinctrl_2: pinctrl@03860000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x03860000 0x1000>;
+	};
+
 	watchdog@10060000 {
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x10060000 0x100>;

arch/arm/mach-exynos/Kconfig

@@ -221,6 +221,7 @@ config MACH_SMDKV310
 	select EXYNOS4_SETUP_KEYPAD
 	select EXYNOS4_SETUP_SDHCI
 	select EXYNOS4_SETUP_USB_PHY
+	select S3C24XX_PWM
 	help
 	  Machine support for Samsung SMDKV310
 
@@ -348,6 +349,7 @@ config MACH_ORIGEN
 	select EXYNOS4_SETUP_FIMD0
 	select EXYNOS4_SETUP_SDHCI
 	select EXYNOS4_SETUP_USB_PHY
+	select S3C24XX_PWM
 	help
 	  Machine support for ORIGEN based on Samsung EXYNOS4210
 
@@ -383,6 +385,7 @@ config MACH_SMDK4212
 	select EXYNOS4_SETUP_KEYPAD
 	select EXYNOS4_SETUP_SDHCI
 	select EXYNOS4_SETUP_USB_PHY
+	select S3C24XX_PWM
 	help
 	  Machine support for Samsung SMDK4212
 
@@ -405,6 +408,8 @@ config MACH_EXYNOS4_DT
 	select USE_OF
 	select ARM_AMBA
 	select HAVE_SAMSUNG_KEYPAD if INPUT_KEYBOARD
+	select PINCTRL
+	select PINCTRL_EXYNOS4
 	help
 	  Machine support for Samsung Exynos4 machine with device tree enabled.
 	  Select this if a fdt blob is available for the Exynos4 SoC based board.

arch/arm/mach-exynos/common.c

@@ -980,6 +980,32 @@ static int __init exynos_init_irq_eint(void)
 {
 	int irq;
 
+#ifdef CONFIG_PINCTRL_SAMSUNG
+	/*
+	 * The Samsung pinctrl driver provides an integrated gpio/pinmux/pinconf
+	 * functionality along with support for external gpio and wakeup
+	 * interrupts. If the samsung pinctrl driver is enabled and includes
+	 * the wakeup interrupt support, then the setting up external wakeup
+	 * interrupts here can be skipped. This check here is temporary to
+	 * allow exynos4 platforms that do not use Samsung pinctrl driver to
+	 * co-exist with platforms that do. When all of the Samsung Exynos4
+	 * platforms switch over to using the pinctrl driver, the wakeup
+	 * interrupt support code here can be completely removed.
+	 */
+	struct device_node *pctrl_np, *wkup_np;
+	const char *pctrl_compat = "samsung,pinctrl-exynos4210";
+	const char *wkup_compat = "samsung,exynos4210-wakeup-eint";
+
+	for_each_compatible_node(pctrl_np, NULL, pctrl_compat) {
+		if (of_device_is_available(pctrl_np)) {
+			wkup_np = of_find_compatible_node(pctrl_np, NULL,
+							wkup_compat);
+			if (wkup_np)
+				return -ENODEV;
+		}
+	}
+#endif
+
 	if (soc_is_exynos5250())
 		exynos_eint_base = ioremap(EXYNOS5_PA_GPIO1, SZ_4K);
 	else

arch/arm/mach-exynos/mach-origen.c

@@ -15,6 +15,7 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/input.h>
+#include <linux/pwm.h>
 #include <linux/pwm_backlight.h>
 #include <linux/gpio_keys.h>
 #include <linux/i2c.h>
@@ -614,6 +615,10 @@ static struct platform_device origen_lcd_hv070wsa = {
 	.dev.platform_data	= &origen_lcd_hv070wsa_data,
 };
 
+static struct pwm_lookup origen_pwm_lookup[] = {
+	PWM_LOOKUP("s3c24xx-pwm.0", 0, "pwm-backlight.0", NULL),
+};
+
 #ifdef CONFIG_DRM_EXYNOS
 static struct exynos_drm_fimd_pdata drm_fimd_pdata = {
 	.panel	= {
@@ -798,6 +803,7 @@ static void __init origen_machine_init(void)
 
 	platform_add_devices(origen_devices, ARRAY_SIZE(origen_devices));
 
+	pwm_add_table(origen_pwm_lookup, ARRAY_SIZE(origen_pwm_lookup));
 	samsung_bl_set(&origen_bl_gpio_info, &origen_bl_data);
 
 	origen_bt_setup();

arch/arm/mach-exynos/mach-smdk4x12.c

@@ -17,6 +17,7 @@
 #include <linux/mfd/max8997.h>
 #include <linux/mmc/host.h>
 #include <linux/platform_device.h>
+#include <linux/pwm.h>
 #include <linux/pwm_backlight.h>
 #include <linux/regulator/machine.h>
 #include <linux/serial_core.h>
@@ -222,6 +223,10 @@ static struct platform_pwm_backlight_data smdk4x12_bl_data = {
 	.pwm_period_ns  = 1000,
 };
 
+static struct pwm_lookup smdk4x12_pwm_lookup[] = {
+	PWM_LOOKUP("s3c24xx-pwm.1", 0, "pwm-backlight.0", NULL),
+};
+
 static uint32_t smdk4x12_keymap[] __initdata = {
 	/* KEY(row, col, keycode) */
 	KEY(1, 3, KEY_1), KEY(1, 4, KEY_2), KEY(1, 5, KEY_3),
@@ -349,6 +354,7 @@ static void __init smdk4x12_machine_init(void)
 				ARRAY_SIZE(smdk4x12_i2c_devs7));
 
 	samsung_bl_set(&smdk4x12_bl_gpio_info, &smdk4x12_bl_data);
+	pwm_add_table(smdk4x12_pwm_lookup, ARRAY_SIZE(smdk4x12_pwm_lookup));
 
 	samsung_keypad_set_platdata(&smdk4x12_keypad_data);
 

arch/arm/mach-exynos/mach-smdkv310.c

@@ -18,6 +18,7 @@
 #include <linux/io.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
+#include <linux/pwm.h>
 #include <linux/pwm_backlight.h>
 #include <linux/platform_data/s3c-hsotg.h>
 
@@ -360,6 +361,10 @@ static struct i2c_board_info hdmiphy_info = {
 	I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
 };
 
+static struct pwm_lookup smdkv310_pwm_lookup[] = {
+	PWM_LOOKUP("s3c24xx-pwm.1", 0, "pwm-backlight.0", NULL),
+};
+
 static void s5p_tv_setup(void)
 {
 	/* direct HPD to HDMI chip */
@@ -399,6 +404,8 @@ static void __init smdkv310_machine_init(void)
 	samsung_keypad_set_platdata(&smdkv310_keypad_data);
 
 	samsung_bl_set(&smdkv310_bl_gpio_info, &smdkv310_bl_data);
+	pwm_add_table(smdkv310_pwm_lookup, ARRAY_SIZE(smdkv310_pwm_lookup));
+
 #ifdef CONFIG_DRM_EXYNOS
 	s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
 	exynos4_fimd0_gpio_setup_24bpp();

arch/arm/mach-s3c64xx/mach-crag6410-module.c

@@ -16,6 +16,7 @@
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
 #include <linux/mfd/wm8994/pdata.h>
+#include <linux/mfd/arizona/pdata.h>
 
 #include <linux/regulator/machine.h>
 
@@ -181,9 +182,33 @@ static const struct i2c_board_info wm1277_devs[] = {
 	},
 };
 
-static const struct i2c_board_info wm5102_devs[] = {
-	{ I2C_BOARD_INFO("wm5102", 0x1a),
-	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2, },
+static struct arizona_pdata wm5102_pdata = {
+	.ldoena = S3C64XX_GPN(7),
+	.gpio_base = CODEC_GPIO_BASE,
+	.irq_active_high = true,
+	.micd_pol_gpio = CODEC_GPIO_BASE + 4,
+	.gpio_defaults = {
+		[2] = 0x10000, /* AIF3TXLRCLK */
+		[3] = 0x4,     /* OPCLK */
+	},
+};
+
+static struct s3c64xx_spi_csinfo wm5102_spi_csinfo = {
+	.line = S3C64XX_GPN(5),
+};
+
+static struct spi_board_info wm5102_spi_devs[] = {
+	[0] = {
+		.modalias	= "wm5102",
+		.max_speed_hz	= 10 * 1000 * 1000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+		.irq		= GLENFARCLAS_PMIC_IRQ_BASE +
+				  WM831X_IRQ_GPIO_2,
+		.controller_data = &wm5102_spi_csinfo,
+		.platform_data = &wm5102_pdata,
+	},
 };
 
 static const struct i2c_board_info wm6230_i2c_devs[] = {
@@ -223,8 +248,9 @@ static __devinitdata const struct {
 	{ .id = 0x3c, .name = "1273-EV1 Longmorn" },
 	{ .id = 0x3d, .name = "1277-EV1 Littlemill",
 	  .i2c_devs = wm1277_devs, .num_i2c_devs = ARRAY_SIZE(wm1277_devs) },
-	{ .id = 0x3e, .name = "WM5102-6271-EV1-CS127",
-	  .i2c_devs = wm5102_devs, .num_i2c_devs = ARRAY_SIZE(wm5102_devs) },
+	{ .id = 0x3e, .name = "WM5102-6271-EV1-CS127 Amrut",
+	  .spi_devs = wm5102_spi_devs,
+	  .num_spi_devs = ARRAY_SIZE(wm5102_spi_devs) },
 };
 
 static __devinit int wlf_gf_module_probe(struct i2c_client *i2c,

arch/arm/mach-s3c64xx/mach-crag6410.c

@@ -287,6 +287,16 @@ static struct platform_device littlemill_device = {
 	.id		= -1,
 };
 
+static struct platform_device bells_wm5102_device = {
+	.name		= "bells",
+	.id		= 0,
+};
+
+static struct platform_device bells_wm5110_device = {
+	.name		= "bells",
+	.id		= 1,
+};
+
 static struct regulator_consumer_supply wallvdd_consumers[] = {
 	REGULATOR_SUPPLY("SPKVDD", "1-001a"),
 	REGULATOR_SUPPLY("SPKVDD1", "1-001a"),
@@ -359,6 +369,8 @@ static struct platform_device *crag6410_devices[] __initdata = {
 	&tobermory_device,
 	&littlemill_device,
 	&lowland_device,
+	&bells_wm5102_device,
+	&bells_wm5110_device,
 	&wallvdd_device,
 };
 

drivers/gpio/gpio-samsung.c

@@ -2734,6 +2734,27 @@ static __init void exynos4_gpiolib_init(void)
 	int group = 0;
 	void __iomem *gpx_base;
 
+#ifdef CONFIG_PINCTRL_SAMSUNG
+		/*
+		 * This gpio driver includes support for device tree support and
+		 * there are platforms using it. In order to maintain
+		 * compatibility with those platforms, and to allow non-dt
+		 * Exynos4210 platforms to use this gpiolib support, a check
+		 * is added to find out if there is a active pin-controller
+		 * driver support available. If it is available, this gpiolib
+		 * support is ignored and the gpiolib support available in
+		 * pin-controller driver is used. This is a temporary check and
+		 * will go away when all of the Exynos4210 platforms have
+		 * switched to using device tree and the pin-ctrl driver.
+		 */
+		struct device_node *pctrl_np;
+		const char *pctrl_compat = "samsung,pinctrl-exynos4210";
+		pctrl_np = of_find_compatible_node(NULL, NULL, pctrl_compat);
+		if (pctrl_np)
+			if (of_device_is_available(pctrl_np))
+				return;
+#endif
+
 	/* gpio part1 */
 	gpio_base1 = ioremap(EXYNOS4_PA_GPIO1, SZ_4K);
 	if (gpio_base1 == NULL) {

drivers/pinctrl/Kconfig

@@ -145,6 +145,15 @@ config PINCTRL_COH901
 	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
 	  ports of 8 GPIO pins each.
 
+config PINCTRL_SAMSUNG
+	bool "Samsung pinctrl driver"
+	select PINMUX
+	select PINCONF
+
+config PINCTRL_EXYNOS4
+	bool "Pinctrl driver data for Exynos4 SoC"
+	select PINCTRL_SAMSUNG
+
 source "drivers/pinctrl/spear/Kconfig"
 
 endmenu

drivers/pinctrl/Makefile

@@ -29,5 +29,7 @@ obj-$(CONFIG_PINCTRL_TEGRA20)	+= pinctrl-tegra20.o
 obj-$(CONFIG_PINCTRL_TEGRA30)	+= pinctrl-tegra30.o
 obj-$(CONFIG_PINCTRL_U300)	+= pinctrl-u300.o
 obj-$(CONFIG_PINCTRL_COH901)	+= pinctrl-coh901.o
+obj-$(CONFIG_PINCTRL_SAMSUNG)	+= pinctrl-samsung.o
+obj-$(CONFIG_PINCTRL_EXYNOS4)	+= pinctrl-exynos.o
 
 obj-$(CONFIG_PLAT_SPEAR)	+= spear/

drivers/pinctrl/pinctrl-exynos.h

+/*
+ * Exynos specific definitions for Samsung pinctrl and gpiolib driver.
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2012 Linaro Ltd
+ *		http://www.linaro.org
+ *
+ * This file contains the Exynos specific definitions for the Samsung
+ * pinctrl/gpiolib interface drivers.
+ *
+ * Author: Thomas Abraham <thomas.ab@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#define EXYNOS_GPIO_START(__gpio)	((__gpio##_START) + (__gpio##_NR))
+
+#define EXYNOS4210_GPIO_A0_NR	(8)
+#define EXYNOS4210_GPIO_A1_NR	(6)
+#define EXYNOS4210_GPIO_B_NR	(8)
+#define EXYNOS4210_GPIO_C0_NR	(5)
+#define EXYNOS4210_GPIO_C1_NR	(5)
+#define EXYNOS4210_GPIO_D0_NR	(4)
+#define EXYNOS4210_GPIO_D1_NR	(4)
+#define EXYNOS4210_GPIO_E0_NR	(5)
+#define EXYNOS4210_GPIO_E1_NR	(8)
+#define EXYNOS4210_GPIO_E2_NR	(6)
+#define EXYNOS4210_GPIO_E3_NR	(8)
+#define EXYNOS4210_GPIO_E4_NR	(8)
+#define EXYNOS4210_GPIO_F0_NR	(8)
+#define EXYNOS4210_GPIO_F1_NR	(8)
+#define EXYNOS4210_GPIO_F2_NR	(8)
+#define EXYNOS4210_GPIO_F3_NR	(6)
+#define EXYNOS4210_GPIO_J0_NR	(8)
+#define EXYNOS4210_GPIO_J1_NR	(5)
+#define EXYNOS4210_GPIO_K0_NR	(7)
+#define EXYNOS4210_GPIO_K1_NR	(7)
+#define EXYNOS4210_GPIO_K2_NR	(7)
+#define EXYNOS4210_GPIO_K3_NR	(7)
+#define EXYNOS4210_GPIO_L0_NR	(8)
+#define EXYNOS4210_GPIO_L1_NR	(3)
+#define EXYNOS4210_GPIO_L2_NR	(8)
+#define EXYNOS4210_GPIO_Y0_NR	(6)
+#define EXYNOS4210_GPIO_Y1_NR	(4)
+#define EXYNOS4210_GPIO_Y2_NR	(6)
+#define EXYNOS4210_GPIO_Y3_NR	(8)
+#define EXYNOS4210_GPIO_Y4_NR	(8)
+#define EXYNOS4210_GPIO_Y5_NR	(8)
+#define EXYNOS4210_GPIO_Y6_NR	(8)
+#define EXYNOS4210_GPIO_X0_NR	(8)
+#define EXYNOS4210_GPIO_X1_NR	(8)
+#define EXYNOS4210_GPIO_X2_NR	(8)
+#define EXYNOS4210_GPIO_X3_NR	(8)
+#define EXYNOS4210_GPIO_Z_NR	(7)
+
+enum exynos4210_gpio_xa_start {
+	EXYNOS4210_GPIO_A0_START	= 0,
+	EXYNOS4210_GPIO_A1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_A0),
+	EXYNOS4210_GPIO_B_START		= EXYNOS_GPIO_START(EXYNOS4210_GPIO_A1),
+	EXYNOS4210_GPIO_C0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_B),
+	EXYNOS4210_GPIO_C1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_C0),
+	EXYNOS4210_GPIO_D0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_C1),
+	EXYNOS4210_GPIO_D1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_D0),
+	EXYNOS4210_GPIO_E0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_D1),
+	EXYNOS4210_GPIO_E1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E0),
+	EXYNOS4210_GPIO_E2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E1),
+	EXYNOS4210_GPIO_E3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E2),
+	EXYNOS4210_GPIO_E4_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E3),
+	EXYNOS4210_GPIO_F0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_E4),
+	EXYNOS4210_GPIO_F1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_F0),
+	EXYNOS4210_GPIO_F2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_F1),
+	EXYNOS4210_GPIO_F3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_F2),
+};
+
+enum exynos4210_gpio_xb_start {
+	EXYNOS4210_GPIO_J0_START	= 0,
+	EXYNOS4210_GPIO_J1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_J0),
+	EXYNOS4210_GPIO_K0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_J1),
+	EXYNOS4210_GPIO_K1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K0),
+	EXYNOS4210_GPIO_K2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K1),
+	EXYNOS4210_GPIO_K3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K2),
+	EXYNOS4210_GPIO_L0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_K3),
+	EXYNOS4210_GPIO_L1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_L0),
+	EXYNOS4210_GPIO_L2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_L1),
+	EXYNOS4210_GPIO_Y0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_L2),
+	EXYNOS4210_GPIO_Y1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y0),
+	EXYNOS4210_GPIO_Y2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y1),
+	EXYNOS4210_GPIO_Y3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y2),
+	EXYNOS4210_GPIO_Y4_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y3),
+	EXYNOS4210_GPIO_Y5_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y4),
+	EXYNOS4210_GPIO_Y6_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y5),
+	EXYNOS4210_GPIO_X0_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_Y6),
+	EXYNOS4210_GPIO_X1_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_X0),
+	EXYNOS4210_GPIO_X2_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_X1),
+	EXYNOS4210_GPIO_X3_START	= EXYNOS_GPIO_START(EXYNOS4210_GPIO_X2),
+};
+
+enum exynos4210_gpio_xc_start {
+	EXYNOS4210_GPIO_Z_START		= 0,
+};
+
+#define	EXYNOS4210_GPIO_A0_IRQ		EXYNOS4210_GPIO_A0_START
+#define	EXYNOS4210_GPIO_A1_IRQ		EXYNOS4210_GPIO_A1_START
+#define	EXYNOS4210_GPIO_B_IRQ		EXYNOS4210_GPIO_B_START
+#define	EXYNOS4210_GPIO_C0_IRQ		EXYNOS4210_GPIO_C0_START
+#define	EXYNOS4210_GPIO_C1_IRQ		EXYNOS4210_GPIO_C1_START
+#define	EXYNOS4210_GPIO_D0_IRQ		EXYNOS4210_GPIO_D0_START
+#define	EXYNOS4210_GPIO_D1_IRQ		EXYNOS4210_GPIO_D1_START
+#define	EXYNOS4210_GPIO_E0_IRQ		EXYNOS4210_GPIO_E0_START
+#define	EXYNOS4210_GPIO_E1_IRQ		EXYNOS4210_GPIO_E1_START
+#define	EXYNOS4210_GPIO_E2_IRQ		EXYNOS4210_GPIO_E2_START
+#define	EXYNOS4210_GPIO_E3_IRQ		EXYNOS4210_GPIO_E3_START
+#define	EXYNOS4210_GPIO_E4_IRQ		EXYNOS4210_GPIO_E4_START
+#define	EXYNOS4210_GPIO_F0_IRQ		EXYNOS4210_GPIO_F0_START
+#define	EXYNOS4210_GPIO_F1_IRQ		EXYNOS4210_GPIO_F1_START
+#define	EXYNOS4210_GPIO_F2_IRQ		EXYNOS4210_GPIO_F2_START
+#define	EXYNOS4210_GPIO_F3_IRQ		EXYNOS4210_GPIO_F3_START
+#define	EXYNOS4210_GPIO_J0_IRQ		EXYNOS4210_GPIO_J0_START
+#define	EXYNOS4210_GPIO_J1_IRQ		EXYNOS4210_GPIO_J1_START
+#define	EXYNOS4210_GPIO_K0_IRQ		EXYNOS4210_GPIO_K0_START
+#define	EXYNOS4210_GPIO_K1_IRQ		EXYNOS4210_GPIO_K1_START
+#define	EXYNOS4210_GPIO_K2_IRQ		EXYNOS4210_GPIO_K2_START
+#define	EXYNOS4210_GPIO_K3_IRQ		EXYNOS4210_GPIO_K3_START
+#define	EXYNOS4210_GPIO_L0_IRQ		EXYNOS4210_GPIO_L0_START
+#define	EXYNOS4210_GPIO_L1_IRQ		EXYNOS4210_GPIO_L1_START
+#define	EXYNOS4210_GPIO_L2_IRQ		EXYNOS4210_GPIO_L2_START
+#define	EXYNOS4210_GPIO_Z_IRQ		EXYNOS4210_GPIO_Z_START
+
+#define EXYNOS4210_GPIOA_NR_PINS	EXYNOS_GPIO_START(EXYNOS4210_GPIO_F3)
+#define EXYNOS4210_GPIOA_NR_GINT	EXYNOS_GPIO_START(EXYNOS4210_GPIO_F3)
+#define EXYNOS4210_GPIOB_NR_PINS	EXYNOS_GPIO_START(EXYNOS4210_GPIO_X3)
+#define EXYNOS4210_GPIOB_NR_GINT	EXYNOS_GPIO_START(EXYNOS4210_GPIO_L2)
+#define EXYNOS4210_GPIOC_NR_PINS	EXYNOS_GPIO_START(EXYNOS4210_GPIO_Z)
+
+/* External GPIO and wakeup interrupt related definitions */
+#define EXYNOS_GPIO_ECON_OFFSET		0x700
+#define EXYNOS_GPIO_EMASK_OFFSET	0x900
+#define EXYNOS_GPIO_EPEND_OFFSET	0xA00
+#define EXYNOS_WKUP_ECON_OFFSET		0xE00
+#define EXYNOS_WKUP_EMASK_OFFSET	0xF00
+#define EXYNOS_WKUP_EPEND_OFFSET	0xF40
+#define EXYNOS_SVC_OFFSET		0xB08
+
+/* helpers to access interrupt service register */
+#define EXYNOS_SVC_GROUP_SHIFT		3
+#define EXYNOS_SVC_GROUP_MASK		0x1f
+#define EXYNOS_SVC_NUM_MASK		7
+#define EXYNOS_SVC_GROUP(x)		((x >> EXYNOS_SVC_GROUP_SHIFT) & \
+						EXYNOS_SVC_GROUP_MASK)
+
+/* Exynos specific external interrupt trigger types */
+#define EXYNOS_EINT_LEVEL_LOW		0
+#define EXYNOS_EINT_LEVEL_HIGH		1
+#define EXYNOS_EINT_EDGE_FALLING	2
+#define EXYNOS_EINT_EDGE_RISING		3
+#define EXYNOS_EINT_EDGE_BOTH		4
+#define EXYNOS_EINT_CON_MASK		0xF
+#define EXYNOS_EINT_CON_LEN		4
+
+#define EXYNOS_EINT_MAX_PER_BANK	8
+#define EXYNOS_EINT_NR_WKUP_EINT
+
+#define EXYNOS_PIN_BANK_EINTN(reg, __gpio, id)		\
+	{						\
+		.pctl_offset	= reg,			\
+		.pin_base	= (__gpio##_START),	\
+		.nr_pins	= (__gpio##_NR),	\
+		.func_width	= 4,			\
+		.pud_width	= 2,			\
+		.drv_width	= 2,			\
+		.conpdn_width	= 2,			\
+		.pudpdn_width	= 2,			\
+		.eint_type	= EINT_TYPE_NONE,	\
+		.name		= id			\
+	}
+
+#define EXYNOS_PIN_BANK_EINTG(reg, __gpio, id)		\
+	{						\
+		.pctl_offset	= reg,			\
+		.pin_base	= (__gpio##_START),	\
+		.nr_pins	= (__gpio##_NR),	\
+		.func_width	= 4,			\
+		.pud_width	= 2,			\
+		.drv_width	= 2,			\
+		.conpdn_width	= 2,			\
+		.pudpdn_width	= 2,			\
+		.eint_type	= EINT_TYPE_GPIO,	\
+		.irq_base	= (__gpio##_IRQ),	\
+		.name		= id			\
+	}
+
+/**
+ * struct exynos_geint_data: gpio eint specific data for irq_chip callbacks.
+ * @bank: pin bank from which this gpio interrupt originates.
+ * @pin: pin number within the bank.
+ * @eint_offset: offset to be added to the con/pend/mask register bank base.
+ */
+struct exynos_geint_data {
+	struct samsung_pin_bank	*bank;
+	u32			pin;
+	u32			eint_offset;
+};
+
+/**
+ * struct exynos_weint_data: irq specific data for all the wakeup interrupts
+ * generated by the external wakeup interrupt controller.
+ * @domain: irq domain representing the external wakeup interrupts
+ * @irq: interrupt number within the domain.
+ */
+struct exynos_weint_data {
+	struct irq_domain	*domain;
+	u32			irq;
+};

drivers/pinctrl/pinctrl-samsung.h

+/*
+ * pin-controller/pin-mux/pin-config/gpio-driver for Samsung's SoC's.
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2012 Linaro Ltd
+ *		http://www.linaro.org
+ *
+ * Author: Thomas Abraham <thomas.ab@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __PINCTRL_SAMSUNG_H
+#define __PINCTRL_SAMSUNG_H
+
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/machine.h>
+
+/* register offsets within a pin bank */
+#define DAT_REG		0x4
+#define PUD_REG		0x8
+#define DRV_REG		0xC
+#define CONPDN_REG	0x10
+#define PUDPDN_REG	0x14
+
+/* pinmux function number for pin as gpio output line */
+#define FUNC_OUTPUT	0x1
+
+/**
+ * enum pincfg_type - possible pin configuration types supported.
+ * @PINCFG_TYPE_PUD: Pull up/down configuration.
+ * @PINCFG_TYPE_DRV: Drive strength configuration.
+ * @PINCFG_TYPE_CON_PDN: Pin function in power down mode.
+ * @PINCFG_TYPE_PUD_PDN: Pull up/down configuration in power down mode.
+ */
+enum pincfg_type {
+	PINCFG_TYPE_PUD,
+	PINCFG_TYPE_DRV,
+	PINCFG_TYPE_CON_PDN,
+	PINCFG_TYPE_PUD_PDN,
+};
+
+/*
+ * pin configuration (pull up/down and drive strength) type and its value are
+ * packed together into a 16-bits. The upper 8-bits represent the configuration
+ * type and the lower 8-bits hold the value of the configuration type.
+ */
+#define PINCFG_TYPE_MASK		0xFF
+#define PINCFG_VALUE_SHIFT		8
+#define PINCFG_VALUE_MASK		(0xFF << PINCFG_VALUE_SHIFT)
+#define PINCFG_PACK(type, value)	(((value) << PINCFG_VALUE_SHIFT) | type)
+#define PINCFG_UNPACK_TYPE(cfg)		((cfg) & PINCFG_TYPE_MASK)
+#define PINCFG_UNPACK_VALUE(cfg)	(((cfg) & PINCFG_VALUE_MASK) >> \
+						PINCFG_VALUE_SHIFT)
+/**
+ * enum eint_type - possible external interrupt types.
+ * @EINT_TYPE_NONE: bank does not support external interrupts
+ * @EINT_TYPE_GPIO: bank supportes external gpio interrupts
+ * @EINT_TYPE_WKUP: bank supportes external wakeup interrupts
+ *
+ * Samsung GPIO controller groups all the available pins into banks. The pins
+ * in a pin bank can support external gpio interrupts or external wakeup
+ * interrupts or no interrupts at all. From a software perspective, the only
+ * difference between external gpio and external wakeup interrupts is that
+ * the wakeup interrupts can additionally wakeup the system if it is in
+ * suspended state.
+ */
+enum eint_type {
+	EINT_TYPE_NONE,
+	EINT_TYPE_GPIO,
+	EINT_TYPE_WKUP,
+};
+
+/* maximum length of a pin in pin descriptor (example: "gpa0-0") */
+#define PIN_NAME_LENGTH	10
+
+#define PIN_GROUP(n, p, f)				\
+	{						\
+		.name		= n,			\
+		.pins		= p,			\
+		.num_pins	= ARRAY_SIZE(p),	\
+		.func		= f			\
+	}
+
+#define PMX_FUNC(n, g)					\
+	{						\
+		.name		= n,			\
+		.groups		= g,			\
+		.num_groups	= ARRAY_SIZE(g),	\
+	}
+
+struct samsung_pinctrl_drv_data;
+
+/**
+ * struct samsung_pin_bank: represent a controller pin-bank.
+ * @reg_offset: starting offset of the pin-bank registers.
+ * @pin_base: starting pin number of the bank.
+ * @nr_pins: number of pins included in this bank.
+ * @func_width: width of the function selector bit field.
+ * @pud_width: width of the pin pull up/down selector bit field.
+ * @drv_width: width of the pin driver strength selector bit field.
+ * @conpdn_width: width of the sleep mode function selector bin field.
+ * @pudpdn_width: width of the sleep mode pull up/down selector bit field.
+ * @eint_type: type of the external interrupt supported by the bank.
+ * @irq_base: starting controller local irq number of the bank.
+ * @name: name to be prefixed for each pin in this pin bank.
+ */
+struct samsung_pin_bank {
+	u32		pctl_offset;
+	u32		pin_base;
+	u8		nr_pins;
+	u8		func_width;
+	u8		pud_width;
+	u8		drv_width;
+	u8		conpdn_width;
+	u8		pudpdn_width;
+	enum eint_type	eint_type;
+	u32		irq_base;
+	char		*name;
+};
+
+/**
+ * struct samsung_pin_ctrl: represent a pin controller.
+ * @pin_banks: list of pin banks included in this controller.
+ * @nr_banks: number of pin banks.
+ * @base: starting system wide pin number.
+ * @nr_pins: number of pins supported by the controller.
+ * @nr_gint: number of external gpio interrupts supported.
+ * @nr_wint: number of external wakeup interrupts supported.
+ * @geint_con: offset of the ext-gpio controller registers.
+ * @geint_mask: offset of the ext-gpio interrupt mask registers.
+ * @geint_pend: offset of the ext-gpio interrupt pending registers.
+ * @weint_con: offset of the ext-wakeup controller registers.
+ * @weint_mask: offset of the ext-wakeup interrupt mask registers.
+ * @weint_pend: offset of the ext-wakeup interrupt pending registers.
+ * @svc: offset of the interrupt service register.
+ * @eint_gpio_init: platform specific callback to setup the external gpio
+ *	interrupts for the controller.
+ * @eint_wkup_init: platform specific callback to setup the external wakeup
+ *	interrupts for the controller.
+ * @label: for debug information.
+ */
+struct samsung_pin_ctrl {
+	struct samsung_pin_bank	*pin_banks;
+	u32		nr_banks;
+
+	u32		base;
+	u32		nr_pins;
+	u32		nr_gint;
+	u32		nr_wint;
+
+	u32		geint_con;
+	u32		geint_mask;
+	u32		geint_pend;
+
+	u32		weint_con;
+	u32		weint_mask;
+	u32		weint_pend;
+
+	u32		svc;
+
+	int		(*eint_gpio_init)(struct samsung_pinctrl_drv_data *);
+	int		(*eint_wkup_init)(struct samsung_pinctrl_drv_data *);
+	char		*label;
+};
+
+/**
+ * struct samsung_pinctrl_drv_data: wrapper for holding driver data together.
+ * @virt_base: register base address of the controller.
+ * @dev: device instance representing the controller.
+ * @irq: interrpt number used by the controller to notify gpio interrupts.
+ * @ctrl: pin controller instance managed by the driver.
+ * @pctl: pin controller descriptor registered with the pinctrl subsystem.
+ * @pctl_dev: cookie representing pinctrl device instance.
+ * @pin_groups: list of pin groups available to the driver.
+ * @nr_groups: number of such pin groups.
+ * @pmx_functions: list of pin functions available to the driver.
+ * @nr_function: number of such pin functions.
+ * @gc: gpio_chip instance registered with gpiolib.
+ * @grange: linux gpio pin range supported by this controller.
+ */
+struct samsung_pinctrl_drv_data {
+	void __iomem			*virt_base;
+	struct device			*dev;
+	int				irq;
+
+	struct samsung_pin_ctrl		*ctrl;
+	struct pinctrl_desc		pctl;
+	struct pinctrl_dev		*pctl_dev;
+
+	const struct samsung_pin_group	*pin_groups;
+	unsigned int			nr_groups;
+	const struct samsung_pmx_func	*pmx_functions;
+	unsigned int			nr_functions;
+
+	struct irq_domain		*gpio_irqd;
+	struct irq_domain		*wkup_irqd;
+
+	struct gpio_chip		*gc;
+	struct pinctrl_gpio_range	grange;
+};
+
+/**
+ * struct samsung_pin_group: represent group of pins of a pinmux function.
+ * @name: name of the pin group, used to lookup the group.
+ * @pins: the pins included in this group.
+ * @num_pins: number of pins included in this group.
+ * @func: the function number to be programmed when selected.
+ */
+struct samsung_pin_group {
+	const char		*name;
+	const unsigned int	*pins;
+	u8			num_pins;
+	u8			func;
+};
+
+/**
+ * struct samsung_pmx_func: represent a pin function.
+ * @name: name of the pin function, used to lookup the function.
+ * @groups: one or more names of pin groups that provide this function.
+ * @num_groups: number of groups included in @groups.
+ */
+struct samsung_pmx_func {
+	const char		*name;
+	const char		**groups;
+	u8			num_groups;
+};
+
+/* list of all exported SoC specific data */
+extern struct samsung_pin_ctrl exynos4210_pin_ctrl[];
+
+#endif /* __PINCTRL_SAMSUNG_H */