Commit 56d47fbb authored by 周琰杰 (Zhou Yanjie)'s avatar 周琰杰 (Zhou Yanjie) Committed by Thomas Bogendoerfer

MIPS: Ingenic: Add YSH & ATIL CU Neo board support.

Add a device tree and a defconfig for the Ingenic X1830 based
YSH & ATIL CU Neo board.
Tested-by: default avatar周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: default avatar周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: default avatarThomas Bogendoerfer <tsbogend@alpha.franken.de>
parent 1c3dea35
...@@ -4,5 +4,6 @@ dtb-$(CONFIG_JZ4740_RS90) += rs90.dtb ...@@ -4,5 +4,6 @@ dtb-$(CONFIG_JZ4740_RS90) += rs90.dtb
dtb-$(CONFIG_JZ4770_GCW0) += gcw0.dtb dtb-$(CONFIG_JZ4770_GCW0) += gcw0.dtb
dtb-$(CONFIG_JZ4780_CI20) += ci20.dtb dtb-$(CONFIG_JZ4780_CI20) += ci20.dtb
dtb-$(CONFIG_X1000_CU1000_NEO) += cu1000-neo.dtb dtb-$(CONFIG_X1000_CU1000_NEO) += cu1000-neo.dtb
dtb-$(CONFIG_X1830_CU1830_NEO) += cu1830-neo.dtb
obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y)) obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "x1830.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/ingenic,tcu.h>
#include <dt-bindings/interrupt-controller/irq.h>
/ {
compatible = "yna,cu1830-neo", "ingenic,x1830";
model = "YSH & ATIL General Board CU1830-Neo";
aliases {
serial1 = &uart1;
};
chosen {
stdout-path = "serial1:115200n8";
};
memory {
device_type = "memory";
reg = <0x0 0x08000000>;
};
leds {
compatible = "gpio-leds";
led-0 {
gpios = <&gpc 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
};
};
wlan_pwrseq: msc1-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpc 13 GPIO_ACTIVE_LOW>;
post-power-on-delay-ms = <200>;
};
};
&exclk {
clock-frequency = <24000000>;
};
&tcu {
/* 1500 kHz for the system timer and clocksource */
assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
assigned-clock-rates = <1500000>, <1500000>;
/* Use channel #0 for the system timer channel #2 for the clocksource */
ingenic,pwm-channels-mask = <0xfa>;
};
&uart1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pins_uart1>;
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
pinctrl-names = "default";
pinctrl-0 = <&pins_i2c0>;
ads7830: adc@48 {
compatible = "ti,ads7830";
reg = <0x48>;
};
};
&msc0 {
status = "okay";
bus-width = <4>;
max-frequency = <50000000>;
pinctrl-names = "default";
pinctrl-0 = <&pins_msc0>;
non-removable;
};
&msc1 {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
max-frequency = <50000000>;
pinctrl-names = "default";
pinctrl-0 = <&pins_msc1>;
non-removable;
mmc-pwrseq = <&wlan_pwrseq>;
ap6212a: wifi@1 {
compatible = "brcm,bcm4329-fmac";
reg = <1>;
interrupt-parent = <&gpc>;
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
interrupt-names = "host-wake";
brcm,drive-strength = <10>;
};
};
&mac {
status = "okay";
phy-mode = "rmii";
phy-handle = <&ip101gr>;
pinctrl-names = "default";
pinctrl-0 = <&pins_mac>;
snps,reset-gpio = <&gpb 28 GPIO_ACTIVE_LOW>; /* PB28 */
snps,reset-active-low;
snps,reset-delays-us = <0 10000 30000>;
};
&mdio {
status = "okay";
ip101gr: ethernet-phy@0 {
compatible = "ethernet-phy-id0243.0c54", "ethernet-phy-ieee802.3-c22";
reg = <0>;
};
};
&pinctrl {
pins_uart1: uart1 {
function = "uart1";
groups = "uart1-data";
bias-pull-up;
};
pins_i2c0: i2c0 {
function = "i2c0";
groups = "i2c0-data";
bias-pull-up;
};
pins_msc0: msc0 {
function = "mmc0";
groups = "mmc0-1bit", "mmc0-4bit";
bias-disable;
};
pins_msc1: msc1 {
function = "mmc1";
groups = "mmc1-1bit", "mmc1-4bit";
bias-disable;
};
pins_mac: mac {
function = "mac";
groups = "mac";
bias-disable;
};
};
CONFIG_LOCALVERSION_AUTO=y
CONFIG_KERNEL_GZIP=y
CONFIG_SYSVIPC=y
CONFIG_NO_HZ_IDLE=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_PREEMPT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_CGROUPS=y
CONFIG_MEMCG=y
CONFIG_MEMCG_KMEM=y
CONFIG_CGROUP_SCHED=y
CONFIG_CGROUP_FREEZER=y
CONFIG_CGROUP_DEVICE=y
CONFIG_CGROUP_CPUACCT=y
CONFIG_NAMESPACES=y
CONFIG_USER_NS=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_KALLSYMS_ALL=y
CONFIG_EMBEDDED=y
# CONFIG_VM_EVENT_COUNTERS is not set
# CONFIG_COMPAT_BRK is not set
CONFIG_SLAB=y
CONFIG_MACH_INGENIC=y
CONFIG_X1830_CU1830_NEO=y
CONFIG_HIGHMEM=y
CONFIG_HZ_100=y
# CONFIG_SECCOMP is not set
# CONFIG_SUSPEND is not set
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
# CONFIG_COMPACTION is not set
CONFIG_CMA=y
CONFIG_CMA_AREAS=7
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_CFG80211=y
CONFIG_UEVENT_HELPER=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_DEVTMPFS=y
# CONFIG_FW_LOADER is not set
# CONFIG_ALLOW_DEV_COREDUMP is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
CONFIG_BLK_DEV_DM=y
CONFIG_NETDEVICES=y
CONFIG_STMMAC_ETH=y
CONFIG_ICPLUS_PHY=y
CONFIG_BRCMFMAC=y
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_LEGACY_PTY_COUNT=2
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=2
CONFIG_SERIAL_8250_RUNTIME_UARTS=2
CONFIG_SERIAL_8250_INGENIC=y
CONFIG_SERIAL_OF_PLATFORM=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_JZ4780=y
CONFIG_GPIO_SYSFS=y
CONFIG_SENSORS_ADS7828=y
CONFIG_WATCHDOG=y
CONFIG_JZ4740_WDT=y
# CONFIG_LCD_CLASS_DEVICE is not set
# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
# CONFIG_VGA_CONSOLE is not set
# CONFIG_HID is not set
# CONFIG_USB_SUPPORT is not set
CONFIG_MMC=y
CONFIG_MMC_JZ4740=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_TRIGGERS=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_JZ4740=y
CONFIG_DMADEVICES=y
CONFIG_DMA_JZ4780=y
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_NVMEM=y
CONFIG_NVMEM_SYSFS=y
CONFIG_EXT4_FS=y
# CONFIG_DNOTIFY is not set
CONFIG_AUTOFS_FS=y
CONFIG_PROC_KCORE=y
# CONFIG_PROC_PAGE_MONITOR is not set
CONFIG_TMPFS=y
CONFIG_CONFIGFS_FS=y
CONFIG_NFS_FS=y
CONFIG_NLS=y
CONFIG_NLS_CODEPAGE_936=y
CONFIG_NLS_CODEPAGE_950=y
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
CONFIG_NLS_UTF8=y
CONFIG_CRYPTO_ECHAINIV=y
CONFIG_CRYPTO_AES=y
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_LZO=y
CONFIG_PRINTK_TIME=y
CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
CONFIG_CONSOLE_LOGLEVEL_QUIET=15
CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
CONFIG_DEBUG_INFO=y
CONFIG_STRIP_ASM_SYMS=y
CONFIG_DEBUG_FS=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_PANIC_ON_OOPS=y
CONFIG_PANIC_TIMEOUT=10
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_PREEMPT is not set
CONFIG_STACKTRACE=y
# CONFIG_FTRACE is not set
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="earlycon clk_ignore_unused"
...@@ -31,6 +31,10 @@ config X1000_CU1000_NEO ...@@ -31,6 +31,10 @@ config X1000_CU1000_NEO
bool "YSH & ATIL CU1000 Module with Neo backplane" bool "YSH & ATIL CU1000 Module with Neo backplane"
select MACH_X1000 select MACH_X1000
config X1830_CU1830_NEO
bool "YSH & ATIL CU1830 Module with Neo backplane"
select MACH_X1830
endchoice endchoice
config MACH_JZ4725B config MACH_JZ4725B
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment