Merge tag 'qcom-arm64-for-5.7' of...

Merge tag 'qcom-arm64-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/late

Qualcomm ARM64 DT updates for v5.7

This brings initial support for the SM8250 and IPQ6018 platforms.

SDM845 gets audio, PCIe and IP-accelerator support, and the interconnect
providers are refactored. The Lenovo Yoga C630 has audio enabled and the
DB845c has PCIe, analog audio and low-speed interfaces enabled. The
SDM845 MTP has its display enabled and firmware location updated to
match linux-firmware.

SC7180 gains CPU topology and power properties. Interconnect providers,
eMMC, SD-card, multimedia clocks, display, Bluetooth, Venus are added.
Critical trip points are added as well as various fixes.

For MSM8916 FastRPC support is added, ETM power management and reserved
memory for Samsung A2015 are corrected.

MSM8996 switches to generic QMP phy driver for its UFS support. MSM8998
temporarily disables part of Coresight to boot without
clk_ignore_unused.  CEQ for eMMC on QCS404 is enabled.

Fixes throughout the platforms to fix binding compliance, correct
compatibles for SDHCI nodes and add gpio-ranges.

* tag 'qcom-arm64-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (56 commits)
  arm64: dts: qcom: sdm845-mtp: Relocate remoteproc firmware
  arm64: dts: sdm845: add IPA information
  arm64: dts: qcom: db845c: add analog audio support
  arm64: dts: qcom: sdm845: add pinctrl nodes for quat i2s
  arm64: dts: qcom: c630: Enable audio support
  arm64: dts: qcom: sdm845: add apr nodes
  arm64: dts: qcom: sdm845: add slimbus nodes
  arm64: dts: qcom: sc7180: Update reg names for SDHC
  arm64: dts: qcom: qcs404: Enable CQE support for eMMC
  arm64: dts: msm8916: Add fastrpc node
  arm64: dts: qcom: sm8250: Add sm8250 dts file
  arm64: dts: qcom: msm8998-mtp: Disable funnel 4 and 5
  arm64: dts: qcom: db845c: add Low speed expansion i2c and spi nodes
  arm64: dts: qcom: apq8016-sbc: Remove wrong regulator supply
  arm64: dts: qcom: sc7180: Added critical trip point Thermal-zones node
  arm64: dts: qcom: msm8998: Fix cpu compatible
  arm64: dts: qcom: sc7180: Add OSM L3 interconnect provider
  arm64: dts: qcom: sdm845: Add OSM L3 interconnect provider
  arm64: dts: sc7180: Add interconnect provider DT nodes
  arm64: dts: qcom: msm8996: Use generic QMP driver for UFS
  ...

Link: https://lore.kernel.org/r/20200318043823.GA470201@yogaSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/qcom.yaml

@@ -28,6 +28,7 @@ description: |
         apq8074
         apq8084
         apq8096
+        ipq6018
         ipq8074
         mdm9615
         msm8916
@@ -41,6 +42,7 @@ description: |
   The 'board' element must be one of the following strings:
 
         cdp
+        cp01-c1
         dragonboard
         hk01
         idp
@@ -150,4 +152,10 @@ properties:
           - enum:
               - qcom,sc7180-idp
           - const: qcom,sc7180
+
+      - items:
+          - enum:
+              - qcom,ipq6018-cp01-c1
+          - const: qcom,ipq6018
+
 ...

arch/arm64/boot/dts/qcom/Makefile

@@ -2,6 +2,7 @@
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-longcheer-l8150.dtb
@@ -22,5 +23,6 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb

arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi

@@ -562,7 +562,6 @@ &wcd_codec {
 
 &smd_rpm_regulators {
 	vdd_l1_l2_l3-supply = <&pm8916_s3>;
-	vdd_l5-supply = <&pm8916_s3>;
 	vdd_l4_l5_l6-supply = <&pm8916_s4>;
 	vdd_l7-supply = <&pm8916_s4>;
 

arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi

@@ -999,13 +999,7 @@ &ufsphy {
 
 	vdda-phy-supply = <&vreg_l28a_0p925>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
-
-	vdda-phy-max-microamp = <18380>;
-	vdda-pll-max-microamp = <9440>;
-
 	vddp-ref-clk-supply = <&vreg_l25a_1p2>;
-	vddp-ref-clk-max-microamp = <100>;
-	vddp-ref-clk-always-on;
 };
 
 &ufshc {

arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * IPQ6018 CP01 board device tree source
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1";
+	compatible = "qcom,ipq6018-cp01", "qcom,ipq6018";
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-append = " swiotlb=1";
+	};
+};
+
+&blsp1_uart3 {
+	pinctrl-0 = <&serial_3_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&i2c_1 {
+	pinctrl-0 = <&i2c_1_pins>;
+	pinctrl-names = "default";
+	status = "ok";
+};
+
+&spi_0 {
+	cs-select = <0>;
+	status = "ok";
+
+	m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		compatible = "n25q128a11";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&tlmm {
+	i2c_1_pins: i2c-1-pins {
+		pins = "gpio42", "gpio43";
+		function = "blsp2_i2c";
+		drive-strength = <8>;
+	};
+
+	spi_0_pins: spi-0-pins {
+		pins = "gpio38", "gpio39", "gpio40", "gpio41";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+};

arch/arm64/boot/dts/qcom/ipq8074.dtsi

@@ -21,6 +21,7 @@ tlmm: pinctrl@1000000 {
 			reg = <0x1000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 70>;
 			#gpio-cells = <0x2>;
 			interrupt-controller;
 			#interrupt-cells = <0x2>;

arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi

@@ -15,6 +15,14 @@ chosen {
 		stdout-path = "serial0";
 	};
 
+	reserved-memory {
+		/* Additional memory used by Samsung firmware modifications */
+		tz-apps@85500000 {
+			reg = <0x0 0x85500000 0x0 0xb00000>;
+			no-map;
+		};
+	};
+
 	soc {
 		sdhci@7824000 {
 			status = "okay";

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -423,6 +423,7 @@ msmgpio: pinctrl@1000000 {
 			reg = <0x1000000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 122>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -860,7 +861,7 @@ tsens_calsel: calsel@ec {
 		};
 
 		tsens: thermal-sensor@4a9000 {
-			compatible = "qcom,msm8916-tsens";
+			compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
@@ -1129,6 +1130,20 @@ smd-edge {
 				qcom,remote-pid = <1>;
 
 				label = "hexagon";
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,smd-channels = "fastrpcsmd-apps-dsp";
+					label = "adsp";
+
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					cb@1{
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+					};
+				};
 			};
 		};
 
@@ -1415,6 +1430,7 @@ etm@85c000 {
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU0>;
 
@@ -1433,6 +1449,7 @@ etm@85d000 {
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU1>;
 
@@ -1451,6 +1468,7 @@ etm@85e000 {
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU2>;
 
@@ -1469,6 +1487,7 @@ etm@85f000 {
 
 			clocks = <&rpmcc RPM_QDSS_CLK>, <&rpmcc RPM_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
+			arm,coresight-loses-context-with-cpu;
 
 			cpu = <&CPU3>;
 

arch/arm64/boot/dts/qcom/msm8992.dtsi

@@ -171,6 +171,7 @@ msmgpio: pinctrl@fd510000 {
 			reg = <0xfd510000 0x4000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;

arch/arm64/boot/dts/qcom/msm8994.dtsi

@@ -133,6 +133,7 @@ msmgpio: pinctrl@fd510000 {
 			reg = <0xfd510000 0x4000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 146>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;

arch/arm64/boot/dts/qcom/msm8996.dtsi

@@ -443,10 +443,13 @@ gcc: clock-controller@300000 {
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0x00300000 0x90000>;
+
+			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>;
+			clock-names = "cxo2";
 		};
 
 		tsens0: thermal-sensor@4a9000 {
-			compatible = "qcom,msm8996-tsens";
+			compatible = "qcom,msm8996-tsens", "qcom,tsens-v2";
 			reg = <0x004a9000 0x1000>, /* TM */
 			      <0x004a8000 0x1000>; /* SROT */
 			#qcom,sensors = <13>;
@@ -457,7 +460,7 @@ tsens0: thermal-sensor@4a9000 {
 		};
 
 		tsens1: thermal-sensor@4ad000 {
-			compatible = "qcom,msm8996-tsens";
+			compatible = "qcom,msm8996-tsens", "qcom,tsens-v2";
 			reg = <0x004ad000 0x1000>, /* TM */
 			      <0x004ac000 0x1000>; /* SROT */
 			#qcom,sensors = <8>;
@@ -695,6 +698,7 @@ msmgpio: pinctrl@1010000 {
 			reg = <0x01010000 0x300000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 150>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -882,7 +886,7 @@ ufshc: ufshc@624000 {
 			reg = <0x00624000 0x2500>;
 			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
 
-			phys = <&ufsphy>;
+			phys = <&ufsphy_lane>;
 			phy-names = "ufsphy";
 
 			power-domains = <&gcc UFS_GDSC>;
@@ -934,16 +938,25 @@ ufs_variant {
 		};
 
 		ufsphy: phy@627000 {
-			compatible = "qcom,msm8996-ufs-phy-qmp-14nm";
-			reg = <0x00627000 0xda8>;
-			reg-names = "phy_mem";
-			#phy-cells = <0>;
+			compatible = "qcom,msm8996-qmp-ufs-phy";
+			reg = <0x00627000 0x1c4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_UFS_CLKREF_CLK>;
+			clock-names = "ref";
 
-			clock-names = "ref_clk_src", "ref_clk";
-			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
-				 <&gcc GCC_UFS_CLKREF_CLK>;
 			resets = <&ufshc 0>;
+			reset-names = "ufsphy";
 			status = "disabled";
+
+			ufsphy_lane: lanes@627400 {
+				reg = <0x627400 0x12c>,
+				      <0x627600 0x200>,
+				      <0x627c00 0x1b4>;
+				#phy-cells = <0>;
+			};
 		};
 
 		camss: camss@a00000 {

arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi

@@ -95,11 +95,15 @@ &funnel3 {
 };
 
 &funnel4 {
-	status = "okay";
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
 };
 
 &funnel5 {
-	status = "okay";
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
 };
 
 &pm8005_lsid1 {

arch/arm64/boot/dts/qcom/msm8998.dtsi

@@ -130,7 +130,7 @@ cpus {
 
 		CPU0: cpu@0 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -149,7 +149,7 @@ L1_D_0: l1-dcache {
 
 		CPU1: cpu@1 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -164,7 +164,7 @@ L1_D_1: l1-dcache {
 
 		CPU2: cpu@2 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x2>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -179,7 +179,7 @@ L1_D_2: l1-dcache {
 
 		CPU3: cpu@3 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x3>;
 			enable-method = "psci";
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
@@ -194,7 +194,7 @@ L1_D_3: l1-dcache {
 
 		CPU4: cpu@100 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
@@ -213,7 +213,7 @@ L1_D_100: l1-dcache {
 
 		CPU5: cpu@101 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x101>;
 			enable-method = "psci";
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
@@ -228,7 +228,7 @@ L1_D_101: l1-dcache {
 
 		CPU6: cpu@102 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x102>;
 			enable-method = "psci";
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
@@ -243,7 +243,7 @@ L1_D_102: l1-dcache {
 
 		CPU7: cpu@103 {
 			device_type = "cpu";
-			compatible = "arm,armv8";
+			compatible = "qcom,kryo280";
 			reg = <0x0 0x103>;
 			enable-method = "psci";
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;

arch/arm64/boot/dts/qcom/pm6150.dtsi

@@ -20,7 +20,7 @@ pm6150_pon: pon@800 {
 			mode-bootloader = <0x2>;
 			mode-recovery = <0x1>;
 
-			pwrkey {
+			pm6150_pwrkey: pwrkey {
 				compatible = "qcom,pm8941-pwrkey";
 				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 				debounce = <15625>;

arch/arm64/boot/dts/qcom/pm8998.dtsi

@@ -45,7 +45,7 @@ pm8998_pon: pon@800 {
 			mode-bootloader = <0x2>;
 			mode-recovery = <0x1>;
 
-			pwrkey {
+			pm8998_pwrkey: pwrkey {
 				compatible = "qcom,pm8941-pwrkey";
 				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 				debounce = <15625>;

arch/arm64/boot/dts/qcom/qcs404-evb.dtsi

@@ -200,6 +200,7 @@ vreg_l13_3p3: l13 {
 &sdcc1 {
 	status = "ok";
 
+	supports-cqe;
 	mmc-ddr-1_8v;
 	mmc-hs400-1_8v;
 	bus-width = <8>;

arch/arm64/boot/dts/qcom/qcs404.dtsi

@@ -685,9 +685,9 @@ pcie_phy: phy@7786000 {
 		};
 
 		sdcc1: sdcc@7804000 {
-			compatible = "qcom,sdhci-msm-v5";
+			compatible = "qcom,qcs404-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
-			reg-names = "hc_mem", "cmdq_mem";
+			reg-names = "hc", "cqhci";
 
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;

arch/arm64/boot/dts/qcom/sc7180-idp.dts

@@ -7,6 +7,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sc7180.dtsi"
 #include "pm6150.dtsi"
@@ -17,6 +18,7 @@ / {
 	compatible = "qcom,sc7180-idp", "qcom,sc7180";
 
 	aliases {
+		bluetooth0 = &bluetooth;
 		hsuart0 = &uart3;
 		serial0 = &uart8;
 	};
@@ -101,9 +103,9 @@ vreg_l11a_1p8: ldo11 {
 		};
 
 		vreg_l12a_1p8: ldo12 {
-			regulator-min-microvolt = <1696000>;
-			regulator-max-microvolt = <1952000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l13a_1p8: ldo13 {
@@ -143,9 +145,9 @@ vreg_l18a_2p8: ldo18 {
 		};
 
 		vreg_l19a_2p9: ldo19 {
-			regulator-min-microvolt = <2696000>;
-			regulator-max-microvolt = <3304000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 	};
 
@@ -189,9 +191,9 @@ vreg_l5c_1p8: ldo5 {
 		};
 
 		vreg_l6c_2p9: ldo6 {
-			regulator-min-microvolt = <2696000>;
-			regulator-max-microvolt = <3304000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l7c_3p0: ldo7 {
@@ -207,9 +209,9 @@ vreg_l8c_1p8: ldo8 {
 		};
 
 		vreg_l9c_2p9: ldo9 {
-			regulator-min-microvolt = <2952000>;
-			regulator-max-microvolt = <3304000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vreg_l10c_3p3: ldo10 {
@@ -254,8 +256,40 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+	vmmc-supply = <&vreg_l19a_2p9>;
+	vqmmc-supply = <&vreg_l12a_1p8>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+	vmmc-supply  = <&vreg_l9c_2p9>;
+	vqmmc-supply = <&vreg_l6c_2p9>;
+
+	cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
+};
+
 &uart3 {
 	status = "okay";
+
+	bluetooth: wcn3990-bt {
+		compatible = "qcom,wcn3990-bt";
+		vddio-supply = <&vreg_l10a_1p8>;
+		vddxo-supply = <&vreg_l1c_1p8>;
+		vddrf-supply = <&vreg_l2c_1p3>;
+		vddch0-supply = <&vreg_l10c_3p3>;
+		max-speed = <3200000>;
+		clocks = <&rpmhcc RPMH_RF_CLK2>;
+	};
 };
 
 &uart8 {
@@ -287,6 +321,12 @@ &usb_1_qmpphy {
 	vdda-pll-supply = <&vreg_l4a_0p8>;
 };
 
+&venus {
+	video-firmware {
+		iommus = <&apps_smmu 0x0c42 0x0>;
+	};
+};
+
 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
 
 &qspi_clk {

arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi

@@ -614,6 +614,11 @@ touchscreen@10 {
 	};
 };
 
+&ipa {
+	status = "okay";
+	modem-init;
+};
+
 &lpasscc {
 	status = "okay";
 };
@@ -626,6 +631,10 @@ &mdss_mdp {
 	status = "okay";
 };
 
+&pm8998_pwrkey {
+	status = "disabled";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -1292,3 +1301,9 @@ config {
 		};
 	};
 };
+
+&venus {
+	video-firmware {
+		iommus = <&apps_smmu 0x10b2 0x0>;
+	};
+};

arch/arm64/boot/dts/qcom/sdm845-db845c.dts

@@ -8,6 +8,8 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
 #include "sdm845.dtsi"
 #include "pm8998.dtsi"
 #include "pmi8998.dtsi"
@@ -359,11 +361,56 @@ zap-shader {
 	};
 };
 
+&i2c11 {
+	/* On Low speed expansion */
+	label = "LS-I2C1";
+	status = "okay";
+};
+
+&i2c14 {
+	/* On Low speed expansion */
+	label = "LS-I2C0";
+	status = "okay";
+};
+
 &mss_pil {
 	status = "okay";
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
 };
 
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
+
+	vddpe-3v3-supply = <&pcie0_3p3v_dual>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie0_default_state>;
+};
+
+&pcie0_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
+&pcie1 {
+	status = "okay";
+	perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_default_state>;
+};
+
+&pcie1_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+};
+
 &pm8998_gpio {
 	vol_up_pin_a: vol-up-active {
 		pins = "gpio6";
@@ -384,6 +431,37 @@ resin {
 	};
 };
 
+/* QUAT I2S Uses 4 I2S SD Lines for audio on LT9611 HDMI Bridge */
+&q6afedai {
+	qi2s@22 {
+		reg = <22>;
+		qcom,sd-lines = <0 1 2 3>;
+	};
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+		direction = <2>;
+	};
+
+	dai@1 {
+		reg = <1>;
+		direction = <2>;
+	};
+
+	dai@2 {
+		reg = <2>;
+		direction = <1>;
+	};
+
+	dai@3 {
+		reg = <3>;
+		direction = <2>;
+		is-compress-dai;
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -405,7 +483,121 @@ &sdhc_2 {
 	cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
 };
 
+&sound {
+	compatible = "qcom,db845c-sndcard";
+	pinctrl-0 = <&quat_mi2s_active
+			 &quat_mi2s_sd0_active
+			 &quat_mi2s_sd1_active
+			 &quat_mi2s_sd2_active
+			 &quat_mi2s_sd3_active>;
+	pinctrl-names = "default";
+	model = "DB845c";
+	audio-routing =
+		"RX_BIAS", "MCLK",
+		"AMIC1", "MIC BIAS1",
+		"AMIC2", "MIC BIAS2",
+		"DMIC0", "MIC BIAS1",
+		"DMIC1", "MIC BIAS1",
+		"DMIC2", "MIC BIAS3",
+		"DMIC3", "MIC BIAS3",
+		"SpkrLeft IN", "SPK1 OUT",
+		"SpkrRight IN", "SPK2 OUT",
+		"MM_DL1",  "MultiMedia1 Playback",
+		"MM_DL2",  "MultiMedia2 Playback",
+		"MM_DL4",  "MultiMedia4 Playback",
+		"MultiMedia3 Capture", "MM_UL3";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	mm4-dai-link {
+		link-name = "MultiMedia4";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA4>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai =  <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9340 1>;
+		};
+	};
+};
+
+&spi2 {
+	/* On Low speed expansion */
+	label = "LS-SPI0";
+	status = "okay";
+};
+
 &tlmm {
+	pcie0_default_state: pcie0-default {
+		clkreq {
+			pins = "gpio36";
+			function = "pci_e0";
+			bias-pull-up;
+		};
+
+		reset-n {
+			pins = "gpio35";
+			function = "gpio";
+
+			drive-strength = <2>;
+			output-low;
+			bias-pull-down;
+		};
+
+		wake-n {
+			pins = "gpio37";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	pcie0_pwren_state: pcie0-pwren {
 		pins = "gpio90";
 		function = "gpio";
@@ -414,6 +606,39 @@ pcie0_pwren_state: pcie0-pwren {
 		bias-disable;
 	};
 
+	pcie1_default_state: pcie1-default {
+		perst-n {
+			pins = "gpio102";
+			function = "gpio";
+
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		clkreq {
+			pins = "gpio103";
+			function = "pci_e1";
+			bias-pull-up;
+		};
+
+		wake-n {
+			pins = "gpio11";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		reset-n {
+			pins = "gpio75";
+			function = "gpio";
+
+			drive-strength = <16>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+
 	sdc2_default_state: sdc2-default {
 		clk {
 			pins = "sdc2_clk";
@@ -444,6 +669,20 @@ sdc2_card_det_n: sd-card-det-n {
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	wcd_intr_default: wcd_intr_default {
+		pins = <54>;
+		function = "gpio";
+
+		input-enable;
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+};
+
+&uart3 {
+	label = "LS-UART0";
+	status = "disabled";
 };
 
 &uart6 {
@@ -461,6 +700,7 @@ bluetooth {
 };
 
 &uart9 {
+	label = "LS-UART1";
 	status = "okay";
 };
 
@@ -534,6 +774,39 @@ &ufs_mem_phy {
 	vdda-pll-supply = <&vreg_l26a_1p2>;
 };
 
+&wcd9340{
+	pinctrl-0 = <&wcd_intr_default>;
+	pinctrl-names = "default";
+	clock-names = "extclk";
+	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+	reset-gpios = <&tlmm 64 0>;
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
+
+	swm: swm@c85 {
+		left_spkr: wsa8810-left{
+			compatible = "sdw10217201000";
+			reg = <0 1>;
+			powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
+			#thermal-sensor-cells = <0>;
+			sound-name-prefix = "SpkrLeft";
+			#sound-dai-cells = <0>;
+		};
+
+		right_spkr: wsa8810-right{
+			compatible = "sdw10217201000";
+			powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
+			reg = <0 2>;
+			#thermal-sensor-cells = <0>;
+			sound-name-prefix = "SpkrRight";
+			#sound-dai-cells = <0>;
+		};
+	};
+};
+
 &wifi {
 	status = "okay";
 
@@ -546,6 +819,16 @@ &wifi {
 };
 
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
+&qup_spi2_default {
+	drive-strength = <16>;
+};
+
+&qup_uart3_default{
+	pinmux {
+		pins = "gpio41", "gpio42", "gpio43", "gpio44";
+		function = "qup3";
+	};
+};
 
 &qup_uart6_default {
 	pinmux {

arch/arm64/boot/dts/qcom/sdm845-mtp.dts

@@ -50,6 +50,7 @@ vreg_s4a_1p8: pm8998-smps4 {
 
 &adsp_pas {
 	status = "okay";
+	firmware-name = "qcom/sdm845/adsp.mdt";
 };
 
 &apps_rsc {
@@ -350,6 +351,81 @@ vreg_s3c_0p6: smps3 {
 
 &cdsp_pas {
 	status = "okay";
+	firmware-name = "qcom/sdm845/cdsp.mdt";
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&truly_in_0>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+
+	panel@0 {
+		compatible = "truly,nt35597-2K-display";
+		reg = <0>;
+		vdda-supply = <&vreg_l14a_1p88>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+		mode-gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				truly_in_0: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				truly_in_1: endpoint {
+					remote-endpoint = <&dsi1_out>;
+				};
+			};
+		};
+	};
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+&dsi1 {
+	status = "okay";
+	vdda-supply = <&vdda_mipi_dsi1_1p2>;
+
+	qcom,dual-dsi-mode;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&truly_in_1>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&dsi1_phy {
+	status = "okay";
+	vdds-supply = <&vdda_mipi_dsi1_pll>;
 };
 
 &gcc {
@@ -372,6 +448,19 @@ &i2c10 {
 	clock-frequency = <400000>;
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
+&mss_pil {
+	status = "okay";
+	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };

arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts

@@ -7,7 +7,10 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
 #include "sdm845.dtsi"
 #include "pm8998.dtsi"
 
@@ -353,6 +356,75 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+		direction = <2>;
+	};
+
+	dai@1 {
+		reg = <1>;
+		direction = <1>;
+	};
+};
+
+&sound {
+	compatible = "qcom,db845c-sndcard";
+	model = "Lenovo-YOGA-C630-13Q50";
+
+	audio-routing =
+		"RX_BIAS", "MCLK",
+		"AMIC2", "MIC BIAS2",
+		"SpkrLeft IN", "SPK1 OUT",
+		"SpkrRight IN", "SPK2 OUT",
+		"MM_DL1",  "MultiMedia1 Playback",
+		"MultiMedia2 Capture", "MM_UL2";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai =  <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9340 1>;
+		};
+	};
+};
+
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <81 4>;
 
@@ -382,6 +454,15 @@ i2c12_hid_active: i2c12-hid-active {
 		bias-pull-up;
 		drive-strength = <2>;
 	};
+
+	wcd_intr_default: wcd_intr_default {
+		pins = <54>;
+		function = "gpio";
+
+		input-enable;
+		bias-pull-down;
+		drive-strength = <2>;
+	};
 };
 
 &uart6 {
@@ -465,3 +546,36 @@ &usb_2_qmpphy {
 	vdda-phy-supply = <&vdda_usb2_ss_1p2>;
 	vdda-pll-supply = <&vdda_usb2_ss_core>;
 };
+
+&wcd9340{
+	pinctrl-0 = <&wcd_intr_default>;
+	pinctrl-names = "default";
+	clock-names = "extclk";
+	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+	reset-gpios = <&tlmm 64 0>;
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
+
+	swm: swm@c85 {
+		left_spkr: wsa8810-left{
+			compatible = "sdw10217211000";
+			reg = <0 3>;
+			powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
+			#thermal-sensor-cells = <0>;
+			sound-name-prefix = "SpkrLeft";
+			#sound-dai-cells = <0>;
+		};
+
+		right_spkr: wsa8810-right{
+			compatible = "sdw10217211000";
+			powerdown-gpios = <&wcdgpio 3 GPIO_ACTIVE_HIGH>;
+			reg = <0 4>;
+			#thermal-sensor-cells = <0>;
+			sound-name-prefix = "SpkrRight";
+			#sound-dai-cells = <0>;
+		};
+	};
+};

arch/arm64/boot/dts/qcom/sm8250-mtp.dts

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "sm8250.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SM8250 MTP";
+	compatible = "qcom,sm8250-mtp";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};

arch/arm64/boot/dts/qcom/sm8250.dtsi

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <38400000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+				      compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&L2_100>;
+			L2_100: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			next-level-cache = <&L2_200>;
+			L2_200: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			next-level-cache = <&L2_300>;
+			L2_300: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			next-level-cache = <&L2_400>;
+			L2_400: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			next-level-cache = <&L2_500>;
+			L2_500: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			next-level-cache = <&L2_600>;
+			L2_600: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo485";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			next-level-cache = <&L2_700>;
+			L2_700: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm";
+			#reset-cells = <1>;
+		};
+	};
+
+	tcsr_mutex: hwlock {
+		compatible = "qcom,tcsr-mutex";
+		syscon = <&tcsr_mutex_regs 0 0x1000>;
+		#hwlock-cells = <1>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0x80000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@80000000 {
+			reg = <0x0 0x80000000 0x0 0x600000>;
+			no-map;
+		};
+
+		xbl_aop_mem: memory@80700000 {
+			reg = <0x0 0x80700000 0x0 0x160000>;
+			no-map;
+		};
+
+		cmd_db: memory@80860000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x0 0x80860000 0x0 0x20000>;
+			no-map;
+		};
+
+		smem_mem: memory@80900000 {
+			reg = <0x0 0x80900000 0x0 0x200000>;
+			no-map;
+		};
+
+		removed_mem: memory@80b00000 {
+			reg = <0x0 0x80b00000 0x0 0x5300000>;
+			no-map;
+		};
+
+		camera_mem: memory@86200000 {
+			reg = <0x0 0x86200000 0x0 0x500000>;
+			no-map;
+		};
+
+		wlan_mem: memory@86700000 {
+			reg = <0x0 0x86700000 0x0 0x100000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@86800000 {
+			reg = <0x0 0x86800000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: memory@86810000 {
+			reg = <0x0 0x86810000 0x0 0xa000>;
+			no-map;
+		};
+
+		gpu_mem: memory@8681a000 {
+			reg = <0x0 0x8681a000 0x0 0x2000>;
+			no-map;
+		};
+
+		npu_mem: memory@86900000 {
+			reg = <0x0 0x86900000 0x0 0x500000>;
+			no-map;
+		};
+
+		video_mem: memory@86e00000 {
+			reg = <0x0 0x86e00000 0x0 0x500000>;
+			no-map;
+		};
+
+		cvp_mem: memory@87300000 {
+			reg = <0x0 0x87300000 0x0 0x500000>;
+			no-map;
+		};
+
+		cdsp_mem: memory@87800000 {
+			reg = <0x0 0x87800000 0x0 0x1400000>;
+			no-map;
+		};
+
+		slpi_mem: memory@88c00000 {
+			reg = <0x0 0x88c00000 0x0 0x1500000>;
+			no-map;
+		};
+
+		adsp_mem: memory@8a100000 {
+			reg = <0x0 0x8a100000 0x0 0x1d00000>;
+			no-map;
+		};
+
+		spss_mem: memory@8be00000 {
+			reg = <0x0 0x8be00000 0x0 0x100000>;
+			no-map;
+		};
+
+		cdsp_secure_heap: memory@8bf00000 {
+			reg = <0x0 0x8bf00000 0x0 0x4600000>;
+			no-map;
+		};
+	};
+
+	smem: qcom,smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_mem>;
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sm8250";
+			reg = <0x0 0x00100000 0x0 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clock-names = "bi_tcxo", "sleep_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
+		};
+
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc 133>, <&gcc 134>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			uart2: serial@a90000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc 113>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
+			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sm8250-pdc";
+			reg = <0x0b220000 0x30000>, <0x17c000f0 0x60>;
+			qcom,pdc-ranges = <0 480 94>, <94 609 31>,
+					  <125 63 1>, <126 716 12>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		spmi: qcom,spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0 0x0c440000 0x0 0x0001100>,
+			      <0x0 0x0c600000 0x0 0x2000000>,
+			      <0x0 0x0e600000 0x0 0x0100000>,
+			      <0x0 0x0e700000 0x0 0x00a0000>,
+			      <0x0 0x0c40a000 0x0 0x0026000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		apps_rsc: rsc@18200000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x0 0x18200000 0x0 0x10000>,
+				<0x0 0x18210000 0x0 0x10000>,
+				<0x0 0x18220000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
+					  <WAKE_TCS    3>, <CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sm8250-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+		};
+
+		tcsr_mutex_regs: syscon@1f40000 {
+			compatible = "syscon";
+			reg = <0x0 0x01f40000 0x0 0x40000>;
+		};
+
+		timer@17c20000 {
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0 0x17c20000 0x0 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17c21000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c21000 0x0 0x1000>,
+				      <0x0 0x17c22000 0x0 0x1000>;
+			};
+
+			frame@17c23000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c23000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c25000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c25000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c27000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c27000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c29000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c29000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				status = "disabled";
+			};
+		};
+
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 12
+				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};