Commit 57d90148 authored by Ivan Khoronzhuk's avatar Ivan Khoronzhuk Committed by David S. Miller

net: ethernet: ti: cpsw: add CBS Qdisc offload

The cpsw has up to 4 FIFOs per port and upper 3 FIFOs can feed rate
limited queue with shaping. In order to set and enable shaping for
those 3 FIFOs queues the network device with CBS qdisc attached is
needed. The CBS configuration is added for dual-emac/single port mode
only, but potentially can be used in switch mode also, based on
switchdev for instance.

Despite the FIFO shapers can work w/o cpdma level shapers the base
usage must be in combine with cpdma level shapers as described in TRM,
that are set as maximum rates for interface queues with sysfs.

One of the possible configuration with txq shapers and CBS shapers:

                      Configured with echo RATE >
                  /sys/class/net/eth0/queues/tx-0/tx_maxrate
             /---------------------------------------------------
            /
           /            cpdma level shapers
        +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+
        | c7 | | c6 | | c5 | | c4 | | c3 | | c2 | | c1 | | c0 |
        \    / \    / \    / \    / \    / \    / \    / \    /
         \  /   \  /   \  /   \  /   \  /   \  /   \  /   \  /
          \/     \/     \/     \/     \/     \/     \/     \/
+---------|------|------|------|-------------------------------------+
|    +----+      |      |  +---+                                     |
|    |      +----+      |  |                                         |
|    v      v           v  v                                         |
| +----+ +----+ +----+ +----+ p        p+----+ +----+ +----+ +----+  |
| |    | |    | |    | |    | o        o|    | |    | |    | |    |  |
| | f3 | | f2 | | f1 | | f0 | r  CPSW  r| f3 | | f2 | | f1 | | f0 |  |
| |    | |    | |    | |    | t        t|    | |    | |    | |    |  |
| \    / \    / \    / \    / 0        1\    / \    / \    / \    /  |
|  \  X   \  /   \  /   \  /             \  /   \  /   \  /   \  /   |
|   \/ \   \/     \/     \/               \/     \/     \/     \/    |
+-------\------------------------------------------------------------+
         \
          \ FIFO shaper, set with CBS offload added in this patch,
           \ FIFO0 cannot be rate limited
            ------------------------------------------------------

CBS shaper configuration is supposed to be used with root MQPRIO Qdisc
offload allowing to add sk_prio->tc->txq maps that direct traffic to
appropriate tx queue and maps L2 priority to FIFO shaper.

The CBS shaper is intended to be used for AVB where L2 priority
(pcp field) is used to differentiate class of traffic. So additionally
vlan needs to be created with appropriate egress sk_prio->l2 prio map.

If CBS has several tx queues assigned to it, the sum of their
bandwidth has not overlap bandwidth set for CBS. It's recomended the
CBS bandwidth to be a little bit more.

The CBS shaper is configured with CBS qdisc offload interface using tc
tool from iproute2 packet.

For instance:

$ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1

$ tc -g class show dev eth0
+---(100:ffe2) mqprio
|    +---(100:3) mqprio
|    +---(100:4) mqprio
|    
+---(100:ffe1) mqprio
|    +---(100:2) mqprio
|    
+---(100:ffe0) mqprio
     +---(100:1) mqprio

$ tc qdisc add dev eth0 parent 100:1 cbs locredit -1440 \
hicredit 60 sendslope -960000 idleslope 40000 offload 1

$ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \
hicredit 62 sendslope -980000 idleslope 20000 offload 1

The above code set CBS shapers for tc0 and tc1, for that txq0 and
txq1 is used. Pay attention, the real set bandwidth can differ a bit
due to discreteness of configuration parameters.

Here parameters like locredit, hicredit and sendslope are ignored
internally and are supposed to be set with assumption that maximum
frame size for frame - 1500.

It's supposed that interface speed is not changed while reconnection,
not always is true, so inform user in case speed of interface was
changed, as it can impact on dependent shapers configuration.

For more examples see Documentation.
Reviewed-by: default avatarIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: default avatarGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: default avatarIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 7929a668
...@@ -46,6 +46,8 @@ ...@@ -46,6 +46,8 @@
#include "cpts.h" #include "cpts.h"
#include "davinci_cpdma.h" #include "davinci_cpdma.h"
#include <net/pkt_sched.h>
#define CPSW_DEBUG (NETIF_MSG_HW | NETIF_MSG_WOL | \ #define CPSW_DEBUG (NETIF_MSG_HW | NETIF_MSG_WOL | \
NETIF_MSG_DRV | NETIF_MSG_LINK | \ NETIF_MSG_DRV | NETIF_MSG_LINK | \
NETIF_MSG_IFUP | NETIF_MSG_INTR | \ NETIF_MSG_IFUP | NETIF_MSG_INTR | \
...@@ -154,8 +156,12 @@ do { \ ...@@ -154,8 +156,12 @@ do { \
#define IRQ_NUM 2 #define IRQ_NUM 2
#define CPSW_MAX_QUEUES 8 #define CPSW_MAX_QUEUES 8
#define CPSW_CPDMA_DESCS_POOL_SIZE_DEFAULT 256 #define CPSW_CPDMA_DESCS_POOL_SIZE_DEFAULT 256
#define CPSW_FIFO_QUEUE_TYPE_SHIFT 16
#define CPSW_FIFO_SHAPE_EN_SHIFT 16
#define CPSW_FIFO_RATE_EN_SHIFT 20
#define CPSW_TC_NUM 4 #define CPSW_TC_NUM 4
#define CPSW_FIFO_SHAPERS_NUM (CPSW_TC_NUM - 1) #define CPSW_FIFO_SHAPERS_NUM (CPSW_TC_NUM - 1)
#define CPSW_PCT_MASK 0x7f
#define CPSW_RX_VLAN_ENCAP_HDR_PRIO_SHIFT 29 #define CPSW_RX_VLAN_ENCAP_HDR_PRIO_SHIFT 29
#define CPSW_RX_VLAN_ENCAP_HDR_PRIO_MSK GENMASK(2, 0) #define CPSW_RX_VLAN_ENCAP_HDR_PRIO_MSK GENMASK(2, 0)
...@@ -458,6 +464,8 @@ struct cpsw_priv { ...@@ -458,6 +464,8 @@ struct cpsw_priv {
bool rx_pause; bool rx_pause;
bool tx_pause; bool tx_pause;
bool mqprio_hw; bool mqprio_hw;
int fifo_bw[CPSW_TC_NUM];
int shp_cfg_speed;
u32 emac_port; u32 emac_port;
struct cpsw_common *cpsw; struct cpsw_common *cpsw;
}; };
...@@ -1082,6 +1090,38 @@ static void cpsw_set_slave_mac(struct cpsw_slave *slave, ...@@ -1082,6 +1090,38 @@ static void cpsw_set_slave_mac(struct cpsw_slave *slave,
slave_write(slave, mac_lo(priv->mac_addr), SA_LO); slave_write(slave, mac_lo(priv->mac_addr), SA_LO);
} }
static bool cpsw_shp_is_off(struct cpsw_priv *priv)
{
struct cpsw_common *cpsw = priv->cpsw;
struct cpsw_slave *slave;
u32 shift, mask, val;
val = readl_relaxed(&cpsw->regs->ptype);
slave = &cpsw->slaves[cpsw_slave_index(cpsw, priv)];
shift = CPSW_FIFO_SHAPE_EN_SHIFT + 3 * slave->slave_num;
mask = 7 << shift;
val = val & mask;
return !val;
}
static void cpsw_fifo_shp_on(struct cpsw_priv *priv, int fifo, int on)
{
struct cpsw_common *cpsw = priv->cpsw;
struct cpsw_slave *slave;
u32 shift, mask, val;
val = readl_relaxed(&cpsw->regs->ptype);
slave = &cpsw->slaves[cpsw_slave_index(cpsw, priv)];
shift = CPSW_FIFO_SHAPE_EN_SHIFT + 3 * slave->slave_num;
mask = (1 << --fifo) << shift;
val = on ? val | mask : val & ~mask;
writel_relaxed(val, &cpsw->regs->ptype);
}
static void _cpsw_adjust_link(struct cpsw_slave *slave, static void _cpsw_adjust_link(struct cpsw_slave *slave,
struct cpsw_priv *priv, bool *link) struct cpsw_priv *priv, bool *link)
{ {
...@@ -1121,6 +1161,12 @@ static void _cpsw_adjust_link(struct cpsw_slave *slave, ...@@ -1121,6 +1161,12 @@ static void _cpsw_adjust_link(struct cpsw_slave *slave,
mac_control |= BIT(4); mac_control |= BIT(4);
*link = true; *link = true;
if (priv->shp_cfg_speed &&
priv->shp_cfg_speed != slave->phy->speed &&
!cpsw_shp_is_off(priv))
dev_warn(priv->dev,
"Speed was changed, CBS shaper speeds are changed!");
} else { } else {
mac_control = 0; mac_control = 0;
/* disable forwarding */ /* disable forwarding */
...@@ -1590,6 +1636,178 @@ static int cpsw_tc_to_fifo(int tc, int num_tc) ...@@ -1590,6 +1636,178 @@ static int cpsw_tc_to_fifo(int tc, int num_tc)
return CPSW_FIFO_SHAPERS_NUM - tc; return CPSW_FIFO_SHAPERS_NUM - tc;
} }
static int cpsw_set_fifo_bw(struct cpsw_priv *priv, int fifo, int bw)
{
struct cpsw_common *cpsw = priv->cpsw;
u32 val = 0, send_pct, shift;
struct cpsw_slave *slave;
int pct = 0, i;
if (bw > priv->shp_cfg_speed * 1000)
goto err;
/* shaping has to stay enabled for highest fifos linearly
* and fifo bw no more then interface can allow
*/
slave = &cpsw->slaves[cpsw_slave_index(cpsw, priv)];
send_pct = slave_read(slave, SEND_PERCENT);
for (i = CPSW_FIFO_SHAPERS_NUM; i > 0; i--) {
if (!bw) {
if (i >= fifo || !priv->fifo_bw[i])
continue;
dev_warn(priv->dev, "Prev FIFO%d is shaped", i);
continue;
}
if (!priv->fifo_bw[i] && i > fifo) {
dev_err(priv->dev, "Upper FIFO%d is not shaped", i);
return -EINVAL;
}
shift = (i - 1) * 8;
if (i == fifo) {
send_pct &= ~(CPSW_PCT_MASK << shift);
val = DIV_ROUND_UP(bw, priv->shp_cfg_speed * 10);
if (!val)
val = 1;
send_pct |= val << shift;
pct += val;
continue;
}
if (priv->fifo_bw[i])
pct += (send_pct >> shift) & CPSW_PCT_MASK;
}
if (pct >= 100)
goto err;
slave_write(slave, send_pct, SEND_PERCENT);
priv->fifo_bw[fifo] = bw;
dev_warn(priv->dev, "set FIFO%d bw = %d\n", fifo,
DIV_ROUND_CLOSEST(val * priv->shp_cfg_speed, 100));
return 0;
err:
dev_err(priv->dev, "Bandwidth doesn't fit in tc configuration");
return -EINVAL;
}
static int cpsw_set_fifo_rlimit(struct cpsw_priv *priv, int fifo, int bw)
{
struct cpsw_common *cpsw = priv->cpsw;
struct cpsw_slave *slave;
u32 tx_in_ctl_rg, val;
int ret;
ret = cpsw_set_fifo_bw(priv, fifo, bw);
if (ret)
return ret;
slave = &cpsw->slaves[cpsw_slave_index(cpsw, priv)];
tx_in_ctl_rg = cpsw->version == CPSW_VERSION_1 ?
CPSW1_TX_IN_CTL : CPSW2_TX_IN_CTL;
if (!bw)
cpsw_fifo_shp_on(priv, fifo, bw);
val = slave_read(slave, tx_in_ctl_rg);
if (cpsw_shp_is_off(priv)) {
/* disable FIFOs rate limited queues */
val &= ~(0xf << CPSW_FIFO_RATE_EN_SHIFT);
/* set type of FIFO queues to normal priority mode */
val &= ~(3 << CPSW_FIFO_QUEUE_TYPE_SHIFT);
/* set type of FIFO queues to be rate limited */
if (bw)
val |= 2 << CPSW_FIFO_QUEUE_TYPE_SHIFT;
else
priv->shp_cfg_speed = 0;
}
/* toggle a FIFO rate limited queue */
if (bw)
val |= BIT(fifo + CPSW_FIFO_RATE_EN_SHIFT);
else
val &= ~BIT(fifo + CPSW_FIFO_RATE_EN_SHIFT);
slave_write(slave, val, tx_in_ctl_rg);
/* FIFO transmit shape enable */
cpsw_fifo_shp_on(priv, fifo, bw);
return 0;
}
/* Defaults:
* class A - prio 3
* class B - prio 2
* shaping for class A should be set first
*/
static int cpsw_set_cbs(struct net_device *ndev,
struct tc_cbs_qopt_offload *qopt)
{
struct cpsw_priv *priv = netdev_priv(ndev);
struct cpsw_common *cpsw = priv->cpsw;
struct cpsw_slave *slave;
int prev_speed = 0;
int tc, ret, fifo;
u32 bw = 0;
tc = netdev_txq_to_tc(priv->ndev, qopt->queue);
/* enable channels in backward order, as highest FIFOs must be rate
* limited first and for compliance with CPDMA rate limited channels
* that also used in bacward order. FIFO0 cannot be rate limited.
*/
fifo = cpsw_tc_to_fifo(tc, ndev->num_tc);
if (!fifo) {
dev_err(priv->dev, "Last tc%d can't be rate limited", tc);
return -EINVAL;
}
/* do nothing, it's disabled anyway */
if (!qopt->enable && !priv->fifo_bw[fifo])
return 0;
/* shapers can be set if link speed is known */
slave = &cpsw->slaves[cpsw_slave_index(cpsw, priv)];
if (slave->phy && slave->phy->link) {
if (priv->shp_cfg_speed &&
priv->shp_cfg_speed != slave->phy->speed)
prev_speed = priv->shp_cfg_speed;
priv->shp_cfg_speed = slave->phy->speed;
}
if (!priv->shp_cfg_speed) {
dev_err(priv->dev, "Link speed is not known");
return -1;
}
ret = pm_runtime_get_sync(cpsw->dev);
if (ret < 0) {
pm_runtime_put_noidle(cpsw->dev);
return ret;
}
bw = qopt->enable ? qopt->idleslope : 0;
ret = cpsw_set_fifo_rlimit(priv, fifo, bw);
if (ret) {
priv->shp_cfg_speed = prev_speed;
prev_speed = 0;
}
if (bw && prev_speed)
dev_warn(priv->dev,
"Speed was changed, CBS shaper speeds are changed!");
pm_runtime_put_sync(cpsw->dev);
return ret;
}
static int cpsw_ndo_open(struct net_device *ndev) static int cpsw_ndo_open(struct net_device *ndev)
{ {
struct cpsw_priv *priv = netdev_priv(ndev); struct cpsw_priv *priv = netdev_priv(ndev);
...@@ -2264,6 +2482,9 @@ static int cpsw_ndo_setup_tc(struct net_device *ndev, enum tc_setup_type type, ...@@ -2264,6 +2482,9 @@ static int cpsw_ndo_setup_tc(struct net_device *ndev, enum tc_setup_type type,
void *type_data) void *type_data)
{ {
switch (type) { switch (type) {
case TC_SETUP_QDISC_CBS:
return cpsw_set_cbs(ndev, type_data);
case TC_SETUP_QDISC_MQPRIO: case TC_SETUP_QDISC_MQPRIO:
return cpsw_set_mqprio(ndev, type_data); return cpsw_set_mqprio(ndev, type_data);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment