Commit 595be948 authored by Grant Likely's avatar Grant Likely Committed by Paul Mackerras

[POWERPC] Fix zImage-dtb.initrd build error

The pattern substitution rules were failing when used with zImage-dtb
targets.  If zImage-dtb.initrd was selected, the pattern substitution
would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which
caused the build to fail.

This renames zImage-dtb to dtbImage to avoid the problem entirely.
By not using the zImage prefix then is no potential for namespace
collisions.
Signed-off-by: default avatarGrant Likely <grant.likely@secretlab.ca>
Acked-by: default avatarGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
parent 95ff54f5
......@@ -155,7 +155,7 @@ all: zImage
CPPFLAGS_vmlinux.lds := -Upowerpc
BOOT_TARGETS = zImage zImage.initrd uImage treeImage.% cuImage.%
BOOT_TARGETS = zImage zImage.initrd uImage zImage% dtbImage% treeImage.% cuImage.%
PHONY += $(BOOT_TARGETS)
......
......@@ -186,7 +186,7 @@ quiet_cmd_wrap = WRAP $@
image-$(CONFIG_PPC_PSERIES) += zImage.pseries
image-$(CONFIG_PPC_MAPLE) += zImage.pseries
image-$(CONFIG_PPC_IBM_CELL_BLADE) += zImage.pseries
image-$(CONFIG_PPC_PS3) += zImage-dtb.ps3
image-$(CONFIG_PPC_PS3) += dtbImage.ps3
image-$(CONFIG_PPC_CELLEB) += zImage.pseries
image-$(CONFIG_PPC_CHRP) += zImage.chrp
image-$(CONFIG_PPC_EFIKA) += zImage.chrp
......@@ -205,7 +205,7 @@ image-$(CONFIG_DEFAULT_UIMAGE) += uImage
#
# Board ports in arch/powerpc/platform/40x/Kconfig
image-$(CONFIG_EP405) += zImage-dtb.ep405
image-$(CONFIG_EP405) += dtbImage.ep405
image-$(CONFIG_WALNUT) += treeImage.walnut
# Board ports in arch/powerpc/platform/44x/Kconfig
......@@ -220,9 +220,9 @@ image-$(CONFIG_WARP) += cuImage.warp
# Board ports in arch/powerpc/platform/8xx/Kconfig
image-$(CONFIG_PPC_MPC86XADS) += cuImage.mpc866ads
image-$(CONFIG_PPC_MPC885ADS) += cuImage.mpc885ads
image-$(CONFIG_PPC_EP88XC) += zImage-dtb.ep88xc
image-$(CONFIG_PPC_EP88XC) += dtbImage.ep88xc
image-$(CONFIG_PPC_ADDER875) += cuImage.adder875-uboot \
zImage-dtb.adder875-redboot
dtbImage.adder875-redboot
# Board ports in arch/powerpc/platform/52xx/Kconfig
image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200 cuImage.lite5200b
......@@ -230,7 +230,7 @@ image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200 cuImage.lite5200b
# Board ports in arch/powerpc/platform/82xx/Kconfig
image-$(CONFIG_MPC8272_ADS) += cuImage.mpc8272ads
image-$(CONFIG_PQ2FADS) += cuImage.pq2fads
image-$(CONFIG_EP8248E) += zImage-dtb.ep8248e
image-$(CONFIG_EP8248E) += dtbImage.ep8248e
# Board ports in arch/powerpc/platform/83xx/Kconfig
image-$(CONFIG_MPC832x_MDS) += cuImage.mpc832x_mds
......@@ -268,7 +268,8 @@ endif
initrd- := $(patsubst zImage%, zImage.initrd%, $(image-n) $(image-))
initrd-y := $(patsubst zImage%, zImage.initrd%, \
$(patsubst treeImage%, treeImage.initrd%, $(image-y)))
$(patsubst dtbImage%, dtbImage.initrd%, \
$(patsubst treeImage%, treeImage.initrd%, $(image-y))))
initrd-y := $(filter-out $(image-y), $(initrd-y))
targets += $(image-y) $(initrd-y)
......@@ -283,10 +284,11 @@ $(obj)/zImage.initrd.%: vmlinux $(wrapperbits)
$(obj)/zImage.%: vmlinux $(wrapperbits)
$(call if_changed,wrap,$*)
$(obj)/zImage-dtb.initrd.%: vmlinux $(wrapperbits) $(dtstree)/%.dts
# dtbImage% - a dtbImage is a zImage with an embedded device tree blob
$(obj)/dtbImage.initrd.%: vmlinux $(wrapperbits) $(dtstree)/%.dts
$(call if_changed,wrap,$*,$(dtstree)/$*.dts,,$(obj)/ramdisk.image.gz)
$(obj)/zImage-dtb.%: vmlinux $(wrapperbits) $(dtstree)/%.dts
$(obj)/dtbImage.%: vmlinux $(wrapperbits) $(dtstree)/%.dts
$(call if_changed,wrap,$*,$(dtstree)/$*.dts)
# This cannot be in the root of $(src) as the zImage rule always adds a $(obj)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment