Commit 5a07a30c authored by Venkatesh Pallipadi's avatar Venkatesh Pallipadi Committed by Linus Torvalds

[PATCH] i386/x86-64: Remove sub jiffy profile timer support

Remove the finer control of local APIC timer. We cannot provide a sub-jiffy
control like this when we use broadcast from external timer in place of
local APIC. Instead of removing this only on systems that may end up using
broadcast from external timer (due to C3), I am going the
"I'm feeling lucky" way to remove this fully. Basically, I am not sure about
usefulness of this code today. Few other architectures also don't seem to
support this today.

If you are using profiling and fine grained control and don't like this going
away in normal case, yell at me right now.
Signed-off-by: default avatarVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: default avatarAndi Kleen <ak@suse.de>
Signed-off-by: default avatarLinus Torvalds <torvalds@osdl.org>
parent 01b8faae
......@@ -92,10 +92,6 @@ void __init apic_intr_init(void)
/* Using APIC to generate smp_local_timer_interrupt? */
int using_apic_timer = 0;
static DEFINE_PER_CPU(int, prof_multiplier) = 1;
static DEFINE_PER_CPU(int, prof_old_multiplier) = 1;
static DEFINE_PER_CPU(int, prof_counter) = 1;
static int enabled_via_apicbase;
void enable_NMI_through_LVT0 (void * dummy)
......@@ -1092,34 +1088,6 @@ void enable_APIC_timer(void)
}
}
/*
* the frequency of the profiling timer can be changed
* by writing a multiplier value into /proc/profile.
*/
int setup_profiling_timer(unsigned int multiplier)
{
int i;
/*
* Sanity check. [at least 500 APIC cycles should be
* between APIC interrupts as a rule of thumb, to avoid
* irqs flooding us]
*/
if ( (!multiplier) || (calibration_result/multiplier < 500))
return -EINVAL;
/*
* Set the new multiplier for each CPU. CPUs don't start using the
* new values until the next timer interrupt in which they do process
* accounting. At that time they also adjust their APIC timers
* accordingly.
*/
for (i = 0; i < NR_CPUS; ++i)
per_cpu(prof_multiplier, i) = multiplier;
return 0;
}
#undef APIC_DIVISOR
/*
......@@ -1134,32 +1102,10 @@ int setup_profiling_timer(unsigned int multiplier)
inline void smp_local_timer_interrupt(struct pt_regs * regs)
{
int cpu = smp_processor_id();
profile_tick(CPU_PROFILING, regs);
if (--per_cpu(prof_counter, cpu) <= 0) {
/*
* The multiplier may have changed since the last time we got
* to this point as a result of the user writing to
* /proc/profile. In this case we need to adjust the APIC
* timer accordingly.
*
* Interrupts are already masked off at this point.
*/
per_cpu(prof_counter, cpu) = per_cpu(prof_multiplier, cpu);
if (per_cpu(prof_counter, cpu) !=
per_cpu(prof_old_multiplier, cpu)) {
__setup_APIC_LVTT(
calibration_result/
per_cpu(prof_counter, cpu));
per_cpu(prof_old_multiplier, cpu) =
per_cpu(prof_counter, cpu);
}
#ifdef CONFIG_SMP
update_process_times(user_mode_vm(regs));
update_process_times(user_mode_vm(regs));
#endif
}
/*
* We take the 'long' return path, and there every subsystem
......@@ -1206,6 +1152,11 @@ fastcall void smp_apic_timer_interrupt(struct pt_regs *regs)
irq_exit();
}
int setup_profiling_timer(unsigned int multiplier)
{
return -EINVAL;
}
/*
* This interrupt should _never_ happen with our APIC/SMP architecture
*/
......
......@@ -41,10 +41,6 @@ int disable_apic_timer __initdata;
/* Using APIC to generate smp_local_timer_interrupt? */
int using_apic_timer = 0;
static DEFINE_PER_CPU(int, prof_multiplier) = 1;
static DEFINE_PER_CPU(int, prof_old_multiplier) = 1;
static DEFINE_PER_CPU(int, prof_counter) = 1;
static void apic_pm_activate(void);
void enable_NMI_through_LVT0 (void * dummy)
......@@ -805,32 +801,9 @@ void enable_APIC_timer(void)
}
}
/*
* the frequency of the profiling timer can be changed
* by writing a multiplier value into /proc/profile.
*/
int setup_profiling_timer(unsigned int multiplier)
{
int i;
/*
* Sanity check. [at least 500 APIC cycles should be
* between APIC interrupts as a rule of thumb, to avoid
* irqs flooding us]
*/
if ( (!multiplier) || (calibration_result/multiplier < 500))
return -EINVAL;
/*
* Set the new multiplier for each CPU. CPUs don't start using the
* new values until the next timer interrupt in which they do process
* accounting. At that time they also adjust their APIC timers
* accordingly.
*/
for (i = 0; i < NR_CPUS; ++i)
per_cpu(prof_multiplier, i) = multiplier;
return 0;
return -EINVAL;
}
#ifdef CONFIG_X86_MCE_AMD
......@@ -857,32 +830,10 @@ void setup_threshold_lvt(unsigned long lvt_off)
void smp_local_timer_interrupt(struct pt_regs *regs)
{
int cpu = smp_processor_id();
profile_tick(CPU_PROFILING, regs);
if (--per_cpu(prof_counter, cpu) <= 0) {
/*
* The multiplier may have changed since the last time we got
* to this point as a result of the user writing to
* /proc/profile. In this case we need to adjust the APIC
* timer accordingly.
*
* Interrupts are already masked off at this point.
*/
per_cpu(prof_counter, cpu) = per_cpu(prof_multiplier, cpu);
if (per_cpu(prof_counter, cpu) !=
per_cpu(prof_old_multiplier, cpu)) {
__setup_APIC_LVTT(calibration_result/
per_cpu(prof_counter, cpu));
per_cpu(prof_old_multiplier, cpu) =
per_cpu(prof_counter, cpu);
}
#ifdef CONFIG_SMP
update_process_times(user_mode(regs));
update_process_times(user_mode(regs));
#endif
}
/*
* We take the 'long' return path, and there every subsystem
* grabs the appropriate locks (kernel lock/ irq lock).
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment