Staging: wilc1000: Boolean tests don't need comparisons

This patch removes unwanted true and false from boolean tests.
Signed-off-by: Abdul Hussain <habdul@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/wilc1000/coreconfigurator.c

@@ -1716,7 +1716,7 @@ s32 ParseResponse(u8 *resp, tstrWID *pstrWIDcfgResult)
 			idx++;
 		}
 		idx += 3;
-		if ((u16WIDid == g_wid_num) && (num_wid_processed == false)) {
+		if ((u16WIDid == g_wid_num) && (!num_wid_processed)) {
 			num_wid_processed = true;
 
 			if (-2 == further_process_response(&resp[idx], u16WIDid, cfg_len, true, 0, &pstrWIDcfgResult[ResCnt])) {
@@ -1922,7 +1922,7 @@ s32 ConfigWaitResponse(char *pcRespBuffer, s32 s32MaxRespBuffLen, s32 *ps32Bytes
 	 * gstrConfigPktInfo.bRespRequired = bRespRequired;*/
 
 
-	if (gstrConfigPktInfo.bRespRequired == true) {
+	if (gstrConfigPktInfo.bRespRequired) {
 		down(&SemHandlePktResp);
 
 		*ps32BytesRead = gstrConfigPktInfo.s32BytesRead;
@@ -1983,7 +1983,7 @@ s32 SendConfigPkt(u8 u8Mode, tstrWID *pstrWIDs,
 	ConfigWaitResponse(gps8ConfigPacket, MAX_PACKET_BUFF_SIZE, &s32RcvdRespLen, bRespRequired);
 
 
-	if (bRespRequired == true)	{
+	if (bRespRequired)	{
 		/* If the operating Mode is GET, then we expect a response frame from */
 		/* the driver. Hence start listening to the port for response         */
 		if (g_oper_mode == GET_CFG) {
@@ -2020,7 +2020,7 @@ s32 ConfigProvideResponse(char *pcRespBuffer, s32 s32RespLen)
 {
 	s32 s32Error = WILC_SUCCESS;
 
-	if (gstrConfigPktInfo.bRespRequired == true) {
+	if (gstrConfigPktInfo.bRespRequired) {
 		if (s32RespLen <= gstrConfigPktInfo.s32MaxRespBuffLen) {
 			WILC_memcpy(gstrConfigPktInfo.pcRespBuffer, pcRespBuffer, s32RespLen);
 			gstrConfigPktInfo.s32BytesRead = s32RespLen;

drivers/staging/wilc1000/linux_mon.c

@@ -452,7 +452,7 @@ void WILC_mgm_HOSTAPD_ACK(void *priv, bool bStatus)
 		cb_hdr->rate = 5; /* txrate->bitrate / 5; */
 
 
-		if (true == bStatus) {
+		if (bStatus) {
 			/* success */
 			cb_hdr->tx_flags = IEEE80211_RADIOTAP_F_TX_RTS;
 		} else {

drivers/staging/wilc1000/linux_wlan.c

@@ -309,7 +309,7 @@ static int dev_state_ev_handler(struct notifier_block *this, unsigned long event
 
 
 
-		if (bEnablePS	 == true)
+		if (bEnablePS)
 			host_int_set_power_mgmt((WILC_WFIDrvHandle)pstrWFIDrv, 1, 0);
 
 		PRINT_D(GENERIC_DBG, "[%s] Up IP\n", dev_iface->ifa_label);

drivers/staging/wilc1000/wilc_wfi_cfgoperations.c

@@ -624,7 +624,7 @@ static void CfgConnectResult(tenuConnDisconnEvent enuConnDisconnEvent,
 				}
 			}
 
-			if (bNeedScanRefresh == true) {
+			if (bNeedScanRefresh) {
 				/*BugID_5418*/
 				/*Also, refrsh DIRECT- results if */
 				refresh_scan(priv, 1, true);
@@ -2817,7 +2817,7 @@ int WILC_WFI_set_power_mgmt(struct wiphy *wiphy, struct net_device *dev,
 		return -EIO;
 	}
 
-	if (bEnablePS	 == true)
+	if (bEnablePS)
 		host_int_set_power_mgmt(priv->hWILCWFIDrv, enabled, timeout);
 
 

drivers/staging/wilc1000/wilc_wlan.c

@@ -559,7 +559,7 @@ static int wilc_wlan_txq_add_net_pkt(void *priv, uint8_t *buffer, uint32_t buffe
 #ifdef TCP_ACK_FILTER
 	tqe->tcp_PendingAck_index = NOT_TCP_ACK;
 #ifdef TCP_ENHANCEMENTS
-	if (is_TCP_ACK_Filter_Enabled() == true)
+	if (is_TCP_ACK_Filter_Enabled())
 #endif
 	tcp_process(tqe);
 #endif
@@ -2337,7 +2337,7 @@ u16 Set_machw_change_vir_if(bool bValue)
 		PRINT_ER("Error while Reading reg WILC_CHANGING_VIR_IF\n");
 	}
 
-	if (bValue == true) {
+	if (bValue) {
 		reg |= (BIT31);
 	} else {
 		reg &= ~(BIT31);