Commit 5c132323 authored by Vijay Viswanath's avatar Vijay Viswanath Committed by Ulf Hansson

mmc: sdhci-msm: support voltage pad switching

The PADs for SD card are dual-voltage that support 3v/1.8v. Those PADs
have a control signal  (io_pad_pwr_switch/mode18 ) that indicates
whether the PAD works in 3v or 1.8v.

SDHC core on msm platforms should have IO_PAD_PWR_SWITCH bit set/unset
based on actual voltage used for IO lines. So when power irq is
triggered for io high or io low, the driver should check the voltages
supported and set the pad accordingly.
Signed-off-by: default avatarKrishna Konda <kkonda@codeaurora.org>
Signed-off-by: default avatarVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: default avatarVijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: default avatarDouglas Anderson <dianders@chromium.org>
Acked-by: default avatarBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: default avatarUlf Hansson <ulf.hansson@linaro.org>
parent ac06fba1
......@@ -78,12 +78,15 @@
#define CORE_HC_MCLK_SEL_DFLT (2 << 8)
#define CORE_HC_MCLK_SEL_HS400 (3 << 8)
#define CORE_HC_MCLK_SEL_MASK (3 << 8)
#define CORE_IO_PAD_PWR_SWITCH_EN (1 << 15)
#define CORE_IO_PAD_PWR_SWITCH (1 << 16)
#define CORE_HC_SELECT_IN_EN BIT(18)
#define CORE_HC_SELECT_IN_HS400 (6 << 19)
#define CORE_HC_SELECT_IN_MASK (7 << 19)
#define CORE_3_0V_SUPPORT (1 << 25)
#define CORE_1_8V_SUPPORT (1 << 26)
#define CORE_VOLT_SUPPORT (CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT)
#define CORE_CSR_CDC_CTLR_CFG0 0x130
#define CORE_SW_TRIG_FULL_CALIB BIT(16)
......@@ -1109,7 +1112,7 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq)
u32 irq_status, irq_ack = 0;
int retry = 10;
u32 pwr_state = 0, io_level = 0;
u32 config;
irq_status = readl_relaxed(msm_host->core_mem + CORE_PWRCTL_STATUS);
irq_status &= INT_MASK;
......@@ -1166,6 +1169,38 @@ static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq)
*/
writel_relaxed(irq_ack, msm_host->core_mem + CORE_PWRCTL_CTL);
/*
* If we don't have info regarding the voltage levels supported by
* regulators, don't change the IO PAD PWR SWITCH.
*/
if (msm_host->caps_0 & CORE_VOLT_SUPPORT) {
u32 new_config;
/*
* We should unset IO PAD PWR switch only if the register write
* can set IO lines high and the regulator also switches to 3 V.
* Else, we should keep the IO PAD PWR switch set.
* This is applicable to certain targets where eMMC vccq supply
* is only 1.8V. In such targets, even during REQ_IO_HIGH, the
* IO PAD PWR switch must be kept set to reflect actual
* regulator voltage. This way, during initialization of
* controllers with only 1.8V, we will set the IO PAD bit
* without waiting for a REQ_IO_LOW.
*/
config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
new_config = config;
if ((io_level & REQ_IO_HIGH) &&
(msm_host->caps_0 & CORE_3_0V_SUPPORT))
new_config &= ~CORE_IO_PAD_PWR_SWITCH;
else if ((io_level & REQ_IO_LOW) ||
(msm_host->caps_0 & CORE_1_8V_SUPPORT))
new_config |= CORE_IO_PAD_PWR_SWITCH;
if (config ^ new_config)
writel_relaxed(new_config,
host->ioaddr + CORE_VENDOR_SPEC);
}
if (pwr_state)
msm_host->curr_pwr_state = pwr_state;
if (io_level)
......@@ -1322,7 +1357,8 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
{
struct mmc_host *mmc = msm_host->mmc;
struct regulator *supply = mmc->supply.vqmmc;
u32 caps = 0;
u32 caps = 0, config;
struct sdhci_host *host = mmc_priv(mmc);
if (!IS_ERR(mmc->supply.vqmmc)) {
if (regulator_is_supported_voltage(supply, 1700000, 1950000))
......@@ -1335,6 +1371,23 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
mmc_hostname(mmc));
}
if (caps) {
/*
* Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH
* bit can be used as required later on.
*/
u32 io_level = msm_host->curr_io_level;
config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
config |= CORE_IO_PAD_PWR_SWITCH_EN;
if ((io_level & REQ_IO_HIGH) && (caps & CORE_3_0V_SUPPORT))
config &= ~CORE_IO_PAD_PWR_SWITCH;
else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT))
config |= CORE_IO_PAD_PWR_SWITCH;
writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
}
msm_host->caps_0 |= caps;
pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment