w1: ds2482: cosmetic fixes after 54865314

We have a helper function ds2482_calculate_config() which is calculating
the config value, so just use it instead of passing the same variable
in all calls to this function.

Also fixes the placement of module parameters to match with:
50fa2951 (w1: Organize driver source to natural/common order)
by Andrew F. Davis
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/w1/masters/ds2482.c

@@ -37,6 +37,11 @@ module_param_named(active_pullup, ds2482_active_pullup, int, 0644);
 MODULE_PARM_DESC(active_pullup, "Active pullup (apply to all buses): " \
 				"0-disable, 1-enable (default)");
 
+/* extra configurations - e.g. 1WS */
+static int extra_config;
+module_param(extra_config, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(extra_config, "Extra Configuration settings 1=APU,2=PPM,3=SPU,8=1WS");
+
 /**
  * The DS2482 registers - there are 3 registers that are addressed by a read
  * pointer. The read pointer is set by the last command executed.
@@ -70,8 +75,6 @@ MODULE_PARM_DESC(active_pullup, "Active pullup (apply to all buses): " \
 #define DS2482_REG_CFG_PPM		0x02	/* presence pulse masking */
 #define DS2482_REG_CFG_APU		0x01	/* active pull-up */
 
-/* extra configurations - e.g. 1WS */
-static int extra_config;
 
 /**
  * Write and verify codes for the CHANNEL_SELECT command (DS2482-800 only).
@@ -130,6 +133,8 @@ struct ds2482_data {
  */
 static inline u8 ds2482_calculate_config(u8 conf)
 {
+	conf |= extra_config;
+
 	if (ds2482_active_pullup)
 		conf |= DS2482_REG_CFG_APU;
 
@@ -405,7 +410,7 @@ static u8 ds2482_w1_reset_bus(void *data)
 		/* If the chip did reset since detect, re-config it */
 		if (err & DS2482_REG_STS_RST)
 			ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG,
-					ds2482_calculate_config(extra_config));
+					     ds2482_calculate_config(0x00));
 	}
 
 	mutex_unlock(&pdev->access_lock);
@@ -431,7 +436,8 @@ static u8 ds2482_w1_set_pullup(void *data, int delay)
 		ds2482_wait_1wire_idle(pdev);
 		/* note: it seems like both SPU and APU have to be set! */
 		retval = ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG,
-			ds2482_calculate_config(extra_config|DS2482_REG_CFG_SPU|DS2482_REG_CFG_APU));
+			ds2482_calculate_config(DS2482_REG_CFG_SPU |
+						DS2482_REG_CFG_APU));
 		ds2482_wait_1wire_idle(pdev);
 	}
 
@@ -484,7 +490,7 @@ static int ds2482_probe(struct i2c_client *client,
 
 	/* Set all config items to 0 (off) */
 	ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG,
-		ds2482_calculate_config(extra_config));
+		ds2482_calculate_config(0x00));
 
 	mutex_init(&data->access_lock);
 
@@ -559,7 +565,5 @@ module_i2c_driver(ds2482_driver);
 
 MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
 MODULE_DESCRIPTION("DS2482 driver");
-module_param(extra_config, int, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(extra_config, "Extra Configuration settings 1=APU,2=PPM,3=SPU,8=1WS");
 
 MODULE_LICENSE("GPL");