[PATCH] ARM: 2812/1: OMAP update 7c/11: Move arch-omap to plat-omap

Patch from Tony Lindgren

This patch move common OMAP code from arch-omap to plat-omap
directory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/plat-omap/Kconfig

+if ARCH_OMAP
+
+menu "TI OMAP Implementations"
+
+config ARCH_OMAP_OTG
+	bool
+
+choice
+	prompt "OMAP System Type"
+	default ARCH_OMAP1
+
+config ARCH_OMAP1
+	bool "TI OMAP1"
+
+config ARCH_OMAP2
+	bool "TI OMAP2"
+
+endchoice
+
+comment "OMAP Feature Selections"
+
+config OMAP_MUX
+	bool "OMAP multiplexing support"
+        depends on ARCH_OMAP
+	default y
+        help
+          Pin multiplexing support for OMAP boards. If your bootloader
+          sets the multiplexing correctly, say N. Otherwise, or if unsure,
+          say Y.
+
+config OMAP_MUX_DEBUG
+	bool "Multiplexing debug output"
+        depends on OMAP_MUX
+        default n
+        help
+          Makes the multiplexing functions print out a lot of debug info.
+          This is useful if you want to find out the correct values of the
+          multiplexing registers.
+
+config OMAP_MUX_WARNINGS
+	bool "Warn about pins the bootloader didn't set up"
+        depends on OMAP_MUX
+        default y
+        help
+	  Choose Y here to warn whenever driver initialization logic needs
+	  to change the pin multiplexing setup.  When there are no warnings
+	  printed, it's safe to deselect OMAP_MUX for your product.
+
+choice
+        prompt "System timer"
+	default OMAP_MPU_TIMER
+
+config OMAP_MPU_TIMER
+	bool "Use mpu timer"
+	help
+	  Select this option if you want to use the OMAP mpu timer. This
+	  timer provides more intra-tick resolution than the 32KHz timer,
+	  but consumes more power.
+
+config OMAP_32K_TIMER
+	bool "Use 32KHz timer"
+	depends on ARCH_OMAP16XX
+	help
+	  Select this option if you want to enable the OMAP 32KHz timer.
+	  This timer saves power compared to the OMAP_MPU_TIMER, and has
+	  support for no tick during idle. The 32KHz timer provides less
+	  intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
+	  currently only available for OMAP-16xx.
+
+endchoice
+
+config OMAP_32K_TIMER_HZ
+       int "Kernel internal timer frequency for 32KHz timer"
+       range 32 1024
+       depends on OMAP_32K_TIMER
+       default "128"
+       help
+	  Kernel internal timer frequency should be a divisor of 32768,
+	  such as 64 or 128.
+
+choice
+	prompt "Low-level debug console UART"
+	depends on ARCH_OMAP
+	default OMAP_LL_DEBUG_UART1
+
+config OMAP_LL_DEBUG_UART1
+	bool "UART1"
+
+config OMAP_LL_DEBUG_UART2
+	bool "UART2"
+
+config OMAP_LL_DEBUG_UART3
+	bool "UART3"
+
+endchoice
+
+endmenu
+
+endif

arch/arm/plat-omap/Makefile

+#
+# Makefile for the linux kernel.
+#
+
+# Common support
+obj-y := common.o dma.o clock.o mux.o gpio.o mcbsp.o usb.o
+obj-m :=
+obj-n :=
+obj-  :=
+
+# OCPI interconnect support for 1710, 1610 and 5912
+obj-$(CONFIG_ARCH_OMAP16XX) += ocpi.o
+
+# Power Management
+obj-$(CONFIG_PM) += pm.o sleep.o
+

arch/arm/plat-omap/common.c

+/*
+ * linux/arch/arm/plat-omap/common.c
+ *
+ * Code common to all OMAP machines.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <linux/console.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/serial_reg.h>
+
+#include <asm/hardware.h>
+#include <asm/system.h>
+#include <asm/pgtable.h>
+#include <asm/mach/map.h>
+#include <asm/hardware/clock.h>
+#include <asm/io.h>
+#include <asm/mach-types.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/mux.h>
+#include <asm/arch/fpga.h>
+
+#include "clock.h"
+
+#define NO_LENGTH_CHECK 0xffffffff
+
+extern int omap_bootloader_tag_len;
+extern u8 omap_bootloader_tag[];
+
+struct omap_board_config_kernel *omap_board_config;
+int omap_board_config_size = 0;
+
+static const void *get_config(u16 tag, size_t len, int skip, size_t *len_out)
+{
+	struct omap_board_config_kernel *kinfo = NULL;
+	int i;
+
+#ifdef CONFIG_OMAP_BOOT_TAG
+	struct omap_board_config_entry *info = NULL;
+
+	if (omap_bootloader_tag_len > 4)
+		info = (struct omap_board_config_entry *) omap_bootloader_tag;
+	while (info != NULL) {
+		u8 *next;
+
+		if (info->tag == tag) {
+			if (skip == 0)
+				break;
+			skip--;
+		}
+
+		if ((info->len & 0x03) != 0) {
+			/* We bail out to avoid an alignment fault */
+			printk(KERN_ERR "OMAP peripheral config: Length (%d) not word-aligned (tag %04x)\n",
+			       info->len, info->tag);
+			return NULL;
+		}
+		next = (u8 *) info + sizeof(*info) + info->len;
+		if (next >= omap_bootloader_tag + omap_bootloader_tag_len)
+			info = NULL;
+		else
+			info = (struct omap_board_config_entry *) next;
+	}
+	if (info != NULL) {
+		/* Check the length as a lame attempt to check for
+		 * binary inconsistancy. */
+		if (len != NO_LENGTH_CHECK) {
+			/* Word-align len */
+			if (len & 0x03)
+				len = (len + 3) & ~0x03;
+			if (info->len != len) {
+				printk(KERN_ERR "OMAP peripheral config: Length mismatch with tag %x (want %d, got %d)\n",
+				       tag, len, info->len);
+				return NULL;
+			}
+		}
+		if (len_out != NULL)
+			*len_out = info->len;
+		return info->data;
+	}
+#endif
+	/* Try to find the config from the board-specific structures
+	 * in the kernel. */
+	for (i = 0; i < omap_board_config_size; i++) {
+		if (omap_board_config[i].tag == tag) {
+			kinfo = &omap_board_config[i];
+			break;
+		}
+	}
+	if (kinfo == NULL)
+		return NULL;
+	return kinfo->data;
+}
+
+const void *__omap_get_config(u16 tag, size_t len, int nr)
+{
+        return get_config(tag, len, nr, NULL);
+}
+EXPORT_SYMBOL(__omap_get_config);
+
+const void *omap_get_var_config(u16 tag, size_t *len)
+{
+        return get_config(tag, NO_LENGTH_CHECK, 0, len);
+}
+EXPORT_SYMBOL(omap_get_var_config);
+
+static int __init omap_add_serial_console(void)
+{
+	const struct omap_serial_console_config *info;
+
+	info = omap_get_config(OMAP_TAG_SERIAL_CONSOLE,
+			       struct omap_serial_console_config);
+	if (info != NULL && info->console_uart) {
+		static char speed[11], *opt = NULL;
+
+		if (info->console_speed) {
+			snprintf(speed, sizeof(speed), "%u", info->console_speed);
+			opt = speed;
+		}
+		return add_preferred_console("ttyS", info->console_uart - 1, opt);
+	}
+	return 0;
+}
+console_initcall(omap_add_serial_console);

arch/arm/plat-omap/common.h

+/*
+ * linux/arch/arm/plat-omap/common.h
+ *
+ * Header for code common to all OMAP machines.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the  GNU General Public License along
+ * with this program; if not, write  to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ARCH_ARM_MACH_OMAP_COMMON_H
+#define __ARCH_ARM_MACH_OMAP_COMMON_H
+
+struct sys_timer;
+
+extern void omap_map_common_io(void);
+extern struct sys_timer omap_timer;
+extern void omap_serial_init(int ports[]);
+
+#endif /* __ARCH_ARM_MACH_OMAP_COMMON_H */

arch/arm/plat-omap/mux.c

+/*
+ * linux/arch/arm/plat-omap/mux.c
+ *
+ * Utility to set the Omap MUX and PULL_DWN registers from a table in mux.h
+ *
+ * Copyright (C) 2003 Nokia Corporation
+ *
+ * Written by Tony Lindgren <tony.lindgren@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <asm/system.h>
+#include <asm/io.h>
+#include <linux/spinlock.h>
+
+#define __MUX_C__
+#include <asm/arch/mux.h>
+
+#ifdef CONFIG_OMAP_MUX
+
+/*
+ * Sets the Omap MUX and PULL_DWN registers based on the table
+ */
+int __init_or_module
+omap_cfg_reg(const reg_cfg_t reg_cfg)
+{
+	static DEFINE_SPINLOCK(mux_spin_lock);
+
+	unsigned long flags;
+	reg_cfg_set *cfg;
+	unsigned int reg_orig = 0, reg = 0, pu_pd_orig = 0, pu_pd = 0,
+		pull_orig = 0, pull = 0;
+	unsigned int mask, warn = 0;
+
+	if (reg_cfg > ARRAY_SIZE(reg_cfg_table)) {
+		printk(KERN_ERR "MUX: reg_cfg %d\n", reg_cfg);
+		return -EINVAL;
+	}
+
+	cfg = &reg_cfg_table[reg_cfg];
+
+	/*
+	 * We do a pretty long section here with lock on, but pin muxing
+	 * should only happen on driver init for each driver, so it's not time
+	 * critical.
+	 */
+	spin_lock_irqsave(&mux_spin_lock, flags);
+
+	/* Check the mux register in question */
+	if (cfg->mux_reg) {
+		unsigned	tmp1, tmp2;
+
+		reg_orig = omap_readl(cfg->mux_reg);
+
+		/* The mux registers always seem to be 3 bits long */
+		mask = (0x7 << cfg->mask_offset);
+		tmp1 = reg_orig & mask;
+		reg = reg_orig & ~mask;
+
+		tmp2 = (cfg->mask << cfg->mask_offset);
+		reg |= tmp2;
+
+		if (tmp1 != tmp2)
+			warn = 1;
+
+		omap_writel(reg, cfg->mux_reg);
+	}
+
+	/* Check for pull up or pull down selection on 1610 */
+	if (!cpu_is_omap1510()) {
+		if (cfg->pu_pd_reg && cfg->pull_val) {
+			pu_pd_orig = omap_readl(cfg->pu_pd_reg);
+			mask = 1 << cfg->pull_bit;
+
+			if (cfg->pu_pd_val) {
+				if (!(pu_pd_orig & mask))
+					warn = 1;
+				/* Use pull up */
+				pu_pd = pu_pd_orig | mask;
+			} else {
+				if (pu_pd_orig & mask)
+					warn = 1;
+				/* Use pull down */
+				pu_pd = pu_pd_orig & ~mask;
+			}
+			omap_writel(pu_pd, cfg->pu_pd_reg);
+		}
+	}
+
+	/* Check for an associated pull down register */
+	if (cfg->pull_reg) {
+		pull_orig = omap_readl(cfg->pull_reg);
+		mask = 1 << cfg->pull_bit;
+
+		if (cfg->pull_val) {
+			if (pull_orig & mask)
+				warn = 1;
+			/* Low bit = pull enabled */
+			pull = pull_orig & ~mask;
+		} else {
+			if (!(pull_orig & mask))
+				warn = 1;
+			/* High bit = pull disabled */
+			pull = pull_orig | mask;
+		}
+
+		omap_writel(pull, cfg->pull_reg);
+	}
+
+	if (warn) {
+#ifdef CONFIG_OMAP_MUX_WARNINGS
+		printk(KERN_WARNING "MUX: initialized %s\n", cfg->name);
+#endif
+	}
+
+#ifdef CONFIG_OMAP_MUX_DEBUG
+	if (cfg->debug || warn) {
+		printk("MUX: Setting register %s\n", cfg->name);
+		printk("      %s (0x%08x) = 0x%08x -> 0x%08x\n",
+		       cfg->mux_reg_name, cfg->mux_reg, reg_orig, reg);
+
+		if (!cpu_is_omap1510()) {
+			if (cfg->pu_pd_reg && cfg->pull_val) {
+				printk("      %s (0x%08x) = 0x%08x -> 0x%08x\n",
+				       cfg->pu_pd_name, cfg->pu_pd_reg,
+				       pu_pd_orig, pu_pd);
+			}
+		}
+
+		if (cfg->pull_reg)
+			printk("      %s (0x%08x) = 0x%08x -> 0x%08x\n",
+			       cfg->pull_name, cfg->pull_reg, pull_orig, pull);
+	}
+#endif
+
+	spin_unlock_irqrestore(&mux_spin_lock, flags);
+
+#ifdef CONFIG_OMAP_MUX_ERRORS
+	return warn ? -ETXTBSY : 0;
+#else
+	return 0;
+#endif
+}
+
+EXPORT_SYMBOL(omap_cfg_reg);
+
+#endif	/* CONFIG_OMAP_MUX */

arch/arm/plat-omap/ocpi.c

+/*
+ * linux/arch/arm/plat-omap/ocpi.c
+ *
+ * Minimal OCP bus support for omap16xx
+ *
+ * Copyright (C) 2003 - 2005 Nokia Corporation
+ * Written by Tony Lindgren <tony@atomide.com>
+ *
+ * Modified for clock framework by Paul Mundt <paul.mundt@nokia.com>.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/version.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/err.h>
+
+#include <asm/io.h>
+#include <asm/hardware/clock.h>
+#include <asm/arch/hardware.h>
+
+#define OCPI_BASE		0xfffec320
+#define OCPI_FAULT		(OCPI_BASE + 0x00)
+#define OCPI_CMD_FAULT		(OCPI_BASE + 0x04)
+#define OCPI_SINT0		(OCPI_BASE + 0x08)
+#define OCPI_TABORT		(OCPI_BASE + 0x0c)
+#define OCPI_SINT1		(OCPI_BASE + 0x10)
+#define OCPI_PROT		(OCPI_BASE + 0x14)
+#define OCPI_SEC		(OCPI_BASE + 0x18)
+
+/* USB OHCI OCPI access error registers */
+#define HOSTUEADDR	0xfffba0e0
+#define HOSTUESTATUS	0xfffba0e4
+
+static struct clk *ocpi_ck;
+
+/*
+ * Enables device access to OMAP buses via the OCPI bridge
+ * FIXME: Add locking
+ */
+int ocpi_enable(void)
+{
+	unsigned int val;
+
+	if (!cpu_is_omap16xx())
+		return -ENODEV;
+
+	/* Make sure there's clock for OCPI */
+	clk_enable(ocpi_ck);
+
+	/* Enable access for OHCI in OCPI */
+	val = omap_readl(OCPI_PROT);
+	val &= ~0xff;
+	//val &= (1 << 0);	/* Allow access only to EMIFS */
+	omap_writel(val, OCPI_PROT);
+
+	val = omap_readl(OCPI_SEC);
+	val &= ~0xff;
+	omap_writel(val, OCPI_SEC);
+
+	return 0;
+}
+EXPORT_SYMBOL(ocpi_enable);
+
+static int __init omap_ocpi_init(void)
+{
+	if (!cpu_is_omap16xx())
+		return -ENODEV;
+
+	ocpi_ck = clk_get(NULL, "l3_ocpi_ck");
+	if (IS_ERR(ocpi_ck))
+		return PTR_ERR(ocpi_ck);
+
+	clk_use(ocpi_ck);
+	ocpi_enable();
+	printk("OMAP OCPI interconnect driver loaded\n");
+
+	return 0;
+}
+
+static void __exit omap_ocpi_exit(void)
+{
+	/* REVISIT: Disable OCPI */
+
+	if (!cpu_is_omap16xx())
+		return;
+
+	clk_unuse(ocpi_ck);
+	clk_put(ocpi_ck);
+}
+
+MODULE_AUTHOR("Tony Lindgren <tony@atomide.com>");
+MODULE_DESCRIPTION("OMAP OCPI bus controller module");
+MODULE_LICENSE("GPL");
+module_init(omap_ocpi_init);
+module_exit(omap_ocpi_exit);