dt-bindings: remoteproc: qcom: Convert SC7180 MSS bindings to YAML

Add a separate YAML binding to act as a superset of the PAS and non-PAS
compatible for SC7180 MSS PIL. This also serves as a way to increase
readability.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1657020721-24939-3-git-send-email-quic_sibis@quicinc.com

Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt

@@ -14,7 +14,6 @@ on the Qualcomm Hexagon core.
 		    "qcom,msm8974-mss-pil"
 		    "qcom,msm8996-mss-pil"
 		    "qcom,msm8998-mss-pil"
-		    "qcom,sc7180-mss-pil"
 		    "qcom,sdm845-mss-pil"
 
 - reg:
@@ -46,7 +45,6 @@ on the Qualcomm Hexagon core.
 		    must be "wdog", "fatal", "ready", "handover", "stop-ack"
 	qcom,msm8996-mss-pil:
 	qcom,msm8998-mss-pil:
-	qcom,sc7180-mss-pil:
 	qcom,sdm845-mss-pil:
 		    must be "wdog", "fatal", "ready", "handover", "stop-ack",
 		    "shutdown-ack"
@@ -84,9 +82,6 @@ on the Qualcomm Hexagon core.
 	qcom,msm8998-mss-pil:
 		    must be "iface", "bus", "mem", "xo", "gpll0_mss",
 		    "snoc_axi", "mnoc_axi", "qdss"
-	qcom,sc7180-mss-pil:
-		    must be "iface", "bus", "xo", "snoc_axi", "mnoc_axi",
-		    "nav"
 	qcom,sdm845-mss-pil:
 		    must be "iface", "bus", "mem", "xo", "gpll0_mss",
 		    "snoc_axi", "mnoc_axi", "prng"
@@ -98,7 +93,7 @@ on the Qualcomm Hexagon core.
 		    reference to the list of 3 reset-controllers for the
 		    wcss sub-system
 		    reference to the list of 2 reset-controllers for the modem
-		    sub-system on SC7180, SDM845 SoCs
+		    sub-system on SDM845 SoCs
 
 - reset-names:
 	Usage: required
@@ -107,7 +102,7 @@ on the Qualcomm Hexagon core.
 		    must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset"
 		    for the wcss sub-system
 		    must be "mss_restart", "pdc_reset" for the modem
-		    sub-system on SC7180, SDM845 SoCs
+		    sub-system on SDM845 SoCs
 
 For devices where the mba and mpss sub-nodes are not specified, mba/mpss region
 should be referenced as follows:
@@ -172,8 +167,6 @@ For the compatible string below the following supplies are required:
 	qcom,msm8996-mss-pil:
 	qcom,msm8998-mss-pil:
 		    must be "cx", "mx"
-	qcom,sc7180-mss-pil:
-		    must be "cx", "mx", "mss"
 	qcom,sdm845-mss-pil:
 		    must be "cx", "mx", "mss"
 
@@ -200,15 +193,6 @@ For the compatible string below the following supplies are required:
 		    by the three offsets within syscon for q6, modem and nc
 		    halt registers.
 
-For the compatible strings below the following phandle references are required:
-  "qcom,sc7180-mss-pil"
-- qcom,spare-regs:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: a phandle reference to a syscon representing TCSR followed
-		    by the offset within syscon for conn_box_spare0 register
-		    used by the modem sub-system running on SC7180 SoC.
-
 The Hexagon node must contain iommus property as described in ../iommu/iommu.txt
 on platforms which do not have TrustZone.
 

Documentation/devicetree/bindings/remoteproc/qcom,sc7180-mss-pil.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/remoteproc/qcom,sc7180-mss-pil.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SC7180 MSS Peripheral Image Loader
+
+maintainers:
+  - Sibi Sankar <quic_sibis@quicinc.com>
+
+description:
+  This document describes the hardware for a component that loads and boots firmware
+  on the Qualcomm Technology Inc. SC7180 Modem Hexagon Core.
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc7180-mss-pil
+
+  reg:
+    items:
+      - description: MSS QDSP6 registers
+      - description: RMB registers
+
+  reg-names:
+    items:
+      - const: qdsp6
+      - const: rmb
+
+  iommus:
+    items:
+      - description: MSA Stream 1
+      - description: MSA Stream 2
+
+  interrupts:
+    items:
+      - description: Watchdog interrupt
+      - description: Fatal interrupt
+      - description: Ready interrupt
+      - description: Handover interrupt
+      - description: Stop acknowledge interrupt
+      - description: Shutdown acknowledge interrupt
+
+  interrupt-names:
+    items:
+      - const: wdog
+      - const: fatal
+      - const: ready
+      - const: handover
+      - const: stop-ack
+      - const: shutdown-ack
+
+  clocks:
+    items:
+      - description: GCC MSS IFACE clock
+      - description: GCC MSS BUS clock
+      - description: GCC MSS NAV clock
+      - description: GCC MSS SNOC_AXI clock
+      - description: GCC MSS MFAB_AXIS clock
+      - description: RPMH XO clock
+
+  clock-names:
+    items:
+      - const: iface
+      - const: bus
+      - const: nav
+      - const: snoc_axi
+      - const: mnoc_axi
+      - const: xo
+
+  power-domains:
+    items:
+      - description: CX power domain
+      - description: MX power domain
+      - description: MSS power domain
+
+  power-domain-names:
+    items:
+      - const: cx
+      - const: mx
+      - const: mss
+
+  resets:
+    items:
+      - description: AOSS restart
+      - description: PDC reset
+
+  reset-names:
+    items:
+      - const: mss_restart
+      - const: pdc_reset
+
+  memory-region:
+    items:
+      - description: MBA reserved region
+      - description: modem reserved region
+
+  firmware-name:
+    $ref: /schemas/types.yaml#/definitions/string-array
+    items:
+      - description: Name of MBA firmware
+      - description: Name of modem firmware
+
+  qcom,halt-regs:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description:
+      Halt registers are used to halt transactions of various sub-components
+      within MSS.
+    items:
+      - items:
+          - description: phandle to TCSR_MUTEX registers
+          - description: offset to the Q6 halt register
+          - description: offset to the modem halt register
+          - description: offset to the nc halt register
+
+  qcom,spare-regs:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description:
+      Spare registers are multipurpose registers used for errata
+      handling.
+    items:
+      - items:
+          - description: phandle to TCSR_MUTEX registers
+          - description: offset to the conn_box_spare0 register
+
+  qcom,qmp:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: Reference to the AOSS side-channel message RAM.
+
+  qcom,smem-states:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    description: States used by the AP to signal the Hexagon core
+    items:
+      - description: Stop the modem
+
+  qcom,smem-state-names:
+    description: The names of the state bits used for SMP2P output
+    const: stop
+
+  glink-edge:
+    $ref: qcom,glink-edge.yaml#
+    description:
+      Qualcomm G-Link subnode which represents communication edge, channels
+      and devices related to the DSP.
+
+    properties:
+      interrupts:
+        items:
+          - description: IRQ from MSS to GLINK
+
+      mboxes:
+        items:
+          - description: Mailbox for communication between APPS and MSS
+
+      label:
+        const: modem
+
+      apr: false
+      fastrpc: false
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - iommus
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - power-domains
+  - power-domain-names
+  - resets
+  - reset-names
+  - qcom,halt-regs
+  - qcom,spare-regs
+  - memory-region
+  - qcom,qmp
+  - qcom,smem-states
+  - qcom,smem-state-names
+  - glink-edge
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+    #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
+    #include <dt-bindings/reset/qcom,sdm845-aoss.h>
+    #include <dt-bindings/reset/qcom,sdm845-pdc.h>
+
+    remoteproc_mpss: remoteproc@4080000 {
+        compatible = "qcom,sc7180-mss-pil";
+        reg = <0x04080000 0x10000>, <0x04180000 0x48>;
+        reg-names = "qdsp6", "rmb";
+
+        iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
+
+        interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+                              <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+
+        interrupt-names = "wdog", "fatal", "ready", "handover",
+                          "stop-ack", "shutdown-ack";
+
+        clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+                 <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
+                 <&gcc GCC_MSS_NAV_AXI_CLK>,
+                 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+                 <&gcc GCC_MSS_MFAB_AXIS_CLK>,
+                 <&rpmhcc RPMH_CXO_CLK>;
+        clock-names = "iface", "bus", "nav", "snoc_axi",
+                      "mnoc_axi", "xo";
+
+        power-domains = <&rpmhpd SC7180_CX>,
+                        <&rpmhpd SC7180_MX>,
+                        <&rpmhpd SC7180_MSS>;
+        power-domain-names = "cx", "mx", "mss";
+
+        memory-region = <&mba_mem>, <&mpss_mem>;
+
+        qcom,qmp = <&aoss_qmp>;
+
+        qcom,smem-states = <&modem_smp2p_out 0>;
+        qcom,smem-state-names = "stop";
+
+        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
+        reset-names = "mss_restart", "pdc_reset";
+
+        qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
+        qcom,spare-regs = <&tcsr_regs 0xb3e4>;
+
+        glink-edge {
+            interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
+            mboxes = <&apss_shared 12>;
+            qcom,remote-pid = <1>;
+            label = "modem";
+        };
+    };