Commit 5ebaaa69 authored by David S. Miller's avatar David S. Miller

Merge branch 'sja1105-phylink-updates'

Russell King says:

====================
net: dsa: sja1105: phylink updates

This series updates the phylink implementation in sja1105 to use the
supported_interfaces bitmap, convert to the mac_select_pcs() interface,
mark as non-legacy, and get rid of the validation method.

As a final step, enable switching between SGMII and 2500BASE-X as it
is a feature that Vladimir desires.

Specifically, the patches in this series:

1. Populates the supported_interfaces bitmap.
2. As a result of the supported_interfaces bitmap being populated,
   sja1105 no longer needs to check the interface mode as phylink
   will do this.
3. Switch away from using phylink_set_pcs(), using the mac_select_pcs()
   method instead.
4. Mark the driver as not-legacy
5. Fill in mac_capabilities using _exactly_ the same conditions as is
   currently used to decide which link modes to support, and convert
   to use phylink_generic_validate()
6. Add brand new support to permit switching between SGMII and
   2500BASE-X modes of operation as per Vladimir's single patch that
   performs steps 1, 2, 5 and 6 in one go.

There are some additional changes in Vladimir's single patch that I
have not included:

* validation of priv->phy_mode[] in sja1105_phylink_get_caps(). The
  driver has already validated the phy_mode for each port in
  sja1105_init_mii_settings(), and a failure here will prevent the
  driver reaching sja1105_phylink_get_caps().

* Changing the decisions on which mac_capabilities to set. Vladimir's
  patch always sets MAC_10FD | MAC_100FD | MAC_1000FD despite the
  current code clearly making the 1G speed conditional on the
  xmii_mode for the port. The change in decision making may be
  visible when in PHY_INTERFACE_MODE_INTERNAL mode, for which
  the phylink_generic_validate() will pass through all the MAC
  capabilities as ethtool link modes.

  Hence, if we have PHY_INTERFACE_MODE_INTERNAL but supports_rgmii[]
  or supports_sgmii[] is non-zero, currently we do not get 1G speeds.
  With Vladimir's additional change, we will get 1G speeds.

  While it is not clear whether that can happen, I feel changing the
  decision making should be a separate patch.

* The decision for MAC_2500FD is made differently -
  sja1105_init_mii_settings() allows PHY_INTERFACE_MODE_2500BASEX
  when supports_2500basex[] is non-zero, and is not based on any other
  condition such as supports_sgmii[] or supports_rgmii[]. Vladimir's
  patch makes it additionally conditional on those supports_.gmii[]
  settings, which is a functional change that should be made in a
  separate patch - and if desired, then sja1105_init_mii_settings()
  should also be updated at the same time.

Consequently, I believe that my previous objections to Vladimir's
single patch approach are well founded and justified, even through
Vladimir is the maintainer of this driver. I have no objection to
the additional changes, I just don't think they should all be wrapped
up into a single patch that converts the way validation is done _and_
also makes a bunch of other functional changes.

RFC->non-RFC: added Vladimir's Reviewed-by's, fixed the typo in the
commit message of patch 6, and removed the phrase at the end of a
comment as requested.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents 28a3f060 83dc4c2a
......@@ -1358,37 +1358,16 @@ static int sja1105_adjust_port_config(struct sja1105_private *priv, int port,
return sja1105_clocking_setup_port(priv, port);
}
/* The SJA1105 MAC programming model is through the static config (the xMII
* Mode table cannot be dynamically reconfigured), and we have to program
* that early (earlier than PHYLINK calls us, anyway).
* So just error out in case the connected PHY attempts to change the initial
* system interface MII protocol from what is defined in the DT, at least for
* now.
*/
static bool sja1105_phy_mode_mismatch(struct sja1105_private *priv, int port,
phy_interface_t interface)
{
return priv->phy_mode[port] != interface;
}
static void sja1105_mac_config(struct dsa_switch *ds, int port,
unsigned int mode,
const struct phylink_link_state *state)
static struct phylink_pcs *
sja1105_mac_select_pcs(struct dsa_switch *ds, int port, phy_interface_t iface)
{
struct dsa_port *dp = dsa_to_port(ds, port);
struct sja1105_private *priv = ds->priv;
struct dw_xpcs *xpcs;
if (sja1105_phy_mode_mismatch(priv, port, state->interface)) {
dev_err(ds->dev, "Changing PHY mode to %s not supported!\n",
phy_modes(state->interface));
return;
}
xpcs = priv->xpcs[port];
struct dw_xpcs *xpcs = priv->xpcs[port];
if (xpcs)
phylink_set_pcs(dp->pl, &xpcs->pcs);
return &xpcs->pcs;
return NULL;
}
static void sja1105_mac_link_down(struct dsa_switch *ds, int port,
......@@ -1412,48 +1391,53 @@ static void sja1105_mac_link_up(struct dsa_switch *ds, int port,
sja1105_inhibit_tx(priv, BIT(port), false);
}
static void sja1105_phylink_validate(struct dsa_switch *ds, int port,
unsigned long *supported,
struct phylink_link_state *state)
static void sja1105_phylink_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
{
/* Construct a new mask which exhaustively contains all link features
* supported by the MAC, and then apply that (logical AND) to what will
* be sent to the PHY for "marketing".
*/
__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
struct sja1105_private *priv = ds->priv;
struct sja1105_xmii_params_entry *mii;
phy_interface_t phy_mode;
mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries;
/* include/linux/phylink.h says:
* When @state->interface is %PHY_INTERFACE_MODE_NA, phylink
* expects the MAC driver to return all supported link modes.
/* This driver does not make use of the speed, duplex, pause or the
* advertisement in its mac_config, so it is safe to mark this driver
* as non-legacy.
*/
if (state->interface != PHY_INTERFACE_MODE_NA &&
sja1105_phy_mode_mismatch(priv, port, state->interface)) {
linkmode_zero(supported);
return;
config->legacy_pre_march2020 = false;
phy_mode = priv->phy_mode[port];
if (phy_mode == PHY_INTERFACE_MODE_SGMII ||
phy_mode == PHY_INTERFACE_MODE_2500BASEX) {
/* Changing the PHY mode on SERDES ports is possible and makes
* sense, because that is done through the XPCS. We allow
* changes between SGMII and 2500base-X.
*/
if (priv->info->supports_sgmii[port])
__set_bit(PHY_INTERFACE_MODE_SGMII,
config->supported_interfaces);
if (priv->info->supports_2500basex[port])
__set_bit(PHY_INTERFACE_MODE_2500BASEX,
config->supported_interfaces);
} else {
/* The SJA1105 MAC programming model is through the static
* config (the xMII Mode table cannot be dynamically
* reconfigured), and we have to program that early.
*/
__set_bit(phy_mode, config->supported_interfaces);
}
/* The MAC does not support pause frames, and also doesn't
* support half-duplex traffic modes.
*/
phylink_set(mask, Autoneg);
phylink_set(mask, MII);
phylink_set(mask, 10baseT_Full);
phylink_set(mask, 100baseT_Full);
phylink_set(mask, 100baseT1_Full);
config->mac_capabilities = MAC_10FD | MAC_100FD;
mii = priv->static_config.tables[BLK_IDX_XMII_PARAMS].entries;
if (mii->xmii_mode[port] == XMII_MODE_RGMII ||
mii->xmii_mode[port] == XMII_MODE_SGMII)
phylink_set(mask, 1000baseT_Full);
if (priv->info->supports_2500basex[port]) {
phylink_set(mask, 2500baseT_Full);
phylink_set(mask, 2500baseX_Full);
}
config->mac_capabilities |= MAC_1000FD;
linkmode_and(supported, supported, mask);
linkmode_and(state->advertising, state->advertising, mask);
if (priv->info->supports_2500basex[port])
config->mac_capabilities |= MAC_2500FD;
}
static int
......@@ -3152,8 +3136,8 @@ static const struct dsa_switch_ops sja1105_switch_ops = {
.set_ageing_time = sja1105_set_ageing_time,
.port_change_mtu = sja1105_change_mtu,
.port_max_mtu = sja1105_get_max_mtu,
.phylink_validate = sja1105_phylink_validate,
.phylink_mac_config = sja1105_mac_config,
.phylink_get_caps = sja1105_phylink_get_caps,
.phylink_mac_select_pcs = sja1105_mac_select_pcs,
.phylink_mac_link_up = sja1105_mac_link_up,
.phylink_mac_link_down = sja1105_mac_link_down,
.get_strings = sja1105_get_strings,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment