Commit 604536dc authored by Marek Vasut's avatar Marek Vasut Committed by Alexandre Torgue

ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2

The DH Electronics PDK2 can be populated with SoM with any STM32MP15xx
variant. Split the SoC-independent parts of the SoM and PDK2 into the
stm32mp15xx-dhcom-*.dtsi and reduce stm32mp157c-dhcom-*dts* to example
of adding STM32MP157C variant of the SoM into a PDK2 carrier board.
Signed-off-by: default avatarMarek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: default avatarAlexandre Torgue <alexandre.torgue@st.com>
parent 81d5fc71
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
* Copyright (C) 2019 Marek Vasut <marex@denx.de>
* Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
*
* DHCOM STM32MP1 variant:
* DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2
* DHCOR PCB number: 587-200 or newer
* PDK2 PCB number: 516-400 or newer
*/
/dts-v1/;
#include "stm32mp157c-dhcom-som.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/pwm/pwm.h>
#include "stm32mp157.dtsi"
#include "stm32mp15xc.dtsi"
#include "stm32mp15xx-dhcom-som.dtsi"
#include "stm32mp15xx-dhcom-pdk2.dtsi"
/ {
model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)";
compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
aliases {
serial0 = &uart4;
serial1 = &usart3;
serial2 = &uart8;
ethernet0 = &ethernet0;
};
chosen {
stdout-path = "serial0:115200n8";
};
clk_ext_audio_codec: clock-codec {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
};
display_bl: display-bl {
compatible = "pwm-backlight";
pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
default-brightness-level = <8>;
enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
status = "okay";
};
ethernet_vio: vioregulator {
compatible = "regulator-fixed";
regulator-name = "vio";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
regulator-always-on;
regulator-boot-on;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#size-cells = <0>;
poll-interval = <20>;
/*
* The EXTi IRQ line 3 is shared with touchscreen and ethernet,
* so mark this as polled GPIO key.
*/
button-0 {
label = "TA1-GPIO-A";
linux,code = <KEY_A>;
gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
};
};
gpio-keys {
compatible = "gpio-keys";
#size-cells = <0>;
button-1 {
label = "TA2-GPIO-B";
linux,code = <KEY_B>;
gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
wakeup-source;
};
button-2 {
label = "TA3-GPIO-C";
linux,code = <KEY_C>;
gpios = <&gpioi 11 GPIO_ACTIVE_LOW>;
wakeup-source;
};
button-3 {
label = "TA4-GPIO-D";
linux,code = <KEY_D>;
gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
wakeup-source;
};
};
led {
compatible = "gpio-leds";
led-0 {
label = "green:led5";
gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led-1 {
label = "green:led6";
gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led-2 {
label = "green:led7";
gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led-3 {
label = "green:led8";
gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
panel {
compatible = "edt,etm0700g0edh6";
backlight = <&display_bl>;
port {
lcd_panel_in: endpoint {
remote-endpoint = <&lcd_display_out>;
};
};
};
sound {
compatible = "audio-graph-card";
routing =
"MIC_IN", "Capture",
"Capture", "Mic Bias",
"Playback", "HP_OUT";
dais = <&sai2a_port &sai2b_port>;
status = "okay";
};
};
&cec {
pinctrl-names = "default";
pinctrl-0 = <&cec_pins_a>;
status = "okay";
};
&ethernet0 {
status = "okay";
pinctrl-0 = <&ethernet0_rmii_pins_a>;
pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
pinctrl-names = "default", "sleep";
phy-mode = "rmii";
max-speed = <100>;
phy-handle = <&phy0>;
st,eth-ref-clk-sel;
phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy0: ethernet-phy@1 {
reg = <1>;
};
};
};
&i2c2 { /* Header X22 */
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
};
&i2c5 { /* Header X21 */
pinctrl-names = "default";
pinctrl-0 = <&i2c5_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
sgtl5000: codec@a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
#sound-dai-cells = <0>;
clocks = <&clk_ext_audio_codec>;
VDDA-supply = <&v3v3>;
VDDIO-supply = <&vdd>;
sgtl5000_port: port {
#address-cells = <1>;
#size-cells = <0>;
sgtl5000_tx_endpoint: endpoint@0 {
reg = <0>;
remote-endpoint = <&sai2a_endpoint>;
frame-master;
bitclock-master;
};
sgtl5000_rx_endpoint: endpoint@1 {
reg = <1>;
remote-endpoint = <&sai2b_endpoint>;
frame-master;
bitclock-master;
};
};
};
polytouch@38 {
compatible = "edt,edt-ft5x06";
reg = <0x38>;
interrupt-parent = <&gpiog>;
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
linux,wakeup;
};
};
&ltdc {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&ltdc_pins_b>;
pinctrl-1 = <&ltdc_sleep_pins_b>;
status = "okay";
port {
lcd_display_out: endpoint {
remote-endpoint = <&lcd_panel_in>;
};
};
model = "DH Electronics STM32MP157C DHCOM Premium Developer Kit (2)";
compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som",
"st,stm32mp157";
};
&m_can1 {
......@@ -246,103 +26,3 @@ &m_can1 {
pinctrl-1 = <&m_can1_sleep_pins_a>;
status = "okay";
};
&sai2 {
clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
clock-names = "pclk", "x8k", "x11k";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
status = "okay";
sai2a: audio-controller@4400b004 {
#clock-cells = <0>;
dma-names = "tx";
clocks = <&rcc SAI2_K>;
clock-names = "sai_ck";
status = "okay";
sai2a_port: port {
sai2a_endpoint: endpoint {
remote-endpoint = <&sgtl5000_tx_endpoint>;
format = "i2s";
mclk-fs = <512>;
dai-tdm-slot-num = <2>;
dai-tdm-slot-width = <16>;
};
};
};
sai2b: audio-controller@4400b024 {
dma-names = "rx";
st,sync = <&sai2a 2>;
clocks = <&rcc SAI2_K>, <&sai2a>;
clock-names = "sai_ck", "MCLK";
status = "okay";
sai2b_port: port {
sai2b_endpoint: endpoint {
remote-endpoint = <&sgtl5000_rx_endpoint>;
format = "i2s";
mclk-fs = <512>;
dai-tdm-slot-num = <2>;
dai-tdm-slot-width = <16>;
};
};
};
};
&timers2 {
/* spare dmas for other usage (un-delete to enable pwm capture) */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
pwm2: pwm {
pinctrl-0 = <&pwm2_pins_a>;
pinctrl-names = "default";
status = "okay";
};
timer@1 {
status = "okay";
};
};
&usart3 {
pinctrl-names = "default";
pinctrl-0 = <&usart3_pins_a>;
status = "okay";
};
&uart8 {
pinctrl-names = "default";
pinctrl-0 = <&uart8_pins_a>;
status = "okay";
};
&usbh_ehci {
phys = <&usbphyc_port0>;
status = "okay";
};
&usbotg_hs {
dr_mode = "peripheral";
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";
};
&usbphyc {
status = "okay";
};
&usbphyc_port0 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
};
&usbphyc_port1 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
};
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
* Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
*/
#include <dt-bindings/input/input.h>
#include <dt-bindings/pwm/pwm.h>
/ {
aliases {
serial0 = &uart4;
serial1 = &usart3;
serial2 = &uart8;
ethernet0 = &ethernet0;
};
chosen {
stdout-path = "serial0:115200n8";
};
clk_ext_audio_codec: clock-codec {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <24000000>;
};
display_bl: display-bl {
compatible = "pwm-backlight";
pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
default-brightness-level = <8>;
enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
status = "okay";
};
ethernet_vio: vioregulator {
compatible = "regulator-fixed";
regulator-name = "vio";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
regulator-always-on;
regulator-boot-on;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#size-cells = <0>;
poll-interval = <20>;
/*
* The EXTi IRQ line 3 is shared with touchscreen and ethernet,
* so mark this as polled GPIO key.
*/
button-0 {
label = "TA1-GPIO-A";
linux,code = <KEY_A>;
gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
};
};
gpio-keys {
compatible = "gpio-keys";
#size-cells = <0>;
button-1 {
label = "TA2-GPIO-B";
linux,code = <KEY_B>;
gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
wakeup-source;
};
button-2 {
label = "TA3-GPIO-C";
linux,code = <KEY_C>;
gpios = <&gpioi 11 GPIO_ACTIVE_LOW>;
wakeup-source;
};
button-3 {
label = "TA4-GPIO-D";
linux,code = <KEY_D>;
gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
wakeup-source;
};
};
led {
compatible = "gpio-leds";
led-0 {
label = "green:led5";
gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led-1 {
label = "green:led6";
gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led-2 {
label = "green:led7";
gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
led-3 {
label = "green:led8";
gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
panel {
compatible = "edt,etm0700g0edh6";
backlight = <&display_bl>;
port {
lcd_panel_in: endpoint {
remote-endpoint = <&lcd_display_out>;
};
};
};
sound {
compatible = "audio-graph-card";
routing =
"MIC_IN", "Capture",
"Capture", "Mic Bias",
"Playback", "HP_OUT";
dais = <&sai2a_port &sai2b_port>;
status = "okay";
};
};
&cec {
pinctrl-names = "default";
pinctrl-0 = <&cec_pins_a>;
status = "okay";
};
&ethernet0 {
status = "okay";
pinctrl-0 = <&ethernet0_rmii_pins_a>;
pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
pinctrl-names = "default", "sleep";
phy-mode = "rmii";
max-speed = <100>;
phy-handle = <&phy0>;
st,eth-ref-clk-sel;
phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy0: ethernet-phy@1 {
reg = <1>;
};
};
};
&i2c2 { /* Header X22 */
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
};
&i2c5 { /* Header X21 */
pinctrl-names = "default";
pinctrl-0 = <&i2c5_pins_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
/delete-property/dma-names;
sgtl5000: codec@a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
#sound-dai-cells = <0>;
clocks = <&clk_ext_audio_codec>;
VDDA-supply = <&v3v3>;
VDDIO-supply = <&vdd>;
sgtl5000_port: port {
#address-cells = <1>;
#size-cells = <0>;
sgtl5000_tx_endpoint: endpoint@0 {
reg = <0>;
remote-endpoint = <&sai2a_endpoint>;
frame-master;
bitclock-master;
};
sgtl5000_rx_endpoint: endpoint@1 {
reg = <1>;
remote-endpoint = <&sai2b_endpoint>;
frame-master;
bitclock-master;
};
};
};
polytouch@38 {
compatible = "edt,edt-ft5x06";
reg = <0x38>;
interrupt-parent = <&gpiog>;
interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
linux,wakeup;
};
};
&ltdc {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&ltdc_pins_b>;
pinctrl-1 = <&ltdc_sleep_pins_b>;
status = "okay";
port {
lcd_display_out: endpoint {
remote-endpoint = <&lcd_panel_in>;
};
};
};
&sai2 {
clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
clock-names = "pclk", "x8k", "x11k";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
status = "okay";
sai2a: audio-controller@4400b004 {
#clock-cells = <0>;
dma-names = "tx";
clocks = <&rcc SAI2_K>;
clock-names = "sai_ck";
status = "okay";
sai2a_port: port {
sai2a_endpoint: endpoint {
remote-endpoint = <&sgtl5000_tx_endpoint>;
format = "i2s";
mclk-fs = <512>;
dai-tdm-slot-num = <2>;
dai-tdm-slot-width = <16>;
};
};
};
sai2b: audio-controller@4400b024 {
dma-names = "rx";
st,sync = <&sai2a 2>;
clocks = <&rcc SAI2_K>, <&sai2a>;
clock-names = "sai_ck", "MCLK";
status = "okay";
sai2b_port: port {
sai2b_endpoint: endpoint {
remote-endpoint = <&sgtl5000_rx_endpoint>;
format = "i2s";
mclk-fs = <512>;
dai-tdm-slot-num = <2>;
dai-tdm-slot-width = <16>;
};
};
};
};
&timers2 {
/* spare dmas for other usage (un-delete to enable pwm capture) */
/delete-property/dmas;
/delete-property/dma-names;
status = "okay";
pwm2: pwm {
pinctrl-0 = <&pwm2_pins_a>;
pinctrl-names = "default";
status = "okay";
};
timer@1 {
status = "okay";
};
};
&usart3 {
pinctrl-names = "default";
pinctrl-0 = <&usart3_pins_a>;
status = "okay";
};
&uart8 {
pinctrl-names = "default";
pinctrl-0 = <&uart8_pins_a>;
status = "okay";
};
&usbh_ehci {
phys = <&usbphyc_port0>;
status = "okay";
};
&usbotg_hs {
dr_mode = "peripheral";
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";
};
&usbphyc {
status = "okay";
};
&usbphyc_port0 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
};
&usbphyc_port1 {
phy-supply = <&vdd_usb>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
};
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) 2019 Marek Vasut <marex@denx.de>
* Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
*/
/dts-v1/;
#include "stm32mp157.dtsi"
#include "stm32mp15xc.dtsi"
#include "stm32mp15-pinctrl.dtsi"
#include "stm32mp15xxaa-pinctrl.dtsi"
#include <dt-bindings/gpio/gpio.h>
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment