ARM: dts: bcm283x: Enable HDMI at board level

There might be headless setups of the Compute Module without HDMI,
so better enable HDMI at board level. Btw this allows moving HDMI
base definition into upcoming bcm2835-common.dtsi.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Eric Anholt <eric@anholt.net>

arch/arm/boot/dts/bcm2835-rpi-a-plus.dts

@@ -104,6 +104,8 @@ i2s_alt0: i2s_alt0 {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2835-rpi-a.dts

@@ -99,6 +99,8 @@ i2s_alt2: i2s_alt2 {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -106,6 +106,8 @@ i2s_alt0: i2s_alt0 {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts

@@ -99,6 +99,8 @@ i2s_alt2: i2s_alt2 {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -94,6 +94,8 @@ &gpio {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts

@@ -79,6 +79,8 @@ &gpio {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &sdhost {

arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

@@ -105,6 +105,8 @@ &gpio {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &sdhci {

arch/arm/boot/dts/bcm2835-rpi-zero.dts

@@ -101,6 +101,8 @@ i2s_alt0: i2s_alt0 {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &sdhost {

arch/arm/boot/dts/bcm2835-rpi.dtsi

@@ -67,11 +67,6 @@ &usb {
 	power-domains = <&power RPI_POWER_DOMAIN_USB>;
 };
 
-&hdmi {
-	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
-	status = "okay";
-};
-
 &vec {
 	power-domains = <&power RPI_POWER_DOMAIN_VEC>;
 	status = "okay";

arch/arm/boot/dts/bcm2836-rpi-2-b.dts

@@ -106,6 +106,8 @@ i2s_alt0: i2s_alt0 {
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts

@@ -118,6 +118,8 @@ &gpio {
 
 &hdmi {
 	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts

@@ -125,6 +125,8 @@ &gpio {
 
 &hdmi {
 	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &pwm {

arch/arm/boot/dts/bcm2837-rpi-3-b.dts

@@ -126,6 +126,8 @@ &pwm {
 
 &hdmi {
 	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 /* uart0 communicates with the BT module */

arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts

@@ -78,6 +78,8 @@ &gpio {
 
 &hdmi {
 	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
 };
 
 &sdhost {