Commit 63970c29 authored by 周琰杰 (Zhou Yanjie)'s avatar 周琰杰 (Zhou Yanjie) Committed by Thomas Bogendoerfer

MIPS: Ingenic: Add Ingenic X1830 support.

Support the Ingenic X1830 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1830 based board is
added in a later commit.
Tested-by: default avatar周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: default avatar周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: default avatarThomas Bogendoerfer <tsbogend@alpha.franken.de>
parent c7c101df
// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/clock/ingenic,tcu.h>
#include <dt-bindings/clock/x1830-cgu.h>
#include <dt-bindings/dma/x1830-dma.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
compatible = "ingenic,x1830";
cpuintc: interrupt-controller {
#address-cells = <0>;
#interrupt-cells = <1>;
interrupt-controller;
compatible = "mti,cpu-interrupt-controller";
};
intc: interrupt-controller@10001000 {
compatible = "ingenic,x1830-intc", "ingenic,jz4780-intc";
reg = <0x10001000 0x50>;
interrupt-controller;
#interrupt-cells = <1>;
interrupt-parent = <&cpuintc>;
interrupts = <2>;
};
exclk: ext {
compatible = "fixed-clock";
#clock-cells = <0>;
};
rtclk: rtc {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
};
cgu: x1830-cgu@10000000 {
compatible = "ingenic,x1830-cgu";
reg = <0x10000000 0x100>;
#clock-cells = <1>;
clocks = <&exclk>, <&rtclk>;
clock-names = "ext", "rtc";
};
tcu: timer@10002000 {
compatible = "ingenic,x1830-tcu", "ingenic,x1000-tcu", "simple-mfd";
reg = <0x10002000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x10002000 0x1000>;
#clock-cells = <1>;
clocks = <&cgu X1830_CLK_RTCLK
&cgu X1830_CLK_EXCLK
&cgu X1830_CLK_PCLK>;
clock-names = "rtc", "ext", "pclk";
interrupt-controller;
#interrupt-cells = <1>;
interrupt-parent = <&intc>;
interrupts = <27 26 25>;
wdt: watchdog@0 {
compatible = "ingenic,x1830-watchdog", "ingenic,jz4780-watchdog";
reg = <0x0 0x10>;
clocks = <&tcu TCU_CLK_WDT>;
clock-names = "wdt";
};
};
rtc: rtc@10003000 {
compatible = "ingenic,x1830-rtc", "ingenic,jz4780-rtc";
reg = <0x10003000 0x4c>;
interrupt-parent = <&intc>;
interrupts = <32>;
clocks = <&cgu X1830_CLK_RTCLK>;
clock-names = "rtc";
};
pinctrl: pin-controller@10010000 {
compatible = "ingenic,x1830-pinctrl";
reg = <0x10010000 0x800>;
#address-cells = <1>;
#size-cells = <0>;
gpa: gpio@0 {
compatible = "ingenic,x1830-gpio";
reg = <0>;
gpio-controller;
gpio-ranges = <&pinctrl 0 0 32>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&intc>;
interrupts = <17>;
};
gpb: gpio@1 {
compatible = "ingenic,x1830-gpio";
reg = <1>;
gpio-controller;
gpio-ranges = <&pinctrl 0 32 32>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&intc>;
interrupts = <16>;
};
gpc: gpio@2 {
compatible = "ingenic,x1830-gpio";
reg = <2>;
gpio-controller;
gpio-ranges = <&pinctrl 0 64 32>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&intc>;
interrupts = <15>;
};
gpd: gpio@3 {
compatible = "ingenic,x1830-gpio";
reg = <3>;
gpio-controller;
gpio-ranges = <&pinctrl 0 96 32>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&intc>;
interrupts = <14>;
};
};
uart0: serial@10030000 {
compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
reg = <0x10030000 0x100>;
interrupt-parent = <&intc>;
interrupts = <51>;
clocks = <&exclk>, <&cgu X1830_CLK_UART0>;
clock-names = "baud", "module";
status = "disabled";
};
uart1: serial@10031000 {
compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
reg = <0x10031000 0x100>;
interrupt-parent = <&intc>;
interrupts = <50>;
clocks = <&exclk>, <&cgu X1830_CLK_UART1>;
clock-names = "baud", "module";
status = "disabled";
};
i2c0: i2c-controller@10050000 {
compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
reg = <0x10050000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&intc>;
interrupts = <60>;
clocks = <&cgu X1830_CLK_SMB0>;
status = "disabled";
};
i2c1: i2c-controller@10051000 {
compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
reg = <0x10051000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&intc>;
interrupts = <59>;
clocks = <&cgu X1830_CLK_SMB1>;
status = "disabled";
};
i2c2: i2c-controller@10052000 {
compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
reg = <0x10052000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&intc>;
interrupts = <58>;
clocks = <&cgu X1830_CLK_SMB2>;
status = "disabled";
};
pdma: dma-controller@13420000 {
compatible = "ingenic,x1830-dma";
reg = <0x13420000 0x400
0x13421000 0x40>;
#dma-cells = <2>;
interrupt-parent = <&intc>;
interrupts = <10>;
clocks = <&cgu X1830_CLK_PDMA>;
};
msc0: mmc@13450000 {
compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
reg = <0x13450000 0x1000>;
interrupt-parent = <&intc>;
interrupts = <37>;
clocks = <&cgu X1830_CLK_MSC0>;
clock-names = "mmc";
cap-sd-highspeed;
cap-mmc-highspeed;
cap-sdio-irq;
dmas = <&pdma X1830_DMA_MSC0_RX 0xffffffff>,
<&pdma X1830_DMA_MSC0_TX 0xffffffff>;
dma-names = "rx", "tx";
status = "disabled";
};
msc1: mmc@13460000 {
compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
reg = <0x13460000 0x1000>;
interrupt-parent = <&intc>;
interrupts = <36>;
clocks = <&cgu X1830_CLK_MSC1>;
clock-names = "mmc";
cap-sd-highspeed;
cap-mmc-highspeed;
cap-sdio-irq;
dmas = <&pdma X1830_DMA_MSC1_RX 0xffffffff>,
<&pdma X1830_DMA_MSC1_TX 0xffffffff>;
dma-names = "rx", "tx";
status = "disabled";
};
mac: ethernet@134b0000 {
compatible = "ingenic,x1830-mac", "snps,dwmac";
reg = <0x134b0000 0x2000>;
interrupt-parent = <&intc>;
interrupts = <55>;
interrupt-names = "macirq";
clocks = <&cgu X1830_CLK_MAC>;
clock-names = "stmmaceth";
status = "disabled";
mdio: mdio {
compatible = "snps,dwmac-mdio";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
};
......@@ -58,3 +58,9 @@ config MACH_X1000
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
config MACH_X1830
bool
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment