arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: Add navigation mezzanine dts

Move the dts data for the rb3 navigation mezzanine into its own dts file.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-6-bryan.odonoghue@linaro.org

arch/arm64/boot/dts/qcom/Makefile

@@ -135,6 +135,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c-navigation-mezzanine.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyln.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb

arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dts

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "sdm845-db845c.dts"
+
+&camss {
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
+
+	status = "okay";
+
+	ports {
+		port@0 {
+			csiphy0_ep: endpoint {
+				data-lanes = <0 1 2 3>;
+				remote-endpoint = <&ov8856_ep>;
+			};
+		};
+	};
+};
+
+&cci {
+	status = "okay";
+};
+
+&cci_i2c0 {
+	camera@10 {
+		compatible = "ovti,ov8856";
+		reg = <0x10>;
+
+		/* CAM0_RST_N */
+		reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cam0_default>;
+
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "xvclk";
+		clock-frequency = <19200000>;
+
+		/*
+		 * The &vreg_s4a_1p8 trace is powered on as a,
+		 * so it is represented by a fixed regulator.
+		 *
+		 * The 2.8V vdda-supply and 1.2V vddd-supply regulators
+		 * both have to be enabled through the power management
+		 * gpios.
+		 */
+		dovdd-supply = <&vreg_lvs1a_1p8>;
+		avdd-supply = <&cam0_avdd_2v8>;
+		dvdd-supply = <&cam0_dvdd_1v2>;
+
+		port {
+			ov8856_ep: endpoint {
+				link-frequencies = /bits/ 64
+					<360000000 180000000>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&csiphy0_ep>;
+			};
+		};
+	};
+};
+
+&cci_i2c1 {
+	camera@60 {
+		compatible = "ovti,ov7251";
+
+		/* I2C address as per ov7251.txt linux documentation */
+		reg = <0x60>;
+
+		/* CAM3_RST_N */
+		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cam3_default>;
+
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "xclk";
+		clock-frequency = <24000000>;
+
+		/*
+		 * The &vreg_s4a_1p8 trace always powered on.
+		 *
+		 * The 2.8V vdda-supply regulator is enabled when the
+		 * vreg_s4a_1p8 trace is pulled high.
+		 * It too is represented by a fixed regulator.
+		 *
+		 * No 1.2V vddd-supply regulator is used.
+		 */
+		vdddo-supply = <&vreg_lvs1a_1p8>;
+		vdda-supply = <&cam3_avdd_2v8>;
+
+		status = "disabled";
+
+		port {
+			ov7251_ep: endpoint {
+				data-lanes = <0 1>;
+/*				remote-endpoint = <&csiphy3_ep>; */
+			};
+		};
+	};
+};

arch/arm64/boot/dts/qcom/sdm845-db845c.dts

@@ -1174,102 +1174,6 @@ &pm8998_gpio {
 
 };
 
-&cci {
-	status = "okay";
-};
-
-&camss {
-	vdda-phy-supply = <&vreg_l1a_0p875>;
-	vdda-pll-supply = <&vreg_l26a_1p2>;
-
-	status = "okay";
-
-	ports {
-		port@0 {
-			csiphy0_ep: endpoint {
-				data-lanes = <0 1 2 3>;
-				remote-endpoint = <&ov8856_ep>;
-			};
-		};
-	};
-};
-
-&cci_i2c0 {
-	camera@10 {
-		compatible = "ovti,ov8856";
-		reg = <0x10>;
-
-		/* CAM0_RST_N */
-		reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&cam0_default>;
-
-		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
-		clock-names = "xvclk";
-		clock-frequency = <19200000>;
-
-		/*
-		 * The &vreg_s4a_1p8 trace is powered on as a,
-		 * so it is represented by a fixed regulator.
-		 *
-		 * The 2.8V vdda-supply and 1.2V vddd-supply regulators
-		 * both have to be enabled through the power management
-		 * gpios.
-		 */
-		dovdd-supply = <&vreg_lvs1a_1p8>;
-		avdd-supply = <&cam0_avdd_2v8>;
-		dvdd-supply = <&cam0_dvdd_1v2>;
-
-		port {
-			ov8856_ep: endpoint {
-				link-frequencies = /bits/ 64
-					<360000000 180000000>;
-				data-lanes = <1 2 3 4>;
-				remote-endpoint = <&csiphy0_ep>;
-			};
-		};
-	};
-};
-
-&cci_i2c1 {
-	camera@60 {
-		compatible = "ovti,ov7251";
-
-		/* I2C address as per ov7251.txt linux documentation */
-		reg = <0x60>;
-
-		/* CAM3_RST_N */
-		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&cam3_default>;
-
-		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
-		clock-names = "xclk";
-		clock-frequency = <24000000>;
-
-		/*
-		 * The &vreg_s4a_1p8 trace always powered on.
-		 *
-		 * The 2.8V vdda-supply regulator is enabled when the
-		 * vreg_s4a_1p8 trace is pulled high.
-		 * It too is represented by a fixed regulator.
-		 *
-		 * No 1.2V vddd-supply regulator is used.
-		 */
-		vdddo-supply = <&vreg_lvs1a_1p8>;
-		vdda-supply = <&cam3_avdd_2v8>;
-
-		status = "disabled";
-
-		port {
-			ov7251_ep: endpoint {
-				data-lanes = <0 1>;
-/*				remote-endpoint = <&csiphy3_ep>; */
-			};
-		};
-	};
-};
-
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 &qup_spi0_default {
 	config {