Merge tag 'arm-soc-fixes-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a fairly large set of bug fixes on top of -rc1, as most of
  them were ready but didn't quite make it into the last-minute pull
  requests for the merge window.

  Allwinner:
   - fix for incorrect CPU overtemperature limit

  Amlogic:
   - multiple smaller DT bugfixes, and missing device nodes

  Marvell EBU:
   - add missing aliases for ethernet switch ports on espressobin board

  Marvell MMP:
   - DTC warning fix
   - bugfix for camera interface power-down

  NXP i.MX:
   - re-enable the GPIO driver on all defconfigs

  ST STM32MP1:
   - fix random crashes from incorrect voltage settings

  Synaptics Berlin:
   - enable the correct hardware timer driver

  Texas Instruments K2G:
   - fix a boot regression in the power domain code

  TEE drivers:
   - fix regression in TEE "login" method

  SCMI drivers:
   - multiple code fixes for corner cases in newly added code

  MAINTAINERS file:
   - move Kukjin Kim and Sangbeom Kim to credits (used to work on
     Samsung Exynos)
   - Masahiro Yamada is stepping down as Uniphier maintainer

  I did not include a series of patches that work around a regression
  caused by a bugfix in an ethernet phy driver that resulted in an
  inadvertent DT binding change. This is still under discussion"

* tag 'arm-soc-fixes-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  soc: ti: ti_sci_pm_domains: check for proper args count in xlate
  ARM: dts: stm32: Describe Vin power supply on stm32mp157c-edx board
  ARM: dts: stm32: Describe Vin power supply on stm32mp15xx-dkx board
  ARM: multi_v5_defconfig: Select CONFIG_GPIO_MXC
  ARM: imx_v4_v5_defconfig: Select CONFIG_GPIO_MXC
  ARM: dts: mmp2-olpc-xo-1-75: Use plural form of "-gpios"
  ARM: dts: mmp3: Add power domain for the camera
  arm64: berlin: Select DW_APB_TIMER_OF
  dt-bindings: sram: sunxi-sram: add V3s compatible string
  MAINTAINERS: Move Sangbeom Kim to credits
  MAINTAINERS: Move Kukjin Kim to credits
  MAINTAINERS: step down as maintainer of UniPhier SoCs and Denali driver
  ARM: multi_v7_defconfig: Build in CONFIG_GPIO_MXC by default
  ARM: imx_v6_v7_defconfig: Build in CONFIG_GPIO_MXC by default
  arm64: defconfig: Build in CONFIG_GPIO_MXC by default
  arm64: dts: meson: odroid-n2 plus: fix vddcpu_a pwm
  ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
  arm64: dts: amlogic: add missing ethernet reset ID
  firmware: arm_scmi: Fix duplicate workqueue name
  firmware: arm_scmi: Fix locking in notifications
  ...

CREDITS

@@ -1910,6 +1910,15 @@ S: 660 Harvard Ave. #7
 S: Santa Clara, CA 95051
 S: USA
 
+N: Kukjin Kim
+E: kgene@kernel.org
+D: Samsung S3C, S5P and Exynos ARM architectures
+
+N: Sangbeom Kim
+E: sbkim73@samsung.com
+D: Samsung SoC Audio (ASoC) drivers
+D: Samsung PMIC (RTC, regulators, MFD) drivers
+
 N: Russell King
 E: rmk@arm.linux.org.uk
 D: Linux/arm integrator, maintainer & hacker

Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml

@@ -33,6 +33,9 @@ properties:
           - const: allwinner,sun4i-a10-system-control
       - const: allwinner,sun8i-a23-system-control
       - const: allwinner,sun8i-h3-system-control
+      - items:
+          - const: allwinner,sun8i-v3s-system-control
+          - const: allwinner,sun8i-h3-system-control
       - items:
           - const: allwinner,sun8i-r40-system-control
           - const: allwinner,sun4i-a10-system-control

MAINTAINERS

@@ -2375,7 +2375,6 @@ F:	sound/soc/rockchip/
 N:	rockchip
 
 ARM/SAMSUNG EXYNOS ARM ARCHITECTURES
-M:	Kukjin Kim <kgene@kernel.org>
 M:	Krzysztof Kozlowski <krzk@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-samsung-soc@vger.kernel.org
@@ -2642,10 +2641,8 @@ F:	drivers/pinctrl/visconti/
 N:	visconti
 
 ARM/UNIPHIER ARCHITECTURE
-M:	Masahiro Yamada <yamada.masahiro@socionext.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier.git
+S:	Orphan
 F:	Documentation/devicetree/bindings/arm/socionext/uniphier.yaml
 F:	Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml
 F:	Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml
@@ -5006,9 +5003,8 @@ T:	git git://linuxtv.org/media_tree.git
 F:	drivers/media/platform/sti/delta
 
 DENALI NAND DRIVER
-M:	Masahiro Yamada <yamada.masahiro@socionext.com>
 L:	linux-mtd@lists.infradead.org
-S:	Supported
+S:	Orphan
 F:	drivers/mtd/nand/raw/denali*
 
 DESIGNWARE EDMA CORE IP DRIVER
@@ -15372,7 +15368,6 @@ F:	security/safesetid/
 
 SAMSUNG AUDIO (ASoC) DRIVERS
 M:	Krzysztof Kozlowski <krzk@kernel.org>
-M:	Sangbeom Kim <sbkim73@samsung.com>
 M:	Sylwester Nawrocki <s.nawrocki@samsung.com>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 S:	Supported
@@ -15407,7 +15402,6 @@ S:	Maintained
 F:	drivers/platform/x86/samsung-laptop.c
 
 SAMSUNG MULTIFUNCTION PMIC DEVICE DRIVERS
-M:	Sangbeom Kim <sbkim73@samsung.com>
 M:	Krzysztof Kozlowski <krzk@kernel.org>
 M:	Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
 L:	linux-kernel@vger.kernel.org
@@ -15489,7 +15483,6 @@ F:	include/linux/clk/samsung.h
 F:	include/linux/platform_data/clk-s3c2410.h
 
 SAMSUNG SPI DRIVERS
-M:	Kukjin Kim <kgene@kernel.org>
 M:	Krzysztof Kozlowski <krzk@kernel.org>
 M:	Andi Shyti <andi@etezian.org>
 L:	linux-spi@vger.kernel.org

arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts

@@ -227,12 +227,12 @@ &ssp3 {
 	/delete-property/ #size-cells;
 	spi-slave;
 	status = "okay";
-	ready-gpio = <&gpio 125 GPIO_ACTIVE_HIGH>;
+	ready-gpios = <&gpio 125 GPIO_ACTIVE_HIGH>;
 
 	slave {
 		compatible = "olpc,xo1.75-ec";
 		spi-cpha;
-		cmd-gpio = <&gpio 155 GPIO_ACTIVE_HIGH>;
+		cmd-gpios = <&gpio 155 GPIO_ACTIVE_HIGH>;
 	};
 };
 

arch/arm/boot/dts/mmp3.dtsi

@@ -296,6 +296,7 @@ camera0: camera@d420a000 {
 				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&soc_clocks MMP2_CLK_CCIC0>;
 				clock-names = "axi";
+				power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>;
 				#clock-cells = <0>;
 				clock-output-names = "mclk";
 				status = "disabled";
@@ -307,6 +308,7 @@ camera1: camera@d420a800 {
 				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&soc_clocks MMP2_CLK_CCIC1>;
 				clock-names = "axi";
+				power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>;
 				#clock-cells = <0>;
 				clock-output-names = "mclk";
 				status = "disabled";

arch/arm/boot/dts/stm32mp157c-ed1.dts

@@ -89,6 +89,14 @@ sd_switch: regulator-sd_switch {
 		states = <1800000 0x1>,
 			 <2900000 0x0>;
 	};
+
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 };
 
 &adc {
@@ -150,11 +158,18 @@ pmic: stpmic@33 {
 
 		regulators {
 			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&vin>;
+			buck2-supply = <&vin>;
+			buck3-supply = <&vin>;
+			buck4-supply = <&vin>;
 			ldo1-supply = <&v3v3>;
 			ldo2-supply = <&v3v3>;
 			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&vin>;
 			ldo5-supply = <&v3v3>;
 			ldo6-supply = <&v3v3>;
+			vref_ddr-supply = <&vin>;
+			boost-supply = <&vin>;
 			pwr_sw1-supply = <&bst_out>;
 			pwr_sw2-supply = <&bst_out>;
 

arch/arm/boot/dts/stm32mp15xx-dkx.dtsi

@@ -80,6 +80,14 @@ sound {
 		dais = <&sai2a_port &sai2b_port &i2s2_port>;
 		status = "okay";
 	};
+
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 };
 
 &adc {
@@ -240,9 +248,18 @@ pmic: stpmic@33 {
 
 		regulators {
 			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&vin>;
+			buck2-supply = <&vin>;
+			buck3-supply = <&vin>;
+			buck4-supply = <&vin>;
 			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&vin>;
 			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&vin>;
+			ldo5-supply = <&vin>;
 			ldo6-supply = <&v3v3>;
+			vref_ddr-supply = <&vin>;
+			boost-supply = <&vin>;
 			pwr_sw1-supply = <&bst_out>;
 			pwr_sw2-supply = <&bst_out>;
 

arch/arm/boot/dts/sun4i-a10.dtsi

@@ -143,7 +143,7 @@ map0 {
 			trips {
 				cpu_alert0: cpu-alert0 {
 					/* milliCelsius */
-					temperature = <850000>;
+					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};

arch/arm/configs/imx_v4_v5_defconfig

@@ -93,6 +93,7 @@ CONFIG_SPI=y
 CONFIG_SPI_IMX=y
 CONFIG_SPI_SPIDEV=y
 CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_MXC=y
 CONFIG_W1=y
 CONFIG_W1_MASTER_MXC=y
 CONFIG_W1_SLAVE_THERM=y

arch/arm/configs/imx_v6_v7_defconfig

@@ -217,6 +217,7 @@ CONFIG_GPIO_PCA953X=y
 CONFIG_GPIO_PCF857X=y
 CONFIG_GPIO_STMPE=y
 CONFIG_GPIO_74X164=y
+CONFIG_GPIO_MXC=y
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_SYSCON=y
 CONFIG_POWER_RESET_SYSCON_POWEROFF=y

arch/arm/configs/multi_v5_defconfig

@@ -166,6 +166,7 @@ CONFIG_SPI_IMX=y
 CONFIG_SPI_ORION=y
 CONFIG_GPIO_ASPEED=m
 CONFIG_GPIO_ASPEED_SGPIO=y
+CONFIG_GPIO_MXC=y
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_GPIO=y
 CONFIG_POWER_RESET_QNAP=y

arch/arm/configs/multi_v7_defconfig

@@ -465,6 +465,7 @@ CONFIG_GPIO_PALMAS=y
 CONFIG_GPIO_TPS6586X=y
 CONFIG_GPIO_TPS65910=y
 CONFIG_GPIO_TWL4030=y
+CONFIG_GPIO_MXC=y
 CONFIG_POWER_AVS=y
 CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_POWER_RESET_AS3722=y

arch/arm/mach-mvebu/coherency_ll.S

@@ -35,13 +35,8 @@ ENTRY(ll_get_coherency_base)
 
 	/*
 	 * MMU is disabled, use the physical address of the coherency
-	 * base address. However, if the coherency fabric isn't mapped
-	 * (i.e its virtual address is zero), it means coherency is
-	 * not enabled, so we return 0.
+	 * base address, (or 0x0 if the coherency fabric is not mapped)
 	 */
-	ldr	r1, =coherency_base
-	cmp	r1, #0
-	beq	2f
 	adr	r1, 3f
 	ldr	r3, [r1]
 	ldr	r1, [r1, r3]

arch/arm64/Kconfig.platforms

@@ -54,6 +54,7 @@ config ARCH_BCM_IPROC
 config ARCH_BERLIN
 	bool "Marvell Berlin SoC Family"
 	select DW_APB_ICTL
+	select DW_APB_TIMER_OF
 	select GPIOLIB
 	select PINCTRL
 	help

arch/arm64/boot/dts/amlogic/meson-axg-s400.dts

@@ -584,3 +584,9 @@ &uart_AO {
 	pinctrl-0 = <&uart_ao_a_pins>;
 	pinctrl-names = "default";
 };
+
+&usb {
+	status = "okay";
+	dr_mode = "otg";
+	vbus-supply = <&usb_pwr>;
+};

arch/arm64/boot/dts/amlogic/meson-axg.dtsi

@@ -171,6 +171,46 @@ soc {
 		#size-cells = <2>;
 		ranges;
 
+		usb: usb@ffe09080 {
+			compatible = "amlogic,meson-axg-usb-ctrl";
+			reg = <0x0 0xffe09080 0x0 0x20>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1_DDR_BRIDGE>;
+			clock-names = "usb_ctrl", "ddr";
+			resets = <&reset RESET_USB_OTG>;
+
+			dr_mode = "otg";
+
+			phys = <&usb2_phy1>;
+			phy-names = "usb2-phy1";
+
+			dwc2: usb@ff400000 {
+				compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+				reg = <0x0 0xff400000 0x0 0x40000>;
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc CLKID_USB1>;
+				clock-names = "otg";
+				phys = <&usb2_phy1>;
+				dr_mode = "peripheral";
+				g-rx-fifo-size = <192>;
+				g-np-tx-fifo-size = <128>;
+				g-tx-fifo-size = <128 128 16 16 16>;
+			};
+
+			dwc3: usb@ff500000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff500000 0x0 0x100000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				maximum-speed = "high-speed";
+				snps,dis_u2_susphy_quirk;
+			};
+		};
+
 		ethmac: ethernet@ff3f0000 {
 			compatible = "amlogic,meson-axg-dwmac",
 				     "snps,dwmac-3.70a",
@@ -187,6 +227,8 @@ ethmac: ethernet@ff3f0000 {
 				      "timing-adjustment";
 			rx-fifo-depth = <4096>;
 			tx-fifo-depth = <2048>;
+			resets = <&reset RESET_ETHERNET>;
+			reset-names = "stmmaceth";
 			status = "disabled";
 		};
 
@@ -1734,6 +1776,16 @@ sd_emmc_c: mmc@7000 {
 				clock-names = "core", "clkin0", "clkin1";
 				resets = <&reset RESET_SD_EMMC_C>;
 			};
+
+			usb2_phy1: phy@9020 {
+				compatible = "amlogic,meson-gxl-usb2-phy";
+				#phy-cells = <0>;
+				reg = <0x0 0x9020 0x0 0x20>;
+				clocks = <&clkc CLKID_USB>;
+				clock-names = "phy";
+				resets = <&reset RESET_USB_OTG>;
+				reset-names = "phy";
+			};
 		};
 
 		sram: sram@fffc0000 {

arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi

@@ -209,7 +209,7 @@ map {
 		};
 
 		ethmac: ethernet@ff3f0000 {
-			compatible = "amlogic,meson-axg-dwmac",
+			compatible = "amlogic,meson-g12a-dwmac",
 				     "snps,dwmac-3.70a",
 				     "snps,dwmac";
 			reg = <0x0 0xff3f0000 0x0 0x10000>,
@@ -224,6 +224,8 @@ ethmac: ethernet@ff3f0000 {
 				      "timing-adjustment";
 			rx-fifo-depth = <4096>;
 			tx-fifo-depth = <2048>;
+			resets = <&reset RESET_ETHERNET>;
+			reset-names = "stmmaceth";
 			status = "disabled";
 
 			mdio0: mdio {
@@ -282,6 +284,8 @@ apb_efuse: bus@30000 {
 				hwrng: rng@218 {
 					compatible = "amlogic,meson-rng";
 					reg = <0x0 0x218 0x0 0x4>;
+					clocks = <&clkc CLKID_RNG0>;
+					clock-names = "core";
 				};
 			};
 

arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts

@@ -19,7 +19,7 @@ &vddcpu_a {
 	regulator-min-microvolt = <680000>;
 	regulator-max-microvolt = <1040000>;
 
-	pwms = <&pwm_AO_cd 1 1500 0>;
+	pwms = <&pwm_ab 0 1500 0>;
 };
 
 &vddcpu_b {

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/meson-gxbb-power.h>
+#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -575,6 +576,8 @@ ethmac: ethernet@c9410000 {
 			interrupt-names = "macirq";
 			rx-fifo-depth = <4096>;
 			tx-fifo-depth = <2048>;
+			resets = <&reset RESET_ETHERNET>;
+			reset-names = "stmmaceth";
 			power-domains = <&pwrc PWRC_GXBB_ETHERNET_MEM_ID>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7-emmc.dts

@@ -20,17 +20,23 @@ / {
 	compatible = "globalscale,espressobin-v7-emmc", "globalscale,espressobin-v7",
 		     "globalscale,espressobin", "marvell,armada3720",
 		     "marvell,armada3710";
+
+	aliases {
+		/* ethernet1 is wan port */
+		ethernet1 = &switch0port3;
+		ethernet3 = &switch0port1;
+	};
 };
 
 &switch0 {
 	ports {
-		port@1 {
+		switch0port1: port@1 {
 			reg = <1>;
 			label = "lan1";
 			phy-handle = <&switch0phy0>;
 		};
 
-		port@3 {
+		switch0port3: port@3 {
 			reg = <3>;
 			label = "wan";
 			phy-handle = <&switch0phy2>;

arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts

@@ -19,17 +19,23 @@ / {
 	model = "Globalscale Marvell ESPRESSOBin Board V7";
 	compatible = "globalscale,espressobin-v7", "globalscale,espressobin",
 		     "marvell,armada3720", "marvell,armada3710";
+
+	aliases {
+		/* ethernet1 is wan port */
+		ethernet1 = &switch0port3;
+		ethernet3 = &switch0port1;
+	};
 };
 
 &switch0 {
 	ports {
-		port@1 {
+		switch0port1: port@1 {
 			reg = <1>;
 			label = "lan1";
 			phy-handle = <&switch0phy0>;
 		};
 
-		port@3 {
+		switch0port3: port@3 {
 			reg = <3>;
 			label = "wan";
 			phy-handle = <&switch0phy2>;

arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi

@@ -13,6 +13,10 @@
 / {
 	aliases {
 		ethernet0 = &eth0;
+		/* for dsa slave device */
+		ethernet1 = &switch0port1;
+		ethernet2 = &switch0port2;
+		ethernet3 = &switch0port3;
 		serial0 = &uart0;
 		serial1 = &uart1;
 	};
@@ -120,7 +124,7 @@ ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			switch0port0: port@0 {
 				reg = <0>;
 				label = "cpu";
 				ethernet = <&eth0>;
@@ -131,19 +135,19 @@ fixed-link {
 				};
 			};
 
-			port@1 {
+			switch0port1: port@1 {
 				reg = <1>;
 				label = "wan";
 				phy-handle = <&switch0phy0>;
 			};
 
-			port@2 {
+			switch0port2: port@2 {
 				reg = <2>;
 				label = "lan0";
 				phy-handle = <&switch0phy1>;
 			};
 
-			port@3 {
+			switch0port3: port@3 {
 				reg = <3>;
 				label = "lan1";
 				phy-handle = <&switch0phy2>;

arch/arm64/configs/defconfig

@@ -500,6 +500,7 @@ CONFIG_GPIO_ALTERA=m
 CONFIG_GPIO_DWAPB=y
 CONFIG_GPIO_MB86S7X=y
 CONFIG_GPIO_MPC8XXX=y
+CONFIG_GPIO_MXC=y
 CONFIG_GPIO_PL061=y
 CONFIG_GPIO_RCAR=y
 CONFIG_GPIO_UNIPHIER=y

drivers/firmware/arm_scmi/base.c

@@ -197,6 +197,8 @@ static int scmi_base_implementation_list_get(const struct scmi_handle *handle,
 			protocols_imp[tot_num_ret + loop] = *(list + loop);
 
 		tot_num_ret += loop_num_ret;
+
+		scmi_reset_rx_to_maxsz(handle, t);
 	} while (loop_num_ret);
 
 	scmi_xfer_put(handle, t);

drivers/firmware/arm_scmi/clock.c

@@ -192,6 +192,8 @@ scmi_clock_describe_rates_get(const struct scmi_handle *handle, u32 clk_id,
 		}
 
 		tot_rate_cnt += num_returned;
+
+		scmi_reset_rx_to_maxsz(handle, t);
 		/*
 		 * check for both returned and remaining to avoid infinite
 		 * loop due to buggy firmware

drivers/firmware/arm_scmi/common.h

@@ -147,6 +147,8 @@ int scmi_do_xfer_with_response(const struct scmi_handle *h,
 			       struct scmi_xfer *xfer);
 int scmi_xfer_get_init(const struct scmi_handle *h, u8 msg_id, u8 prot_id,
 		       size_t tx_size, size_t rx_size, struct scmi_xfer **p);
+void scmi_reset_rx_to_maxsz(const struct scmi_handle *handle,
+			    struct scmi_xfer *xfer);
 int scmi_handle_put(const struct scmi_handle *handle);
 struct scmi_handle *scmi_handle_get(struct device *dev);
 void scmi_set_handle(struct scmi_device *scmi_dev);

drivers/firmware/arm_scmi/driver.c

@@ -402,6 +402,14 @@ int scmi_do_xfer(const struct scmi_handle *handle, struct scmi_xfer *xfer)
 	return ret;
 }
 
+void scmi_reset_rx_to_maxsz(const struct scmi_handle *handle,
+			    struct scmi_xfer *xfer)
+{
+	struct scmi_info *info = handle_to_scmi_info(handle);
+
+	xfer->rx.len = info->desc->max_msg_size;
+}
+
 #define SCMI_MAX_RESPONSE_TIMEOUT	(2 * MSEC_PER_SEC)
 
 /**

drivers/firmware/arm_scmi/notify.c

@@ -1403,15 +1403,21 @@ static void scmi_protocols_late_init(struct work_struct *work)
 				"finalized PENDING handler - key:%X\n",
 				hndl->key);
 			ret = scmi_event_handler_enable_events(hndl);
+			if (ret) {
+				dev_dbg(ni->handle->dev,
+					"purging INVALID handler - key:%X\n",
+					hndl->key);
+				scmi_put_active_handler(ni, hndl);
+			}
 		} else {
 			ret = scmi_valid_pending_handler(ni, hndl);
-		}
-		if (ret) {
-			dev_dbg(ni->handle->dev,
-				"purging PENDING handler - key:%X\n",
-				hndl->key);
-			/* this hndl can be only a pending one */
-			scmi_put_handler_unlocked(ni, hndl);
+			if (ret) {
+				dev_dbg(ni->handle->dev,
+					"purging PENDING handler - key:%X\n",
+					hndl->key);
+				/* this hndl can be only a pending one */
+				scmi_put_handler_unlocked(ni, hndl);
+			}
 		}
 	}
 	mutex_unlock(&ni->pending_mtx);
@@ -1468,7 +1474,7 @@ int scmi_notification_init(struct scmi_handle *handle)
 	ni->gid = gid;
 	ni->handle = handle;
 
-	ni->notify_wq = alloc_workqueue("scmi_notify",
+	ni->notify_wq = alloc_workqueue(dev_name(handle->dev),
 					WQ_UNBOUND | WQ_FREEZABLE | WQ_SYSFS,
 					0);
 	if (!ni->notify_wq)

drivers/firmware/arm_scmi/perf.c

@@ -304,6 +304,8 @@ scmi_perf_describe_levels_get(const struct scmi_handle *handle, u32 domain,
 		}
 
 		tot_opp_cnt += num_returned;
+
+		scmi_reset_rx_to_maxsz(handle, t);
 		/*
 		 * check for both returned and remaining to avoid infinite
 		 * loop due to buggy firmware

drivers/firmware/arm_scmi/reset.c

@@ -36,9 +36,7 @@ struct scmi_msg_reset_domain_reset {
 #define EXPLICIT_RESET_ASSERT	BIT(1)
 #define ASYNCHRONOUS_RESET	BIT(2)
 	__le32 reset_state;
-#define ARCH_RESET_TYPE		BIT(31)
-#define COLD_RESET_STATE	BIT(0)
-#define ARCH_COLD_RESET		(ARCH_RESET_TYPE | COLD_RESET_STATE)
+#define ARCH_COLD_RESET		0
 };
 
 struct scmi_msg_reset_notify {

drivers/firmware/arm_scmi/sensors.c

@@ -166,6 +166,8 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 		}
 
 		desc_index += num_returned;
+
+		scmi_reset_rx_to_maxsz(handle, t);
 		/*
 		 * check for both returned and remaining to avoid infinite
 		 * loop due to buggy firmware

drivers/firmware/arm_scmi/smc.c

@@ -149,6 +149,6 @@ static const struct scmi_transport_ops scmi_smc_ops = {
 const struct scmi_desc scmi_smc_desc = {
 	.ops = &scmi_smc_ops,
 	.max_rx_timeout_ms = 30,
-	.max_msg = 1,
+	.max_msg = 20,
 	.max_msg_size = 128,
 };

drivers/soc/ti/ti_sci_pm_domains.c

@@ -91,7 +91,7 @@ static struct generic_pm_domain *ti_sci_pd_xlate(
 	struct genpd_onecell_data *genpd_data = data;
 	unsigned int idx = genpdspec->args[0];
 
-	if (genpdspec->args_count < 2)
+	if (genpdspec->args_count != 1 && genpdspec->args_count != 2)
 		return ERR_PTR(-EINVAL);
 
 	if (idx >= genpd_data->num_domains) {

drivers/tee/tee_core.c

@@ -200,7 +200,8 @@ int tee_session_calc_client_uuid(uuid_t *uuid, u32 connection_method,
 	int name_len;
 	int rc;
 
-	if (connection_method == TEE_IOCTL_LOGIN_PUBLIC) {
+	if (connection_method == TEE_IOCTL_LOGIN_PUBLIC ||
+	    connection_method == TEE_IOCTL_LOGIN_REE_KERNEL) {
 		/* Nil UUID to be passed to TEE environment */
 		uuid_copy(uuid, &uuid_null);
 		return 0;